Instruction/ maintenance manual of the product QP242 FujiFilm
Go to page of 55
ProLINE-RoadRunner English PN 096-0230-0 02 Operator ’ s Guide for Fuji MFU: QP242, QP351 ,IP 3 ™ CONTENTS Overview Installation Job Setup Operation Maintenance Troubleshooting.
Data I/O has made a conscientiou s effort to ensure that the information in this document is accurate and complete. Data I/O assumes no liability for errors, or for any incidental, consequential, indi.
1 ProLINE-Road Runner Opera tor’s Guide A ProLINE-RoadRunner for Fuji........... 2 Jobs and S t atistics........... 3 External V iew ........... 4 Internal Component s........... 5 Control Panel Light s........... 6 Control Panel Bu ttons...........
2 ProLINE-Road Runner Opera tor’s Guide A Dat a I/O is proud to introduce a revolutionary new inline solution for high-volume programming of electronic product s. ProLINE-RoadRunner: 1. T ak es programmable devices from a reel... 2. Places them in sockets and programs them with your dat a.
3 ProLINE-Road Runner Opera tor’s Guide A T askLink™ for Windows ® is required to process devices on ProLINE-RoadRunner . T askLink allows you to create and manage a job dat abase and it analyzes job st atist ics. PCMCIA cards are used to transfer jobs and statistics between T askLink and RoadRunner .
4 ProLINE-Road Runner Opera tor’s Guide A 1. SMT Communications Connection 2. Power and Air Connections 3. Power Switch 4. Handhold for lif ting 5. PCMCIA Card Slot 6. Control Panel 7. Conveyor Belt 8. Mechanical Interface to the Multi-Feeder Unit 9.
5 ProLINE-Road Runner Opera tor’s Guide A 1. Cover T ape T ake-Up Reel 2. T ape-In Module 3. PNP Probes, Precisor , and Cover 4. Reject Bin 5. Socket Adapter , Actuator Plate, and Programmer 3 1.
6 ProLINE-Road Runner Opera tor’s Guide A Control Panel Light s 1. Blue - Stop Indicator . User intervention is required, or the unit is p aused. (Do not remove PCMCIA card unless blue lamp is li t.) 2. Y ellow - Caution Indicator . Correct a problem or the machine will stop.
7 ProLINE-Road Runner Opera tor’s Guide A 1. Star t - s t art or resume the chosen job. 2. Menu - exit to the previous menu, —or show the next message (deleting the current one), —or deselect an item. 3. Up and Down Ar rows - move through menu items.
8 ProLINE-Road Runner Opera tor’s Guide A Operator Menus are visible on the RoadRunner control p anel, and can be navigated by using the Up Ar r ow and Down Ar row buttons. Pressing the Menu button displays the menu that is one level up. If you are at the main menu, pressing Menu will have no effect.
9 ProLINE-Road Runner Opera tor’s Guide A View th e Supervisor Menus by inserting a PCMCIA c ard with supervisor authority . (The menus on this p age and the next two pages are in addition to the Operator Menus.) Supervisor (Administrator) authorization is set in T askLink.
10 ProLINE-Road Runner Opera tor’s Guide A Refer to the previous pa ge for the main menu. Note that many of th e values shown, such as the T each and Network menus, are f or example only .
11 ProLINE-Road Runner Opera tor’s Guide A Refer to the main Supervisor Menu (2 pages back) for orient ation. NOTE: Programmer Diags are only available with a Diagnostic Adapter Board. 1 Actuation duration is set by the Soc ket Adapter . For more information about menu commands, see Chapter 3 of the ProLINE-RoadRunner Owner ’s Manual.
12 ProLINE-Road Runner Opera tor’s Guide A W arnings and Cautions Compressed Air Point air hoses away from body . Always wear ap proved eye protectio n. Loud Noise Sound pressure levels may excee d 85db. Hearing prote ction is recommended for prol onged exposure at this level.
13 ProLINE -RoadRunner Operator’s Guid e A Mounting on the Feeder Bank ...... 14 Connecting Power and Air ...... 16 Running the Self-T est ...... 18 Installation Chapter 2.
14 ProLINE-Road Runner Opera tor’s Guide A T o mount RoadRunner onto an MFU: 1. Align and push the communica- tions cable into the MFU. NOTE: T o allows access to RoadRunner , do not use the ten right-most slot positions on the MFU. 2. While holding RoadRunner at a slight nose-down angle, let the nose rest on the MFU.
15 ProLINE -RoadRunner Operator’s Guid e A 3. Stil l holding it at an angle, slide it forward as far as it will go. (The nose will fit under the lip on the MFU.) 4. Lower RoadRunner and jiggle it to ensure that the angle bracket has settled into the spring clamp on the MFU.
16 ProLINE-Road Runner Opera tor’s Guide A T o connect the power and the air: 1. T urn the RoadRunner power switch to the Off (0) position. 2. Grasp the air hose behind the “quick connect” collar and push it firmly onto th e male fitting. The collar must be allowed to move back as it goes onto the fitting.
17 ProLINE -RoadRunner Operator’s Guid e A 3. Connect to a grounded power source using a cable with a st andard IEC 320 plug. RoadRunner accept s power between 100 and 240 V AC, 50/60Hz. 4. Align and push the communications cable end into the RoadRunner connector .
18 ProLINE-Road Runner Opera tor’s Guide A T o run the Self-T est: 1. T urn the pow er switch On (I). All the control p anel indicator lamps light up. When the Self- T est finishes, the blue lamp will remain on and the version number will display . If all the indicator lamp s st art blinking, a serious error has occurred.
19 ProLINE-Road Runner Opera tor’s Guide A Inserting a Job Card ..... 20 Changing the Precisor ..... 22 Changing the Actuator P late..... 24 Changing the Socket Adapter..... 26 Adjusting the T ape-In Module ..... 28 Loading a Reel of Devices ..... 30 Aligning the T ape Pockets .
20 ProLINE-RoadR unner Operat or’s Guide T o run a job, insert a T askLink job card into the PCMCIA card slot. Use only TYPE I or TYPE II PCMCIA cards. T o inse rt a job card: 1. If the power switch is on, make sure the blue lamp is lit. Inserting a Job Card Electrostatic disc harge may cause damage .
21 ProLINE-Road Runner Opera tor’s Guide A 2. Slide the job card into the PCMCIA card slot. NOTE: When fully inserted, the job card extends slightly from the PCMCIA card slot. NOTE: Do not eject the card unless the blue lamp is lit (or the power is off).
22 ProLINE-RoadR unner Operat or’s Guide T o change the precisor: 1. Select Jo b , then End , wait for the blue lamp to light and turn the power Off (0). 2. Lif t off the Robotics Cover . 3. St arting at one end, pull the precisor down off the magnet, and then pull the other end off.
23 ProLINE-Road Runner Opera tor’s Guide A 4. When inserting the new precisor , make sure that the part number faces up and that the small holes near the precisor edge fit over the dowel pins on the PNP head. There should be no visible gap between the precisor and the head.
24 ProLINE-RoadR unner Operat or’s Guide T o change the Act uator Plate: 1. Select Jo b , then End , wait for the blue lamp to light and turn the power Off (0). 2. Lif t off the Robotics Cover . Once power is off, the PNP Head can be moved by hand to allow access to the A ctuator Plate.
25 ProLINE-Road Runner Opera tor’s Guide A 3. Pull the Actuator Plate to slide it out of the grooved brackets. NOTE: The Actuator Plate must be out to access or change the Socket Adapter . T o change the Soc ket Adapter , see the procedure on the following pa g e .
26 ProLINE-RoadR unner Operat or’s Guide T o change the Socket Adapter (with the Actuator Plate removed): 1. Make sure the power is Off (0). 2. Unscrew the two captive scre ws and lift the adapter bracket. 2 2 Changing the Socket Adapter Caution: Electrostatic Disc harge may cause damage.
27 ProLINE-Road Runner Opera tor’s Guide A 3. Without touching the gold cont act surfaces on the bottom of the adapter , lif t the adapter free. 4. Insert the correct adapter , making sure that it seats on the dowel pins. NOTE: Each type of device may have its own Socket Adapter .
28 ProLINE-RoadR unner Operat or’s Guide If you have an Adjust able T ape-In Module, you may need to adjust the ta p e w i dt h . Adjust able T ape-In Module only— If the etched number on the 3-Position Sp acer does not match your t ape wid th dimension (mm): 1.
29 ProLINE-Road Runner Opera tor’s Guide A 3. Rot ate the 3-Position Sp acer with your finger until you read 16, 24 or 32, corresponding to your t ape width. 4. Retighten the Position Locking Screw . 5. Rot ate the Peel Bar counterclockwise 180 degrees to the up position.
30 ProLINE-RoadR unner Operat or’s Guide T o load and thread dev ice t ape: 1. Place a reel onto the RoadRunner spindle. 2. Lock the reel in place by rot ating the brass button on the spindle end. 3. Insert the device t ape into the T ape-In Module and onto the sprocket.
31 ProLINE-Road Runner Opera tor’s Guide A 5. When the t ape is advanced p ast the Peel Bar , separate the cover t ape from the device t ape. 6. Thread the cover t ape up through the cover tape p ath and att ach it to the Cover T ape T ak e-Up Reel.
32 ProLINE-RoadR unner Operat or’s Guide T o align the tape pocket s: 1. Select Align P ock et from the Operator Menu. 2. Press the Up Ar r ow button to advance the t ape until the next t ape pocket center hole is approximately centered at the pick point alignment mark.
33 ProLINE-Road Runner Opera tor’s Guide A Running a Job ........ . 34 Pausing or S topping a Job ......... 35 Ending a Job ......... 36 Emptying the Reject Bin ........ . 38 Emptying Cover T ape ......... 39 Shutting Down .. ....... 40 Rest arting a Job .
34 ProLINE-Road Runner Opera tor’s Guide A T o run a job: 1. Insert a job card into the PCMCIA card slot. 2. Clear the conveyor belt of any unneeded devices.
35 ProLINE-Road Runner Opera tor’s Guide A T o pause at the end of the current operation: 1. Press Pause on the control pa n e l . T o instantly stop in an emergency situation: 2. Press the Emer gency Stop (E-Stop) button. The E-Stop does not stop the assembly machine.
36 ProLINE-Road Runner Opera tor’s Guide A Whenever you are going to change job cards, you must first end the current job. T o end the current job: 1.
37 ProLINE-Road Runner Opera tor’s Guide A 3. Clear away excess devic es from the conveyor belt. 4. Empty the Reject B in. (See next heading.) 5. Empty the Cover T ape T ake-Up Reel.
38 ProLINE-Road Runner Opera tor’s Guide A T o empt y the Reject Bin: 1. Press the Pause button. 2. Pull the Reject Bin out by grabbing the finger t ab and then lif t up and out. When reinserting the R eject Bin, be sure the bin is comp letely lowered so that the t ab is positioned out of the path of the probes.
39 ProLINE-Road Runner Opera tor’s Guide A T o empt y the Cover T ape T ake-U p Reel: 1. Press Pause . 2. Cut the cover tape, leaving enough slack to reatt ach. 3. Pull the T ake- Up Reel straight out. (Reels with slot s require rot ating before pulling off.
40 ProLINE-Road Runner Opera tor’s Guide A T o shut down RoadRunner: 1. Press Pause . 2. Select End J ob from the Job Menu and wait for all devices to be placed on the belt.
41 ProLINE-Road Runner Opera tor’s Guide A 5. Empty the Reject B in. 6. Remove and empty the T ake-Up Reel. (For more, see the previous heading.) 7. Remove the air hose or shut off the air flow . NOTE: When disconnecting the air hose, pull the connector collar back as you pull the connector off.
42 ProLINE-Road Runner Opera tor’s Guide A T o restart RoadRunner af ter a pause or an emergency stop: 1. T urn the Emer gency Stop button clockwise to release it, if needed. 2. Press Menu until the main level menu is displayed 3. Select Align P ock et.
43 ProLINE-Road Runner Opera tor’s Guide A Cleaning with Air ......... . 44 Cleaning with Alcohol.......... 45 Running the Self-T est.......... 46 Maintenance Chapter 5.
44 ProLINE-Road Runner Opera tor’s Guide A T o prevent dust accumulat ion, inject compressed air into the following component areas: 1. T ape-In Module (weekly). 2. Socket s (daily). Socket s should be opened and closed by hand while air is injected.
45 ProLINE-Road Runner Opera tor’s Guide A T o prevent dust and oil accumulations, clean the following component areas with isopropyl alcohol on a lint-free cloth. • Chassis and Covers (every 3 months). • Conveyor belt (daily). See "Device Rot a tion" in the T roubleshooting chapter .
46 ProLINE-Road Runner Opera tor’s Guide A Run the Self-T est procedure approximately once a week. T o run the Self-T est procedure: 1. Press Pause . 2. Clear all devices from the socket s and from the conveyor belt. 3. T oggle the power switch off and then back on.
47 ProLINE-Road Runner Opera tor’s Guide A Viewing Errors.. .......... 48 Enabling a Socket........... . 50 Clearing Jammed T ape............ 51 Device Rot ation.
48 ProLINE-Road Runner Opera tor’s Guide A Viewing Errors T o vie w and correct errors: 1. Messages will appear in the keypad display . 2. Check the condition—t ape p ath, Reject Bin, etc.—implied by the message. If you cannot correct the error condition, cont act a service technician .
49 ProLINE-Road Runner Opera tor’s Guide A Sto p Caution Motor Cont roller not responding Some common error messages are listed below . For more information see “T roubleshooting” in the ProLINE-RoadRunner Owner ’s Manual . 1 Twist the Emer gency Stop bu tton to rel ease it.
50 ProLINE-Road Runner Opera tor’s Guide A If a socket r epeatedly becomes disabled, RoadRunner should be serviced. T o re-ena ble a disabled socket: 1. Select Sock et from the top level menu. 2. Arrow down and select the disabled socket from the Socket menu.
51 ProLINE-Road Runner Opera tor’s Guide A If the t ape jams, an error message displays and the blue lamp illuminates. T o clear the tape p ath: 1. Press the Emer gency Stop button (to continue the job later) or select Job , then End . T urn the power off.
52 ProLINE-Road Runner Opera tor’s Guide A Device Rot ation If devices rotate excessively on the conveyor belt: 1. Press Pause . W ait for all t he devices to get picked from the belt.
53 ProLINE-Road Runner Opera tor’s Guide A Wo rldwide Data I/O Corporation Shippin g address: 10525 Willows Road N.E. Redmond, W A USA 98052 Mailing address: P .O. Box 97046 Redmond, W A USA 98073-9746 T ele pho ne: 425-867-6870 USA Only: 1-800 -332- 82 46 Fax: 425-882-1043 E-mail: s upport@da taio.
An important point after buying a device FujiFilm QP242 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought FujiFilm QP242 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data FujiFilm QP242 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, FujiFilm QP242 you will learn all the available features of the product, as well as information on its operation. The information that you get FujiFilm QP242 will certainly help you make a decision on the purchase.
If you already are a holder of FujiFilm QP242, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime FujiFilm QP242.
However, one of the most important roles played by the user manual is to help in solving problems with FujiFilm QP242. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device FujiFilm QP242 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
