EN
Graco logo
Official user manual

Graco Fluid Filter (222812)

22 pages·553 KB·Musical Toy Instrument·PDF·ENDEFRITNLJA
Graco Fluid Filter (222812)
Table of Contents 6 sections Parts - Models C50260 and 222812 · Parts - Model 235516 · Parts - Model 222909 · Parts - Model 241081 · … ShowHide
Page 1 of the Graco Fluid Filter (222812) user manual — Model 222812
Page 1 · click to enlarge
Page 1

Instructions–Parts List

19 LITER (5 GALLON) Wiper Plates

308049U

For straight-sided or tapered pails. Fit Check-Mate Pumps on a Pneumatic Elevator Cart or Ram. For professional use only.

Not approved to European explosive atmosphere requirements.

U.S. Patent No. 5,117,998

See page 2 for Table of Contents and List of Models.

Model 222812

Model 222909

Page 2 of the Graco Fluid Filter (222812) user manual — List of Models
Page 2 · click to enlarge
Page 2

Table of Contents

List of Models 2 Symbols 3 Warnings 3 Installation (All Wiper Plates) 5 Installation on a Ram

Installation on a Ram (Stainless Steel Plates) 10 Installation on a Cart (Stainless Steel Plates) 12 Parts Drawings and Lists 14 Accessories 21 Technical Data 21 Graco Standard Warranty 22 Graco Information 22

(Carbon Steel or Aluminum Plates) 6 Installation on a Cart

(Carbon Steel or Aluminum Plates) 8

List of Models

Model No.SeriesPlate MaterialWiper MaterialBackup MaterialInstallation PagesParts Pages 222812BCarbon SteelBuna-NUHMWPE6–914 235516BCarbon SteelPTFE-coatedUHMWPE6–915 222909AStainless SteelPTFE-coatedUHMWPE10–1316–17 241081ACarbon SteelBuna-NUHMWPE6–918 918409BCarbon SteelBuna-NUHMWPE6–919 C50260BCarbon SteelBuna-NUHMWPE6–914

2 308049

Page 3 of the Graco Fluid Filter (222812) user manual — Warning Symbol
Page 3 · click to enlarge
Page 3

Symbols

Warning Symbol

Caution Symbol

CAUTION

This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions.

This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions.

WARNING INSTRUCTIONSEQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury. This equipment is for professional use only. Read all instruction manuals, tags, and labels before operating the equipment. Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco distributor. Do not alter or modify this equipment. Use only genuine Graco parts and accessories. Check equipment daily. Repair or replace worn or damaged parts immediately. Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings. Comply with all applicable local, state, and national fire, electrical, and safety regulations. MOVING PARTS HAZARD Moving parts, such as the priming piston and wiper plate, can pinch or amputate your fingers. Keep clear of all moving parts when starting or operating the pump. Keep hands and fingers away from the priming piston during operation and whenever the pump is charged with air. Keep your hands away from the wiper plate and the lip of the pail while the ram is operating. Before servicing the equipment, follow the Pressure Relief Procedure on page 5 to prevent the equipment from starting unexpectedly.

308049 3

Page 4 of the Graco Fluid Filter (222812) user manual — Notes
Page 4 · click to enlarge
Page 4

Notes

4 308049

Page 5 of the Graco Fluid Filter (222812) user manual — Pressure Relief Procedure
Page 5 · click to enlarge
Page 5

Installation (All Wiper Plates)

Pressure Relief Procedure

3. Shut off the main air bleed valve (required in your system).
4. Unlock the gun/valve trigger safety.

SKIN INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally. Fluid under high pressure can be injected through the skin and cause serious injury. To reduce the risk of an injury from injection, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you:

5. Hold a metal part of the gun/valve firmly to the side of a grounded metal pail, and trigger the gun/valve to relieve pressure.
6. Lock the gun/valve trigger safety.
7. Open the drain valve (required in your system) and/or the pump bleeder valve, having a container ready to catch the drainage.

are instructed to relieve the pressure, stop spraying/dispensing, check or service any of the system equipment, or install or clean the spray tip/nozzle.

8. Leave the drain valve open until you are ready to spray again.

If you suspect that the spray tip/nozzle or hose is completely clogged, or that pressure has not been fully relieved after following the steps above, very slowly loosen the tip guard retaining nut or hose end coupling and relieve pressure gradually, then loosen completely. Now clear the tip/nozzle or hose.

1. Lock the gun/valve trigger safety.
2. Close the pump air bleed valve (required in your system).

308049 5

Page 6 of the Graco Fluid Filter (222812) user manual — Maintenance
Page 6 · click to enlarge
Page 6

Installation on a Ram

(Carbon Steel or Aluminum Plates)

Installation

b. To reinstall the spacer for use with a straight sided pail, first make sure the large diameter of the spacer (19) is facing down. Work the spacer up over the wiper plate by hand, so it is completely above the flange (D) of the wiper plate. See Fig. 3. Then, working from the top, use a screwdriver to position the spacer between the flange (D) and the wipers (E). See Fig. 4.

Reference letters and numbers in the text refer to Figs. 1–4 and the Parts Drawings on pages 14–15.

MOVING PARTS HAZARD Moving parts can pinch or amputate your fingers. When the pump is operating and when raising or lowering the ram, keep your fingers and hands away from the priming piston and the lip of the pail.

4. Connect a 610 mm (24 in.), 1/4 in. (6.3 mm) OD nylon tube (F) with a 1/8 npt(f) fitting (H) from the ram’s air assist tube fitting (G) to the air assist check valve (21) on the wiper plate.
5. Refer to the separate ram and pump manuals for set-up and operating instructions.

To reduce the risk of serious injury, whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5.

Maintenance

1. Relieve the pressure.
2. Install the wiper plate (A) onto the pump intake (B), with the wiper plate vent handle (C) facing the front of the ram. Secure by tightening the setscrew (3). See Fig. 1.

If the wiper plate does not come out of the pail easily when the pump is being raised, the air assist tube (F), fitting (H), and check valve (21) may be plugged. This prevents air from reaching the underside of the plate to assist in raising it from the pail.

3. The wiper plate is supplied for use with 19 liter (5 gallon) straight sided pails, but it can be easily modified for use with tapered pails. See steps a and b.

a. To use the wiper plate with tapered pails, the large spacer (19) must be removed. Work- ing from the bottom, use a screwdriver to pry the spacer loose. Work it upward so it is com- pletely above the flange (D) of the wiper plate. See Fig. 2. Next, by hand, angle the spacer and work it off the plate, pulling it down over the flange and bottom wipers (E). See Fig. 3. Save the spacer, as it is required for other applications.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5.

Relieve the pressure. Refer to the Parts Drawings on pages 14–15 and disassemble the air assist check valve as shown. Clear the tube (F) and the port in the wiper plate. Clean all parts of the check valve assem- bly, and reassemble.

6 308049

Page 7 of the Graco Fluid Filter (222812) user manual — E
Page 7 · click to enlarge
Page 7

Installation on a Ram

(Carbon Steel and Aluminum Plates)

Installing the Wiper Plate on a Ram (Model 222812 shown; large diameter of spacer facing down)

To use Model 222812 and 235516, Plates with tapered pails, the spacer (19) must be removed. See page 6, and Figs. 2–4.

E

0248A Fig. 2

G

F

E

B C

H

06540A Fig. 1

E

0251A Fig. 4

308049 7

Page 8 of the Graco Fluid Filter (222812) user manual — Maintenance
Page 8 · click to enlarge
Page 8

Installation on a Cart

(Carbon Steel and Aluminum Plates)

Installation

b. To use the wiper plate with tapered pails, the large spacer (19) must be removed. Work- ing from the bottom, use a screwdriver to pry the spacer loose. Work it upward so it is com- pletely above the flange (D) of the wiper plate. See Fig. 6. Next, by hand, angle the spacer and work it off the plate, pulling it down over the flange and bottom wipers (E). See Fig. 7. Save the spacer, as it is required for other applications.

Reference letters and numbers in the text refer to Figs. 5–8 and the Parts Drawings on pages 14–15.

MOVING PARTS HAZARD Moving parts can pinch or amputate your fingers. When the pump is operating and when raising or lowering the ram, keep your fingers and hands away from the priming piston and the lip of the pail.

4. Install Cart Accessory Kit 224376. See 308087 for details.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5.

5. Refer to the separate cart and pump manuals for set-up and operating instructions.
1. Relieve the pressure.
2. Install the wiper plate (A) onto the pump intake (B), with the wiper plate vent handle (C) facing the front of the cart. Secure by tightening the setscrew (3). See Fig. 5.

Maintenance

If the wiper plate does not come out of the pail easily when the pump is being raised, the air assist tube (F), fitting (H), or check valve (21) may be plugged. This prevents air from reaching the underside of the plate to assist in raising it from the pail.

3. The wiper plate is supplied for use with 19 liter (5 gallon) straight sided pails on a ram. It must be modified for use with the pneumatic elevator cart. See steps a and b, following.

a. To use the wiper plate with straight sided pails, the large spacer (19) must be inverted. Working from the bottom, use a screwdriver to pry the spacer loose. Work it upward so it is completely above the flange (D) of the wiper plate. See Fig. 6. Next, by hand, angle the spacer and work it off the plate, pulling it down over the flange and bottom wipers (E). See Fig. 7. Turn the spacer so the large diameter is facing up. Work the spacer up over the wiper plate by hand, so it is completely above the flange (D) of the wiper plate. Working from the top, use a screwdriver to position the spacer between the flange (D) and the wipers (E). See Fig. 8.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5.

Relieve the pressure. Refer to the Parts Drawings on pages 14–15 and disassemble the air assist check valve as shown. Clear the tube (F) and the port in the wiper plate. Clean all parts of the check valve assem- bly, and reassemble.

8 308049

Page 9 of the Graco Fluid Filter (222812) user manual — E
Page 9 · click to enlarge
Page 9

Installation on a Cart

(Carbon Steel and Aluminum Plates)

Installing the Wiper Plate on a Pneumatic Elevator Cart (Model 222812 shown; large diameter of spacer facing up)

To use Model 222812 and 235516 Plates with tapered pails, the spacer (19) must be removed. See page 8, and Figs. 6–8.

Part of Kit 224376 (See 308087).

19 D E

0248A Fig. 6

F

H

E

0249A Fig. 7

3 B

0252D Fig. 5

E

0251A D

308049 9

Page 10 of the Graco Fluid Filter (222812) user manual — Maintenance
Page 10 · click to enlarge
Page 10

Installation on a Ram

(Stainless Steel Plates)

Installation

4. Connect a 965 mm (38 in.), 6.3 mm (1/4 in.) OD tube (F) from the ram’s air assist valve (G) to the elbow (H) on the wiper plate.

Reference letters and numbers in the text refer to Figs. 9–12 and the Parts Drawing on page 16.

5. Refer to the separate ram and pump manuals for set-up and operating instructions.

Operating the Air Assist Valve Handle

MOVING PARTS HAZARD Moving parts can pinch or amputate your fingers. When the pump is operating and when raising or lowering the ram, keep your fingers and hands away from the priming piston and lip of the pail.

The ram’s air assist valve (G) directs air under the wiper plate, making it easier to pull the plate out of the pail. For the air assist valve to function, you must open a passage for the air with the valve handle (J). Practice using the handle a few times, until you are familiar with its use.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5.

1. Stop the pump. Relieve the pressure.
1. Relieve the pressure.
2. To open a passage for air to get under the plate, rotate the handle (J) 45 clockwise and pull it upward (it should travel about 13 mm [1/2 in.] up and down).
2. Install the wiper plate (A) onto the pump intake (B), with the wiper plate vent handle (C) facing the left of the ram. Secure by tightening the setscrews (17). See Fig. 9.
3. Turn the ram director valve to UP. Press the air assist valve (G), and hold it in until the plate clears the top of the pail.
3. The wiper plate is supplied for use with 19 liter (5 gallon) straight sided pails, but it can be easily modified for use with tapered pails. See steps a and b
4. To close the air passage, push the handle (J) down and rotate it 45 counterclockwise to lock.

a. To use the wiper plate with tapered pails, the large spacer (8) must be removed. Work- ing from the bottom, use a screwdriver to pry the spacer loose. Work it upward so it is com- pletely above the flange (D) of the wiper plate. See Fig. 10. Next, by hand, angle the spacer and work it off the plate, pulling it down over the flange and bottom wipers (E). See Fig. 11. Save the spacer, as it is required for other applications.

Maintenance

If the wiper plate does not come out of the pail easily when the pump is being raised, the air assist tube (F), elbow (H), or valve (J) may be plugged. A plugged valve prevents air from reaching the underside of the plate to assist in raising it from the pail.

b. To reinstall the spacer for use with a straight sided pail, first make sure the large diameter of the spacer (8) is facing down. Work the spacer up over the wiper plate by hand, so it is completely above the flange (D) of the wiper plate. See Fig. 11. Then, working from the top, use a screwdriver to position the spacer between the flange (D) and the wipers (E). See Fig. 12.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5.

Relieve the pressure. Refer to the Parts Drawing on page 16 and disassemble the air assist valve (J) as shown. Clear the hose (F) and the elbow (H) in the wiper plate. Clean all parts of the valve, and reas- semble.

10 308049

Page 11 of the Graco Fluid Filter (222812) user manual — G
Page 11 · click to enlarge
Page 11

Installation on a Ram

(Stainless Steel Plates)

Installing the Wiper Plate on a Ram (large diameter of spacer facing down)

Graco Fluid Filter (222812) — (Stainless Steel Plates) diagram (page 11)
Fig. 1 · (Stainless Steel Plates)

To use Model 222909 Plate with a tapered pail, the spacer (8) must be removed. See page 10, and Figs. 10–12.

Graco Fluid Filter (222812) — (Stainless Steel Plates) diagram (page 11)
Fig. 2 · (Stainless Steel Plates)

G

F

H

B

06754C Fig. 9

308049 11

Page 12 of the Graco Fluid Filter (222812) user manual — Maintenance
Page 12 · click to enlarge
Page 12

Installation on a Cart

(Stainless Steel Plates)

Installation

4. Install Cart Accessory Kit 224376. See 308199 for details.

Reference letters and numbers in the text refer to Figs. 13–16 and the Parts Drawing on page 16.

5. Refer to the separate cart and pump manuals for set-up and operating instructions.

Operating the Air Assist Valve Handle

MOVING PARTS HAZARD Moving parts can pinch or amputate your fingers. When the pump is operating and when raising or lowering the ram, keep your fingers and hands away from the priming piston and the lip of the fluid container.

The cart’s air assist toggle valve (G) directs air under the wiper plate, making it easier to pull the plate out of the pail. Refer to manual 308199 for instructions on changing pails using the air assist valve.

For the air assist valve to function, you must open a passage for the air with the valve handle (J). Practice using the handle a few times, until you are familiar with its use.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5.

1. Relieve the pressure.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5.

2. Install the wiper plate (A) onto the pump intake (B), with the wiper plate vent handle (C) facing the left of the cart. Secure by tightening the setscrews (17). See Fig. 13.
1. Relieve the pressure.
3. The wiper plate is supplied for use with 19 liter (5 gallon) straight sided pails on a ram. It must be modified for use with the pneumatic elevator cart. See steps a and b following.
2. To open a passage for air to get under the plate, rotate the handle (J) 45 clockwise and pull it upward (it should travel about 13 mm [1/2 in.] up and down).

a. To use the wiper plate with straight sided pails, the large spacer (8) must be inverted. Working from the bottom, use a screwdriver to pry the spacer loose. Work it upward so it is completely above the flange (D) of the wiper plate. See Fig. 14. Next, by hand, angle the spacer and work it off the plate, pulling it down over the flange and bottom wipers (E). See Fig. 15. Turn the spacer so the large diameter is facing up. Work the spacer up over the wiper plate by hand, so it is completely above the flange (D) of the wiper plate. Working from the top, use a screwdriver to position the spacer between the flange (D) and the wipers (E). See Fig. 16.

3. To close the air passage, push the handle (J) down and rotate it 45 counterclockwise to lock.

Maintenance

If the wiper plate does not come out of the pail easily when the pump is being raised, the air assist tube (F), elbow (H), or valve (J) may be plugged. A plugged valve prevents air from reaching the underside of the plate to assist in raising it from the pail.

b. To use the wiper plate with tapered pails, the large spacer (8) must be removed. Work- ing from the bottom, use a screwdriver to pry the spacer loose. Work it upward so it is com- pletely above the flange (D) of the wiper plate. See Fig. 14. Next, by hand, angle the spacer and work it off the plate, pulling it down over the flange and bottom wipers (E). See Fig. 15. Save the spacer, as it is required for other applications.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5.

Relieve the pressure. Refer to the Parts Drawing on page 16 and disassemble the air assist valve (J) as shown. Clear the hose (F) and the elbow (H) in the wiper plate. Clean all parts of the valve, and reas- semble.

12 308049

Page 13 of the Graco Fluid Filter (222812) user manual — B
Page 13 · click to enlarge
Page 13

Installation on a Cart

(Stainless Steel Plates)

Installing the Wiper Plate on a Pneumatic Elevator Cart (large diameter of spacer facing up)

Graco Fluid Filter (222812) — (Stainless Steel Plates) diagram (page 13)
Fig. 3 · (Stainless Steel Plates)

To use Model 222909 Plate with a tapered pail, the spacer (8) must be removed. See page 12, and Figs. 14–16.

Part of Kit 224376; see 308199.

Graco Fluid Filter (222812) — (Stainless Steel Plates) diagram (page 13)
Fig. 4 · (Stainless Steel Plates)
Graco Fluid Filter (222812) — (Stainless Steel Plates) diagram (page 13)
Fig. 5 · (Stainless Steel Plates)

B

308049 13

Page 14 of the Graco Fluid Filter (222812) user manual — 0254B
Page 14 · click to enlarge
Page 14

Model C50260, Series B Model 222812, Series B Carbon Steel Wiper Plate with Buna-N Wiper and UHMWPE Backup

0254B

Ref. Part No. No. Description Qty

Ref. Part No. No. Description Qty

1 101831 PIN, spring, straight 1 2 177542 HANDLE 1 3 100421 SETSCREW, socket hd, cup point; 5/16–18 x 3/8 in. (9.5 mm) long 2 4 166560 STEM, probe 1 5 184420 WIPER; synthetic rubber 1 6 109469 SCREW, machine, flat-hd; zinc-plated carbon steel; 1/4–20 x 1 in. (25 mm) long 8 9 184419 CLAMP, retaining zinc-plated carbon steel 1 12 222764 PLATE, wiper; zinc-plated carbon steel 1

13 109458 O-RING; fluoroelastomer 1 14 102040 NUT, hex, self-locking; with nylon insert; 1/4–20 unc–3b 8 15 184421 WIPER; polyethylene (Model 222812 only) 1 16 184418 CLAMP, retaining; zinc-plated carbon steel 1 19 276049 SPACER; polyurethane 1 21 114317 VALVE, check, air assist 1

Keep these spare parts on hand to reduce down time.

14 308049

Page 15 of the Graco Fluid Filter (222812) user manual — Parts - Model 235516
Page 15 · click to enlarge
Page 15

Model 235516, Series B Carbon Steel Wiper Plate with PTFE-coated Wiper and UHMWPE Backup

Ref. Part No. No. Description Qty

Ref. Part No. No. Description Qty

1 101831 PIN, spring, straight 1 2 177542 HANDLE 1 3 100421 SETSCREW, socket hd, cup point; 5/16–18 x 3/8 in. (9.5 mm) long 1 4 166560 STEM, probe 1 5 184552 WIPER; nitrile/PTFE 1 6 109469 SCREW, machine, flat-hd; zinc-plated carbon steel; 1/4–20 x 1 in. (25 mm) long 8 9 184419 CLAMP, retaining zinc-plated carbon steel 1 12 222764 PLATE, wiper; zinc-plated carbon steel 1

13 109458 O-RING; fluoroelastomer 1 14 102040 NUT, hex, self-locking; with nylon insert; 1/4–20 unc–3b 8 15 184421 WIPER; polyethylene 1 16 184418 CLAMP, retaining; zinc-plated carbon steel 1 19 276049 SPACER; polyurethane 1 20 184551 WIPER; polyethylene 1 21 114317 VALVE, check, air assist 1

Keep these spare parts on hand to reduce down time.

308049 15

Page 16 of the Graco Fluid Filter (222812) user manual — Valve Assembly Procedure (see Detail below)
Page 16 · click to enlarge
Page 16

Model 222909, Series A Stainless Steel Wiper Plate with PTFE-coated Wiper and UHMWPE Backup

Valve Assembly Procedure (see Detail below)

1. Assemble all wipers and the clamp (9) to the plate (5) as shown at left, before assembling the valve.
2. Insert the seal (19) in the hole (K) of the collar (1). Align the hole and the flat of the guide (15) with the hole (L) in the collar, and install the guide. Screw the elbow (11) into the hole (L) until snug. Do not overtighten. The guide (15) should be held from rotating by the elbow (11) but should not be clamped firmly in place.

PTFE side faces down, toward fluid.

Located inside assembly of items 1 and 5.

Graco Fluid Filter (222812) — Valve Assembly Procedure (see Detail below) diagram (page 16)
Fig. 6 · Valve Assembly Procedure (see Detail below)
3. Slide the nut (13) and seal (19) onto the stem (14). Press the pin (12) into the hole in the stem (14) until the pin bottoms out.
4. Insert the stem (14) into the hole (K) so the pin (12) travels in the slot of the guide (15). Push the seal (19) down into the hole (K) and tighten the nut (13) snugly – do not overtighten. (Stem (14) should not rotate more than 90 ).
5. Operate the valve a few times to ensure proper assembly.
Graco Fluid Filter (222812) — Valve Assembly Procedure (see Detail below) diagram (page 16)
Fig. 7 · Valve Assembly Procedure (see Detail below)

16 308049

Page 17 of the Graco Fluid Filter (222812) user manual — Parts - Model 235516
Page 17 · click to enlarge
Page 17

Model 222909, Series A Stainless Steel Wiper Plate with PTFE-coated Wiper and UHMWPE Backup

Ref. Part No. No. Description Qty

Ref. Part No. No. Description Qty

1 184471 COLLAR, wiper plate; sst 1 2 184481 STEM, probe; sst 1 3 109482 O-RING; PTFE 1 4 103972 SCREW, drive, u-type; 0.188 in. (5 mm) long 3 5 222915 PLATE, wiper; sst 1 6 184421 WIPER; polyethylene 1 7 184552 WIPER; nitrile/PTFE 1 8 276049 SPACER; polyurethane 1 9 184477 CLAMP, retaining; sst 1 10 109478 NUT, lock, hex; w/nylon insert; 1/4–20 unc–2b 8 11 109506 ELBOW, tube fitting, 90; 1/8 npt(m) x 1/4 in. (6.3 mm) tube size 1

12 109479 PIN, spring, straight; 3/32 in. size x 3/8 in. (9.5 mm) long 1 13 184482 NUT, retainer; sst 1 14 184479 STEM, valve; sst 1 15 184531 GUIDE, valve; sst 1 16 109458 O-RING; fluoroelastomer 1 17 109477 SCREW, cap, hex head; 5/16–18 unc–2a; 1/2 in. (13 mm) long 2 19 184530 SEAL, valve; PTFE 2 20 184551 WIPER; polyethylene 1 21 114317 VALVE, check, air assist 1

Keep these spare parts on hand to reduce down time.

308049 17

Page 18 of the Graco Fluid Filter (222812) user manual — Parts - Model 241081
Page 18 · click to enlarge
Page 18

Model 241081, Series A Carbon Steel Wiper Plate with Buna-N Wiper and UHMWPE Backup

Ref. Part No. No. Description Qty

Ref. Part No. No. Description Qty

1 101831 PIN, spring, straight 1 2 177542 HANDLE 1 3 100421 SETSCREW, socket hd, cup point; 5/16–18 x 3/8 in. (9.5 mm) long 2 4 166560 STEM, probe 1 5 194146 WIPER; synthetic rubber 1 6 109469 SCREW, machine, flat-hd; zinc-plated carbon steel; 1/4–20 x 1 in. (25 mm) long 8 9 194151 CLAMP, retaining zinc-plated carbon steel 1 12 241080 PLATE, wiper; zinc-plated carbon steel 1

13 109458 O-RING; fluoroelastomer 1 14 102040 NUT, hex, self-locking; with nylon insert; 1/4–20 unc–3b 8 15 194147 WIPER; polyethylene 1 16 194149 CLAMP, retaining; zinc-plated carbon steel 1 19 276049 SPACER; polyurethane 1 21 C20467 VALVE, check, air assist 1 23 111842 FITTING, elbow, pipe 45 1 24 155665 UNION, adapter 1 25 208391 VALVE, ball 1

Keep these spare parts on hand to reduce down time.

18 308049

Page 19 of the Graco Fluid Filter (222812) user manual — 0254B
Page 19 · click to enlarge
Page 19

Model 918409, Series B Carbon Steel Wiper Plate with Buna-N Wiper and UHMWPE Backup

0254B

Ref. Part No. No. Description Qty

Ref. Part No. No. Description Qty

1 101831 PIN, spring, straight 1 2 177542 HANDLE 1 3 100421 SETSCREW, socket hd, cup point; 5/16–18 x 3/8 in. (9.5 mm) long 2 4 166560 STEM, probe 1 5 184420 WIPER; synthetic rubber 1 6 109469 SCREW, machine, flat-hd; zinc-plated carbon steel; 1/4–20 x 1 in. (25 mm) long 8 9 184419 CLAMP, retaining zinc-plated carbon steel 1 12 222764 PLATE, wiper; zinc-plated carbon steel 1

13 109458 O-RING; fluoroelastomer 1 14 102040 NUT, hex, self-locking; with nylon insert; 1/4–20 unc–3b 8 15 184421 WIPER; polyethylene 1 16 184418 CLAMP, retaining; zinc-plated carbon steel 1 17 276049 SPACER; polyurethane 1 18 C20467 FITTING, nipple, reducer 1 19 111842 FITTING, elbow, pipe 45 1 20 208391 VALVE, ball 1 21 155665 UNION, adapter 1

Keep these spare parts on hand to reduce down time.

308049 19

Page 20 of the Graco Fluid Filter (222812) user manual — Notes
Page 20 · click to enlarge
Page 20

Notes

20 308049

Page 21 of the Graco Fluid Filter (222812) user manual — Technical Data
Page 21 · click to enlarge
Page 21

Accessories

USE GENUINE GRACO PARTS AND ACCESSORIES

Wiper Conversion for Model 222812

Shield Kit 223689

If the fluid you are pumping is not compatible with the 184420 synthetic rubber wiper which is standard on Model 222812, order part no. 184551 polyethylene wiper and 184552 PTFE-coated wiper. These parts are standard on Model 235516. Refer to page 13, items 5 and 20, for proper installation.

Place on the surface of the fluid before the plate enters the pail, to cover the fluid side of the 19 liter (5 gal.) wiper plate and keep it clean. For use with ram- mounted pumps only. Package of 10 disposable poly- ethylene shields. Shields may be reused, if desired, by removing excess material with a squeegee.

Technical Data

Outer diameter (wiper) Model 222812, 235516, 222909, 918409, C50260: 289 mm (11.38 in.);

Model 241081330 mm (12.99 in.)

Inner diameter (neck) 64.58 mm (2.54 in.)

Wetted parts Model 222812, 241081, 918409, C50260: Zinc-Plated Carbon Steel, Synthetic Rubber, Ultra-High Molecular Weight Polyethylene, Cork, Polyurethane, Polyethylene, fluoroelastomer

Model 235516: Zinc-Plated Carbon Steel, Nitrile, PTFE, Ultra-High Molecular Weight Polyethylene, Cork, Polyurethane, Polyethylene, fluoroelastomer

Model 222909: 304 and 316 Stainless Steel, Nitrile, PTFE, Ultra-High Molecular Weight Polyethylene, Polyurethane, Polyethylene, fluoroelastomer

Category Data · 308049 21

Page 22 of the Graco Fluid Filter (222812) user manual — Graco Information
Page 22 · click to enlarge
Page 22

Graco Standard Warranty

Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accor- dance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub- stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais- sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com

TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you: Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 308049

Graco HeadquartersMinneapolis International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 Copyright 1990, Graco Inc. is registered to ISO 9001

www.graco.com Revised 08/2010

22 308049

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Graco Fluid Filter (222812)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Graco Fluid Filter (222812)

Be the first to ask — other owners or our team will answer.

Original document

Graco Fluid Filter (222812) manual PDF

22 pages·553 KB·Musical Toy Instrument·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…