EN
Graco logo
Official user manual

Graco 234409

8 pages·377 KB·Automobile Parts·PDF·ENDEFRITNLJA
Graco 234409
Table of Contents 6 sections Installation · Operation · Maintenance · Parts · … ShowHide
Page 1 of the Graco 234409 user manual — Instructions - Parts List
Page 1 · click to enlarge
Page 1

Instructions - Parts List

In-line Air Filters and Coalescers

309919D

Graco 234409 — Instructions - Parts List diagram (page 1)
Fig. 1 · Instructions - Parts List

Maximum Working Pressure 175 psi (1.2 MPa, 12 bar) Maximum Temperature 150° F (65° C)

Part No.DescriptionAir Inlet npt(f)Air Outlet npt(f)Air Flow Capacity at 100 psi (0.7 MPa, 7 bar) 234397Air Filter with auto drain Removes liquids and contaminants down to .01microns.1/2”1/2”70 CFM 234402Stage 1 - Air Filter with auto drain Removes water and contaminants down to 5 microns.1/2”1/2”115 CFM 234403Stage 2 - Coalescer with auto drain Removes oil and sub-micronic particles down to .01 microns.1/2”1/2”35 CFM 234405Includes Air Filter 234406 and Coalescer 234407, see below1/2”1/2”70 CFM 234406Stage 1 - Air Filter with auto drain Removes water and contaminants down to 5 microns.1/2”1/2”108 CFM 234407Stage 2 - Coalescer with auto drain Removes oil and sub-micronic particles down to .01 microns.1/2”1/2”70 CFM 234408Air Filter with auto drain Removes liquids and contaminants down to 5 microns.3/4”3/4”300 CFM 234409Coalescer with auto drain Removes oil and sub-micronic particles down to .01 microns.3/4”3/4”115 CFM

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001

Page 2 of the Graco 234409 user manual — Shop Air Piping Layout
Page 2 · click to enlarge
Page 2

Installation

3. Install a main air shut-off valve upstream from the air controls to isolate them for service.
1. Before installing air line components, blow out the pipe line to remove debris. Be sure air to the regulator is clean. Erratic operation or loss of regulation is usually caused by dirt in the regulator.
4. Install system so air flows through filters in the direction noted on top of filter.
5. A minimum 1/2” npt piping is recommended. Avoid using too many fittings, couplings, etc., which will restrict air flow.
2. Install the unit as close as possible to the equipment it serves.

Shop Air Piping Layout

Slopes down and away Recommended 4” (117 mm) drop in 50’ (15.24 m) galvanized

Graco 234409 — Shop Air Piping Layout diagram (page 2)
Fig. 2 · Shop Air Piping Layout

Main Air Line 3/4” (19 mm) minimum 1-1/4” (32 mm) optimum

  • Main Air Line stand pipe should not be smaller than compressor outlet size.
  • A minimum of 25 ft. (7.62 m) from compressor to first filter outlet is required to cool air [50 ft. (15.24 m) optimum]

Installation

Page 3 of the Graco 234409 user manual — Installation
Page 3 · click to enlarge
Page 3
Minimum Pipe Size Recommendations CompressorMain Air Line SizeCapacityLengthSize 1-1/2 - 2 HP6 - 9 CFMany3/4” (19 mm) 3 - 5 HP12 - 20 CFMUp to 200 ft. (61 m)3/4” (19 mm) Over 200 ft. (61 m)1” (25.4 mm)) 5 - 10 HP20 - 40 CFMUp to 100 ft. (30.5)3/4” (19 mm) Over100-200ft.(30.5-61m)1” (25.4 mm) Over 200 ft. (61 m)1-1/4” (31.8 mm) 10 - 15 HP40 - 60 CFMUp to 100 ft. (30.5)3/4” (19 mm) Over100-200ft.(30.5-61m)1-1/4” (31.8) Over 200 ft. (61 m)1-1/2” (38.1)
Air Pressure Drop Through Hose, by hose length and ID psi (Kpa, bar) Air Hose Inside Diameter4 ft. (1.22 m)10 ft. (3.05 m)15 ft. (4.6 m)20 ft. (6.1 m)25 ft. (7.62 m)50 ft. (15.24 m) 1/4 in. (6.4 mm) 40 psi (276 kPa, 2.8 bar) 50 psi (345 kPa, 3.4 bar) 60 psi (414 kPa, 4.1 bar) 70 psi (483 kPa, 4.8 bar) 80 psi (552 kPa, 5.5 bar) 90 psi (621 kPa, 6.2 bar)6 (41, .4) 7.5 (52, .5) 9 (62, .6) 10.75 (74, .7) 12.25 (84, .8) 14 (97, 1)8 (55, .6) 10 (69, .7) 12.5 (86, .9) 14.5 (100, 1) 16.5(114,1.1) 18.75 (129, 1.3)9.5 (66, .7) 12 (83, .8) 14.5 (100, .1) 17 (117, 1.2) 19.5 (134, 1.3) 22 (152, 1.5)11 (76, .8) 14 (97, 1) 16.75(115,1.2) 19.5 (134, 1.3) 22.5 (155, 1.6) 25.25 (172, 1.7)12.75 (88, 0.9) 16 (110, 1.1) 19 (131, 1.3) 22.5 (155, 1.6) 25.5 (176, 1.8) 29 (200, 2)24 (165, 1.7) 28 (193, 1.9) 31 (214, 2.1) 34 (234, 2.3) 37 (255, 2.6) 39.5 (169, 2.7) 5/16 in. (7.9 mm) 40 psi (276 kPa, 2.8 bar) 50 psi (345 kPa, 3.4 bar) 60 psi (414 kPa, 4.1 bar) 70 psi (483 kPa, 4.8 bar) 80 psi (552 kPa, 5.5 bar) 90 psi (621 kPa, 6.2 bar)2.25 (16, .2) 3 (21, .2) 3.75 (26, .3) 4.5(31, .3) 5.5 (38, .4) 6.5 (45, .4)2.75 (19, .2) 3.5 (24, .2) 4.5 (31, .3) 5.25 (36, .4) 6.25 (43, .4) 7.5 (52, .5)3.25 (22, .2) 4 (28, .3) 5 (34, .3) 6 (41, .4) 7 (48, .5) 8.5 (59, .6)3.5 (24, .2) 4.5 (31, .3) 5.5 (38, .4) 6.75 (47, .5) 8 (55, .6) 9.5 (66, .7)4 (28, .3) 5 (34, .3) 6 (41, .4) 7.25 (50, .5) 8.75 (60, .6) 10.5 (72, .7)8.5 (59, .6) 10 (69, .7) 11.5 (79, .8) 13 (90, .9) 14.5 (100, 1) 16 (110, 1.1)

Installation

Page 4 of the Graco 234409 user manual — Coalescer Pressure Drop Indicator
Page 4 · click to enlarge
Page 4

Operation

Pressure Relief Procedure

Auto Drain

The following is a basic pressure relief procedure. Be sure to follow the specific pressure relief procedure in your spray gun and/or fluid supply equipment manuals.

When the bowl is pressurized, the piston travels down against the spring and closes the drain opening. When the bowl is depressurized (i.e., overnight when system is shut down), the spring lifts the piston from the seal, allowing the bowl to drain.

1. Close the main air shut-off valve.
2. Trigger the gun or dispense valve and open any drain valves to relieve pressure.

You can push the piston stem on the bottom of the bowl to manually drain it.

Coalescer Pressure Drop Indicator

The differential pressure drop indicator provides early detection of a clogged coalescing filter element. As the filter element becomes clogged, the red indicator starts to rise while air is flowing through the unit. When the pressure drop across the element reaches 10-12 psi (69-83 kPa, 0.7-0.8 bar), the red indicator will be in full view, and the element should be replaced. Failure to replace the element when the pressure drop exceeds 10 psi (69 kPa, 0.7 bar) will affect your air quality and tool efficiency.

Operation

Page 5 of the Graco 234409 user manual — Cleaning
Page 5 · click to enlarge
Page 5

Maintenance

Coalescers with Auto Drain

  • Relieve the pressure before cleaning, checking or repairing equipment. Follow Pressure Relief Procedure , page 4.

It is recommended that Air Filter 234402 be installed upstream of the coalescing filter to remove 5 micron and larger size particles and sep- arate large droplets of moisture from the air line.

  • Check system at least once per shift to ensure proper drainage.
  • To maintain maximum filtering efficiency and avoid excessive pressure drop, filters must be kept clean.

Air Filters with Auto Drain

Cleaning

You do not need to remove the complete coalescer from the line to clean it.

Cleaning

You do not need to remove the complete filter from the line to clean it.

1. Follow the Pressure Relief Procedure , page 4. Be sure to shut off the air supply and depressurize the filter.
1. Follow the Pressure Relief Procedure , page 4.
2. Clean all parts with cleaning solvent and blow out filter body.
2. Clean all parts with cleaning solvent and blow out coalescer body.
3. Replace coalescer element.
3. Wash filter element in cleaning solvent. Blow the filter out from the inside.

Maintenance

Page 6 of the Graco 234409 user manual — Air Filter 234408
Page 6 · click to enlarge
Page 6

Parts

Air Filter and Coalescer Assembly 234405

Includes Air Filter 234406 (below) and Coalescer 234407 (page 7).

Air Filters

Air Filter 234402†

Ref. No. Part No. Description 1 288788 Auto Drain 2 288791 O-Ring 3 288790 Baffle Kit 4 288809 Filter Element 5 288808 Bracket (not shown)

† Used with both Desiccant 234401 (see Manual 309921) and Membrane 234481 (see Manual 309920) Air Drying Systems.

Air Filter 234406

Ref. No. Part No. Description 1 289192 Auto Drain 2 288791 O-Ring 3 288790 Baffle Kit 4 288809 Filter Element

Air Filter 234408

Ref. No. Part No. Description 1 289192 Auto Drain 2 288791 O-Ring 4 288807 Filter Element

Push to manually drain (open)

Parts

Page 7 of the Graco 234409 user manual — Coalescer 234409
Page 7 · click to enlarge
Page 7

Air Filter/Coalescers

Air Filter 234397**

Ref. No. Part No. Description 11 288788 Auto Drain 12 288791 O-Ring 13 288792 Pop-up Indicator Repair Kit 14 289193 Coalescer Element

** Used with Membrane Air Drying System 234418. Refer to Man- ual 309920.

Coalescer 234403*

Ref. No. Part No. Description 11 288788 Auto Drain 12 288791 O-Ring 13 288792 Pop-up Indicator Repair Kit 14 289194 Coalescer Element

* Used with Desiccant Air Drying System 234401. Refer to Manual 309921.

Coalescer 234407

Ref. No. Part No. Description 11 289192 Auto Drain 12 288791 O-Ring 13 288792 Pop-up Indicator Repair Kit 14 289193 Coalescer Element

Coalescer 234409

Ref. No. Part No. Description 11 289192 Auto Drain 12 288791 O-Ring 13 288792 Pop-up Indicator Repair Kit 14 118559 Coalescer Element

Push to manually drain (open)

Parts

Page 8 of the Graco 234409 user manual — GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Page 8 · click to enlarge
Page 8

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Phone Numbers

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6921 or Toll Free: 1-800-328-0211, Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

This manual contains English. MM 309919

Graco HeadquartersMinneapolis International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

www.graco.com

6/2003, Rev. 5/2007

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Graco 234409

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Graco 234409

Be the first to ask — other owners or our team will answer.

Original document

Graco 234409 manual PDF

8 pages·377 KB·Automobile Parts·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…