EN
Graco logo
Official user manual

Graco 24F531

14 pages·1.3 MB·Automobile Parts·PDF·ENDEFRITNLJA
Graco 24F531
Table of Contents 10 sections Warnings · Installation · Typical Installations · General Installation Information · … ShowHide
Page 1 of the Graco 24F531 user manual — Related Manuals:
Page 1 · click to enlarge
Page 1

Instructions

Diesel Exhaust Fluid (DEF) System 3A1189G

EN

For pumping diesel exhaust fluid. Not approved for use in European explosive atmosphere locations. For professional use only.

50 psi (0.3 MPa, 3.4 bar) Maximum Fluid Working Pressure 50 psi (0.3 MPa, 3.4 bar) Maximum Air Input Pressure

Graco 24F531 — EN diagram (page 1)
Fig. 1

Model No. 24F531 Wall mounted with meter

Graco 24F531 — EN diagram (page 1)
Fig. 2

Model No. 24F878 Wall mounted without meter

Model No. 24F947 Drum mounted without meter

Model No. 24M499 Drum mounted with meter

Related Manuals:

313048 Meter 308981 Husky Pump

Model 24F947 · Model 24F531

Page 2 of the Graco 24F531 user manual — WARNING
Page 2 · click to enlarge
Page 2

Warnings

The following general warnings are for the setup, use, grounding, maintenance, and repair of this equipment. Addi- tional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appear- ing in the body of the manual refer to these general warnings. When these symbols appear throughout the manual, refer back to these pages for a description of the specific hazard.

WARNING

FIRE AND EXPLOSION HAZARD When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be aware that flammable fumes can ignite or explode. To help prevent fire and explosion:

  • Use equipment only in well ventilated area.
  • Eliminate all ignition sources, such as cigarettes and portable electric lamps.
  • Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.
  • Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
  • Ground all equipment in the work area.
  • Use only grounded hoses.
  • If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.
  • Keep a working fire extinguisher in the work area.

PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury.

  • Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing equipment.
  • Tighten all fluid connections before operating the equipment.
  • Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

TOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swal- lowed. • Read MSDSs to know the specific hazards of the fluids you are using.

  • Route exhaust away from work area. If diaphragm ruptures, fluid may be exhausted into the air.
  • Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
Page 3 of the Graco 24F531 user manual — WARNING
Page 3 · click to enlarge
Page 3

WARNING

EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury.

  • Do not operate the unit when fatigued or under the influence of drugs or alcohol.
  • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.
  • Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer.
  • Do not leave the work area while equipment is energized or under pressure. Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
  • Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.
  • Do not alter or modify equipment.
  • Use equipment only for its intended purpose. Call your distributor for information.
  • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
  • Do not kink or over bend hoses or use hoses to pull equipment.
  • Keep children and animals away from work area.
  • Comply with all applicable safety regulations.

PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns. This equipment includes but is not limited to:

  • Protective eye wear, and hearing protection.
  • Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

Follow this Pressure Relief Procedure whenever you:

  • Are instructed to relieve pressure.
1. Turn OFF air supply to pump (F IG . 1).
2. Open the nozzle.
  • Stop dispensing.
3. Be sure you have a container ready to catch drainage.
  • Check, clean or service any system equipment.
  • Install or clean fluid nozzles.

Pressure Relief Procedure

Page 4 of the Graco 24F531 user manual — G
Page 4 · click to enlarge
Page 4

Typical Installations

Model 24F531 - Wall Mounted, with Meter Model 24F878 - Wall Mounted, no Meter

Graco 24F531 — Typical Installations diagram (page 4)
Fig. 3 · Typical Installations

G

J

D

K

H

A Pump B Bleed-type master air valve (required for pump) C Air supply line D Pump air regulator E Fluid supply hose F Suction kit G Wall mounting bracket H Fluid nozzle J Meter K Nozzle bracket and bath L Safety valve - set to 50 psi (3.4 bar, 0.34 MPa)

Key

Page 5 of the Graco 24F531 user manual — Installation
Page 5 · click to enlarge
Page 5

Model 24F947 - Drum Mounted without Meter Model 24M499 - Drum Mounted with Meter

Graco 24F531 — Installation diagram (page 5)
Fig. 4 · Installation

A Pump B Bleed-type master air valve (required for pump) C Air supply line D Pump air regulator E Fluid supply hose F Suction kit

G Fluid nozzle J Nozzle tray and bath K Drum bracket L Safety valve - set to 50 psi (3.4 bar, 0.34 MPa) M Meter N Fluid Nozzle

Key

Page 6 of the Graco 24F531 user manual — Installation Date
Page 6 · click to enlarge
Page 6

General Installation Information

Identification Label for CE Mark

Locate the Diesel Exhaust Fluid (DEF) System identifi- cation label adhered to the mounting bracket.

  • The Typical Installation illustrations provided on pages 4 - 5 are only guidelines for installing system components. Contact your Graco distributor for assistance in planning a system to suit your needs.

Use a permanent marker or ink pen to write the installa- tion date in the space provided and circle the Part Num- ber for the model you ordered.

  • To ensure your system is compatible with fluids being pumped, always use genuine Graco replacement parts and accessories.

FIG. 3 is provided to assist you in finding the location of this label on the bracket and the Date Code field on the label.

  • Tighten all connections firmly to avoid air and/or fluid leaks.
Graco 24F531 — Identification Label for CE Mark diagram (page 6)
Fig. 5 · Identification Label for CE Mark
  • Storage tanks should be securely anchored to prevent shifting or tipping when empty or full.

NOTICE

To maintain the integrity and purity of the AUS32 (Aqueous Urea Solution 32.5%) and ensure proper operation of equipment:

  • Once the system is assembled it must remain sealed to insure the integrity of the fluid. Breaking the seal on the system can lead to fluid contamination.
Graco 24F531 — NOTICE diagram (page 6)
Fig. 6
  • After dispensing DEF, drain all the fluid from the nozzle, making sure it is pointing downward when stored in the nozzle holder. DEF remaining in the nozzle tip and exposed to air will crystallize and can plug the nozzle.
  • DO NOT lay the dispensing nozzle on the ground or on any surface that may contaminate the nozzle tip and compromise the purity of the DEF.
Graco 24F531 — NOTICE diagram (page 6)
Fig. 7

Installation Date

Wall Bracket Label · Drum Bracket Label

Page 7 of the Graco 24F531 user manual — Pump
Page 7 · click to enlarge
Page 7

Pump

1. Using the hardware provided install the air controls to the air inlet of the pump as shown in F IG . 4. Use a minimum 1/4 in. (6.3 mm) ID air hose.

For complete pump instructions refer to the pump instruction manual included with your system.

2. Install an air line quick disconnect coupler onto the end of the air supply line (C) and screw the matting fitting into the pump air inlet snugly. Do not connect the coupler to the fitting yet.
  • If necessary, change the orientation of the fluid inlet and outlet ports on the pump. See pump instruction manual for this procedure.
  • Retorque bolts per specifications.

Numerals used in the following instructions refer to ref- erence numbers used in the Parts Lists provided on pages 10 - 11.

Alpha letters included in the following instructions refer to letters shown in Typical Installation examples (FIG. 1 - FIG. 2, pages 4 - 5).

1. Screw the fluid supply hose (9) fluid fitting into the pump inlet snuggly. Do not overtighten.

A bleed-type master air valve (B) is required in your system to relieve trapped air between the valve and the pump. Trapped air can cause the pump to cycle unexpectedly, which could result in serious injury from fluid splashing in the eyes or on skin, injury from moving parts or contamination from hazardous fluids.

Fluid Suction Kit (6) - 24F532

Numerals used in the following instructions refer to ref- erence numbers used in the Parts Lists provided on pages 10 - 11.

The DEF System includes a Fluid Suction Kit containing the following parts - Drum Coupler (6a), Drum Insert (6b) and Suction Line (6c).

Locate one bleed-type master air valve (B) close to the pump and use it to relieve trapped air (FIG. 4). For drum mounted installations only, also locate a second master air valve upstream from all air line accessories and use it to isolate them during cleaning and repair.

Graco 24F531 — Pump diagram (page 7)
Fig. 8 · Pump
Graco 24F531 — Pump diagram (page 7)
Fig. 9 · Pump
  • If using with a large tote: Do NOT trim the suction line.
  • If using with a 55 gallon drum: Trim the suction line to 39 inches (991 mm). Remove all burrs.

Fluid Supply Hose · Air Line · 6a E

Page 8 of the Graco 24F531 user manual — Meter (10) Installation: Models 24F531 and 24M499
Page 8 · click to enlarge
Page 8

The suction line is designed to allow for full evacuation of the container so it will bend slightly when installed.

4. Install meter (10a) to fitting (10c). Wrench tighten.
5. Install fitting (10e) into meter. Wrench tighten.
1. Connect suction tube (6c) to drum insert (6b) to pump.
6. Install hose (9) into fitting (10e).
2. Insert suction line (6c) into drum.

Mounting Bracket (2) Installation

3. Install drum coupler (6a) into drum insert (6b)
  • When installing bracket, be sure the mounting surface can support the weight of the pump, hoses and all accessories, as well as the stress caused during operation.
4. Connect hose (E) to pump fitting. Use a flat-blade screw driver to tighten hose clamp (F).
5. Connect the air supply line (C) to the air controls.
  • On all installations mount the pump using screws and nuts provided.

Nozzle (3) Installation: Models 24F878 and 24F947

  • Always keep nozzle bath tray filled with water.

Numerals used in the following instructions refer to ref- erence numbers used in the Parts Lists provided on pages 10 - 11.

Wall Mounting Kit 24F870 (2)Models 24F531 and 24F878 only

Wall mounted DEF System Models 24F531 and 24F878 include a Mounting Bracket Kit containing the following parts - Screws (2a), Screws (2b), Washers (2c), Plain Washers (2d), Hex Nuts (2e), Mounting Plate (2f), Noz- zle Bath Holder (2g), Nozzle Holder Bracket (2h) and screws (2j). The Mounting Bracket and Nozzle Holder are also identified as items J and M on the Typical Installation Diagram provided on page 4.

Wall Mount Model24F878
1. Install hose (9) into back of nozzle (3). Wrench tighten.
2. Install other end of hose (9) into pump outlet fitting.
Drum Mount Model24F947
1. Install clamp over end of fluid supply hose (9).
1. Determine location to install mounting plate (2f).
2. Push end of fluid supply hose (9) over end of nozzle (3) fitting.
2. Use holes the plate (2f) as a template. Mark mounting hole locations. Use a drill to predrill mounting holes in mounting surface.
3. Position clamp over fitting and hose end. Use a flat blade screw driver to tighten screw and secure clamp to the end of hose over barbed fitting.
3. Use screws (2a) (provided) to install plate (2f).
4. Align holes in nozzle holder bracket (2h) with holes in plate (2f). Use screws (2b), nuts (2e) and washers (2d)(provided) to install meter tray plate.
4. Install other end of hose (9) into pump outlet fitting.

Meter (10) Installation: Models 24F531 and 24M499

5. Place nozzle bath (2g) in nozzle holder bracket (2h). Fill bath with water. Keep meter bath filled with water at all times.

Uses Meter Kit 24H293 that includes the following parts: -Meter (10a), Swivel (10b), Fitting (10c) and Seal (10d) and Fitting (10e).

1. Install hose (9) into back of nozzle (3). Wrench tighten.
2. Install pipe swivel fitting (10b) into pump outlet. Wrench tighten.
3. Install fitting (10c) into swivel (10b). Wrench tighten.
Page 9 of the Graco 24F531 user manual — Flushing
Page 9 · click to enlarge
Page 9
Drum Mounting Bracket (2)Model 24F947 or 24M499

Operation

Drum mounted DEF System Models 24F947 or 24M499 include a Mounting Bracket Kit containing the following parts - Screws (2a), Screws (2b), Washers (2d), Hex Nuts (2e), Mounting Plate (2f), Nozzle Bath Holder (2g), Nozzle Holder Bracket (2h) and screws (2j). The Mount- ing Bracket and Nozzle Holder are also identified as item M on the Typical Installation Diagram provided on page 5.

Alpha letters included in the following instructions refer to letters shown in Typical Installation examples (FIG. 1 - FIG. 2, pages 4 - 5).

Priming

1. Hold dispensing nozzle (G) open while at the same time slowly opening the pump air regulator (D) until the pump (A) starts to cycle.
1. Assemble pump to bracket.
2. Allow the pump to cycle slowly until all the air has been pushed out of the lines and the pump is primed.
2. Position drum mounting plate (2f) on top of drum.
3. Use screws (2b), nuts (2e) and washers (2d) (provided) to install mounting plate to pump.
3. If the pump doesn’t prime crack the pump outlet fitting and slowly run the pump until you see fluid filling the pump.
4. Align holes in nozzle holder bracket (2h) with holes in plate (2f). Use screws (2b), nuts (2e) and washers (2d)(provided) to install meter tray plate.
4. Then tighten the connection.
5. Place nozzle bath tray (2g) in nozzle holder bracket (2h). Fill bath with water. Keep nozzle bath tray filled with water at all times.

NOTICE

To maintain the integrity and purity of the AUS32 (Aqueous Urea Solution 32.5%) and ensure proper operation of equipment:

Flushing

After initial assembly and installation, flush the entire dispensing system by pumping 5-10 gallons of DEF through it. This purges the system of air and insures any impurities that may have been in the system are washed out.

  • Once the system is assembled it must remain sealed to insure the integrity of the fluid. Breaking the seal on the system can lead to fluid contamination.
  • After dispensing DEF, drain all the fluid from the nozzle, making sure it is pointing downward when stored in the nozzle holder. DEF remaining in the nozzle tip and exposed to air will crystallize and can plug the nozzle.

Dispose of the DEF used to flush the system using approved DEF handling procedures. Do not return the fluid to the drum or tote or use it in a vehicle.

  • DO NOT lay the dispensing nozzle on the ground or on any surface that may contaminate the nozzle tip and compromise the purity of the DEF.

Operation

Page 10 of the Graco 24F531 user manual — Wall Mounted with Meter: Model 24F531 Wall Mounted without Meter: Model 24F878
Page 10 · click to enlarge
Page 10

Parts

Wall Mounted with Meter: Model 24F531 Wall Mounted without Meter: Model 24F878

Ref Part No. Description Qty

Ref Part No. Description Qty 1 24G745 PUMP, diaphragm, 515, plastic, bsp

8 124581 HOSE, cpld, 6', 3/4bspp x cut 1 9 124603 HOSE, 20', 3/4 bspp x 3/4 bspp 1 10 24H293 KIT, meter, auto nozzle (model 24F531 only) 1

2 24F870 KIT, pump bracket, 3 in 1 (See Kits, page 12)

10a 24G738 METER, flow 1 10b† 124964 SWIVEL, pipe, 3/4 x 3/4 bspp 1 10c† 24H292 FITTING, nipple, 3/4 x 1/2 bspp 1 10d† 124965 SEAL, elastomeric, 1/2 bspp 1 10e† 16G760 FITTING, adapter, 3/4 (f) x 1/2 (m) bspp

3 24F529 NOZZLE, w/swivel (model 24F878) 1

4 110147 REGULATOR, air, 1/4”npt & gauge (not shown)

5 110223 VALVE, vented 2 way (not shown)

11 103927 CLAMP, hose (not shown) 2 12 124963 VALVE, safety, air, 50 psi, 1/8 npt (not shown)

6 24F532 KIT, suction 1 6a† 124548 COUPLER, quick connect 1 6b† 124549 INSERT 1 6c† 124550 TUBE, down, 47 inch (119.4 cm) 1 7 156971 FITTING, nipple, short (not shown)

† Parts are included in kit or may be purchased sepa-

rately.

Graco 24F531 — Wall Mounted with Meter: Model 24F531 Wall Mounted without Meter: Model 24F878 diagram (page 10)
Fig. 10 · Wall Mounted with Meter: Model 24F531 Wall Mounted w…

Parts

Page 11 of the Graco 24F531 user manual — Drum Mounted without Meter: Model 24F947 Drum Mounted with Meter: Model 24M499
Page 11 · click to enlarge
Page 11

Drum Mounted without Meter: Model 24F947 Drum Mounted with Meter: Model 24M499

Ref Part No. Description Qty

Ref Part No. Description Qty 1 24G745 PUMP, diaphragm, 515,plastic, bsp 1 2 24F679 KIT, pump bracket, drum mount (See Kits, page 12)

10 24H293 KIT, meter, auto nozzle (model 24M499 only) 1

10a 24G738 METER, flow 1 10b† 124964 SWIVEL, pipe, 3/4 x 3/4 bspp 1 10c† 24H292 FITTING, nipple, 3/4 x 1/2 bspp 1 10d† 124965 SEAL, elastomeric, 1/2 bspp 1 10e† 16G760 FITTING, adapter, 3/4 (f) x 1/2 (m) bspp

3a 125078 NOZZLE, manual (model 24F947) 1 3b 24F529 NOZZLE, w/swivel (model 24F499) 4 110147 REGULATOR, air,1/4”npt & gauge (not shown)

5 110223 VALVE, vented 2 way (not shown) 1 6 24F532 KIT, suction (See Kits, page 12) 1 6a† 124548 COUPLER, quick connect 1 6b† 124549 INSERT 1 6c† 124550 TUBE, down 1 8 124875 HOSE, 2', 3/4 bsp x cut, inlet 1 9a 125079 HOSE, 12”, 3/4 bspp x cut end (model 24F947)

11 103927 CLAMP, hose (not shown) 2 12 124963 VALVE, safety, air, 50 psi,1/8 npt (not shown)

14 15T366 BOOT, swivel 3/4 black 1

† Parts are included in kit or may be purchased sepa-

rately.

9b 124671 HOSE, 12', 3/4 bspp x 3/4 bspp (model 24M499)

Graco 24F531 — Drum Mounted without Meter: Model 24F947 Drum Mounted with Meter: Model 24M499 diagram (page 11)
Fig. 11 · Drum Mounted without Meter: Model 24F947 Drum Mounte…

Parts

Page 12 of the Graco 24F531 user manual — Technical Data
Page 12 · click to enlarge
Page 12

Bracket (2) Kits

2. Bracket 24F870: Models 24F531 / 24F878 2 - Bracket 24F679: Model 24F947 / 24M499

2a SCREW, cap, hex head (not shown) 4 2b SCREW, cap, hex head 4 2c WASHER (not shown) 4 2d WASHER, plain 14 2e NUT, hex 7 2f PLATE, pump mount 1 2g HOLDER, nozzle bath 1 2h BRACKET, nozzle holder 1 2j SCREW, HH, 1/4 x 20 x 0.75” (not shown)

2a SCREW, cap, hex head 4 2b SCREW, thumb, 1/4-20 x 2” 2 2d WASHER, plain 12 2e NUT, hex 6 2f PLATE, pump mount 1 2g HOLDER, nozzle bath 1 2h BRACKET, nozzle holder 1 2j SCREW, HH, 1/4 x 20 x 0.75” (not shown)

Technical Data

PumpUSMetric Maximum fluid working pressure50 psi0.3 MPA, 3.4 bar Air pressure operating range30 to 50 psi0.2 to 0.3 MPA, 2.1 to 3.4 bar Operating temperature (based on mechanical stress only and may be altered significantly by pumping certain chemicals. Consult engineering guides for chemical compatibilities and temperature limits or contact your Graco distributor. Minimum40°F4.4°C Maximum88°F31.0°C Maximum air consumption28 scfm0.672 cubic meters/min. Maximum free flow delivery6.5 gpm25 lpm Maximum pump speed163 cpm Gallons (Liters) per cycle0.04 gallons0.15 liters Sound power level (measured per ISO standard 9614-2) At 70 psig (0.48 MPa, 4.8 bar) at 50 cycles per minute77 dBa At 100 psig (0.7 MPa, 4 bar) at maximum cycles per minute95 dBa Sound pressure level (measured 1 meter from pump) At 70 psig (0.48 MPa, 4.8 bar) at 50 cycles per minute67 dBa At 100 psig (0.7 MPa, 4 bar) at maximum cycles per minute85 dBa Air inlet size1/4 npt(f) Air exhaust port size3/8 npt(f) Fluid inlet size1/2 and 3/4 in. bspp (f) Fluid outlet size1/2 and 3/4 in. bspp (f) Wetted parts (in addition to ball, seat and diaphragm materials)polypropylene, PTFE, fluoroelastomer, SST Pump Weight (approximate)6.5 lbs2.9 kg System Weight (approximate)35 lbs15.8 kg

Technical Data

Page 13 of the Graco 24F531 user manual — Meter US Metric
Page 13 · click to enlarge
Page 13

Meter US Metric

Flow range 0.5 to 15 gpm 1.9 to 57 lpm

Maximum working pressure 50 psi 0.3 MPa, 3.4 bar

Minimum working pressure 5 psi 34 MPa, 0.3 bar

Weight 1.8 lb 0.82 kg

Unit of measurement (Display shows quantity in 0.01 increments up to 999.99 gallons, quarts, pints or liters. Totalizes in gallons or liters up to 99,999 units.)

Accuracy (At 2.5 gpm (9.5 lpm) at 70°F (21°C), with water and 1 gallon dispensed. May require calibration; out-of-box accuracy is +/- 5%)

+/- 2.5% after calibration

Repeatability (At 2.5 gpm (9.5 lpm), at 70°F (21°C), with water and 1 gallon dispensed.)

+/- 0.15%

Inlet and outlet 1/2 bspp

Operating temperature range -4°F to 122°F -25°C to 50°C

Storage temperature range -13°F ti 122°F -25°C to 50°C

Wetted parts SST, nickel, fluoroelastomer

Batteries (R ecommended batteriesDuracell ® , Energizer ® , Eveready ® , EN22 ® )

Duracell® is a registered trademark of Duracell Inc.

Eveready® and Energizer® are registered trademarks of Eveready Battery Co., Inc.

Technical Data · Factory-set in quarts · 2 AA Alkaline

Page 14 of the Graco 24F531 user manual — GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Page 14 · click to enlarge
Page 14

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM3A1189

For patent information, see www.graco.com/patents

Graco HeadquartersMinneapolis International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

Copyright 2011, Graco Inc. is registered to ISO 9001

www.graco.com February 2011, revised June 2014

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Graco 24F531

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Graco 24F531

Be the first to ask — other owners or our team will answer.

Original document

Graco 24F531 manual PDF

14 pages·1.3 MB·Automobile Parts·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…