EN
Graco logo
Official user manual

Graco 255278

10 pages·490 KB·Marine Radio·PDF·ENDEFRITNLJA
Graco 255278
Table of Contents 13 sections Related Manuals · Warnings · Overview · Setup · … ShowHide
Page 1 of the Graco 255278 user manual — Part No. 255278 Complete high flow severe duty shutoff check valve assembly
Page 1 · click to enlarge
Page 1

Instructions-Parts High Flow Severe Duty Shutoff Check Valve

For recirculation valves, shutoff check valves, or outlet shutoff check valves on XM plural-component sprayers.

Part No. 255278 Complete high flow severe duty shutoff check valve assembly

7250 psi (50 MPa, 500 bar) Maximum Working Pressure 160°F (71°C) Maximum Fluid Temperature

Page 2 of the Graco 255278 user manual — Component Manuals in U.S. English :
Page 2 · click to enlarge
Page 2

Contents

Related Manuals 2 Warnings 3 Overview 4 Setup 6 Repair 6 Parts 7 Troubleshooting 8 Repair Kit 8 Accessories 8 Technical Data 9 Mounting Dimensions 9 Graco Standard Warranty 10 Graco Information 10

Related Manuals

Component Manuals in U.S. English :

ManualDescription 312359XM Operation 313289XM Repair 313292XM OEM, Instructions-Parts 313342Dosing Valve, Instructions-Parts 312749XM Mix Manifold Kits Instructions-Parts

Related Manuals

Page 3 of the Graco 255278 user manual — WARNING WARNING WARNING WARNING
Page 3 · click to enlarge
Page 3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

  • FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:
  • Use equipment only in well ventilated area.
  • Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).
  • Keep work area free of debris, including solvent, rags and gasoline.
  • Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.
  • Ground all equipment in the work area. See Grounding instructions.
  • Use only grounded hoses.
  • Hold gun firmly to side of grounded pail when triggering into pail.
  • If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.
  • Keep a working fire extinguisher in the work area.
  • PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury.
  • Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.
  • Tighten all fluid connections before operating the equipment.
  • Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
  • TOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.
  • Read MSDS’s to know the specific hazards of the fluids you are using.
  • Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
  • Always wear impervious gloves when spraying or cleaning equipment.
  • PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:
  • Protective eyewear
  • Clothing and respirator as recommended by the fluid and solvent manufacturer
  • Gloves
  • Hearing protection
Page 4 of the Graco 255278 user manual — NOTE:
Page 4 · click to enlarge
Page 4

Overview

The high flow severe duty shutoff check valve is a valve that acts as a spring loaded one-way check valve when the valve is in the open position. When the handle is turned to the closed position, the ball is held against the seat closing flow in either direction. The valve can be manifold mounted with four screws and an o-ring face seal on the inlet, or it can be plumbed in place with 1/2 in. npt (f) threads on the inlet and two outlets.

NOTE:

It is recommended that this valve be used in the fully open and fully closed positions. To control the flow rate on a circulation line, use adjustable restriction valve 222200. See Accessories on page 8.

F IG . 1Cutaway View

Overview · Flow Direction · Flow Direction

Page 5 of the Graco 255278 user manual — Overview
Page 5 · click to enlarge
Page 5

Overview

Page 6 of the Graco 255278 user manual — NOTE:
Page 6 · click to enlarge
Page 6

Setup

7. Clean and inspect parts for wear and damage. Replace damaged parts from repair kit 256239.

Reference parts illustration on page 7.

Assemble

1. Mount the valve in place with two outlet ports pointed in the desired direction using o-ring (14) and four screws (11).

Reference parts illustration on page 7.

1. Install o-ring (9) in groove of check valve housing (10).
2. Plug the un-used outlet port with plug (15). Use thread tape or sealant on the npt threads.
3. Use handle (12) to close the valve stem (8) clockwise. Position handle (12) to point in the direction you want to show as “closed”.
4. Secure handle (12) in place on stem (8) with crown nut (11).
2. Start to thread stem (8) by hand into bottom of cartridge (10). Place handle (12) on stem (8) and turn counter-clockwise to fully thread stem (8) through top of cartridge (10) to full open position.

Repair

3. Insert spacer (7). Use plastic tool (110) and hammer (not provided) to install seal (6) with lips facing away from spacer (7) on to stem (8) until it stops against spacer (7).
4. Place cartridge (10) in vice with bottom facing upward. Place spring (5) and ball (4) on stem (8). Firmly press seal (2) over lip of cartridge until it snaps into place and holds all the parts in place.

Disassemble

Reference parts illustration on page 7.

5. Apply blue thread lock, from repair kit 256239, on cartridge (10) external threads and insert cartridge assembly into check valve housing (1).
1. Relieve upstream and downstream pressure. See operation manual 312359 for Pressure Relief Procedure . Leave stem (8) in open position.
6. Place housing (1) in vice and torque to 125 ft-lbs.
2. Clamp housing (1) in a vice. Remove nut (13) and handle (12) from top check valve housing (10).
7. Mount valve and position handle as described in Setup .
3. Remove cartridge assembly (10) from housing (1).
4. Remove ball (4), and spring (5).
5. Use plastic tool (110) provided in repair kit 256239 to remove seat (3) and seal (2).

NOTE:

If valve housing (10) is still mounted on a machine, use a 90° hex key to grab under seat (3) and remove from housing (1).

6. Place handle (12) upside down on stem (8). Turn clockwise and remove stem (8) from cartridge (10). The seal (6) and spacer (7) will come out with the stem. Remove seal (6) and spacer (7) from stem (8).

Setup

Page 7 of the Graco 255278 user manual — Parts
Page 7 · click to enlarge
Page 7

Parts

255278, Complete Shutoff Check Valve Shown

Graco 255278 — Parts diagram (page 7)
Fig. 1 · Parts

Ref. Part Description Qty. 1 15J594 HOUSING, check valve 1 2*◆ 15K692 SEAL, retainer, acetal 1 3* 15A968 SEAT, footvalve, carbide 1 4* 116166 BALL, carbide 1 5* 15M530 SPRING 1 6*◆ 15M529 SEAL, u-cup; UHMWPE 1 7* 15M189 SPACER, backup, seal 1 8* 15K347 STEM 1 9*◆ 121138 O-RING; PTFE 1 10* 15K199 HOUSING, top, check valve 1 11 121295 SCREW, cap, shcs; 5/16-18 x 2.5 in.

12 15R381 HANDLE, black 1 13 117623 NUT, cap (3/8-16) 1 14 121139 O-RING; PTFE 1 15 100361 PLUG, pipe; 1/2 npt 1

* Included in shutoff check valve cartridge 255747.

◆Included in shutoff check valve repair kit 256239

(purchase separately). See page 8 for parts included in kit.

Parts

Page 8 of the Graco 255278 user manual — 222200, Restriction Valve
Page 8 · click to enlarge
Page 8

Troubleshooting

ProblemCauseSolution Handle is hard to turn under pressure.Cartridge (10) is not tightened completely into housing (1).Torque cartridge (10) to 125 ft-lbs. (170 N•m).

Repair Kit

Accessories

256239, Shutoff Check Valve Repair Kit

Handles

See parts illustration on page 7.

Part Description Qty. 247789 HANDLE, blue 1 15R380 HANDLE, green 1 247788 HANDLE, red 1

Ref Part Description Qty. 2 15K692 SEAL, retainer, carbide 1 6 15M529 SEAL 1 9 121138 O-RING 1 110† 15T630 TOOL, u-cup and manifold 1 111† 113500 ADHESIVE, anaerobic 1

15R529, Fluid Inlet Block

Used on XM outlet to mount high flow severe duty shut-off check valve when mix manifold is remote. See manual 312749 for parts.

† Not shown.

256980, XM Remote Mix Manifold Conversion Kit

See manual 312749.

222200, Restriction Valve

Used to control flow rate in circulation lines. See manual 307892.

Troubleshooting

Page 9 of the Graco 255278 user manual — Mounting Dimensions
Page 9 · click to enlarge
Page 9

Technical Data

Maximum Fluid Working Pressure 7250 psi (50 MPa, 500 bar) Maximum Fluid Temperature 160°F (71°C) Check Valve Housing Fluid Ports 1/2 in. npt Wetted Parts carbide ball, carbide seat, sst stem, nickel plated steel,

PTFE o-rings, UHMWPE u-cup, acetal end cup seal. Full turns from closed to open position 1.5 turns

Loctite® is a registered trademark of the Loctite Corporation.

Mounting Dimensions

Graco 255278 — Mounting Dimensions diagram (page 9)
Fig. 2 · Mounting Dimensions

For manifold mounting this valve, the o-ring face groove must be duplicated on the mating surface.

Technical Data

Page 10 of the Graco 255278 user manual — GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Page 10 · click to enlarge
Page 10

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

This manual contains English. MM 313343

Graco HeadquartersMinneapolis International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

Copyright 2009, Graco Inc. is registered to ISO 9001

www.graco.com

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Handle is hard to turn under pres- sure.Cartridge (10) is not tightened com- pletely into housing (1).Torque cartridge (10) to 125 ft-lbs. (170 N•m). p.8

Ask about the Graco 255278

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Graco 255278

Be the first to ask — other owners or our team will answer.

Original document

Graco 255278 manual PDF

10 pages·490 KB·Marine Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…