EN
Graco logo
Official user manual

Graco 313704E

2 pages·240 KB·Automobile Parts·PDF·ENDEFRITNLJA
Graco 313704E
Table of Contents 1 sections Parts ShowHide
Page 1 of the Graco 313704E user manual — Part No.: 24A918 3500 psi (24 MPa, 241 bar) Maximum Working Pressure
Page 1 · click to enlarge
Page 1

Instructions

GL-11 ® Injector 313704E

EN

For Single-Line Parallel Automatic Lubrication Systems. For professional use only.

Part No.: 24A918 3500 psi (24 MPa, 241 bar) Maximum Working Pressure

PRESSURE RELIEF PROCEDURE Follow this procedure any time you are instructed to Relieve the Pressure; shut off the pump; clean or ser- vice any part of the system; or install or clean dispens- ing devices.

Graco 313704E — Part No.: 24A918 3500 psi (24 MPa, 241 bar) Maximum Working Pressure diagram (page 1)
Fig. 1 · Part No.: 24A918 3500 psi (24 MPa, 241 bar) Maximum…
1. Disconnect power.
2. Disable air supply to pump by either:
  • Closing bleed-type air valve OR
  • Disconnecting quick disconnect air coupler on vent valve.
  • SKIN INJECTION HAZARD High-pressure fluid from gun or dispense valve, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
  • Do not point gun or dispense valve at anyone or at any part of the body.
  • Do not put your hand over the dispense outlet.
  • Do not stop or deflect leaks with your hand, body, glove, or rag.
  • Follow Pressure Relief Procedure , when you stop dispensing and before cleaning, checking, or servicing equipment.

2-27/32” (72.2 mm) 2-3/16” (55.6 mm)

Page 2 of the Graco 313704E user manual — Technical Data
Page 2 · click to enlarge
Page 2

Parts

Ref. No. Part No. Description Qty. 1 15W653 HOUSING, injector 1 2 15W647 ADJUSTER, adapter 1 3 15W646 SCREW, adjusting 1 4 555303 NUT, jam, st 1/2-20 1 6* 122240 RING, sealing, valve 1 7* 122292 O-RING, inlet/outlet/adapter 2 8 24A916 PISTON, assembly 1 10* 122291 O-RING, piston 1 11* 122290 SPRING, injector 1 12 122293 SPACER, valve 1 13* 24B304 VALVE, honed 2 14* 122289 O-RING, valve body 2 15* 122288 RING, backup, piston 1 16 15W654 ADAPTER, inlet, injector 1 17 114916 KIT, fitting and cap, zerk 1

Graco 313704E — Parts diagram (page 2)
Fig. 2 · Parts

*Overhaul Kit 24B359 includes these parts.

Kits

24B359 KIT, overhaul, includes 5, 6, 7, 10, 11, 13, 14, 15 1 114916 KIT, fitting and cap, zerk 1

GL-11 Volume Adjustment Table DescriptionNumber of TurnsVolume in.3cc Maximum Adjustment †00.5008.19 360° Clockwise Turn10.4687.67 360° Clockwise Turn20.4357.13 360° Clockwise Turn30.4036.60 360° Clockwise Turn40.3716.08 360° Clockwise Turn50.3395.56 360° Clockwise Turn60.3075.03 360° Clockwise Turn70.2754.51 360° Clockwise Turn80.2433.98 360° Clockwise Turn90.2113.46 360° Clockwise Turn100.1782.92 360° Clockwise Turn110.1462.39 360° Clockwise Turn120.1141.87 360° Clockwise Turn130.0821.34 Minimum Adjustment140.0500.82
Graco 313704E — Kits diagram (page 2)
Fig. 3 · Kits

Technical Data

Maximum Working Pressure 3500 psi (24 MPa, 241 bar) Minimum Operating Pressure 1000 psi (6.9 MPa, 69 bar) Suggested Operating Pressure 2500 psi (17 MPa, 172 bar) Reset Pressure 600 psi (4.1 MPa, 41 bar) Output Volume Per Cycle †Adjustable: 0.050 to 0.500 in.3

Wetted Parts Carbon steel, Stainless steel, Copper, Fluoroelastomer Recommended fluids Lubricant: NLGI 000 - NLGI #2 Inlet 1/2” - 14 npt Outlet 1/4” - 18 npsf Outlet 1/8” - 27 npsf † Maximum adjustment setting is when adjusting screw (3) is just

making contact with indicator pin (8) with no inlet pressure. Turn adjusting screw clockwise (in), to reduce output. To adjust, loosen lock nut (4) and turn adjusting screw (3) the number of turns indicated on the GL-11 Volume Adjustment Table to obtain the desired volume. Tighten lock nut (4) when desired volume setting is reached.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 313704

Graco HeadquartersMinneapolis International Offices: Belgium, China, Japan, Korea
  • GRACO INC. AND SUBSIDIARIES
  • P.O. BOX 1441
  • MINNEAPOLIS MN 55440-1441
  • USA

Copyright 2009, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com Revised 11/2011

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Graco 313704E

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Graco 313704E

Be the first to ask — other owners or our team will answer.

Original document

Graco 313704E manual PDF

2 pages·240 KB·Automobile Parts·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…