EN
American Standard logo
Official user manual

American Standard 6932 SERIES

2 pages·113 KB·Indoor Furnishings·PDF·ENDEFRITNLJA
American Standard 6932 SERIES
Table of Contents 47 sections 6500 SERIES 6501 SERIES 6502 SERIES 6900 SERIES 6901 SERIES 6902 SERIES · 6530 SERIES 6531 SERIES 6532 SERIES 6930 SERIES 6931 SERIES 6932 SERIES · CAUTION VALVE INSTALLATION · RUBBER · … ShowHide
Page 1 of the American Standard 6932 SERIES user manual — 6500 SERIES 6501 SERIES 6502 SERIES 6900 SERIES 6901 SERIES 6902 SERIES
Page 1 · click to enlarge
Page 1
American Standard 6932 SERIES — 6500 SERIES 6501 SERIES 6502 SERIES 6900 SERIES 6901 SERIES 6902 SERIES diagram (page 1)
Fig. 1

6500 SERIES 6501 SERIES 6502 SERIES 6900 SERIES 6901 SERIES 6902 SERIES

6530 SERIES 6531 SERIES 6532 SERIES 6930 SERIES 6931 SERIES 6932 SERIES

Certified to comply with ANSI A112.18.1M US PATENT D371956

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

P r i n t e d i n M e x i c o

Page 2 of the American Standard 6932 SERIES user manual — 60186B
Page 2 · click to enlarge
Page 2

CAUTION VALVE INSTALLATION

Turn off hot and cold water

supplies before beginning.

RUBBER

Place RUBBER RING into ESCUTCHEON and screw ESCUTCHEON onto VALVE BODY until snug against internal stop.

ESCUTCHEON

GASKET

SPOUT OR BASE ASSEMBLY

RUBBER RING

Insert BASE or SPOUT shank through center hole of SINK, making sure RUBBER GASKET is properly positioned.

SPOUT

Tighten LOCKNUT to secure VALVE position. Attach COUPLING to TEE and tighten.

5/16'' MIN.

Assemble RUBBER WASHER, RETAINER, and LOCKNUT onto threads of SPOUT from underside of SINK.

LEDGE

Slide RUBBER FERRULE, FRICTION RING, and COUPLING NUT to outlet of VALVE and tighten COUPLING NUT firmly. Repeat on other VALVE.

RUBBER WASHER BRASS WASHER

Insert LIFT ROD through SPOUT (or BASE) and slot of RETAINER.

SINK

RUBBER WASHER

RETAINER

Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector.

LOCKNUT

Align SPOUT and tighten LOCKNUT. Be sure slot in BRASS WASHER is positioned to the rear as shown.

VALVE BODY

LOCKNUT

SINK 3 VALVE INSTALLATION (continued)

FLANGE

DRAIN ASSEMBLY (Models 6502, 6902, 6532 and 6932)

PUTTY

Prepare TUBE and TEE ASSEMBLY to fit available VALVE location. If necessary, cut and/or bend TUBING carefully. Make sure tube bend is close to the TEE so that it will not effect the compression joint at the VALVE.

SHANK

O-RING Apply a bead of PUTTY around underside of DRAIN PLUG flange. Insert DRAIN PLUG into SINK drain hole.

DRAIN

PLUG

TEE

O-RING

Hold DRAIN PLUG to prevent turning and assemble GASKET, WASHER, and LOCKNUT, from underneath sink.

RUBBER

Remove COUPLING NUT, FRICTION RING, and RUBBER FERRULE from each valve and slide onto tubing.

GASKET

SCREW

WASHER

Push TUBING ends into VALVE side outlets. Insert VALVES into mounting holes from underside of SINK.

Insert threaded end of TAILPIECE into lower end of DRAIN PLUG. Connect other end to trap.

LOCKNUT

Press TEE onto SHANK of SPOUT making certain that the SHANK O-RING is properly seated on SHANK.

TAIL PIECE

Position EXTENSION ROD onto POP-UP ROD and tighten THUMBSCREW.

DRAIN INSTALLATION

STOPPER

(Models 6801 and 6831 only)

Remove one end of CLIP from PIVOT ROD by squeezing ends together while sliding.

Push TAILPIECE down into TRAP (threaded end up).

FLANGE

Insert PIVOT ROD into second or third hole in EXTENSION and reassemble CLIP. (EXTENSION may need to be bent.)

Thread LOCKNUT, WASHER and GASKET onto DRAIN BODY.

SINK

PUTTY

Apply a bead of PUTTY to underside of FLANGE.

THUMBSCREW

POP-UP ROD

GASKET PIVOT

EXTENSION ROD

Feed DRAIN BODY up through SINK and thread FLANGE fully onto BODY.

WASHER

ROD

CLIP

LOCKNUT

Tighten LOCKNUT firmly, keeping the PIVOT ROD pointed towards the back of the SINK.

CLIP

TAILPIECE

PIVOT

DRAIN

ROD

BODY

Drop STOPPER into DRAIN BODY.

Pull TAILPIECE up and thread tightly into DRAIN BODY.

TAILPIECE

Adjust STOPPER height by repositioning EXTENSION and tightening THUMBSCREW.

TRAP

TEST INSTALLED FAUCET 5

Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks.

Remove AERATOR.

Operate LIFT ROD and check DRAIN for leaks.

With handle in OFF position, turn on water supplies and check all connections for leaks.

Turn handles into OFF position and replace AERATOR.

SERVICE 6

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°.

STOP WASHER

To change direction of handle rotation, proceed as follows:

SPRING

CLIP

Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then:

Turn valve to OFF position. Remove HANDLE and BONNET NUT. Remove SPRING CLIP. Lift STOP WASHER, turn 90° and replace. Replace SPRING CLIP. Replace BONNET NUT, HANDLE, SCREW, and INDEX.

Remove HANDLE and BONNET NUT. Remove CARTRIDGE by pulling up. Thoroughly rinse plastic SCREEN at base of CARTRIDGE.

CARTRIDGE

Replace CARTRIDGE until flange is tight against valve body. Turn valves OFF. Replace BONNET NUT, HANDLE, SCREW and INDEX.

AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.

SCREEN

HOTLINE FOR HELP

For toll-free information and answers to your questions, call:

Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

60186B

A m e r i c a n S t a n d a r d I n c . 1 9 9 7 C

90° · 1 (800) 223-0068

Ask about the American Standard 6932 SERIES

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the American Standard 6932 SERIES

Be the first to ask — other owners or our team will answer.

Original document

American Standard 6932 SERIES manual PDF

2 pages·113 KB·Indoor Furnishings·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…