

DLA-RS25
PROJECTEUR D-ILA
For Customer use : Enter below the serial No. which is located on the side of the cabinet. Retain this information for future reference.
Pour utilisation par le client : Entrer ci-dessous le N° de série qui est situé sous le boîtier. Garder cette information comme référence pour le futur.
Instrucción para el cliente : Introduzca a continuación el nº de serie que aparece en la parte inferior lateral de la caja. Conserve esta información como referencia para uso ulterior.
0809TTH-AO-AO © 2009 Victor Company of Japan, Limited

Safety Precautions
MACHINE NOISE INFORMATION (Germany only) Changes Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator position is equal or less than 20 dB (A) according to ISO 7779.
This product has a High Intensity Discharge (HID) lamp that contains mercury. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities or for USA, the Electronic Industries Alliance: http://www.eiae.org
About the installation place Do not install the projector in a place that cannot support its weight securely. If the installation place is not sturdy enough, the projector could fall or overturn, possibly causing personal injury.
IMPORTANT SAFEGUARDS Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, use and service. Please read these Important Safeguards carefully before use. - All the safety and operating instructions should be read
before the product is operated. - The safety and operating instructions should be retained
for future reference. - All warnings on the product and in the operating instructions
should be adhered to. - All operating instructions should be followed. - Place the projector near a wall outlet where the plug can
This projector is equipped with a 3-blade grounding type plug to satisfy FCC rule. If you are unable to insert the plug into the outlet, contact your electrician.
be easily unplugged. - Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. - Do not use attachments not recommended by the product
manufacturer as they may be hazardous. - Do not use this product near water. Do not use immediately
after moving from a low temperature to high temperature, as this causes condensation, which may result in fire, electric shock, or other hazards. - Do not place this product on an unstable cart, stand, or
table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. The product should be mounted according to the manufacturer’s instructions, and should use a mount recommended by the manufacturer. - When the product is used on a cart, care
PORTABLE CART WARNING (symbol provided by RETAC)
should be taken to avoid quick stops, excessive force, and uneven surfaces which may cause the product and cart to overturn, damaging equipment or causing possible injury to the operator. - Slots and openings in the cabinet are
provided for ventilation. These ensure reliable operation of the product and protect it from overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.)
1 Getting started


- To allow better heat dissipation, keep a clearance between
- Upon completion of any service or repairs to this product,
this unit and its surrounding as shown below. When this unit is enclosed in a space of dimensions as shown below, use an air-conditioner so that the internal and external temperatures are the same. Overheating can cause damage.
ask the service technician to perform safety checks to determine that the product is in proper operating condition. - The product should be placed more than one foot away
from heat sources such as radiators, heat registers, stoves, and other products (including amplifiers) that produce heat. - When connecting other products such as VCR’s, and DVD
150 mm and above

players, you should turn off the power of this product for protection against electric shock. - Do not place combustibles behind the cooling fan. For
300 mm and above
300 mm and above
example, cloth, paper, matches, aerosol cans or gas lighters that present special hazards when over heated. - Do not look into the projection lens while the illumination
lamp is turned on. Exposure of your eyes to the strong light can result in impaired eyesight. - Do not look into the inside of this unit through vents
200 mm and above
(ventilation holes), etc. Do not look at the illumination lamp directly by opening the cabinet while the illumination lamp is turned on. The illumination lamp also contains ultraviolet rays and the light is so powerful that your eyesight can be impaired. - Do not drop, hit, or damage the light-source lamp (lamp
power source indicated on the label. If you are not sure of
the type of power supply to your home, consult your product dealer or local power company. - This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug. - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the product. - For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power line surges. - Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can result in a risk of fire or electric shock. - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages and other hazards. Refer all service to qualified service personnel. - Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions: a) When the power supply cord or plug is damaged. b) If liquid has been spilled, or objects have fallen on the product. c) If the product has been exposed to rain or water. d) If the product does not operate normally by following the
unit) in any way. It may cause the light-source lamp to break and lead to injuries. Do not use a damaged light source lamp. If the light-source lamp is broken, ask your dealer to repair it. Fragments from a broken light-source lamp may cause injuries. - The light-source lamp used in this projector is a high
pressure mercury lamp. Be careful when disposing of the light-source lamp. If anything is unclear, please consult your dealer. - Do not ceiling-mount the projector to a place which tends
to vibrate; otherwise, the attaching fixture of the projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal injury. - Use only the accessory cord designed for this product to
prevent shock.
*DO NOT allow any unqualified person to install the unit. Be sure to ask your dealer to install the unit (e.g. attaching it to the ceiling) since special technical knowledge and skills are required for installation. If installation is performed by an unqualified person, it may cause personal injury or electrical shock.
operating instructions. Adjust only those controls that are covered by the Operation Manual, as an improper adjustment of controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. e) If the product has been dropped or damaged in any way. f) When the product exhibits a distinct change in performance - this indicates a need for service. - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

For USA and Canada only Use only the following power cord.
IMPORTANT (Europe only): The wires in the mains lead on this product are colored in accordance with the following cord: Green-and-yellow : Earth Blue : Neutral Brown : Live As these colors may not correspond with the colored making identifying the terminals in your plug, proceed as follows: The wire which is colored green-and-yellow must be connected to the terminal which is marked M with the letter E or the safety earth or colored green or green- and-yellow. The wire which is colored blue must be connected to the terminal which is marked with the letter N or colored black. The wire which is colored brown must be connected to the terminal which is marked with the letter L or colored red.
The power supply voltage rating of this product is AC110V – AC240V. Use only the power cord designated by our dealer to ensure Safety and EMC. Ensure that the power cable used for the projector is the correct type for the AC outlet in your country. Consult your product dealer.
(United Kingdom only)
For United Kingdom For European continent countries
HOW TO REPLACE THE FUSE: When replacing the fuse, be sure to use only a correctly rated approved type, re-fit the fuse cover.
WARNING: Do not cut off the main plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter or consult your dealer. If nonetheless the mains plug is cut off, dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the main supply. If a new main plug has to be fitted, then follow the instruction given below.
IF IN DOUBT —— CONSULT A COMPETENT ELECTRICIAN. Open the fuse compartment with the blade screwdriver, and replace the fuse. (* An example is shown in the illustration below.)
This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan, Limited is: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Germany

[European Union only] These symbols indicate that equipment with these symbols should not be disposed of as general household waste. If you want to dispose of the product or battery, please consider the collection systems or facilities for appropriate recycling.
contains lead.
Products
DEUTSCH
Benutzerinformationen zur Entsorgung alter Geräte und Batterien
[Nur Europäische Union] Diese Symbole zeigen an, dass derartig gekennzeichnete Geräte nicht als normaler Haushaltsabfall entsorgt werden dürfen. Wenden Sie sich zur Entsorgung des Produkts oder der Batterie an die hierfür vorgesehenen Sammelstellen oder Einrichtungen, damit eine fachgerechte Wiederverwertung möglich ist.
Blei enthält.
FRANÇAIS
Informations relatives à l’élimination des appareils et des piles usagés, à l’intention des utilisateurs
[Union européenne seulement] Si ces symboles figurent sur les produits, cela signifie qu’ils ne doivent pas être jetés comme déchets ménagers. Si vous voulez jeter ce produit ou cette pile, veuillez considérer le système de collection de déchets ou les centres de recyclage appropriés.
contient du plomb.
Produits
NEDERLANDS
Informatie voor gebruikers over het verwijderen van oude apparatuur en batterijen
[Alleen Europese Unie] Deze symbolen geven aan dat apparatuur met dit symbool niet mag worden weggegooid als algemeen huishoudelijk afval. Als u het product of de batterij wilt weggooien, kunt u inzamelsystemen of faciliteiten voor een geschikte recycling gebruiken.
bevat.

Información para los usuarios sobre la eliminación de baterías/pilas usadas
[Sólo Unión Europea] Estos símbolos indican que el equipo con estos símbolos no debe desecharse con la basura doméstica. Si desea desechar el producto o batería/pila, acuda a los sistemas o centros de recogida para que los reciclen debidamente.
plomo.
Productos
ITALIANO
Informazioni per gli utenti sullo smaltimento delle apparecchiature e batterie obsolete
[Solo per l’Unione Europea] Questi simboli indicano che le apparecchiature a cui sono relativi non devono essere smaltite tra i rifiuti domestici generici. Se si desidera smaltire questo prodotto o questa batteria, prendere in considerazione i sistemi o le strutture di raccolta appropriati per il riciclaggio corretto.
Prodotti
PORTUGUÊS
Informação para os utilizadores acerca da eliminação de equipamento usado e pilhas
[Apenas União Europeia] Estes símbolos indicam que o equipamento com estes símbolos não deve ser eliminado juntamente com o restante lixo doméstico. Se pretende eliminar o produto ou a pilha, utilize os sistemas de recolha ou instalações para uma reciclagem apropriada.
Produtos
ΕΛΛΗΝΙΚΑ
Πληροφορίες για την απόρριψη παλαιού εξοπλισμού και μπαταριών
[ Ευρωπαϊκή Ένωση μόνο ] Αυτά τα σύμβολα υποδηλώνουν ότι ο εξοπλισμός που τα φέρει δεν θα πρέπει να απορριφθεί ως κοινό οικιακό απόρριμμα . Εάν επιθυμείτε την απόρριψη αυτού του προϊόντος ή αυτής της μπαταρίας , χρησιμοποιήστε το σύστημα περισυλλογής ή εγκαταστάσεις για ανάλογη ανακύκλωση .
μπαταρία περιέχει μόλυβδο .
1 Getting started

Сведения для пользователей по утилизации старого оборудования и батарей
[только для Европейского союза] Данные символы указывают на то, что оборудование, на которое они нанесены, не должны утилизироваться, как обычные бытовые отходы. При необходимости утилизировать такое изделие или батарею обратитесь в специальный пункт сбора для их надлежащей переработки.
батарея содержит свинец.
ČESKY
Informace pro uživatele k likvid aci starého zařízení a baterií
[Pouze Evropská unie] Tyto symboly označují, že produkty s těmito symboly se nesmí likvidovat jako běžný odpad. Pokud chcete produkt nebo baterii zlikvidovat, využijte sběrný systém nebo jiné zařízení, které za jistí řádnou recyklaci.
Upozornění: Značka Pb pod symbolem pro bate rie znamená, že tato baterie obsahuje olovo.
Produkty
POLSKI
Informacje dla użytkowników dotyczące poz bywania się zużytego sprzętu i baterii
[Tylko kraje Unii Europejskiej] Te symbole oznaczają, że sprzętu nie należy wyrzucać razem z odpadami gospodarczymi. Jeśli trzeba po zbyć się tego produktu lub ba terii, proszę skorzystać z systemu odbioru lub urządzeń do zbiórki odpadów elektronicznych, w celu odpowiedniego ponowne go ich przetworzenia.
Produkty
MAGYAR
Felhasználói információ az elhasznált be rendezések és akkumulátorok elhelyezéséről
[Csak az Európai Unióban] Ez a szimbólum azt jelzi, hogy a berendezés nem helyezhető az általános háztartási hulladék közé. Ha meg szeretne szabadulni a terméktől vagy az akkumulátortól, akkor legyen tekintettel az gyűjtő rendszerre vagy intézményekre a megfelelő hasznosítás érdekében.
Megjegyzés: Az alábbi Pb szimbólum - ha az akkumulátoron megtalálható - azt jelzi, hogy az akkumulátor ólmot tartalmaz.
Termékek
1 Getting started

THX Certification
THX Certification THX Ltd. was founded by filmmaker George Lucas to improve the cinema and home entertainment experience through strict engineering standards and breakthrough technologies. THX has leveraged more than 25 years of filmmaking, cinema design and post-production expertise to partner with JVC to engineer a best-in-class home theater projector.
With a strict focus on image quality and signal processing performance, THX certification promises that this JVC projector is capable of presenting a wide range of video content at maximum resolutions with the correct color and luminance levels. In addition, THX has created a battery of signal processing tests that challenge the projector’s scaling, motion conversion and de-interlacing capabilities. This type of in-depth analysis predicts how the projector will present a variety of high definition and standard definition content.
The JVC projector also features THX Movie Mode, a pre-calibrated video setting for watching movies on DVD, Blu-ray HD or broadcast television. This playback feature is designed to recreate the cinema experience at home by setting the display’s gamma, luminance, color temperature and other settings to mirror those used by filmmakers in post-production. THX Movie Mode also ensures projector brightness is optimal for large screen viewing.


For detail information about ISF, please refer web site http://www.imagingscience.com/




This manual mainly describes the operating method using the remote control.
Buttons to be used are colored in a darker shade.
Remote Control 1 piece
AAA size Batteries (for operation confirm) 2 pieces
Power Cord For the US market (2 m) 1 piece
Power Cord For the EU market (2 m) 1 piece
Power Cord For the UK market (2 m) 1 piece
Please check with your authorized dealer for details.



Remote Sensor ( P15)
1 Getting started · Lens Cover · (closed)


Light on (Red): Standby mode Light on (Green): During projection Blinking (Green): Image is temporarily hidden ( P25) Blinking (Red): Cool Down mode ( P25)
Feet: The height (0 to 5 mm) can be adjusted by turning the foot.
Manual button for lens cover: Press and hold the button to open the lens cover. As this is used for maintenance, it is not necessary to use it at normal times. ( P56)


To turn on the power To turn off the power
To select input mode ( P24)
To control lens ( P24)
To hide the image temporarily ( P25)
To set the screen size ( P26)
To display test pattern
To illuminate buttons on the remote control for 7 seconds
To select or confirm
To display/close the menu
To return to the previous menu BACK
To switch picture mode ( P42)
To set gamma ( P42)
To switche sequentially between Contrast, Brightness, Color, Tint, Sharpness and Detail enhance.
To adjust color temperature ( P42)
Lens Aperture ( P42)
1 Getting started

Loading Batteries

and operate the remote control.


This unit · Remote control



BD/DVD Recorder BD/DVD Player





To connect via component video terminals ( P17)
To connect RS-232C terminal (external control) ( P52)
To connect via Trigger terminal ( P20) To connect via PC terminal ( P20)
To connect via video terminal ( P17) To connect via S-video terminal ( P17)


PC VCR and camcorder
2 Preparation


Connecting via Video Cable and S-Video Cable



Connecting via HDMI Cable


2 Preparation



This unit · This unit


PC cable(sold separately) VGA output terminal

2 Preparation

While installing, please place this unit and the screen perpendicular to each other. Failing to do so may increase trapezoidal distortion. Please refer to “Keystone”. ( P39 - 25 )
* 0% up/down position (center)
Approximately 34% (maximum) of the projected image
Approximately 34% (maximum) of the projected image
* 0% left/right position (center)
Approximately 80% (maximum) of the projected image
Approximately 80% (maximum) of the projected image
Lens shift correlation chart:
Left-Right Shift(%) 0% 5% 10% 15% 20% 25% 30% 34%
Up-Down Shift(%) 80% 74% 66% 57% 47% 34% 18% 0%
maximum Left-Right shift varies with the amount of Up-Down shift. ● The values on the chart are intended to act as a guide. Use them for reference
during installation.

Screen Size and Projection Distance
Determine the distance from the lens to the screen to achieve your desired screen size. This unit uses a 2.0x power zoom lens for projection.
(Diagonal Length) Aspect Ratio 16:9
(Diagonal Length) Aspect Ratio 16:9
60" (Approx. 1.52m) Approx. 1.78m to Approx. 3.66m 140" (Approx. 3.56m) Approx. 4.23m to Approx. 8.60m
70" (Approx. 1.78m) Approx. 2.09m to Approx. 4.28m 150" (Approx. 3.81m) Approx. 4.53m to Approx. 9.22m
80" (Approx. 2.03m) Approx. 2.40m to Approx. 4.89m 160" (Approx. 4.06m) Approx. 4.84m to Approx. 9.84m
90" (Approx. 2.29m) Approx. 2.70m to Approx. 5.51m 170" (Approx. 4.32m) Approx. 5.14m to Approx. 10.45m
100" (Approx. 2.54m) Approx. 3.01m to Approx. 6.13m 180" (Approx. 4.57m) Approx. 5.45m to Approx. 11.07m
110" (Approx. 2.79m) Approx. 3.31m to Approx. 6.75m 190" (Approx. 4.83m) Approx. 5.75m to Approx. 11.68m
120" (Approx. 3.05m) Approx. 3.62m to Approx. 7.36m 200" (Approx. 5.08m) Approx. 6.06m to Approx. 12.30m
130" (Approx. 3.30m) Approx. 3.92m to Approx. 7.98m



This section describes the basic operations to project input images on the screen.

1 Connect to this unit 2 Connect to the power outlet
HDMI 1 HDMI 2 COMP. Video S-Video PC
4 Adjusts image focus, size (zoom), and position (shift). 1 Adjust the focus
3 Basic Operation · buttons


Adjust image position (shift).


Adjust accordingly by pressing the up/down
“Pixel Adjust” from the Settings menu “Installation”. ( P38 - 23 ) ● Every time the LENS button is pressed, the adjustment item will be switched among “Focus”, “Zoom” and “Shift”.
Focus Zoom Shift LENS
4 To end
5 Turn off the power
STAND BY
While a confirmation screen is displayed
of lamp life. ● During Cool Down mode, the [STANDBY/
ON] indicator blinks in red. ● After the Cool Down mode is complete,
Light on (Red Lamp)
after it has been turned on. Start operation only after 90 seconds
time. ● You can also press the button on the unit to turn off the
power. ( P13) ● Pull out the power plug when the unit will not be used for a
prolonged time.
buttons · Blinking (Red Lamp) · Cool Down mode

You can change the screen size of the projected image or hide the surrounding area of an image for which quality at the outer area has deteriorated.
The projected image can be set to a most appropriate screen size (aspect ratio).

( P37 - 16 ) ● When PC signals are input, the “Aspect(Computer)” setting will be available
instead. ( P37 - 17 ) ■ Input Image and Projected Image by Different Screen Size
Screen Size Input Image
SDTV (4:3) Aspect Ratio: Same Most appropriate screen size
SDTV(4:3) Image recorded in landscape (black bands on top and bottom) of DVD software
stretched image, while selecting “16:9” provides you with the most
appropriate screen size.
Images for which quality at the outer area has deteriorated can be projected by masking (hiding) the surrounding area of the projected image.

Image for which quality at the outer area has deteriorated.
3 Basic Operation


definition images are input.
Color Tint Color Temp. Gamma
Video/S-Video COMP.
Aspect(Video) Aspect(Computer)
16:9 Auto
2.5%
Mask Off 5% Off
Video/S-Video COMP.
16:9 Aspect(Video) Aspect(Computer) V-stretch
5% 2.5%
MENU BACK Back Select
Example:
When the “Mask” value is
changed from “Off” “5%”

CAUTION

01 Picture Mode Adjusts the pattern of the projected image.
02 Contrast Adjusts the contrast of the projected image.
03 Brightness Adjusts the brightness of the projected image.
04 Color Adjusts the color density of the projected image.
05 Tint Adjusts the hue of the projected image.
06 Color Temp. Sets the color temperature of the projected image.
07 Gamma Sets the gradation characteristics of the projected image.
08 Advanced Adjusts the contours of the image and detailed composition of the image.
11 HDMI Configures HDMI input signal.
12 COMP. Configures the input signal for the component video input terminals.
13 Video/S-Video Configures the Video/S-Video input signals.
14 PC Configures PC input.
15 Picture Position Adjusts the horizontal/vertical position of the projected image.
16 Aspect (Video) Configures the screen size of the projected image.
17 Aspect (Computer) Configures the screen size of the projected image.
18 V-Stretch When set to “On”, the projected 2.35:1 image will be stretched vertically to the panel resolution.
19 Over Scan Selects whether or not to set over scan for the SD video signal.
20 Mask Masks (Hides) the outer area of the projected image.
21 Film Mode Selects this to view movies shot on film. Setting: Auto, film, Off
4 Settings



22 Lens Control Controls the individual motorized function of the lens when setting up the projector.
23 Pixel Adjust Makes fine adjustments of 1 pixel unit for each minor color shift in the horizontal/vertical direction of the image.
24 Installation Style Flips the image to the left or right, up or down according to the projection state of the projector.
25 Keystone Compensates for trapezoidal distortion caused by installation.
26 Screen Adjust Corrects skewed white balance derived from the reflective characteristics of the screen.
27 Back Color Configures the screen color displayed when there is no input signal.
28 Menu Position Sets the display position of the menu. The possible positions for displaying the menu are at the four corners or at center of the screen.
29 Menu Display Sets the duration for displaying the menu.
30 Line Display Sets whether to display the input setting when switching the input. Setting: 5 sec, Off
31 Source Display Sets whether to display the source of input signals when changing the input.
32 Logo Sets whether to display “Logo” during startup. Setting: On, Off 33 Language Sets the language of the menu display (12 languages).

34 Lamp Power Configures the output of the light-source lamp.
36 Test Pattern Display 6 types of test patterns.
37 Off Timer Automatically powers off when there is no operation for a certain duration.
Selects this when using the projector in a location of low atmospheric pressure (higher than 900 meters above sea level). Setting: On, Off
Information Input Image Connector, Input Source Name, PC resolution, PC H Frequency, PC V Frequency, Deep Color Depth, and Lamp Use are displayed.

Projected images can be adjusted to a desired view by changing the initial settings.


When changing “Aspect(Video)” from “4:3” to “16:9”
4 Settings


Item values shown in are factory settings.
01 Picture Mode
Selects Picture Mode(Cinema 1, Cinema 2, Cinema 3, Natural, Stage, Dynamic, User 1, User 2 and THX).
Cinema 1 This is the picture setting closest to film. It is best suited for general movie viewing.
Cinema 2 This is the picture setting for vivid hues based on HDTV standards. It is best suited for viewing action movies and movies with vivid colors.
Cinema 3 This is the picture setting best suited for viewing animated movies.
Natural This is the picture setting for natural hues and tones. It is best suited for viewing dramas and video.
Stage This is the picture setting best suited for watching live concerts and stage performances.
Dynamic This is the picture setting best suited for viewing the picture in a room that cannot be made completely dark.
THX This is the picture setting certified by THX Ltd.
Adjusts the contrast of the projected image.
(Black) –50 to 50 (White)
Adjusts the brightness of the projected image.
(Darken) –50 to 50 (Brighten)
Adjusts the color density of the projected image.
(Lighten) –50 to 50 (Darken)
Adjusts the hue of the projected image.
(Red) –50 to 50 (Green)

Picture Adjust > Color Temp.
06 Color Temp.
Sets the color temperature of the projected image. (Cannot set when the “Picture Mode” in “THX”.)
5800K Select this to give a reddish tinge to the image.
Only offset can be set. 6500K Select this to have a balanced image.
7500K Select this to give a bluish tinge to the image.
9300K Select this to give a greater bluish tinge than 7500K.
High Bright Select this to get the brightest image.
Based on this selection of Correction Value (5800K, 6500K, 7500K, 9300K, H.B.), adjusts the following Gains and Offsets.
Red (Less red) –50 to 50 (More red)
Green (Less green) –50 to 50 (More green)
Blue (Less blue) –50 to 50 (More blue)
Red (Less red) –50 to 50 (More red)
Green (Less green) –50 to 50 (More green)
Blue (Less blue) –50 to 50 (More blue)
Based on this selection of Correction Value (5800K, 6500K, 7500K, 9300K, H.B.), adjusts the following Gains and Offsets.
Red (Less red) –50 to 50 (More red)
Green (Less green) –50 to 50 (More green)
Blue (Less blue) –50 to 50 (More blue)
Red (Less red) –50 to 50 (More red)
Green (Less green) –50 to 50 (More green)
Blue (Less blue) –50 to 50 (More blue)
Based on this selection of Correction Value (5800K, 6500K, 7500K, 9300K, H.B.), adjusts the following Gains and Offsets.
Red (Less red) –50 to 50 (More red)
Green (Less green) –50 to 50 (More green)
Blue (Less blue) –50 to 50 (More blue)
Red (Less red) –50 to 50 (More red)
Green (Less green) –50 to 50 (More green)
Blue (Less blue) –50 to 50 (More blue)

07 Gamma
Sets the gradation characteristics of the projected image. (Cannot set when the “Picture Mode” in “THX”.)
Normal For normal circumstances, select this setting. This is the setting for Standard Tones.
A Set gamma to “A”. This is the setting for expressing rich dark tones.
B Set gamma to “B”. This is the setting for the characteristic tonal qualities of film.
C Set gamma to “C”. This setting provides even richer darker tones than setting B.
D Set gamma to “D”. This setting provides brighter midtones.
Three different kinds of gamma can be set according to your preferences.
Value The coefficient (1.8 to 2.6) of the gamma curve can be selected.
The gamma curve for the colors (Red, Green, Blue) can be adjusted separately. Adjusting “White” will adjust for all “Red, Green, Blue” values. The gamma curve displays the value for “Green”.
Custom 1 Custom 2 Custom 3 (Gamma Setup)
Copy Copy the adjusted gamma data.
Paste Paste the copied gamma data.
Reset Return the gamma coefficients to the values 2.2 set by “Correction Value”.
* “Gamma Adjustment”
1 Select the reference gamma curve coefficient (1.8 ~ 2.6) in “Correction Value”.
2 Select the color to be adjusted in the gamma adjustment screen.
MENU BACK Back Select
3 Adjust the gamma curve in the gamma curve adjustment screen.
A B C D
MENU BACK Back Select Operate TEST Check Before Back
MENU BACK Back Select Operate TEST Check Back After
Select the point where the gradation (brightness) is to be adjusted with the / buttons.
Adjust the gradation (brightness) with the / buttons.


* Regarding “Copy” and “Paste”
1 Copies the Gamma Adjustment data.
MENU BACK Back Select Operate TEST Check Back After
Select copy using the / buttons.
2 Pastes the copied data.

OK
MENU BACK Back Select Operate TEST Check Back After
08 Advanced Adjusts the contours of the image, detailed composition of the image and image color. (Cannot set when the “Picture Mode”
in “THX”.)
Sharpness (Soft) 0 to 100 (Sharp) Adjusts the outline of image. Detail Enhancement (Soft) –50 to 50 (Strong) Emphasizes the details of image.
RNR (Soft) 0 to 16 (Strong) Adjusts the intensity of removing image noise.
MNR (Soft) 0 to 16 (Strong) Adjusts the intensity of removing mosquito noise.
BNR On Reduces block noise. Off Input signal remains unchanged.
Off Input signal remains unchanged. Low
Reduces color smear. (Color Contour Correction) Middle
* In case of HD signals or PC signals, NR and CTI cannot be set. ● Abbreviations NR: Noise Reduction RNR: Random Noise Reduction MNR: Mosquito Noise Reduction BNR: Block Noise Reduction CTI: Color Transient Improvement
Off The image color cannot be adjusted.
Pause Off Video mode On Still mode
Custom 1 Custom 2 Custom 3
Values of each color can be adjusted (“Red,
Yellow, Green, Cyan, Blue and Magenta”).
All Reset Return to the factory settings.
Improves fast-moving pictures to a clear image with little residual image. Low High
* With regard to “Clear Motion Drive”, it is not possible to set the PC signal. Furthermore, depending on the scene, the picture may be distorted. In this case, please select “off”.

* About “Color Management Adjustment”
1 Set the picture mode of the color management.
2 Select the color to be adjusted by color management. 3 Select color adjustment.
Off Custom1 Custom2 Custom3
Off Custom1 Custom2 Custom3
Pause Off Red Yellow Green
Cyan Blue Magenta All Reset
MENU BACK Back Select
MENU BACK Back Select
4 Select the “Hue”, “Saturation” or “Brightness” using the / button.
5 Use the / button to adjust.
brightness in each “Color Management” mode is not possible.


Standard Select this when the dynamic range of the input images is 16-235.
Enhanced Select this when the dynamic range of the input images is 0-255.
YCbCr(4:4:4) Select this when the Y Cb Cr(4:4:4) video signals are input.
YCbCr(4:2:2) Select this when the Y Cb Cr(4:2:2) video signals are input. RGB Select this when the RGB video signals are input.


Configures the input signal for the component video input terminals.
Y Pb/Cb Pr/Cr Select this when the component video signals are input.
RGB Select this when the RGB video signals are input.
SCART Select this when RGB video signals and sync signals are input via the SCART interface for European markets. ● The setting is available only if the component video terminals are selected.

0IRE Adjusts the gradation for signals without the 7.5 IRE setup.
7.5IRE Adjusts the gradation for signals with the 7.5 IRE setup.
NTSC Select this when the color system is NTSC.
NTSC4.43 Select this when the color system is NTSC4.43.
PAL Select this when the color system is PAL.
PAL-M Select this when the color system is PAL-M.
PAL-N Select this when the color system is PAL-N.
SECAM Select this when the color system is SECAM.

Auto Alignment Automatically adjusts “Tracking”, “Phase” and “Picture Position”.
Tracking Adjust the horizontal size and display area of the image. (This may vary depending on the signal, but does not usually require adjustment.)
Phase Adjust flickering and blurred images. (This may vary depending on the signal, but does not usually require adjustment.)
Picture Position Adjust the display position of the image.
Adjusts the horizontal/vertical position of the projected image. ● The position of the image varies depending on the input signals. The image of some signals may not be fully displayed. Adjust the position of image using this menu to display the image properly.
4 Settings · 15 Picture Position


4:3 Sets the screen size of the projected image as 4:3.
16:9 Sets the screen size of the projected image as 16:9.
Zoom Zooms the images. (This item cannot be selected in the case of HD signals.)

Auto Enlarges the PC signal horizontally/vertically until it fits the panel height, and displays it in the original aspect ratio.
1:1 Displays the PC signal corresponding to the panel at one dot per pixel ratio. The PC screen can be shown in the original size. Full Enlarges the PC signal horizontally/vertically.

When set to “On”, the projected 2.35:1 image will be stretched vertically to the panel resolution.
On The projected 2.35:1 image will be stretched vertically to the panel resolution.
Off Projects the 2.35:1 image as-is. (Black bands will be displayed on the top and bottom.)
“Off” “On”

Selects whether or not to set over scan for the SD video signal.
On Over scan the top, left, bottom and right at 2.5% each.


Masks (Hides) the outer area of the projected image.
Off No masking. ● Masking is available only when high definition images are input.

Auto After determining if the picture is 24 frame film or 60 frames (50 frames) video, changes the setting to the optimal progressive conversion.
Film Corrects unnatural movement of material pulldown processed from 24 frames to 60 frames (50 frames) and returned to 24 frames. Off Sets the appropriate progressive conversion for video.

Controls the individual motorized function of the lens when setting up the projector
Shift Function for adjusting lens shift. (Press the up/down/left/right button to shift the screen).
Displays the image pattern in conjunction with the above setting items.
Display Display for “Focus”: for “Zoom” and “Shift”:
(Picture of big green grids) (Picture of small green grids)
Off Without displaying the image pattern, displays the external input signal.
On Disables lens adjustment. A warning message appears when the [LENS] button on the remote control is pressed.

Makes fine adjustments of 1 pixel unit for each minor color shift in the horizontal/vertical direction of the image.
Horiz. Red (Move red to left) 1 to 7 (Move red to right)
Horiz. Green (Move green to left) 1 to 7 (Move green to right)
Horiz. Blue (Move blue to left) 1 to 7 (Move blue to right)
Vert. Red (Move red down) 1 to 5 (Move red up)
Vert. Green (Move green down) 1 to 5 (Moves green up)
Vert. Blue (Move blue down) 1 to 5 (Move blue up)
4 Settings


Flips the image to the left or right, up or down according to the projection state of the projector.
Ceiling Mount (F) Select this for ceiling front projection.
Ceiling Mount (R) Select this for ceiling rear projection.
Compensates for trapezoidal distortion caused by installation. ● If the “Shift Adjustment” is excepting 0%, the image may be projected on the screen incorrectly when trapezoidal distortion is compensated. ( P21)

Corrects skewed white balance derived from the reflective characteristics of the screen.

Configures the screen color displayed when there is no input signal.

28 Menu Position Sets the display position of the menu. The possible positions for displaying the menu are at the four corners or at center of the screen.

25 Keystone


Sets whether to display the input setting when switching the input.

Sets whether to display the source of input signals when changing the input.

Sets whether to display “Logo” during startup.


High Select this when it is difficult to see the image in a bright room. (200W)
4 Settings


Off Do not activate. On(Power) Move the screen UP/DOWN in conjunction with the power. On(V-Stretch) Operate the anamorphic lens in conjunction with the “V-Stretch”.

Display 6 types of test patterns. For checking the color condition and tone, and the pixel size. Use whenever necessary. ● This can also be displayed by the remote control. ( P14)

Automatically powers off when there is no operation for a certain duration.

Selects this when using the projector in a location of low atmospheric pressure (higher than 900 meters above sea level).
Input Displays the currently selected video input.
Source Displays the type of the current video input signal. (If PC signal is input, this item cannot be displayed) Resolution In the case of PC signal, the resolution is displayed.
H Frequency In the case of PC signal, the horizontal frequency is displayed.
V Frequency In the case of PC signal, the vertical frequency is displayed.
Deep Color Displays the bit depth (color depth) of the video signals input from the HDMI terminals. [Deep Color is not displayed when Y Cb Cr (4:2:2) is input.]
Lamp Time Displays the accumulated hours of usage of the light-source lamp.

You can adjust the projected image to a desired image quality and register the adjusted value. (Picture Mode) Besides the five default “Cinema 1”, “Cinema 2”, “Cinema 3”, “Natural”, “Stage”, “Dynamic” and “THX” settings, there are 2 more types of user-defined settings for Picture Mode.


“Contrast”, “Brightness”, “Color”, “Tint”, “Color Temp.”, “Gamma”, “Sharpness”, “NR”, “CTI”, “Lens aperture” and “Clear Motion Drive” are registered in the Picture Mode.
also be adjusted from the remote control. ( P14)
4 Settings


1 Adjust picture quality ● See “Changing the Initial Setting of Picture Mode” for procedures
on adjusting the picture quality. ( P42) 2 Display the setting menu
3 Select “Picture Adjust” “Picture Mode” “Natural”

Troubleshooting Before sending the unit to your authorized dealer for repair, please check the following points. The following situations are not malfunctions. ■ You do not need to worry about the following situations if there is no abnormality on the screen.
noise.
1 When the unit is in standby mode, please pull out the power plug, then insert again.
missing pixels or pixels that remain permanently lit up.

Is the power cord disconnected? Insert the power cord (plug) firmly. P24
Is the lamp cover properly shut? Remove the power plug when the unit is in standby mode and close the lamp cover properly. After that, insert the plug again. P49
Is the lamp in Cool Down mode? After the Cool Down mode is complete, turn on the power again. P25

Check the lamp time on the information menu. Prepare a new lamp unit or replace as soon as possible when the lamp is near exhaustion.

The unit works when power is turned on but stops abruptly after a few minutes
Remove the power plug when the unit is in standby mode and remove any blocking object. After that, insert the plug again. P12 to 13
Video image does not appear Is the correct external input selected? Select the correct external input. P24
Is the AV device properly connected? Connect the AV device properly. P16 to 20
Is the power of the AV device turned on? Turn on the power of the AV device and play the video. P24
Are the correct signals being output from the AV device? Set the AV device properly. P16 to 20
Is the setting of the input terminal correct?
P35 - P36 - Is the video image temporarily hidden? Press the [HIDE] button to display the video image again. P25
Set “COMP.” and “HDMI” in the setting menu according to the input signal.
Will the picture flicker and become invisible with HDMI input? Please use a short HDMI cable. P18
5 Troubleshooting


Is the setup of “Control with HDMI” function “Off”? Set up the “Control with HDMI” function to “Off”. P35 - 11
Is the image correctly adjusted? Adjust “Color” and “Tint” in the setting menu. P31 - 04 05

Is the focus correctly adjusted? Adjust the focus. P24
Is the unit placed too near or too far away from the screen? Set the unit at a correct distance from the screen. P21 to 22

Has setting been performed for screen mask? Set “Mask” in the setting menu to “Off”. P27,38 - 20
Is the display out of position? Alter the “Picture Position” value in the setting menu to ensure that images are not missing. P36 - 15

Are batteries installed correctly? Match the polarities ( or ) correctly when inserting the batteries. P15
Is there an obstructive object between the remote control and remote sensor?
Is the remote control held too far away from the unit?
Hold the remote control closer to the sensor when using. P15
Has setting been performed for off timer? Set “Off Timer” in the setting menu to “Off”. P41 - 37

No device is connected to the input terminal. The input terminal is connected but there is no signal.
COMP.
Input the video signals.
A video signal that cannot be used in this unit has been input.
COMP.
Input video signals that can be used.
* The names of input terminals such as COMP. will be displayed in yellow. This message is displayed when the accumulated lamp time has exceeded 2900 hours. To clear the message, press the [Back] button.
Get ready a new lamp unit and replace as soon as possible. Reset the
lamp time after replacing the lamp. ( P48 to 50)

The accumulated lamp time or warning mode of this unit is displayed by the indicators. For information on indicator display during normal operation, see “Controls and Features”. ( P12)
No.
Content WARNING LAMP STANDBY/ON
2 - - Light on
(Green) - - - When the power on (Hide Off)
Indicator display in normal conditions.
0.5 second continuous - When the power on (Hide On)
4 - - Blinking (Red) 0.5 second continuous - During cool down
Lamp replacement is near ( P48 to 50) (When accumulated lamp time has exceeded 2900 hours)
Lamp has reached the end of life ( P48 to 50) (When accumulated lamp time has exceeded 3000 hours)
0.25 second 1 time 0.75 second
Lamp does not light up and unit is unable to project
8 0.25 second 2 times 0.75 second Lamp is turned off during projection
9 0.25 second 3 times 0.75 second Lamp cover is removed
0.25 second 1 time 0.75 second Abnormalities in the power supply
11 0.25 second 2 times 0.75 second
Cooling fan stops (cooling fan gets caught)
12 0.25 second 3 times 0.75 second
Internal temperature is too high (abnormal internal temperature)
13 0.25 second 4 times 0.75 second
External temperature is too high (abnormal external temperature)
14 0.25 second 1 time 0.75 second
Abnormal electrical circuit (abnormal startup of drive circuit)
Abnormal electrical circuit (abnormal communication of the drive circuit)
15 0.25 second 2 times 0.75 second
16 0.25 second 3 times 0.75 second
Abnormal electrical circuit (abnormal drive circuit of image)
17 0.25 second 4 times 0.75 second Abnormalities in the automatic lens cover
When the unit enters into warning mode (No. 7 to 17), it will automatically stop projection, and run the cooling fan for about 60 seconds. After the cooling fan has stopped, pull out the power plug from the power outlet. Then, follow the procedures below.

If the warning indication is displayed again, please wait for the cooling fan stopped, then pull out the power plug from the power outlet. Then call your authorized dealer for repair.

The lamp is a consumable item. If the image is dark or the lamp is turned off, replace the lamp unit. ● When the lamp replacement time approaches, a message is displayed on the screen and the condition is indicated by the
indicator. ( P46, 47)
Remove the lamp cover ● Remove the screws with a screwdriver.
Loosen the screws on the lamp unit ● Loosen the screws with a screwdriver.
progresses rapidly. ● If the picture becomes dark, the tint becomes strange, or the image flickers, promptly the lamp unit for a new one.
Pull out the lamp unit ● Grasp the handle and pull out the lamp unit.
5 Troubleshooting · Handle




Tighten the screws of the new lamp unit ● Tighten the screws with a screwdriver.


ON Resetting Lamp Time
After replacing the lamp, reset the lamp time.
HDMI 1
HDMI 2
COMP.
S-VIDEO
PC
outlet
LENS
ASPECT HIDE
2 Must operate with the remote control in the standby mode (the projector is powered, but is not turned on). ● Press in the order as shown.
BACK
PICTURE MODE
BACK OK
HIDE
CINEMA 1
CINEMA 2
CINEMA 3
NATURAL STAGE DYNAMIC
Press for 2 seconds or more
USER1
LENS. AP.
PIC. ADJ.
3 seconds. After that, the unit switches to standby mode.
LAMP
ST ANDBY/ON
CAUTION
5 Troubleshooting · Light on (Red)

Clean the filter regularly or air intake efficiency may deteriorate and malfunction may occur.
Lift up while pushing the claw
Clean the filter
If the filter is damaged or too dirty to be cleaned
Check that the left and right claws are locked onto the unit

Control of this unit via a computer is possible by connecting the computer to this unit with a RS-232C cross cable (D-Sub 9 pin).


Start Bit Stop Bit
The command between this unit and the computer consists of “Header”, “Unit ID”, “Command”, “Data” and “End”. ● Header (1 byte), Unit ID (2 bytes), Command (2 bytes), Data (n bytes), End (1 byte)
This binary code indicates the start of communication.

This unit→PC (When the command is accepted without error, it returns to PC)
This code specifies the unit. The binary code is fixed at “8901”.
6 Others



0000 Connection check Check whether communication is available between this unit and the PC during standby.
5243 Remote Control Sends the same code as the supplied remote control. ● “Remote control code” ( P54)
Reference command and data (Binary code)

During standby or power on 30: Standby mode 31: Power-on mode 32: During Cool Down mode 34: Warning mode


37 33 30 31 TEST 37 33 35 39
37 33 30 32 CINEMA 3 37 33 36 36
BACK 37 33 30 33 STAGE 37 33 36 37
ON 37 33 30 35 CINEMA 2 37 33 36 38
STAND BY 37 33 30 36 CINEMA 1 37 33 36 39
HIDE 37 33 31 44 NATURAL 37 33 36 41
LENS.AP. 37 33 32 30 DYNAMIC 37 33 36 42
MENU 37 33 32 45 USER 1 37 33 36 43
OK 37 33 32 46 USER 2 37 33 36 44
LENS 37 33 33 30 THX 37 33 36 46
37 33 33 34 HDMI 1 37 33 37 30
37 33 33 36 HDMI 2 37 33 37 31
MENU POSITION 37 33 34 32 PIC.ADJ. 37 33 37 32
PC 37 33 34 36 GAMMA 37 33 37 35
VIDEO 37 33 34 41 C.TEMP 37 33 37 36
S-VIDEO 37 33 34 42 ASPECT 37 33 37 37
6 Others


This section shows the communication examples of RS-232C.
Connection check PC→This unit: 21 89 01 00 00 0A This unit→PC: 06 89 01 00 00 0A Connection check
Power (On) PC→This unit: 21 89 01 50 57 31 0A This unit→PC: 06 89 01 50 57 0A
When power is turned on from standby mode
Power (Off) PC→This unit: 21 89 01 50 57 30 0A This unit→PC: 06 89 01 50 57 0A
When power is turned off (standby mode) from power-on mode
Input (COMP.) PC→This unit: 21 89 01 49 50 32 0A This unit→PC: 06 89 01 49 50 0A When video input is set to component
When the same operation as pressing the [MENU] button on the remote control is made
PC→This unit: 21 89 01 52 43 37 33 32 45 0A This unit→PC: 06 89 01 52 43 0A
PC→This unit: 3F 89 01 50 57 0A This unit→PC: 06 89 01 50 57 0A This unit→PC: 40 89 01 50 57 31 0A
When information of power-on mode is acquired
PC→This unit: 3F 89 01 49 50 0A This unit→PC: 06 89 01 49 50 0A This unit→PC: 40 89 01 49 50 30 0A
When information of S-VIDEO input is acquired

About Trademarks and Copyrigh t
D-ILA Device Characteristics
Maintenance Procedures
Do not project still pictures or pictures that have still segments for a long period of time. The still parts of the picture may remain on the screen. Take special notice of images on the screens of video games and computer programs. There is no problem when playing normal video images such as movies.
Prolonged disuse of the unit may effect an error on the functions. Turn on the power occasionally and operate the unit.
This unit contains parts (optical part, cooling fan, etc.) that require replacement to maintain its functioning. The estimated time for parts replacement varies greatly depending on the usage and environment. Please consult your authorized dealer for replacement.
6 Others

Measures to prevent the unit from toppling or dropping should be taken for safety reasons and accident prevention during emergencies including earthquakes. When mounting this unit on a pedestal or ceiling, remove the 4 feet on the bottom surface and use all the 4 screw holes (M5 screws) to mount.


Product Name D-ILA Projector
Display Panel/Size D-ILA device
*1 *2 / 0.7" (1920pixels x 1080pixels) x 3 (Total no. of pixels: Approx. 6.22million)
Projection Lens 2.0 x power zoom lens (1.4:1 to 2.8:1)(Zoom/Focus: Power)
Light-source Lamp 200 W Ultra-high pressure mercury lamp [Part No. : BHL5010-S] Average lifespan: 3000 hours (normal mode)
Screen Size Approx. 60" to 200" (Aspect ratio: 16:9)
objection Distance Approx. 1.8m to 12m
Color System NTSC, NTSC4.43, PAL, PAL-M, PAL-N, SECAM (Auto/Manual switch)
Analog Video Input Format 480i, 480p, 576i, 576p, 720p/50Hz, 720p/60Hz, 1080i/50Hz, 1080i/60Hz
Digital Video Input Format 480i, 480p, 576i, 576p, 720p/50Hz, 720p/60Hz, 1080i/50Hz, 1080i/60Hz, 1080p/24Hz, 1080p/50Hz, 1080p/60Hz, PC compatible signals ( P59)
Resolution 1920 dots x 1080 dots
Video Input (VIDEO)
1-line, RCA pin jack x 1 1.0V(p-p), 75Ω
1-line, mini DIN 4 pin x 1 Y: 1.0V(p-p), 75Ω C: 0.286V(p-p), 75Ω(NTSC); 0.3V(p-p), 75Ω(PAL)
S-video Input (S-VIDEO)
1-line, RCA pin jack x 3 Y: 1.0V(p-p), 75Ω CB/PB, CR/PR: 0.7V(p-p), 75Ω HDMI Input (HDMI 1, HDMI 2)
Component Video Input (COMPONENT)
2-line, HDMI 19 pin x 2(HDCP compliant) *3
Compatible with the HDMIv1.3a standard
PC Input 1-line, D-Sub 15 pin VGA
Trigger Output 12V 100mA
Power Requirements AC 110V-240V 50/60 Hz
Temperature: 5℃ to 35℃ Humidity: 20% to 80% (No condensation) (Storage Temperature: -10℃ to 60℃)
Installation Height Below 1524m
Dimensions (Width x Height x Depth) 365mm X 167mm X 477.5mm
Mass 11.2kg
Accessories (See P11)
*1 D-ILA is the abbreviation for Direct drive Image Light Amplifier.
*2 D-ILA devices are manufactured using extremely high-precision technology. Pixel effectiveness is 99.99%. Only 0.01% or less of the pixels are either missing or would remain permanently lit up.
*3 HDCP is the abbreviation for High-bandwidth Digital Content Protection system.
comprehension. Images may differ from the actual product.

No. of effective
No. of effective
Polarity Total No.
Total No.
No. Designation Resolution fh [kHz]
lines [line] H V
1 VGA 60 640 X 480 31.500 60.000 25.200 - - 800 525 640 480
2 VGA 59.94 640 X 480 31.469 59.940 25.175 - - 800 525 640 480
3 SVGA 60 800 X 600 37.879 60.317 40.000 + + 1,056 628 800 600
4 XGA 60 1024 X 768 48.363 60.004 65.000 - - 1,344 806 1,024 768
5 WXGA 60 1280 X 768 47.760 60.000 79.998 - + 1,675 796 1,280 768
6 WXGA +60 1440 X 900 55.919 59.999 106.470 - + 1,904 932 1,440 900
7 SXGA 60 1280 X 1024 63.981 60.020 108.000 + + 1,688 1,066 1,280 1,024
8 WSXGA +60 1680 X 1050 65.222 60.002 147.140 - + 2,256 1,087 1,680 1,050
9 WUXGA 60 1920 X 1200 74.038 59.95 154.000 + - 2,080 1,235 1,920 1,200
Images may not be displayed if the above timings are not met.
Polarity Total No.
No. of effective
No. of effective
Total No.
No. Designation Resolution fh [kHz]
lines [line] H V
1 VGA 60 640 X 480 31.500 60.000 25.175 - - 800 525 640 480
2 VGA 72 640 X 480 37.900 72.000 31.500 - - 832 520 640 480
3 VGA 75 640 X 480 37.500 75.000 31.500 - - 840 500 640 480
4 VGA 85 640 X 480 43.300 85.000 36.000 - - 832 509 640 480
5 SVGA 56 800 X 600 35.200 56.000 36.000 + + 1024 625 800 600
6 SVGA 60 800 X 600 37.900 60.000 40.000 + + 1056 628 800 600
7 SVGA 72 800 X 600 48.100 72.000 50.000 + + 1040 666 800 600
8 SVGA 75 800 X 600 46.900 75.000 49.500 + + 1056 625 800 600
9 SVGA 85 800 X 600 53.700 85.000 56.250 + + 1048 631 800 600
10 XGA 60 1024 X 768 48.400 60.000 65.000 - - 1344 806 1024 768
11 XGA 70 1024 X 768 56.500 70.000 75.000 - - 1328 806 1024 768
12 XGA 75 1024 X 768 60.023 75.029 78.750 + + 1312 800 1024 768
13 XGA 85 1024 X 768 68.700 85.000 94.500 + + 1376 808 1024 768
14 WXGA 60 1280 X 768 47.760 60.000 79.998 - + 1675 796 1280 768
15 WXGA+ 60 1440 X 900 55.919 59.999 106.470 - - 1904 932 1440 900
16 SXGA 60 1280 X 1024 63.981 60.020 108.000 + + 1688 1066 1280 1024
17 SXGA+ 60 1400 X 1050 64.740 59.950 101.000 + + 1560 1080 1400 1050
18 WSXGA+ 60 1680 X 1050 65.222 60.002 147.140 - - 2256 1087 1680 1050
19 1920x1080 60 1920 X 1080 67.500 60.00 148.500 + + 2200 1125 1920 1080
20 MAC13" 640 X 480 35.000 66.667 30.240 - - 864 525 640 480
21 MAC16" 832 X 624 49.107 75.087 55.000 - - 1120 654 832 624
22 MAC19" 1024 X 768 60.241 74.927 80.000 - - 1328 804 1024 768
Images may not be displayed if the above timings are not met.

Dimensions
90.6 42.5 105
365 236 64.5
198 Lens center Lamp cover
6 Others

MANUEL D’INSTRUCTIONS
PROJECTEUR D-ILA
DLA-RS25
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.