
WIDE LCD PANEL TV INSTRUCTIONS

Thank you for buying this JVC LCD flat television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. (“LCD” stands for Liquid Crystal Display.)
APPLIANCE TO RAIN OR MOISTURE.




Pixel defects LCDs use collections of fine points (“pixels”) to display images. While there is no problem with more than 99.99% of these pixels, please understand that a very small number of pixels may not light, or may light all the time.
Avoid improper installation and never position the unit where good ventilation is impossible. When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture. Keep to the minimum distance guidelines shown for safe operation.
200 mm 200 mm
150 mm 150 mm
Failure to take the following precautions may cause damage to the television or remote control. DO NOT block the TV’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.) DO NOT place anything on top of the TV.
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.) DO NOT allow objects or liquid into the cabinet openings.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.) DO NOT place any naked flame sources, such as lighted candles, on the TV. DO NOT subject the TV to direct sunlight.

The surface of the TV screen is easily damaged. Be very careful with it when handling the TV. Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never use any cleaner or detergent on it.
If there is a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover.
50 mm

Cleaning the screen
The screen is coated with a special thin film to reduce reflection. If this film is damaged, uneven colours, discolouration, scratches, and other problems that cannot be repaired may occur. Pay attention to the following when handling the screen.
D.I.S.T. demonstration To start the D.I.S.T. demonstration: Press the H button to display the menu bar. Then press the yellow button. A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.
To quit the D.I.S.T. demonstration: Press the yellow button, b button, 6 p buttons or any of the number buttons.


This TV comes with a table top stand already attached. This stand can be used to adjust the direction of the TV screen 5° up, 10° down, and 20° to the left or right.
Tilt the TV up and down:
While holding the bottom of the stand with one hand, use your other hand to hold the middle of the top of the TV and slowly tilt the TV up and down.

Rotate the TV to the left and right:
While holding the bottom of the stand with one hand, use your other hand to hold the edge of the panel and slowly adjust the direction of the TV screen.


Setting up your TV

A cable holder which is used to keep the connection cables tidy is attached to the back of the stand. Gently squeeze the left and right of the cable holder and pull it to remove it from the stand. After putting the cables in the cable holder, attach it to the back of the stand again.
There are connection terminals behind the covers on the left and right of the rear of the TV. Remove these two covers before connecting an antenna or VCR.

Remove the covers by removing the hooks. When replacing the covers, place the side of the covers against the TV and insert the hooks.

Setting up your TV

If not connecting a VCR (follow 1): Connect an aerial cable to the aerial socket on this TV.
If connecting a VCR: 1 Connect the aerial cable to the aerial input socket on the VCR, and connect the VCR and TV with another aerial cable
2 Connect the VCR’s VIDEO OUT (video output) terminal and the TV’s VIDEO terminal with a video cable To connect a VCR to the TV with an S- VIDEO cable: Connect the VCR’s S-VIDEO OUT (S- VIDEO output) terminal and TV’s S VIDEO terminal with an S-VIDEO cable A, instead of connecting with a video cable. Note that the connection with a video cable will be ignored in case you connect a VCR to the TV with both video cable and S-VIDEO cable.
3 Connect the VCR’s VIDEO OUT (audio L/R output) terminals and the TV’s AUDIO terminals with an audio cable
without terminal covers

Setting up your TV

When the TV is first turned on, it goes into the initial settings mode, and you will see the JVC logo. Follow the instructions on the screen display to make the initial settings.
Insert the AC plug on the power cord from the TV into AC outlet. Caution
Use two AA/R6 dry cell batteries. Insert the batteries from the - end, making sure the + and - polarities are correct.
1 Make sure to set the PIP/TV/DVD switch on the remote control to the TV position
2 Press the # button on the remote control The TV turns on from standby mode and the JVC logo is displayed.

Setting up your TV
5 Press the 6 buttons to choose a group. Then press the a button The AUTO PROGRAM function starts. The TV channels you receive are automatically stored in the programme numbers (PR) list.
3 Press the a button The LANGUAGE menu appears.

6 After the TV channels have been registered in the programme numbers (PR), the EDIT menu appears
4 Press the 6 buttons to choose ENGLISH. Then press the a button The TELETEXT LANGUAGE menu appears. Set the teletext language group that corresponds to the language of the teletext programme that you want to watch. For details, see “TELETEXT LANGUAGE” on page 39.

GROUP-1
GROUP-2 GROUP-3 GROUP-4
Now, setting up is complete. Please enjoy your new JVC TV!
>> · 14%


Press the A button or the CHANNEL p buttons to turn the TV on from standby mode. When the TV is turned on, the power lamp lights blue.

Press the CHANNEL p buttons to choose a programme number (PR) or a VIDEO terminal Press the TV/VIDEO button to choose a VIDEO terminal.
Press the VOLUME q buttons The volume level indicator appears.
Use the MENU/OK button Refer to “Using the TV’s menu” (see page 23) for details of using the menu.
Refer to the pages in parentheses for details. 1 Remote control sensor 2 Power lamp (page 8) 3 TV/VIDEO button 4 MENU/OK button (page 23) 5 CHANNEL p buttons 6 (page 23) 6 VOLUME q buttons 5 (page 23) 7 A (Stand by) button 8 Headphone jack (mini jack) (page 41)

1 Muting button 2 Number buttons 3 1 button 4 c button 5 2 button 6 4 button 7 7 buttons 8 5 button 9 6 p buttons 0 VCR/DVD/Teletext control buttons - p buttons = d (Favourite) button ~ # (Standby) button ! PIP/TV/DVD switch @ g (Text) button # Colour buttons $ H button % a button ^ b button & 7 q buttons * f (Freeze) button ( X (Multi) button ) c (Select) button

Press the # (standby) button to turn the TV on or off When the TV is turned on, the power lamp lights blue.

To turn the TV on or off, set the PIP/TV/ DVD switch on the remote control to the TV position and press the # button. If the PIP/TV/DVD switch on the remote control is set to the DVD position, the TV will not be turned on or off even if the # button is pressed.

Remote control buttons and functions
Use the number buttons:
Enter the programme number (PR) of the channel using the number buttons. Example:
To return to a TV channel: Press the 4 button, the 6 p buttons or the number buttons.
Use the 6 p buttons:
Press the 6 p buttons to choose the programme number (PR) you want or a VIDEO terminal.
To use the programme number PR 0 (AV): When the TV and VCR are connected only by the aerial cable, choosing the programme number PR 0 (AV) allows you to view images from the VCR. Set the VCR RF channel to the programme number PR 0 (AV) manually. For details, see “EDIT/ MANUAL” on page 34.
Use the 4 button:
Press the 4 button to choose a VIDEO terminal.


Remote control buttons and functions
PR LIST: The programme number (PR) and VIDEO terminal list is displayed. Pressing the a button after choosing the programme number (PR) or VIDEO terminal with the 7 buttons will display the chosen programme or VIDEO terminal.
Press the 7 q buttons to adjust the volume. The volume level indicator appears and the volume changes as you press the 7 q buttons. Muting the sound
Press the l (muting) button to turn off the sound. Pressing the l (muting) button again restores the previous volume level.
You can see the channel number of the programme you are watching or the PR LIST. From the PR LIST, you can choose a channel or VIDEO terminal.
Press the 5 button to display the information you want to see. Pressing the 5 button changes the display as follows:

AV 01 02 03 04 05 06 07 08 09
Channel number display: The channel number and channel name (when the channel name is registered) of the programme you are watching or the VIDEO terminal number is displayed.
Channel number display

Remote control buttons and functions

16:9 ZOOM: This zooms up the wide picture (16:9 aspect ratio) to the full screen.
You can change the screen size according to the picture aspect ratio. Choose the optimum one from the following ZOOM modes.
16:9 ZOOM SUBTITLE: This zooms up the wide picture (16:9 aspect ratio) with subtitles to the full screen.
AUTO: When a WSS (Wide Screen Signalling) signal, which shows the aspect ratio of the picture, is included in the broadcast signal or the signal from an external device, the TV automatically changes the ZOOM mode to 16:9 ZOOM mode or FULL mode according to the WSS signal. If a WSS signal is not included, the picture is displayed according to the ZOOM mode set with the 4:3 AUTO ASPECT function.
FULL: This uniformly stretches the left and right sides of a normal picture (4:3 aspect ratio) to fill the wide TV screen.
Choose the ZOOM mode
1 Press the c button to display the ZOOM menu
REGULAR: Use to view a normal picture (4:3 aspect ratio) as this is its original shape.

REGULAR PANORAMIC 14:9 ZOOM 16:9 ZOOM 16:9 ZOOM SUBTITLE FULL
PANORAMIC: This stretches the left and right sides of a normal picture (4:3 aspect ratio) to fill the screen, without making the picture appear unnatural.
2 Press the 6 buttons to choose a ZOOM mode. Then press the a button The picture expands and the chosen ZOOM mode is displayed in about 5 seconds.
14:9 ZOOM: This zooms up the wide picture (14:9 aspect ratio) to the upper and lower limits of the screen.

Remote control buttons and functions
Adjusting the visible area of the
picture If subtitles or the top (or bottom) of the picture are cut off, you can adjust the visible area of the picture manually.
1 Press the c button The ZOOM menu appears.
MONO: Select the MONO mode, when you listen to the mono sound. You can enjoy the sound for a wider audience similar to stereo sound.
2 Press the a button to display the ZOOM mode indicator The indicator appears.
OFF: The CINEMA SURROUND function switches off.
3 While it is displayed, press the 6 buttons to change the position of the picture
The visible area adjustment is saved even after the TV channel is changed. However, it is cancelled if the following operations are performed.
You can view the current programme as a still picture.
1 Set the PIP/TV/DVD switch to the PIP position When using the “Freeze” function, set the PIP/TV/DVD switch to the PIP position.
2 Press the f button The still picture of the current picture will appear.
You can enjoy sounds with a wider ambience.
Press the 2 button to select one of CINEMA SURROUND modes
HIGH/LOW: When you listen to stereo sound, please select HIGH or LOW mode. You can enjoy sound similar to the experience at the theatre. When you combine the functions of A.H.B. and BBE, you can enjoy more powerful sound.
current programme · still picture

Remote control buttons and functions
To cancel the “Freeze” function: Press the f button, the 6 p buttons or the number buttons.
12-pictures multi:
1 Set the PIP/TV/DVD switch to the PIP position When using the “Multi-picture” function, set the PIP/TV/DVD switch to the PIP position.
2 Press the X button The “Multi-picture” menu appears.
3 Press the 5 buttons to choose the number of screens and then press the a button
Choose to return to one screen.
Choose to change to 2-pictures multi.
Choose to change to 12-pictures multi.
2-pictures multi:
With 1125i and 750p signals, the screen is split into two as shown below.

Remote control buttons and functions
To return the “Multi-picture” to one screen: Press the X button, press the 5 buttons to choose one screen, and then press the a button.
The TV temporarily memorises the TV channel that was chosen right before the current TV channel as the “Last Channel”. By pressing the 1 button, you can alternately view the current TV channel and the “Last Channel”. If you want to view two channels alternately by using the Return function, first choose one TV channel and then choose the other TV channel with the number buttons. If you choose the TV channel without using the number buttons, there are cases where a channel other than the one you first chose is registered as the “Last Channel”.
The 1 button has two functions; the RETURN PLUS function and the Return function. If a channel has been registered as the “Return Channel”, the RETURN PLUS function operates. If there is no setting for the “Return Channel”, the Return function operates.
By registering a channel you frequently view as the “Return Channel”, you can select that channel at any time simply by pressing the 1 button.
To register a TV channel as the “Return Channel”: Choose the Programme number to which the channel you want to register has been set, and press the 1 button and hold for more than 3 seconds continuously. “RETURN PLUS PROGRAMMED!” is displayed and the registration is completed.
To cancel a TV channel registered as the “Return Channel”: While viewing any TV channel, press the 1 button and hold for more than 3 seconds continuously. “RETURN PLUS CANCELED!” is displayed and the registration is cancelled.
Return function

Remote control buttons and functions
Calling the favourite channel
1 In the normal screen, press the d (favourite) button Then “FAVOURITE1-4?” appears.
You can register your favourite TV channels (PR 1 – PR 99) in the number buttons 1 to 4. After registering, the channel can be called by pressing the d (favourite) button and a number button 1 to 4. Favourite channel registration
2 Press one of the number buttons 1 to 4 The called favourite channel appears on the screen.
1 In the normal screen, choose a TV channel (PR 1 – PR 99) that you want to register For details, refer to “Choose a TV channel and watch images from external devices” on page 12.
Setting the picture effect
When a favourite channel has been chosen with the d (favourite) button and number buttons 1 to 4, picture effect settings can be memorised for each favourite channel by setting the picture effects in the PICTURE menu (see page 25). The following items in the PICTURE menu (see page 25) are memorised. PICTURE MODE BACK LIGHT CONTRAST BRIGHT SHARP COLOUR TINT WHITE BALANCE DIGITAL VNR COLOUR SYSTEM The last setting made for each item is memorised.
2 Press and hold the d (favourite) button for three seconds or more Then “SET 1-4?” appears on the screen.
3 Press one of the number buttons 1 to 4 The current channel is registered in the pressed number button. After “PROGRAMMED!” appears on the screen, the favourite channel icon appears at the top-right of the screen.

Remote control buttons and functions
These buttons will operate a JVC brand DVD player. Pressing a button that looks the same as the device’s original remote control button has the same effect as the original remote control.
1 Set the PIP/TV/DVD switch to the DVD position When you are operating the DVD player, set the switch to the DVD position.
2 Press the DVD control button to control your DVD player

You cannot turn the TV on or off when the PIP/TV/DVD switch is set to the DVD position. When you turn the TV on or off, set the PIP/TV/DVD switch to the TV position.

4 Choose a teletext page by pressing the 6 p buttons, number buttons or colour buttons
To return to the TV mode: Press the 4 button, b button, or g (Text) button.
1 Choose a TV channel with a teletext broadcast
2 Set the PIP/TV/DVD switch to the TV position
You can store the numbers of your favourite teletext pages in memory and call them up quickly using the colour buttons.
To store the page numbers:
3 Press g (Text) button to display the teletext Pressing g (Text) button changes the mode as follows:
1 Press B button to go into the List mode The page numbers you have stored are displayed at the bottom of the screen.



2 Press a colour button to choose a position. Then press the number buttons to enter the page number
Some teletext pages include sub-pages that are automatically displayed.
1 Choose a teletext page that includes sub-pages Sub-page numbers that can be viewed are automatically displayed at the top of the screen.
3 Press and hold down the A (Store) button The four page numbers blink white to show that they are stored in memory.
2 Press the 5 buttons to choose a sub-page number
To call up a stored page:
Some teletext pages include hidden text (such as answers to a quiz). You can display the hidden text.
1 Press the B button to enter the List mode
Each time you press the E (Reveal) button, text is hidden or revealed
2 Press a colour button having a stored page

To exit the List mode: Press the B button again.
You can double the height of the teletext display.
You can hold a teletext page on the screen for as long as you want, even while several other teletext pages are being received.


To cancel the Hold function: Press C (Hold) button again.
Teletext function


This TV has a number of functions you can operate using menus. To use all your TV’s functions, you need to understand the basic menu operating techniques fully.
PICTURE menu Choose to set the screen settings.
Buttons used to operate the menus
SOUND menu Choose to set the sound settings.
FEATURES menu Choose to set the sleep timer and child lock settings.
SET UP menu Choose to edit the channels or set the display language settings.
1 Press the H button to display the menu bar
The menu guide area can be made to appear and disappear for some menus. While the menu is displayed, press the 5 button to change between the guide area being displayed and not displayed.
2 Press the 5 buttons to choose the menu you want to use and then press the a button
PANORAMIC
REGULAR 14:9 ZOOM
PICTURE
-EN Chosen menu name Chosen menu
3 Press the 6 buttons to choose the item to be set, press the 5 buttons to set the item, and then press the a button If there are sub-menus, use the 7 buttons to operate them.
PANORAMIC REGULAR 14:9 ZOOM

Using the TV’s menu
Operation with the buttons on the TV You can also operate the menus using the buttons on the front panel of the TV.



You can adjust the back light. 2 :darker 3 : brighter
You can adjust the picture contrast. 2 :lower 3 : higher
You can adjust the picture brightness. 2 :darker 3 : brighter
You can adjust the picture sharpness. 2 :softer 3 : sharper
You can adjust the picture colour. 2 :lighter 3 : deeper
You can adjust the picture tint. 2 :reddish 3 : greenish • You can change the TINT setting (picture hue) when the colour system is NTSC 3.58, or NTSC 4.43.
You can choose one of three PICTURE MODEs to adjust the picture settings automatically.
BRIGHT: Heightens contrast and sharpness.
You can select one of three WHITE BALANCE modes (three tones of white) to adjust the white balance of the picture. Since white is the colour which is used as a reference for all the other colours, changing the WHITE BALANCE mode affects the appearance of all the other colours on the screen.
STANDARD: Standardises picture adjustment.
SOFT: Softens contrast and sharpness.

COOL: A bluish white. Using this mode when watching bright pictures allows you to enjoy a more vivid and bright picture.
MIN: The level of the DIGITAL VNR effect is set to the minimum. If you set the DIGITAL VNR function to AUTO(LOW) but feel that the sharpness of the original picture has not been reproduced fully, change the setting from AUTO(LOW) to MIN.
MID: The normal white colour.
WARM: A reddish white. Using this mode when watching films allows you to enjoy colours that are characteristic of films.
MAX: The level of the DIGITAL VNR effect is set to the maximum. If you set the DIGITAL VNR function to AUTO(HIGH) but still notice some noise, change the setting from AUTO(HIGH) to MAX.
Choose FEATURES and press the a or 3 button to display the sub-menu.

PULL DOWN COLOUR MANAGEMENT PICTURE MANAGEMENT COLOUR SYSTEM 4:3 AUTO ASPECT
The Super DigiPure function uses the latest in digital technology to give you a natural- looking picture. The Super DigiPure function includes the following two functions. DigiPure function: This function helps to create a natural- looking picture by eliminating unnecessary edges from high-contrast and crisp images. For images with low-contrast, edges are added to produce a sharper, more detailed picture. You can choose from the three DigiPure function settings of AUTO, MIN and MAX.
The DIGITAL VNR function cuts down the amount of ‘noise’ (‘snow’ or interference) in the original picture. You can choose from the three DIGITAL VNR function settings of AUTO, MIN and MAX.
AUTO(LOW)/AUTO(HIGH): The TV will automatically adjust the level of the DIGITAL VNR effect to match the amount of noise in the picture, giving you the best possible picture.
PICTURE menu · Super DigiPure

AUTO: The TV will automatically adjust the level of the DigiPure effect to match the amount of noise in the picture, giving the best possible picture. MIN: The level of DigiPure effect is set to the minimum. When you set the Super DigiPure function to AUTO and notice some noise, change the setting from AUTO to MIN.
This TV supports the COLOUR MANAGEMENT function to ensure dull colours are compensated to produce natural hues. The COLOUR MANAGEMENT function is on by default. ON: COLOUR MANAGEMENT function is turned on. OFF: COLOUR MANAGEMENT function is turned off.
The PICTURE MANAGEMENT function makes it easier to see the dark areas when a picture has many dark areas, and makes it easier to see the bright areas when a picture has many bright areas. Normally use with this function on. ON: PICTURE MANAGEMENT function is turned on. OFF: PICTURE MANAGEMENT function is turned off. COLOUR SYSTEM
The PULL DOWN function displays a cinema film picture more smoothly and naturally on the screen. AUTO: The television automatically recognises the type of signal and turns the function on and off. ON: This function is turned on. OFF: This function is turned off.
The colour system is chosen automatically. However, if the picture is not clear or no colour appears, choose the colour system manually.
1 Choose COLOUR SYSTEM. Then press the a or 3 button The sub-menu of the COLOUR SYSTEM function appears.

PICTURE menu

2 Press the 5 buttons to choose MAIN or SUB MAIN: You can change the colour system of the main-picture. SUB: You can change the colour system of the sub-picture.
For colour system in your country or region, refer to the table below:

Bahrain, Kuwait, Oman, Qatar, United Arab Emirates, Yemen, etc. Indonesia, Malaysia, Singapore, Thailand, India, etc.
China, Vietnam, etc. PAL Hong Kong, etc. PAL Islamic Republic of Iran, Lebanon, Saudi Arabia, etc. SECAM
3 Press the 6 buttons to choose the appropriate colour system. Then press the a button PAL: PAL system SECAM: SECAM system NTSC 3.58: NTSC 3.58 MHz system NTSC 4.43: NTSC 4.43 MHz system AUTO: This function detects a colour system from the input signal.
Russia, etc. SECAM Czech Republic, Poland, etc. PAL Germany, Holland, Belgium, etc. PAL
UK, etc. PAL Oceania Australia, New Zealand, etc. PAL
Republic of South Africa, etc. PAL Nigeria, etc. PAL Egypt, Morocco, etc. SECAM
You can choose one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio).
1 Choose 4:3 AUTO ASPECT then press the a button

2 Press the 6 buttons to choose a ZOOM mode
PICTURE menu


You can adjust the high tone of the sound. 2 :weaker 3 : strong
You can adjust the volume balance between the left and right speaker. 2 :turn the left speaker’s volume level up. 3 : turn the right speaker’s volume level up.
CINEMA SURROUND
When you are viewing a bilingual broadcast programme, you can choose the sound from Bilingual I (Sub I) or Bilingual II (Sub II). If you have poor reception on a stereo broadcast, you can change from stereo to mono sound so that you can hear the broadcast more clearly and easily.
You can enjoy Surround sound with a “live” effect by using the CINEMA SURROUND function.
Used when you want to emphasise the bass sound.
ON: This function is turned on.
OFF: This function is turned off.
You can adjust the low tone of the sound. 2 :weaker 3 : strong

BBE function restores clarity and presence for better speech intelligibility and musical realism.
ON: This function is turned on.
OFF: This function is turned off.
SOUND menu

To cancel the SLEEP TIMER function: Press the 2 button to set the period of time to “OFF”.
SLEEP TIMER CHANNEL GUARD APPEARANCE BLUE BACK CHILD LOCK AUTO SHUTOFF
ON OFF
OFF
FAVOURITE SETTING
CHANNEL GUARD
When there is a TV channel you do not want your children to watch, you can use the CHANNEL GUARD function to lock out the TV channel. Even when a child chooses a programme number (PR) for a locked TV channel the screen will change to blue and display n (CHANNEL GUARD) so the TV channel cannot be viewed. Unless you enter a pre-set ID number by a special operation, the lock cannot be released and the child cannot view the TV channel.
You can set the TV to automatically turn off after a set period of time.
1 Choose SLEEP TIMER. Then press the a or 3 button A Sub-menu of the SLEEP TIMER function appears.
To set the CHANNEL GUARD

1 Choose CHANNEL GUARD, then press the 0 button “SET ID NO.” (ID number setting screen) appears.

2 Set the ID number to your liking
1 Press the 6 buttons to choose a number.
2 Press the 5 buttons to move the cursor.

3 Press the a button The Sub-menu of CHANNEL GUARD appears.
2 Press the 5 button to display “ID NO.” (ID No. input screen)

21 22 23 24 25 26 CC CC CC
3 Press the number buttons to enter the ID number The lock is temporarily released so you can view the TV channel.
If you have forgotten the ID number: Perform step 1 of “To set the CHANNEL GUARD function”. After confirming the ID number, press the 4 button to exit the menu.
4 Press the 6 buttons to choose a TV channel Every time you press the 6 buttons, the Programme number (PR) changes, and the picture of the TV channel registered in the Programme number (PR) is displayed on the screen.
5 Press the blue button and set the CHANNEL GUARD function. Then press the a button n (CHANNEL GUARD) appears and the TV channel is locked.
To reset the CHANNEL GUARD function: Press the blue button again. n (CHANNEL GUARD) disappears.
To disable easy resetting of the CHANNEL GUARD function, the menu disappears if you choose the CHANNEL GUARD function and press the a button.
To view a locked TV channel
1 Choose a programme number (PR) of a locked TV channel with the number buttons or PR LIST The screen changes to blue and the n (CHANNEL GUARD) appears. You cannot view the TV channel.
FEATURES menu

AUTO SHUTOFF
Press the 5 button and choose the format in which the channel number is displayed from the four types: TYPE A, TYPE B, TYPE C, and TYPE D.
You can set the power to turn off if no signal is received and no operation is performed for about 15 minutes or longer after the end of a broadcast.
ON: This function is turned on.
OFF: This function is turned off.
You can set the TV to automatically change to a blue screen and mute the sound if the signal is weak or absent, or when there is no input from an external device.
Chose when deleting the favourite channels registered in the buttons 1 to 4.
ON: This function is turned on.
1 Choose FAVOURITE SETTING, then press the a or 3 button The FAVOURITE SETTING menu appears.
OFF: This function is turned off.

You can disable the front control buttons of the TV. When this function is set to ON, the TV can be operated only by using the remote control. Use this function to prevent children from operating the TV at their own discretion (without parent consent).
ON: This function is turned on.
OFF: This function is turned off. When you disconnect the AC plug, the CHILD LOCK will be cancelled.
2 Press the 6 buttons and chose the favourite channel that you want to delete
3 Press the blue button The chosen favourite channel and set contents are deleted.
FEATURES menu

AUTO PROGRAM
EDIT/MANUAL LANGUAGE VIDEO-1 SETTING VIDEO-3 SETTING AI VOLUME TELETEXT LANGUAGE
AUTO PROGRAM
You can again perform the AUTO PROGRAM function TV channel automatic registration which was performed in the “Initial settings (Setup tour)” (page 8).
1 Choose AUTO PROGRAM, then press the a or 3 button The AUTO PROGRAM function starts. The TV channels you receive are automatically stored in the programme numbers list.
The EDIT/MANUAL functions are divided into two types:
2 After the TV channels have been stored in the programme number list, the EDIT menu appears

>> · 14%

DELETE: This function deletes a TV channel you do not want to list. MANUAL: This function manually stores a new TV channel in a programme number (PR). Caution
3 Press the a button to complete the settings
1 Press the 6 buttons to choose a TV channel
2 Press the 3 button to start the MOVE function
1 Choose EDIT/MANUAL, then press the a or 3 button The EDIT menu appears.

CH/CC PR ID AV 01 02 03 04 05 06 07 08 09

3 Press the 6 buttons to choose a new programme number (PR)
To cancel the MOVE function: Press the b button.
2 Follow the description for the function you want to use
4 Press the 2 button to change the programme number (PR) of a TV channel to a new programme number (PR)
SET UP menu · Basic operation

INSERT
1 Press the 6 buttons to choose a TV channel
1 Press the 6 buttons to choose a programme number (PR) for which you will register a new TV channel
2 Press the yellow button to delete the TV channel The TV channel is deleted from the programme numbers (PR) list.
2 Press the green button and start the INSERT function

CH/CC PR ID AV 01 02 03 04 05 06 07 08 09
21 22 23 24 25 26 CC CC CC
1 Press the 6 buttons to choose a TV channel
2 Press the red button to start the ID function
3 Enter a channel name (ID). Press the 6 buttons to choose a character. Press the 5 buttons to move the cursor
3 Press the 6 buttons to choose “CC” or “CH” according to the CH/ CC number of the TV channel

To cancel the INSERT function: Press the b button.
CH/CC PR ID AV 01 02 03 04 05 06 07 08 09
21 22 23 24 25 26 CC CC CC
4 Press the number buttons to enter the remaining CH/CC number The TV shifts to registration mode. When the registration is completed, the picture of the TV channel appears on the screen.
To cancel the ID function: Press the b button.
4 Press the a button to give a channel name to a TV channel
Before performing INSERT operation
SET UP menu

4 Press the green or red button to search for a TV channel Scanning stops when the TV finds a TV channel. Then the TV channel is displayed.
1 Press the 6 buttons to choose a programme number (PR) for a new TV channel
2 Press the blue button to activate the MANUAL function At the right side following the CH/CC number, the SYSTEM (sound system) of the TV channel appears.
5 Press the green or red button repeatedly until the TV channel you want appears
If the TV channel reception is poor: Press the blue or yellow button to fine- tune the TV channel.

CH/CC PR ID AV 01 02 03 04 05 06 07 08 09
If you cannot hear the normal sound even when the picture of the TV channel appears normally: The SYSTEM setting is wrong. Press the 3 button and choose a SYSTEM that has normal sound.
6 Press the a button and register the TV channel to a Programme number (PR) The normal EDIT menu is resumed.
To cancel the MANUAL function: Press the b button.
3 Press the 3 button to choose the SYSTEM (sound system) for a TV channel you want to register

Bahrain, Kuwait, Oman, Qatar, United Arab Emirates, Yemen, etc. Indonesia, Malaysia, Singapore, Thailand, India, etc.
China, Vietnam, etc. D/K Hong Kong, etc. I Islamic Republic of Iran, Lebanon, Saudi Arabia, etc. B/G
Russia, etc. D/K Czech Republic, Poland, etc. D/K Germany, Holland, Belgium, etc. B/G
UK, etc. I Oceania Australia, New Zealand, etc. B/G
Republic of South Africa, etc. I Nigeria, etc. B/G Egypt, Morocco, etc. B/G
SET UP menu

AI VOLUME
The LANGUAGE setting which was performed in the “Initial settings (Setup tour)” (page 8) can be changed.
You can prevent the sudden increase or decrease of sound that occurs when changing the channel to another channel.
ON: This function is turned on.
1 Choose LANGUAGE, then press the a or 3 button A sub-menu of the LANGUAGE function appears.
OFF: This function is turned off.

2 Press the 6 buttons to choose a language. Then press the a button
Set the VIDEO-1 SETTING or VIDEO-3 SETTING correctly according to the video signal input from the external device connected to the VIDEO-1 or VIDEO-3 terminal. If this setting is incorrect, images will not be displayed.
VIDEO: If a normal video signal (composite video signal) is input.
COMPONENT: If a Component video signal (Y, Cb/Pb, Cr/ Pr signals) is input.
SET UP menu

There are four types of teletext language groups. Set the teletext language group that corresponds to the language of the teletext programme that you want to watch.
1 Choose TELETEXT LANGUAGE, then press the a or 3 button

2 Press the 6 buttons to choose a group

GROUP-1 Turkish, Hungarian, English, German, French, Italian, Spanish, Portuguese, Greek, Swedish, Finnish
GROUP-2 Polish, Serbian, Croatian, Slovenian, Czech, Slovak, Rumanian, Hungarian, German, French, Italian, Swedish, Finnish
GROUP-3 Russian, Bulgarian, Lettish, Lithuanian, Estonian, Ukrainian, Serbian, Croatian, Slovenian, Czech, Slovak, English, German
GROUP-4 Arabic, Czech, Slovak. Hungarian, English, German, French, Italian, Spanish, Portuguese, Swedish, Finnish
3 Press the a button to complete the setting The menu disappears.
SET UP menu


This TV can be used as a computer screen.
Use a D-SUB cable to connect the TV’s PC IN terminal to the computer’s analogue RGB output terminal. If you want to listen to the sound from the computer, use an audio cable to connect the VIDEO-3 AUDIO L/R sound input terminal to the computer’s sound output terminal. When the sound from the computer is mono, connect to the VIDEO-3 AUDIO L terminal.
After starting the computer, press the 4 or 6 p buttons to choose “PC”
You can listen to the sound when the sound from the computer is connected to the VIDEO-3 AUDIO L/R sound input terminal.


* Only the above formats are supported. * Even with the above formats and at 60 Hz, some problems may be experienced depending on the quality of the synchronous signal. (Depending on the quality, some pictures may not be displayed properly.) * Apple Macintosh* computers are not supported. When a picture is not displayed Check the computer’s refresh rate and set it to 60 Hz. Refer to the computer’s instruction manual. Computers which cannot have their refresh rate set to 60 Hz cannot be used with this unit.
* Apple Macintosh is a registered trademark of Apple Computer, Inc.

Connect the equipment to the TV, making the correct rear panel and front panel connections. Before connecting anything:
1 VCR (composite signal) 2 VCR (S-VIDEO signal; Y/C) 3 VCR for recording (composite signal) 4 DVD player (composite signal) 5 DVD player (S-VIDEO signal; Y/C) 6 TV game (composite signal) 7 TV game (S-VIDEO signal; Y/C) 8 Headphones 9 Camcorder (composite signal/S-VIDEO signal; Y/C) 0 DVD player (component video signals; Y, Pb/Cb, Pr/Cr) - Video cable = Audio cable ~ S-VIDEO cable ! Component cable
Connecting the PC
For details, see “Connecting to the computer” on page 40.


Additional preparation

Connect the headphones with a stereo mini- jack (3.5 mm diameter) to the headphone jack.

TV output from the OUT terminal
The video/sound signal of a TV channel you are viewing is always output from the OUT terminal.
While referring to the audio equipment connection diagram, connect the audio equipment you want to the TV. You can use external front speakers to listen to the TV sound instead of the TV speakers.
Before connecting anything:

When you want to use the INSERT function on page 36, find the CH/CC number corresponding to the Channel number of the TV channel from this table. US: The US channel numbers are the channel numbers used in the United States, Philippines, etc. CCIR: The CCIR channel numbers are the channel numbers used in the Middle East, Southeast Asia, etc. OIRT: The OIRT channel numbers are the channel numbers used in Eastern Europe, Russia, Vietnam, etc. AUSTRALIA: The AUSTRALIA channel numbers are the channel numbers used in Australia, etc.
Channel US CCIR OIRT AUSTRALIA CH02 US-2 E2 R1 AU-0 CH03 US-3 E3 AU-1 CH04 US-4 E4 R2 AU-2 CH05 US-5 E5 R6 AU-6 CH06 US-6 E6 R7 AU-7 CH07 US-7 E7 R8 AU-8 CH08 US-8 E8 R9 AU-9 CH09 US-9 E9 CH10 US-10 E10 R10 AU-10 CH11 US-11 E11 R11 AU-11 CH12 US-12 E12 R12 CH13 US-13 CH14 US-14, W+29 CH15 US-15, W+30 CH16 US-16, W+31 CH17 US-17, W+32 CH18 US-18, W+33 CH19 US-19, W+34 CH20 US-20, W+35 CH21 US-21, W+36 E21 CH22 US-22, W+37 E22 CH23 US-23, W+38 E23 CH24 US-24, W+39 E24 CH25 US-25, W+40 E25 CH26 US-26, W+41 E26 CH27 US-27, W+42 E27 CH28 US-28, W+43 E28 CH29 US-29, W+44 E29 CH30 US-30, W+45 E30 CH31 US-31, W+46 E31 CH32 US-32, W+47 E32 CH33 US-33, W+48 E33 CH34 US-34, W+49 E34 CH35 US-35, W+50 E35 CH36 US-36, W+51 E36 CH37 US-37, W+52 E37 CH38 US-38, W+53 E38 CH39 US-39, W+54 E39 CH40 US-40, W+55 E40 CH41 US-41, W+56 E41 CH42 US-42, W+57 E42 CH43 US-43, W+58 E43 CH44 US-44, W+59 E44 CH45 US-45, W+60 E45 CH46 US-46, W+61 E46 CH47 US-47, W+62 E47 CH48 US-48, W+63 E48 CH49 US-49, W+64 E49 CH50 US-50, W+65 E50 CH51 US-51, W+66 E51 CH52 US-52, W+67 E52 CH53 US-53, W+68 E53 CH54 US-54, W+69 E54 CH55 US-55, W+70 E55 CH56 US-56, W+71 E56 CH57 US-57, W+72 E57 CH58 US-58, W+73 E58 CH59 US-59, W+74 E59 CH60 US-60, W+75 E60 CH61 US-61, W+76 E61 CH62 US-62, W+77 E62 CH63 US-63, W+78 E63 CH64 US-64, W+79 E64 CH65 US-65, W+80 E65 CH66 US-66, W+81 E66 CH67 US-67, W+82 E67 CH68 US-68, W+83 E68 CH69 US-69, W+84 E69
Channel US CCIR OIRT AUSTRALIA CC01 S-1 AU-5 CC02 S-2 CC03 S-3 CC04 S-4 CC05 S-5 CC06 S-6 AU-5A CC07 S-7 CC08 S-8 CC09 S-9 CC10 S-10 CC11 S-11 CC12 S-12 CC13 S-13 CC14 A S-14 CC15 B S-15 CC16 C S-16 CC17 D S-17 CC18 E S-18 CC19 F S-19 CC20 G S-20 CC21 H S-21 CC22 I S-22 CC23 J S-23 CC24 K S-24 CC25 L S-25 CC26 M S-26 CC27 N S-27 CC28 O S-28 CC29 P S-29 CC30 Q S-30 CC31 R S-31 CC32 S S-32 CC33 T S-33 CC34 U S-34 CC35 V S-35 CC36 W S-36 CC37 W+1 S-37 CC38 W+2 S-38 CC39 W+3 S-39 CC40 W+4 S-40 CC41 W+5 S-41 CC42 W+6 CC43 W+7 CC44 W+8 CC45 W+9 CC46 W+10 CC47 W+11 CC48 W+12 CC49 W+13 CC50 W+14 CC51 W+15 CC52 W+16 CC53 W+17 CC54 W+18 CC55 W+19 CC56 W+20 CC57 W+21 CC58 W+22 CC59 W+23 CC60 W+24 CC61 W+25 CC62 W+26 CC63 W+27 CC64 W+28 CC75 X CC76 Y R3 CC77 Z R4 AU-3 CC78 Z+1 R5 CC79 Z+2 AU-4 CC95 A-5 CC96 A-4 CC97 A-3 CC98 A-2 CC99 A-1

If a problem arises while you are using the TV, please read this troubleshooting guide carefully before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example, if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may think there is a problem with the TV itself.
If you cannot turn on the TV
– Have the TV and aerial been connected
properly? – Has the aerial cable been damaged? – Is the aerial pointing in the right
If you cannot turn off the TV
No picture or no sound
Poor picture

If the TV does not respond to the
Troubleshooting · Other issues · Poor sound

Model LT-Z32SX4B/LT-Z32SX4S Broadcasting systems B, G, I, D, K, K1, M Colour systems PAL, SECAM, NTSC 3.58/4.43 MHz Channels and frequencies VHF low channel (VL) = 46.25 to 168.25 MHz VHF high channel (VH) = 175.25 to 463.25 MHz UHF channel (U) = 471.25 to 863.25 MHz • Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11 to S20) and hyper band (S21 to S41). Sound-multiplex systems NICAM (B/G, I, D/K) system, A2 (B/G, D/K) system Languages displayed by teletext
Please see the table in the description “TELETEXT LANGUAGE” on page 39.
Teletext systems FLOF (Fastext), TOP, WST (World Standard System) Power requirements 110 - 240 V AC, 50/60 Hz Power consumption 161 W (Standby: 2.8 W) Screen size Viewable area 80 cm (measured diagonally) Audio output Rated Power output: 10 W + 10 W Speakers 6.6 cm round × 4 VIDEO-1 terminal (COMPONENT)
We may change the design and specifications without notice. Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as this would be an infringement of copyright.

Model LT-Z26SX4B/LT-Z26SX4S Broadcasting systems B, G, I, D, K, K1, M Colour systems PAL, SECAM, NTSC 3.58/4.43 MHz Channels and frequencies VHF low channel (VL) = 46.25 to 168.25 MHz VHF high channel (VH) = 175.25 to 463.25 MHz UHF channel (U) = 471.25 to 863.25 MHz • Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11 to S20) and hyper band (S21 to S41). Sound-multiplex systems NICAM (B/G, I, D/K) system, A2 (B/G, D/K) system Languages displayed by teletext
Please see the table in the description “TELETEXT LANGUAGE” on page 39.
Teletext systems FLOF (Fastext), TOP, WST (World Standard System) Power requirements 110 - 240 V AC, 50/60 Hz Power consumption 125 W (Standby: 2.8 W) Screen size Viewable area 64.8 cm (measured diagonally) Audio output Rated Power output: 10 W + 10 W Speakers 6.6 cm round × 4 VIDEO-1 terminal (COMPONENT)
We may change the design and specifications without notice. Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as this would be an infringement of copyright.
Specifications

© 2004 Victor Company of Japan, Limited 0904MKH-CR-MT
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.