EN
NETGEAR logo
Official user manual

NETGEAR DG834G

190 pages·4.8 MB·Network Router·PDF·ENDEFRITNLJA
NETGEAR DG834G
Table of Contents 133 sections Reference Manual for the ADSL Modem Wireless Router DG834G · Contents · Chapter 1 About This Manual · Audience, Scope, Conventions, and Formats · … ShowHide
Reference Manual for the ADSL Modem Wireless Router DG834Gp.1Contentsp.7Chapter 1 About This Manualp.13Audience, Scope, Conventions, and Formatsp.13How to Print this Manualp.14Chapter 2 Introductionp.17About the Modem Routerp.17Key Featuresp.18A Powerful, True Firewallp.18802.11 Standards-based Wireless Networkingp.19Easy Installation and Managementp.19Protocol Supportp.20Virtual Private Networking (VPN)p.21Auto Sensing and Auto Uplink™ LAN Ethernet Connectionsp.21Content Filteringp.22Trend Micro Home Network Securityp.22What’s in the Box?p.23The Router’s Front Panelp.24The Router’s Rear Panelp.25Connecting the Router to the Internetp.26Chapter 3 Wireless Configurationp.27Considerations for a Wireless Networkp.27Observe Performance, Placement, and Range Guidelinesp.27Implement Appropriate Wireless Securityp.28Understanding Wireless Settingsp.29How to Set Up and Test Basic Wireless Connectivityp.32How to Restrict Wireless Access to Your Networkp.33Choosing WEP Authentication and Security Encryption Methodsp.36How to Configure WEPp.38How to Configure WPA-PSKp.39How to Configure WPA-802.1xp.40Chapter 4 Protecting Your Networkp.41Protecting Access to Your 54 Mbps ADSL Modem Wireless Router Model DG834Gp.41How to Change the Built-In Passwordp.41Changing the Administrator Login Timeoutp.42Configuring Basic Firewall Servicesp.43Blocking Keywords, Sites, and Servicesp.43How to Block Keywords and Sitesp.43Firewall Rulesp.45Inbound Rules (Port Forwarding)p.46Outbound Rules (Service Blocking)p.49Order of Precedence for Rulesp.51Servicesp.52How to Define Servicesp.52Setting Times and Scheduling Firewall Servicesp.53How to Set Your Time Zonep.53How to Schedule Firewall Servicesp.55Trend Micro Home Network Securityp.55Security Service Settingsp.56Parental Controls Settingsp.58Chapter 5 Managing Your Networkp.63Backing Up, Restoring, or Erasing Your Settingsp.63How to Back Up the Configuration to a Filep.63How to Restore the Configuration from a Filep.64How to Erase the Configurationp.64Upgrading the Modem Router’s Firmwarep.64How to Upgrade the Modem Router Firmwarep.65Network Management Informationp.66Viewing Modem Router Status and Usage Statisticsp.66Viewing Attached Devicesp.71Viewing, Selecting, and Saving Logged Informationp.71Examples of Log Messagesp.74Enabling Security Event E-mail Notificationp.75Running Diagnostic Utilities and Rebooting the Modem Routerp.77Enabling Remote Managementp.78Configuring Remote Managementp.78Chapter 6 Advanced Configurationp.81Configuring Advanced Securityp.81Setting Up A Default DMZ Serverp.82Connect Automatically, as Requiredp.83Disable Port Scan and DOS Protectionp.83Respond to Ping on Internet WAN Portp.84MTU Sizep.84Configuring LAN IP Settingsp.84DHCPp.86How to Configure LAN TCP/IP Settingsp.88Configuring Dynamic DNSp.89How to Configure Dynamic DNSp.89Using Static Routesp.91Static Route Examplep.91How to Configure Static Routesp.92Universal Plug and Play (UPnP)p.93Chapter 7 Virtual Private Networkingp.95Overview of VPN Configurationp.96Client-to-Gateway VPN Tunnelsp.96Gateway-to-Gateway VPN Tunnelsp.97Planning a VPNp.98VPN Tunnel Configurationp.100How to Set Up a Client-to-Gateway VPN Configurationp.101Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v3p.101Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PCp.106How to Set Up a Gateway-to-Gateway VPN Configurationp.115VPN Tunnel Controlp.123Activating a VPN Tunnelp.123Verifying the Status of a VPN Tunnelp.127Deactivating a VPN Tunnelp.129Deleting a VPN Tunnelp.131How to Set Up VPN Tunnels in Special Circumstancesp.132Using Auto Policy to Configure VPN Tunnelsp.132Using Manual Policy to Configure VPN Tunnelsp.142Chapter 8 Troubleshootingp.145Basic Functioningp.145Power LED Not Onp.146Test LED Never Turns On or Test LED Stays Onp.146LAN or Internet Port LEDs Not Onp.146Troubleshooting the Web Configuration Interfacep.147Troubleshooting the ISP Connectionp.148ADSL linkp.148Obtaining a WAN IP Addressp.149Troubleshooting PPPoE or PPPoAp.150Troubleshooting Internet Browsingp.151Troubleshooting a TCP/IP Network Using the Ping Utilityp.151Testing the LAN Path to Your Routerp.151Testing the Path from Your Computer to a Remote Devicep.152Restoring the Default Configuration and Passwordp.153Using the Reset buttonp.153Problems with Date and Timep.153Appendix A Technical Specificationsp.155Appendix B NETGEAR VPN Configurationp.157DG834G v3 to FVL328p.157Configuration Profilep.157Step-By-Step Configurationp.158DG834G v3 with FQDN to FVL328p.162Configuration Profilep.162Step-By-Step Configurationp.164Configuration Summary (Telecommuter Example)p.170Setting Up the Client-to-Gateway VPN Configuration (Telecommuter Example)p.170Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Officep.171Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Officep.174Monitoring the VPN Tunnel (Telecommuter Example)p.184Viewing the PC Client’s Connection Monitor and Log Viewerp.184Viewing the VPN Router’s VPN Status and Log Informationp.185Appendix C Related Documentsp.189
Page 1 of the NETGEAR DG834G user manual — Reference Manual for the ADSL Modem Wireless Router DG834G
Page 1 · click to enlarge
Page 1

NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA

202-10155-01 October 2006

Page 2 of the NETGEAR DG834G user manual — Reference Manual for the ADSL Modem Wireless Router DG834G
Page 2 · click to enlarge
Page 2

© 2006 by NETGEAR, Inc. All rights reserved.

NETGEAR is a trademark of Netgear, Inc.

Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.

Other brand and product names are registered trademarks or trademarks of their respective holders.

In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.

NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Federal Communications Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.

Trademarks · Statement of Conditions

Page 3 of the NETGEAR DG834G user manual — European Union Statement of Compliance
Page 3 · click to enlarge
Page 3

European Union Statement of Compliance

Hereby, NETGEAR, Inc. declares that this modem router is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Èesky [Czech]NETGEAR, Inc. tímto prohlašuje, že tento 54 Mbps ADSL Modem Wireless Router Model DG834G je ve shodì se základními požadavky a dalšími pøíslušnými ustanoveními smìrnice 1999/5/ES. Dansk [Danish]Undertegnede NETGEAR, Inc. erklærer herved, at følgende udstyr 54 Mbps ADSL Modem Wireless Router Model DG834G overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German]Hiermit erklärt NETGEAR, Inc., dass sich das Gerät 54 Mbps ADSL Modem Wireless Router Model DG834G in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian]Käesolevaga kinnitab NETGEAR, Inc. seadme 54 Mbps ADSL Modem Wireless Router Model DG834G vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. EnglishHereby, NETGEAR, Inc., declares that this 54 Mbps ADSL Modem Wireless Router Model DG834G is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish]Por medio de la presente NETGEAR, Inc. declara que el 54 Mbps ADSL Modem Wireless Router Model DG834G cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek]ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ NETGEAR, Inc. ΔΗΛΩΝΕΙ ΟΤΙ 54 Mbps ADSL Modem Wireless Router Model DG834G ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Français [French]Par la présente NETGEAR, Inc. déclare que l'appareil 54 Mbps ADSL Modem Wireless Router Model DG834G est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian]Con la presente NETGEAR, Inc. dichiara che questo 54 Mbps ADSL Modem Wireless Router Model DG834G è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian]Ar šo NETGEAR, Inc. deklarç, ka 54 Mbps ADSL Modem Wireless Router Model DG834G atbilst Direktîvas 1999/5/EK bûtiskajâm prasîbâm un citiem ar to saistîtajiem noteikumiem. Lietuviø [Lithuanian]Šiuo NETGEAR, Inc. deklaruoja, kad šis 54 Mbps ADSL Modem Wireless Router Model DG834G atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Page 4 of the NETGEAR DG834G user manual — Reference Manual for the ADSL Modem Wireless Router DG834G
Page 4 · click to enlarge
Page 4
Nederlands [Dutch]Hierbij verklaart NETGEAR, Inc. dat het toestel 54 Mbps ADSL Modem Wireless Router Model DG834G in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese]Hawnhekk, NETGEAR, Inc., jiddikjara li dan 54 Mbps ADSL Modem Wireless Router Model DG834G jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian]Alulírott, NETGEAR, Inc. nyilatkozom, hogy a 54 Mbps ADSL Modem Wireless Router Model DG834G megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish]Niniejszym NETGEAR, Inc. oœwiadcza, ¿e 54 Mbps ADSL Modem Wireless Router Model DG834G jest zgodny z zasadniczymi wymogami oraz pozosta³ymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese]NETGEAR, Inc. declara que este 54 Mbps ADSL Modem Wireless Router Model DG834G está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian]NETGEAR, Inc. izjavlja, da je ta 54 Mbps ADSL Modem Wireless Router Model DG834G v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloèili direktive 1999/5/ ES. Slovensky [Slovak]NETGEAR, Inc. týmto vyhlasuje, že 54 Mbps ADSL Modem Wireless Router Model DG834G spåòa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ ES. Suomi [Finnish]NETGEAR, Inc. vakuuttaa täten että 54 Mbps ADSL Modem Wireless Router Model DG834G tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish]Härmed intygar NETGEAR, Inc. att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

A printed copy of the EU Declaration of Conformity certificate for this product is provided in the DG834G v3 product package.

Es wird hiermit bestätigt, daß das 54 Mbps ADSL Modem Wireless Router Model DG834G gemäß der im BMPT- AmtsblVfg 243/1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.B. Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung.

Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.

Bestätigung des Herstellers/Importeurs

Page 5 of the NETGEAR DG834G user manual — Reference Manual for the ADSL Modem Wireless Router DG834G
Page 5 · click to enlarge
Page 5

Certificate of the Manufacturer/Importer

It is hereby certified that the 54 Mbps ADSL Modem Wireless Router Model DG834G has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions.

Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations.

Voluntary Control Council for Interference (VCCI) Statement

This equipment is in the second category (information equipment to be used in a residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas.

When used near a radio or TV receiver, it may become the cause of radio interference.

Read instructions for correct handling.

Refer to the Support Information Card that shipped with your 54 Mbps ADSL Modem Wireless Router Model DG834G.

NETGEAR maintains a World Wide Web home page that you can access at the universal resource locator (URL) http://www.netgear.com. A direct connection to the Internet and a Web browser such as Internet Explorer or Netscape are required.

Customer Support · World Wide Web

Page 6 of the NETGEAR DG834G user manual — Reference Manual for the ADSL Modem Wireless Router DG834G
Page 6 · click to enlarge
Page 6

Product and Publication Details

Model NumberDG834G v3
Publication DateOctober 2006
Product FamilyModem Router
Product Name54 Mbps ADSL Modem Wireless Router Model DG834G
Home or Business ProductHome
LanguageEnglish
Publication Part Number202-10155-01
Publication Version Number1.0
VersionDate PublishedChange Description 1.0January 2006Original publication 1.1October 2006Removed NETBIOS feature.

Change History

Page 7 of the NETGEAR DG834G user manual — Table of Contents
Page 7 · Contents
Contents

Contents

Reference Manual for the ADSL Modem Wireless Router DG834Gp.1Contentsp.7Chapter 1 About This Manualp.13Audience, Scope, Conventions, and Formatsp.13How to Print this Manualp.14Chapter 2 Introductionp.17About the Modem Routerp.17Key Featuresp.18A Powerful, True Firewallp.18802.11 Standards-based Wireless Networkingp.19Easy Installation and Managementp.19Protocol Supportp.20Virtual Private Networking (VPN)p.21Auto Sensing and Auto Uplink™ LAN Ethernet Connectionsp.21Content Filteringp.22Trend Micro Home Network Securityp.22What’s in the Box?p.23The Router’s Front Panelp.24The Router’s Rear Panelp.25Connecting the Router to the Internetp.26Chapter 3 Wireless Configurationp.27Considerations for a Wireless Networkp.27Observe Performance, Placement, and Range Guidelinesp.27Implement Appropriate Wireless Securityp.28Understanding Wireless Settingsp.29How to Set Up and Test Basic Wireless Connectivityp.32How to Restrict Wireless Access to Your Networkp.33Choosing WEP Authentication and Security Encryption Methodsp.36How to Configure WEPp.38How to Configure WPA-PSKp.39How to Configure WPA-802.1xp.40Chapter 4 Protecting Your Networkp.41Protecting Access to Your 54 Mbps ADSL Modem Wireless Router Model DG834Gp.41How to Change the Built-In Passwordp.41Changing the Administrator Login Timeoutp.42Configuring Basic Firewall Servicesp.43Blocking Keywords, Sites, and Servicesp.43How to Block Keywords and Sitesp.43Firewall Rulesp.45Inbound Rules (Port Forwarding)p.46Outbound Rules (Service Blocking)p.49Order of Precedence for Rulesp.51Servicesp.52How to Define Servicesp.52Setting Times and Scheduling Firewall Servicesp.53How to Set Your Time Zonep.53How to Schedule Firewall Servicesp.55Trend Micro Home Network Securityp.55Security Service Settingsp.56Parental Controls Settingsp.58Chapter 5 Managing Your Networkp.63Backing Up, Restoring, or Erasing Your Settingsp.63How to Back Up the Configuration to a Filep.63How to Restore the Configuration from a Filep.64How to Erase the Configurationp.64Upgrading the Modem Router’s Firmwarep.64How to Upgrade the Modem Router Firmwarep.65Network Management Informationp.66Viewing Modem Router Status and Usage Statisticsp.66Viewing Attached Devicesp.71Viewing, Selecting, and Saving Logged Informationp.71Examples of Log Messagesp.74Enabling Security Event E-mail Notificationp.75Running Diagnostic Utilities and Rebooting the Modem Routerp.77Enabling Remote Managementp.78Configuring Remote Managementp.78Chapter 6 Advanced Configurationp.81Configuring Advanced Securityp.81Setting Up A Default DMZ Serverp.82Connect Automatically, as Requiredp.83Disable Port Scan and DOS Protectionp.83Respond to Ping on Internet WAN Portp.84MTU Sizep.84Configuring LAN IP Settingsp.84DHCPp.86How to Configure LAN TCP/IP Settingsp.88Configuring Dynamic DNSp.89How to Configure Dynamic DNSp.89Using Static Routesp.91Static Route Examplep.91How to Configure Static Routesp.92Universal Plug and Play (UPnP)p.93Chapter 7 Virtual Private Networkingp.95Overview of VPN Configurationp.96Client-to-Gateway VPN Tunnelsp.96Gateway-to-Gateway VPN Tunnelsp.97Planning a VPNp.98VPN Tunnel Configurationp.100How to Set Up a Client-to-Gateway VPN Configurationp.101Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v3p.101Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PCp.106How to Set Up a Gateway-to-Gateway VPN Configurationp.115VPN Tunnel Controlp.123Activating a VPN Tunnelp.123Verifying the Status of a VPN Tunnelp.127Deactivating a VPN Tunnelp.129Deleting a VPN Tunnelp.131How to Set Up VPN Tunnels in Special Circumstancesp.132Using Auto Policy to Configure VPN Tunnelsp.132Using Manual Policy to Configure VPN Tunnelsp.142Chapter 8 Troubleshootingp.145Basic Functioningp.145Power LED Not Onp.146Test LED Never Turns On or Test LED Stays Onp.146LAN or Internet Port LEDs Not Onp.146Troubleshooting the Web Configuration Interfacep.147Troubleshooting the ISP Connectionp.148ADSL linkp.148Obtaining a WAN IP Addressp.149Troubleshooting PPPoE or PPPoAp.150Troubleshooting Internet Browsingp.151Troubleshooting a TCP/IP Network Using the Ping Utilityp.151Testing the LAN Path to Your Routerp.151Testing the Path from Your Computer to a Remote Devicep.152Restoring the Default Configuration and Passwordp.153Using the Reset buttonp.153Problems with Date and Timep.153Appendix A Technical Specificationsp.155Appendix B NETGEAR VPN Configurationp.157DG834G v3 to FVL328p.157Configuration Profilep.157Step-By-Step Configurationp.158DG834G v3 with FQDN to FVL328p.162Configuration Profilep.162Step-By-Step Configurationp.164Configuration Summary (Telecommuter Example)p.170Setting Up the Client-to-Gateway VPN Configuration (Telecommuter Example)p.170Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Officep.171Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Officep.174Monitoring the VPN Tunnel (Telecommuter Example)p.184Viewing the PC Client’s Connection Monitor and Log Viewerp.184Viewing the VPN Router’s VPN Status and Log Informationp.185Appendix C Related Documentsp.189
Page 13 of the NETGEAR DG834G user manual — Audience, Scope, Conventions, and Formats
Page 13 · click to enlarge
Page 13

Chapter 1 About This Manual

This chapter describes the intended audience, scope, conventions, and formats of this manual.

Audience, Scope, Conventions, and Formats

This reference manual assumes that the reader has basic to intermediate computer and Internet skills. However, basic computer network, Internet, firewall, and VPN technologies tutorial information is provided in the Appendices and on the Netgear website.

http://kbserver.netgear.com/products/DG834G v3.asp.

This guide uses the following typographical conventions:

Table 1-1.

italics Emphasis, books, CDs, URL names

fixed Screen text, file and server names, extensions, commands, IP addresses

This guide uses the following formats to highlight special messages:

About This Manual 1-1

bold User input

Page 14 of the NETGEAR DG834G user manual — How to Print this Manual
Page 14 · click to enlarge
Page 14

equipment.

personal injury or death.

This manual is written for the ADSL Modem Wireless Router according to these specifications:

Table 1-2. Manual Scope

Product Version 54 Mbps ADSL Modem Wireless Router Model DG834G

Manual Publication Date October 2006

How to Print this Manual

To print this manual you can choose one of the following several options, according to your needs.

  • Printing a Page in the HTML View .

Each page in the HTML version of the manual is dedicated to a major topic. Use the Print button on the browser toolbar to print the page contents.

  • Printing a Chapter .

Use the PDF of This Chapter link at the top left of any page.

— Click the PDF of This Chapter link at the top right of any page in the chapter you want to

print. The PDF version of the chapter you were viewing opens in a browser window.

— Your computer must have the free Adobe Acrobat reader installed in order to view and

print PDF files. The Acrobat reader is available on the Adobe Web site at http://www.adobe.com.

1-2 About This Manual

Page 15 of the NETGEAR DG834G user manual — How to Print this Manual
Page 15 · click to enlarge
Page 15

— Click the print icon in the upper left of the window.

save paper and printer ink by selecting this feature.

  • Printing the Full Manual .

Use the Complete PDF Manual link at the top left of any page.

— Click the Complete PDF Manual link at the top left of any page in the manual. The PDF

version of the complete manual opens in a browser window.

— Click the print icon in the upper left of the window.

save paper and printer ink by selecting this feature.

About This Manual 1-3

Page 16 of the NETGEAR DG834G user manual — How to Print this Manual
Page 16 · click to enlarge
Page 16

1-4 About This Manual

Page 17 of the NETGEAR DG834G user manual — About the Modem Router
Page 17 · click to enlarge
Page 17

Chapter 2 Introduction

This chapter describes the features of the NETGEAR 54 Mbps ADSL Modem Wireless Router Model DG834G. The ADSL Modem Wireless Router is a combination of a built-in ADSL modem, modem router, 4-port switch, and firewall which enables your entire network to safely share an Internet connection that otherwise would be used by a single computer.

and TCP/IP Addressing” in Appendix C to become more familiar with the terms and procedures used in this manual.

About the Modem Router

The 54 Mbps ADSL Modem Wireless Router Model DG834G provides continuous, high-speed 10/100 Ethernet access between your Ethernet devices. With minimum setup, you can install and use the modem router within minutes.

The ADSL Modem Wireless Router provides multiple Web content filtering options, reporting, and instant alerts. Parents and network administrators can establish restricted access policies based on time of day, Web site addresses, and address keywords. They can also share high-speed ADSL Internet access for up to 253 personal computers. The included firewall and Network Address Translation (NAT) features protect you from hackers.

The DG834G v3 also supports Trend Micro Home Network Security, a bundle of services that includes router-based Parental Controls and network-wide protection from viruses, Trojans, spyware, spam, and other Internet threats.

Introduction 2-1

Page 18 of the NETGEAR DG834G user manual — A Powerful, True Firewall
Page 18 · click to enlarge
Page 18

Key Features

The ADSL Modem Wireless Router provides the following features:

  • A built-in ADSL modem
  • A powerful, true firewall
  • 802.11g standards-based wireless networking
  • Easy, Web-based setup for installation and management
  • Extensive Internet protocol support
  • Trustworthy VPN Communications over the Internet
  • VPN Wizard for easy VPN configuration
  • Auto Sensing and Auto Uplink™ LAN Ethernet connections
  • Content filtering
  • Support for Trend Micro Home Network Security

These features are discussed below.

A Powerful, True Firewall

Unlike simple Internet sharing NAT routers, the DG834G v3 is a true firewall, using stateful packet inspection to defend against hacker attacks. Its firewall features include:

  • Denial of Service (DoS) protection Automatically detects and thwarts Denial of Service (DoS) attacks such as Ping of Death, SYN Flood, LAND Attack and IP Spoofing.
  • Blocks unwanted traffic from the Internet to your LAN.
  • Blocks access from your LAN to Internet locations or services that you specify as off-limits.
  • Logs security incidents The DG834G v3 will log security events such as blocked incoming traffic, port scans, attacks, and administrator logins. You can configure the modem router to email the log to you at specified intervals. You can also configure the modem router to send immediate alert messages to your email address or email pager whenever a significant event occurs.

2-2 Introduction

Page 19 of the NETGEAR DG834G user manual — Easy Installation and Management
Page 19 · click to enlarge
Page 19

802.11 Standards-based Wireless Networking

The ADSL Modem Wireless Router includes an 802.11g-compliant wireless access point, providing continuous, high-speed 10/100 Mbps access between your wireless and Ethernet devices. The access point provides:

  • 802.11g Standards-based wireless networking at up to 54 Mbps
  • Works with both 802.11g and 802.11b wireless devices
  • 64-bit and 128-bit WEP encryption security
  • WEP keys can be entered manually or generated by passphrase
  • Support for Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) encryption and 802.1x authentication
  • Wireless access can be restricted by MAC address

Easy Installation and Management

You can install, configure, and operate the DG834G v3 within minutes after connecting it to the network. The following features simplify installation and management tasks:

  • Browser-based management Browser-based configuration allows you to easily configure your modem router from almost any type of personal computer, such as Windows, Macintosh, or Linux. A user-friendly Setup Wizard is provided and online help documentation is built into the browser-based Web Management Interface.
  • Smart Wizard The firmware in the modem router automatically senses the type of Internet connection, asking you only for the information required for your type of ISP account.
  • Remote management The modem router allows you to log in to the Web management interface from a remote location via the Internet. For security, you can limit remote management access to a specified remote IP address or range of addresses, or you can choose a nonstandard port number.
  • Diagnostic functions The modem router incorporates built-in diagnostic functions such as Ping, DNS lookup, and remote reboot. These functions allow you to test Internet connectivity and reboot the modem router. You can use these diagnostic functions directly from the DG834G v3 when you are connected on the LAN or when you are connected over the Internet via the remote management function.

Introduction 2-3

Page 20 of the NETGEAR DG834G user manual — Protocol Support
Page 20 · click to enlarge
Page 20
  • Visual monitoring The modem router’s front panel LEDs provide an easy way to monitor its status and activity.
  • Flash erasable programmable read-only memory (EPROM) for firmware upgrades.

Protocol Support

The DG834G v3 supports Transmission Control Protocol/Internet Protocol (TCP/IP) and Routing Information Protocol (RIP). “Internet Networking and TCP/IP Addressing” in Appendix C provides further information on TCP/IP.

  • The Ability to Enable or Disable IP Address Sharing by NAT The DG834G v3 allows several networked PCs to share an Internet account using only a single IP address, which may be statically or dynamically assigned by your Internet service provider (ISP). This technique, known as Network Address Translation (NAT), allows the use of an inexpensive single-user ISP account. This feature can also be turned off completely while using the DG834G v3 if you want to manage the IP address scheme yourself.
  • Automatic Configuration of Attached PCs by DHCP The DG834G v3 dynamically assigns network configuration information, including IP, modem router, and domain name server (DNS) addresses, to attached PCs on the LAN using the Dynamic Host Configuration Protocol (DHCP). This feature greatly simplifies configuration of PCs on your local network.
  • DNS Proxy When DHCP is enabled and no DNS addresses are specified, the modem router provides its own address as a DNS server to the attached PCs. The modem router obtains actual DNS addresses from the ISP during connection setup and forwards DNS requests from the LAN.
  • Classical IP (RFC 1577) Some Internet service providers, in Europe for example, use Classical IP in their ADSL services. In such cases, the modem router is able to use the Classical IP address from the ISP.
  • PPP over Ethernet (PPPoE) PPP over Ethernet is a protocol for connecting remote hosts to the Internet over an ADSL connection by simulating a dial-up connection. This feature eliminates the need to run a login program such as EnterNet or WinPOET on your computer.
  • PPP over ATM (PPPoA) PPP over ATM is a protocol for connecting remote hosts to the Internet over an ADSL connection by simulating an ATM connection.

2-4 Introduction

Page 21 of the NETGEAR DG834G user manual — Auto Sensing and Auto Uplink™ LAN Ethernet Connections
Page 21 · click to enlarge
Page 21
  • Dynamic DNS Dynamic DNS services allow remote users to find your network using a domain name when your IP address is not permanently assigned. The modem router contains a client that can connect to many popular Dynamic DNS services to register your dynamic IP address.
  • Universal Plug and Play (UPnP) UPnP is a networking architecture that provides compatibility between networking technologies. UPnP compliant routers provide broadband users at home and small businesses with a seamless way to participate in online games, videoconferencing and other peer-to-peer services.

Virtual Private Networking (VPN)

The ADSL Modem Wireless Router provides a secure encrypted connection between your local area network (LAN) and remote networks or clients. It includes the following VPN features:

  • Supports 5 VPN connections.
  • Supports industry standard VPN protocols The ADSL Modem Wireless Router supports standard Manual or IKE keying methods, standard MD5 and SHA-1 authentication methods, and standard DES and 3DES encryption methods. It is compatible with many other VPN products.
  • Supports 3DES encryption for maximum security.
  • VPN Wizard based on VPNC recommended settings.

Auto Sensing and Auto Uplink™ LAN Ethernet Connections

With its internal 4-port 10/100 switch, the DG834G v3 can connect to either a 10 Mbps standard Ethernet network or a 100 Mbps Fast Ethernet network. The local LAN ports are autosensing and capable of full-duplex or half-duplex operation.

The modem router incorporates Auto UplinkTM technology. Each local Ethernet port will automatically sense whether the Ethernet cable plugged into the port should have a ‘normal’ connection such as to a computer or an ‘uplink’ connection such as to a switch or hub. That port will then configure itself to the correct configuration. This feature also eliminates the need to worry about crossover cables, as Auto Uplink will accommodate either type of cable to make the right connection.

Introduction 2-5

Page 22 of the NETGEAR DG834G user manual — Trend Micro Home Network Security
Page 22 · click to enlarge
Page 22

Content Filtering

With its content filtering feature, the DG834G v3 prevents objectionable content from reaching your PCs. The modem router allows you to control access to Internet content by screening for keywords within Web addresses. You can configure the modem router to log and report attempts to access objectionable Internet sites.

Trend Micro Home Network Security

This service bundle from Trend Micro has three components:

  • Trend Micro dashboard This component is free for unlimited use. From the dashboard you can: — Scan your computer and entire network for security vulnerabilities — View individual computer and network-wide security reports — Detect and remove spyware — View attempts to access content restricted by Parental Controls — Purchase subscriptions for Parental Controls and Trend Micro Internet Security
  • Trend Micro Internet Security You can install this program on up to 10 computers and try it free for 60 days. Its features include: — Real-time and scheduled scanning to remove viruses, Trojans, spyware, and other Internet

threats — Personal firewall — Network intruder detection — Anti-spam

  • Router-based Parental Controls This service restricts home network users from viewing inappropriate Web content. It is free for 60 days, and when you register your free trial of Trend Micro Internet Security, your free use of Parental Controls is automatically extended to one year.

For instructions on activating these services, refer to “Trend Micro Home Network Security” on page 4-15.

2-6 Introduction

Page 23 of the NETGEAR DG834G user manual — What’s in the Box?
Page 23 · click to enlarge
Page 23

What’s in the Box?

The product package should contain the following items:

  • 54 Mbps ADSL Modem Wireless Router Model DG834G
  • AC power adapter (varies by region)
  • Category 5 (Cat 5) Ethernet cable
  • Telephone cable with RJ-11 connector
  • Microfilters (quantity and type vary by region)
  • DG834G ADSL Modem Wireless Router Resource CD , including this guide
  • Two plastic feet that can be used to stand the ADSL Modem Wireless Router on end
  • Warranty and Support Information cards

If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the carton, including the original packing materials, in case you need to return the product for repair.

Introduction 2-7

Page 24 of the NETGEAR DG834G user manual — 5. LAN
Page 24 · click to enlarge
Page 24

The Router’s Front Panel The front panel shown below contains status LEDs.

NETGEAR DG834G — The Router’s Front Panel diagram (page 24)
Fig. 1 · The Router’s Front Panel
NETGEAR DG834G — The Router’s Front Panel diagram (page 24)
Fig. 2 · The Router’s Front Panel

1 2 3 4 5

You can use the LEDs to verify various conditions. Table 2-1 describes each LED.

Table 2-1. LED Descriptions

1. Power On Off

Power is supplied to the router. Power is not supplied to the router.

2. Test On Off

The system is initializing. The system is ready and running.

3. Internet Blink -- Amber On -- Green Blink -- Green

Indicates ADSL training. The Internet port has detected a link with an attached device. Data is being transmitted or received by the Internet port.

4. Wireless On Off

Indicates that the Wireless port is initialized. The Wireless Access Point is turned off.

On (Green) Blink (Green) On (Amber) Blink (Amber) Off

The Local port has detected a link with a 100 Mbps device. Data is being transmitted or received at 100 Mbps. The Local port has detected a link with a 10 Mbps device. Data is being transmitted or received at 10 Mbps. No link is detected on this port.

5. LAN

Label Activity Description · 2-8 Introduction

Page 25 of the NETGEAR DG834G user manual — The Router’s Rear Panel
Page 25 · click to enlarge
Page 25

The Router’s Rear Panel

The rear panel of the 54 Mbps ADSL Modem Wireless Router Model DG834G (Figure 2-2) contains port connections.

NETGEAR DG834G — The Router’s Rear Panel diagram (page 25)
Fig. 3 · The Router’s Rear Panel

Viewed from left to right, the rear panel contains the following elements:

1. RJ-11 ADSL port for connecting the firewall to an ADSL line
2. Four Local Ethernet RJ-45 LAN ports for connecting the firewall to the local computers
3. Factory Default Reset push button
4. AC power adapter outlet
5. Wireless antenna

Introduction 2-9

Page 26 of the NETGEAR DG834G user manual — Connecting the Router to the Internet
Page 26 · click to enlarge
Page 26

Connecting the Router to the Internet

To connect your ADSL Modem Wireless Router to the Internet, refer to the ADSL Modem Wirelesss Router Setup Manual on the DG834G ADSL Modem Wireless Router Resource CD or online as shown in the following table.

Table 2-2.

Dutch http://documentation.netgear.com/dg834g/nld/208-10039-01/

English http://documentation.netgear.com/dg834g/enu/208-10033-01/

French http://documentation.netgear.com/dg834g/fra/208-10034-01/

German http://documentation.netgear.com/dg834g/deu/208-10035-01/

Italian http://documentation.netgear.com/dg834g/ita/208-10036-01/

Spanish http://documentation.netgear.com/dg834g/esp/208-10037-01/

Swedish http://documentation.netgear.com/dg834g/sve/208-10038-01/

Language URL · 2-10 Introduction

Page 27 of the NETGEAR DG834G user manual — Observe Performance, Placement, and Range Guidelines
Page 27 · click to enlarge
Page 27

Chapter 3 Wireless Configuration

This chapter describes how to configure the wireless features of your 54 Mbps ADSL Modem Wireless Router Model DG834G.

Considerations for a Wireless Network

In planning your wireless network, you should consider the level of security required. You should also select the physical placement of your modem router in order to maximize the network speed.

To ensure proper compliance and compatibility between similar products in your area, the operating channel and region must be set correctly.

Observe Performance, Placement, and Range Guidelines

The operating distance or range of your wireless connection can vary significantly based on the physical placement of the wireless firewall. The latency, data throughput performance, and notebook power consumption also vary depending on your configuration choices.

or inability to wirelessly connect to the router. For complete range/performance specifications, please see Appendix A, “Technical Specifications”.

For best results, place your firewall:

  • Near the center of the area in which your computers will operate
  • In an elevated location such as a high shelf where the wirelessly connected computers have line-of-sight access (even if through walls)
  • Away from sources of interference, such as computers, microwaves, and cordless phones
  • With the Antenna tight and in the upright position
  • Away from large metal surfaces

Wireless Configuration 3-1

Page 28 of the NETGEAR DG834G user manual — Implement Appropriate Wireless Security
Page 28 · click to enlarge
Page 28

The time it takes to establish a wireless connection can vary depending on both your security settings and placement. WEP connections can take slightly longer to establish. Also, WEP encryption can consume more battery power on a notebook computer.

Implement Appropriate Wireless Security

range of up to 300 feet. Such distances can allow for others outside of your immediate area to access your network.

Unlike wired network data, your wireless data transmissions can extend beyond your walls and can be received by anyone with a compatible adapter. For this reason, use the security features of your wireless equipment. The ADSL Modem Wireless Router provides highly effective security features which are covered in detail in this chapter. Deploy the security features appropriate to your needs.

NETGEAR DG834G — Implement Appropriate Wireless Security diagram (page 28)
Fig. 4 · Implement Appropriate Wireless Security

There are several ways you can enhance the security of your wireless network:

  • Restrict Access Based on MAC Address. You can allow only trusted PCs to connect so that unknown PCs cannot wirelessly connect to the DG834G v3. Restricting access by MAC address adds an obstacle against unwanted access to your network, but the data broadcast over the wireless link is fully exposed.
  • Turn Off the Broadcast of the Wireless Network Name SSID. If you disable broadcast of the SSID, only devices that have the correct SSID can connect. This nullifies wireless network ‘discovery’ feature of some products, such as Windows XP, but the data is still exposed.

3-2 Wireless Configuration

Page 29 of the NETGEAR DG834G user manual — Understanding Wireless Settings
Page 29 · click to enlarge
Page 29
  • WEP. Wired Equivalent Privacy (WEP) data encryption provides data security. WEP Shared Key authentication and WEP data encryption will block all but the most determined eavesdropper.
  • WPA . Wi-Fi Protected Access (WPA) data encryption provides data security. The very strong authentication along with dynamic per frame re-keying of WPA make it virtually impossible to compromise. Because this is a new standard, wireless device driver and software availability may be limited.

Understanding Wireless Settings

To configure the Wireless interface of your modem router, click the Wireless Settings link in the Setup section of the main menu. The Wireless Settings menu will appear, similar to that shown below:

NETGEAR DG834G — Understanding Wireless Settings diagram (page 29)
Fig. 5 · Understanding Wireless Settings

Wireless Configuration 3-3

Page 30 of the NETGEAR DG834G user manual — Understanding Wireless Settings
Page 30 · click to enlarge
Page 30

The following parameters are in the Wireless Settings menu:

  • Wireless Network .

— Name (SSID). The Service Set ID, also known as the wireless network name. Enter a

value of up to 32 alphanumeric characters. The same Name (SSID) must be assigned to all wireless devices in your network. The default SSID is NETGEAR, but NETGEAR strongly recommends that you change your network Name to a different value.

wireless.

— Region. Select your country/region from the drop-down list. This field displays the region

of operation for which the wireless interface is intended.

cannot be changed. In other areas, you can and must set the Region. It may not be legal to operate the wireless access point in a region other than one of those identified in this field.

— Channel. This field determines which operating frequency will be used. It should not be

necessary to change the wireless channel unless you notice interference problems with another nearby access point.

— Mode. The default is "g & b", which allows both "g" and "b" wireless stations to access

this device. “g only” allows only 802.11g wireless stations to be used. “b only” allows 802.11b wireless stations; 802.11g wireless stations can still be used if they can operate in 802.11b mode.

  • Wireless Access Point .

— Enable Wireless Access Point. This field lets you turn off or turn on the wireless access

point built in to the modem router. The wireless icon on the front of the modem router will also display the current status of the Wireless Access Point to let you know if it is disabled or enabled. The wireless access point must be enabled to allow wireless stations to access the Internet.

— Allow Broadcast of Name (SSID). If enabled, the SSID is broadcast to all Wireless

Stations. Stations which have no SSID (or a "null" value) can then adopt the correct SSID for connections to this Access Point.

3-4 Wireless Configuration

Page 31 of the NETGEAR DG834G user manual — Understanding Wireless Settings
Page 31 · click to enlarge
Page 31

— Wireless Isolation. If enabled, Wireless Stations will not be able to communicate with

each other or with Stations on the wired network. This feature should normally be disabled.

  • Wireless Station Access List .

— By default, any wireless computer that is configured with the correct wireless network

name or SSID will be allowed access to your wireless network. For increased security, you can restrict access to the wireless network to only specific computers based on their MAC addresses. Click Setup Access List to display the Wireless Station Access List menu.

  • Security Options

Table 3-1. Wireless Security Options

Disable Wireless security is not used.

WEP (Wired Equivalent Privacy)

You can select the following WEP options:

  • Authentication Type
  • Open: the DG834G v3 does not perform any authentication.
  • Shared: WEP shared key authentication. For a full explanation of WEP shared key, see “Wireless Communications” in Appendix C .

Encryption Strength • If Shared or Open Network Authentication is enabled, you can choose 64- or 128-bit WEP data encryption. Note: With Open Network Authentication and 64- or 128-bit WEP Data Encryption, the DG834G v3 does perform 64- or 128-bit data encryption but does not perform any authentication.

  • Security Encryption (WEP) Key These key values must be identical on all wireless devices in your network (key 1 must be the same for all, key 2 must be the same for all, and so on). The DG834G v3 provides two methods for creating WEP encryption keys:
  • Passphrase. These characters are case sensitive. Enter a word or group of printable characters in the Passphrase box and click the Generate button. Note : Not all wireless adapters support passphrase key generation.
  • Manual. These values are not case sensitive. 64-bit WEP: enter 10 hexadecimal digits (any combination of 0-9, a-f, or A-F). 128-bit WEP: enter 26 hexadecimal digits (any combination of 0-9, a-f, or A-F).

Field Description · Wireless Configuration 3-5

Page 32 of the NETGEAR DG834G user manual — How to Set Up and Test Basic Wireless Connectivity
Page 32 · click to enlarge
Page 32

Table 3-1. Wireless Security Options (continued)

WPA-PSK (Wi- Fi Protected Access Pre- Shared Key)

WPA Pre-Shared-Key uses a pre-shared key to perform the authentication and generate the initial data encryption keys. Then, it dynamically varies the encryption key. For a full explanation of WPA, see “Wireless Communications” in Appendix C.

WPA-802.1x User authentication is implemented using 802.1x and RADIUS servers. For a full explanation of WPA, see “Wireless Communications” in Appendix C.

  • Fill in the following:
  • Radius Server Name/IP Address This field is required. Enter the name or IP address of the Radius Server on your LAN.
  • Radius Port Enter the port number used for connections to the Radius Server.
  • Radius Shared Key Enter the desired value for the Radius shared key. This key enables the DG834G v3 to log in to the Radius server and must match the value used on the Radius server.

How to Set Up and Test Basic Wireless Connectivity

Follow the instructions below to set up and test basic wireless connectivity. Once you have established basic wireless connectivity, you can enable security settings appropriate to your needs.

1. Log in to the DG834G v3 firewall at its default LAN address of http://192.168.0.1 with its default user name of admin and default password of password , or using whatever LAN address and password you have set up.
2. Click the Wireless Settings link in the main menu of the DG834G v3 firewall.
3. Choose a suitable descriptive name for the wireless network name (SSID). In the SSID box, enter a value of up to 32 alphanumeric characters. The default SSID is Wireless .

in the 54 Mbps ADSL Modem Wireless Router Model DG834G. If they do not match, you will not get a wireless connection to the DG834G v3.

Field Description · 3-6 Wireless Configuration

Page 33 of the NETGEAR DG834G user manual — How to Restrict Wireless Access to Your Network
Page 33 · click to enlarge
Page 33
4. Set the Region. Select the region in which the wireless interface will operate.
5. Set the Channel. The default channel is 11.

This field determines which operating frequency will be used. It should not be necessary to change the wireless channel unless you notice interference problems with another nearby wireless router or access point. Select a channel that is not being used by any other wireless networks within several hundred feet of your firewall. For more information on the wireless channel frequencies please refer to “Wireless Communications” in Appendix C.

6. For initial configuration and test, leave the Wireless Card Access List set to allow everyone access by making sure that Turn Access Control On is not selected in the Wireless Station Access List. In addition, leave the Encryption Strength set to “Disabled.”
7. Click Apply to save your changes.

the firewall’s SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change the wireless settings of your computer to match the firewall’s new settings.

8. Configure and test your computers for wireless connectivity.

Program the wireless adapter of your computers to have the same SSID and channel that you configured in the router. Check that they have a wireless link and are able to obtain an IP address by DHCP from the firewall.

Once your computers have basic wireless connectivity to the firewall, you can configure the advanced wireless security functions of the firewall.

How to Restrict Wireless Access to Your Network

By default, any wireless PC that is configured with the correct SSID will be allowed access to your wireless network. For increased security, the 54 Mbps ADSL Modem Wireless Router Model DG834G provides several ways to restrict wireless access to your network:

  • Turn off wireless connectivity completely
  • Restrict access based on the Wireless Network Name (SSID)
  • Restrict access based on the Wireless Card Access List

Wireless Configuration 3-7

Page 34 of the NETGEAR DG834G user manual — How to Restrict Wireless Access to Your Network
Page 34 · click to enlarge
Page 34

These options are discussed below.

NETGEAR DG834G — How to Restrict Wireless Access to Your Network diagram (page 34)
Fig. 6 · How to Restrict Wireless Access to Your Network

Restricting Access to Your Network by Turning Off Wireless Connectivity

You can completely turn off the wireless portion of the DG834G v3. For example, if your notebook computer is used to wirelessly connect to your router and you take a business trip, you can turn off the wireless portion of the router while you are traveling. Other members of your household who use computers connected to the router via Ethernet cables will still be able to use the router.

Restricting Wireless Access Based on the Wireless Network Name (SSID)

The DG834G v3 can restrict wireless access to your network by not broadcasting the wireless network name (SSID). However, by default, this feature is turned off. If you turn this feature on, wireless devices will not ‘see’ your DG834G v3. You must configure your wireless devices to match the wireless network name (SSID) you configure in the ADSL Modem Wireless Router.

the 54 Mbps ADSL Modem Wireless Router Model DG834G. If they do not match, you will not get a wireless connection to the DG834G v3.

Restricting Wireless Access Based on the Wireless Station Access List

This list determines which wireless hardware devices will be allowed to connect to the firewall.

To restrict access based on MAC addresses, follow these steps:

1. Log in to the DG834G v3 firewall at its default LAN address of http://192.168.0.1 with its default user name of admin and default password of password , or using whatever LAN address and password you have set up.

3-8 Wireless Configuration

Page 35 of the NETGEAR DG834G user manual — How to Restrict Wireless Access to Your Network
Page 35 · click to enlarge
Page 35
2. From the Wireless Settings menu, Wireless Station Access List section, click the Setup Access List button to display the list, shown below:
NETGEAR DG834G — How to Restrict Wireless Access to Your Network diagram (page 35)
Fig. 7 · How to Restrict Wireless Access to Your Network
3. Select the Turn Access Control On check box to enable restricting wireless computers by their MAC addresses.
4. If the wireless station is currently connected to the network, you can select it from the Available Wireless Stations list. Click Add to add the station to the Trusted Wireless Stations list.
5. If the wireless station is not currently connected, you can enter its address manually. Enter the MAC address of the authorized computer. The MAC address is usually printed on the wireless card, or it may appear in the modem router’s DHCP table. The MAC address will be 12 hexadecimal digits.

Click Add to add your entry. You can add several stations to the list, but the entries will be discarded if you do not click Apply.

Wireless Configuration 3-9

Page 36 of the NETGEAR DG834G user manual — Choosing WEP Authentication and Security Encryption Methods
Page 36 · click to enlarge
Page 36

You can copy and paste the MAC addresses from the modem router’s Attached Devices menu into the MAC Address box of this menu. To do this, configure each wireless computer to obtain a wireless link to the modem router. The computer should then appear in the Attached Devices menu.

MAC address is not in the Trusted Wireless Stations list, and you select Trusted Wireless Stations only, you will lose your wireless connection when you click Apply. You must then access the modem router from a wired computer to make any further changes.

6. Make sure the Turn Access Control On check box is selected, then click Apply .

Now, only devices on this list will be allowed to wirelessly connect to the DG834G v3. This prevents unauthorized access to your network.

Choosing WEP Authentication and Security Encryption Methods

NETGEAR DG834G — Choosing WEP Authentication and Security Encryption Methods diagram (page 36)
Fig. 8 · Choosing WEP Authentication and Security Encryption…

3-10 Wireless Configuration

Page 37 of the NETGEAR DG834G user manual — Choosing WEP Authentication and Security Encryption Methods
Page 37 · click to enlarge
Page 37

Restricting wireless access prevents intruders from connecting to your network. However, the wireless data transmissions are still vulnerable to snooping. Using the WEP data encryption settings described below will prevent a determined intruder from eavesdropping on your wireless data communications. Also, if you are using the Internet for such activities as purchases or banking, those Internet sites use another level of highly secure encryption called SSL. You can tell if a web site is using SSL because the web address begins with HTTPS rather than HTTP.

The DG834G v3 lets you select the following wireless authentication schemes.

  • Automatic
  • Open System
  • Shared key

authentication scheme which requires a shared key but still leave the data transmissions unencrypted. If you require strong security, use both the Shared Key and WEP encryption settings.

Set your wireless adapter according to the authentication scheme you choose for the ADSL Modem Wireless Router. Please refer to “Wireless Communications” in Appendix C for a full explanation of each of these options, as defined by the IEEE 802.11g wireless communication standard.

Please refer to “Wireless Communications” in Appendix C for a full explanation of each of the following choices, as defined by the IEEE 802.11g wireless communication standard. Choose the encryption strength from the drop-down list:

Disable. No encryption will be applied. This setting is useful for troubleshooting your wireless connection, but leaves your wireless data fully exposed.

64 or 128 bit WEP. When 64 Bit WEP or 128 Bit WEP is selected, WEP encryption will be applied.

If WEP is enabled, you can manually or automatically program the four data encryption keys. These values must be identical on all computers and access points in your network.

Authentication Type Selection · Encryption Choices · Wireless Configuration 3-11

Page 38 of the NETGEAR DG834G user manual — How to Configure WEP
Page 38 · click to enlarge
Page 38

There are two methods for creating WEP encryption keys:

  • Passphrase. Enter a word or group of printable characters in the Passphrase box and click the Generate button.
  • Manual. 64-bit WEP: Enter 10 hexadecimal digits (any combination of 0-9, a-f, or A-F). 128-bit WEP: Enter 26 hexadecimal digits (any combination of 0-9, a-f, or A-F).

Select the radio button for the key you want to make active.

How to Configure WEP

To configure WEP data encryption, follow these steps:

1. Log in to the DG834G v3 firewall at its default LAN address of http://192.168.0.1 with its default user name of admin and default password of password , or using whatever LAN address and password you have set up.
2. Click the Wireless Settings link in the Setup section of the main menu for the DG834G v3 modem router.
3. In the Security Options section, select the WEP (Wired Equivalent Privacy) radio button
4. Go to the WEP Security Encryption portion of the page:
NETGEAR DG834G — How to Configure WEP diagram (page 38)
Fig. 9 · How to Configure WEP
5. Select the Authentication Type .
6. Select the Encryption Strength setting.

3-12 Wireless Configuration

Page 39 of the NETGEAR DG834G user manual — How to Configure WPA-PSK
Page 39 · click to enlarge
Page 39
  • 7. Enter the encryption keys. You can manually or automatically program the four data encryption keys. These values must be identical on all computers and Access Points in your network.
  • Automatic — enter a word or group of printable characters in the Passphrase box and click the Generate button. The four key boxes will be automatically populated with key values.
  • Manual — enter hexadecimal digits (any combination of 0-9, a-f, or A-F). Select which of the four keys will be active.
8. Select the radio button for the key you want to make active.

Be sure you clearly understand how the WEP key settings are configured in your wireless adapter. Wireless adapter configuration utilities such as the one included in Windows XP only allow entry of one key which must match the default key you set in the DG834G v3.

9. Click Apply to save your settings.

WEP settings, you will lose your wireless connection when you click Apply. You must then either configure your wireless adapter to match the modem router WEP settings or access the modem router from a wired computer to make any further changes.

How to Configure WPA-PSK

wireless adapter for instructions on configuring WPA settings.

To configure WPA-PSK, follow these steps:

1. Log in at the default LAN address of http://192.168.0.1 with the default user name of admin and default password of password , or using whatever LAN address and password you have set up.
2. Click Wireless Settings in the Setup section of the main menu of the DG834G v3.
3. Choose the WPA-PSK radio button. The WPA-PSK page will display a WPA-PSK Security Encryption section.
4. Enter the pre-shared key in the Passphrase field.
5. Click Apply to save your settings.

Wireless Configuration 3-13

Page 40 of the NETGEAR DG834G user manual — How to Configure WPA-802.1x
Page 40 · click to enlarge
Page 40

How to Configure WPA-802.1x

wireless adapter for instructions on configuring WPA settings.

To configure WPA-802.1x, follow these steps:

1. Log in at the default LAN address of http://192.168.0.1 with the default user name of admin and default password of password , or using whatever LAN address and password you have set up.
2. Click Wireless Settings in the Setup section of the main menu of the DG834G v3.
3. Choose the WPA-802.1x radio button. The page will display the WPA-802.1x section.
4. Enter the Radius server name/IP address.
5. Enter the Radius port number.
6. Enter the Shared Key.
7. Click Apply to save your settings.

3-14 Wireless Configuration

Page 41 of the NETGEAR DG834G user manual — How to Change the Built-In Password
Page 41 · click to enlarge
Page 41

Chapter 4 Protecting Your Network

This chapter describes how to use the basic firewall features of the 54 Mbps ADSL Modem Wireless Router Model DG834G to protect your network. It also describes how to configure Trend Micro Home Network Security.

Protecting Access to Your 54 Mbps ADSL Modem Wireless Router Model DG834G

For security reasons, the modem router has its own user name and password. Also, after a period of inactivity for a set length of time, the administrator login will automatically disconnect. When prompted, enter admin for the modem router User Name and password for the modem router Password. You can use procedures below to change the modem router's password and the amount of time for the administrator’s login timeout.

may use to log in to your Internet connection.

NETGEAR recommends that you change this password to a more secure password. The ideal password should contain no dictionary words from any language, and should be a mixture of both upper and lower case letters, numbers, and symbols. Your password can be up to 30 characters.

How to Change the Built-In Password

1. Log in to the modem router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever Password and LAN address you have chosen for the modem router.
NETGEAR DG834G — How to Change the Built-In Password diagram (page 41)
Fig. 10 · How to Change the Built-In Password

Protecting Your Network 4-1

Page 42 of the NETGEAR DG834G user manual — Changing the Administrator Login Timeout
Page 42 · click to enlarge
Page 42
2. From the Main Menu of the browser interface, under the Maintenance heading, select Set Password to bring up the menu shown.
NETGEAR DG834G — Changing the Administrator Login Timeout diagram (page 42)
Fig. 11 · Changing the Administrator Login Timeout
3. To change the password, first enter the old password, and then enter the new password twice.
4. Click Apply to save your changes.

the configuration. If you have backed up the modem router settings previously, you should do a new backup so that the saved settings file includes the new password.

Changing the Administrator Login Timeout

For security, the administrator's login to the modem router configuration will timeout after a period of inactivity. To change the login timeout period:

1. In the Set Password menu, type a number in ‘Administrator login times out’ field. The suggested default value is 5 minutes.
2. Click Apply to save your changes or click Cancel to keep the current period.

4-2 Protecting Your Network

Page 43 of the NETGEAR DG834G user manual — How to Block Keywords and Sites
Page 43 · click to enlarge
Page 43

Configuring Basic Firewall Services

Basic firewall services you can configure include access blocking and scheduling of firewall security. These topics are presented below.

Blocking Keywords, Sites, and Services

The modem router provides a variety of options for blocking Internet based content and communications services. With its content filtering feature, the ADSL Modem Wireless Router prevents objectionable content from reaching your PCs. The modem router allows you to control access to Internet content by screening for keywords within Web addresses. Key content filtering options include:

  • Keyword blocking of HTTP traffic.
  • Outbound Service Blocking limits access from your LAN to Internet locations or services that you specify as off-limits.
  • Denial of Service (DoS) protection. Automatically detects and thwarts Denial of Service (DoS) attacks such as Ping of Death, SYN Flood, LAND Attack and IP Spoofing.
  • Blocking unwanted traffic from the Internet to your LAN.

The section below explains how to configure your modem router to perform these functions.

How to Block Keywords and Sites

The ADSL Modem Wireless Router allows you to restrict access to Internet content based on functions such as Web addresses and Web address keywords.

1. Log in to the modem router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever Password and LAN address you have chosen for the modem router.

Protecting Your Network 4-3

Page 44 of the NETGEAR DG834G user manual — Configuring Basic Firewall Services
Page 44 · click to enlarge
Page 44
2. Select the Block Sites link of the Security menu.
NETGEAR DG834G — Configuring Basic Firewall Services diagram (page 44)
Fig. 12 · Configuring Basic Firewall Services
3. To enable keyword blocking, select one of the following:
  • Per Schedule —to turn on keyword blocking according to the settings on the Schedule page.
  • Always —to turn on keyword blocking all of the time, independent of the Schedule page.
4. Enter a keyword or domain in the Keyword box, click Add Keyword , then click Apply .

Some examples of Keyword application follow:

  • If the keyword “XXX” is specified, the URL <<a href="http://www.badstuff.com/xxx.html&gt;" rel="nofollow noopener" target="_blank">http://www.badstuff.com/xxx.html&gt;</a> is blocked.
  • If the keyword “.com” is specified, only Web sites with other domain suffixes (such as .edu or .gov) can be viewed.
  • Enter the keyword “.” to block all Internet browsing access.

Up to 32 entries are supported in the Keyword list.

5. To delete a keyword or domain, select it from the list, click Delete Keyword , then click Apply .
6. To specify a trusted user, enter that computer’s IP address in the Trusted IP Address box and click Apply .

4-4 Protecting Your Network

Page 45 of the NETGEAR DG834G user manual — Firewall Rules
Page 45 · click to enlarge
Page 45

You can specify one trusted user, which is a computer that will be exempt from blocking and logging. Since the trusted user will be identified by an IP address, you should configure that computer with a fixed IP address.

7. Click Apply to save your settings.

enabled. This is because the Trend security system has incorporates its own site- blocking capability.

Firewall Rules

Firewall rules are used to block or allow specific traffic passing through from one side of the router to the other. Inbound rules (WAN to LAN) restrict access by outsiders to private resources, selectively allowing only specific outside users to access specific resources. Outbound rules (LAN to WAN) determine what outside resources local users can have access to.

A firewall has two default rules, one for inbound traffic and one for outbound. The default rules of the DG834G v3 are:

  • Inbound: Block all access from outside except responses to requests from the LAN side.
  • Outbound: Allow all access from the LAN side to the outside.

You can define additional rules that will specify exceptions to the default rules. By adding custom rules, you can block or allow access based on the service or application, source or destination IP addresses, and time of day. You can also choose to log traffic that matches or does not match the rule you have defined.

You can change the order of precedence of rules so that the rule that applies most often will take effect first. See “Order of Precedence for Rules” on page 4-11 for more details.

Protecting Your Network 4-5

Page 46 of the NETGEAR DG834G user manual — Inbound Rules (Port Forwarding)
Page 46 · click to enlarge
Page 46

To access the rules configuration of the DG834G v3, click the Firewall Rules link on the main menu, then click Add for either an Outbound or Inbound Service.

NETGEAR DG834G — Inbound Rules (Port Forwarding) diagram (page 46)
Fig. 13 · Inbound Rules (Port Forwarding)
  • To edit an existing rule, select its button on the left side of the table and click Edit .
  • To delete an existing rule, select its button on the left side of the table and click Delete .
  • To move an existing rule to a different position in the table, select its button on the left side of the table and click Move . At the script prompt, enter the number of the desired new position and click OK .

Inbound Rules (Port Forwarding)

Because the DG834G v3 uses Network Address Translation (NAT), your network presents only one IP address to the Internet, and outside users cannot directly address any of your local computers. However, by defining an inbound rule you can make a local server (for example, a Web server or game server) visible and available to the Internet. The rule tells the modem router to direct inbound traffic for a particular service to one local server based on the destination port number. This is also known as port forwarding.

processes (such as a Web or FTP server) from your location. Your ISP may periodically check for servers and may suspend your account if it discovers any active services at your location. If you are unsure, refer to the Acceptable Use Policy of your ISP.

4-6 Protecting Your Network

Page 47 of the NETGEAR DG834G user manual — Inbound Rules (Port Forwarding)
Page 47 · click to enlarge
Page 47

Remember that allowing inbound services opens holes in your firewall. Only enable those ports that are necessary for your network. Following are two application examples of inbound rules:

Inbound Rule ExampleA Local Public Web Server

If you host a public Web server on your local network, you can define a rule to allow inbound Web (HTTP) requests from any outside IP address to the IP address of your Web server at any time of day. This rule is shown:

NETGEAR DG834G — Inbound Rules (Port Forwarding) diagram (page 47)
Fig. 14 · Inbound Rules (Port Forwarding)

The parameters are:

  • Service— From this list, select the application or service to be allowed or blocked. The list already displays many common services, but you are not limited to these choices. Use the Services menu to add any additional services or applications that do not already appear.
  • Action— Choose how you want this type of traffic to be handled. You can block or allow always, or you can choose to block or allow according to the schedule you have defined in the Schedule menu.
  • Send to LAN Server— Enter the IP address of the computer or server on your LAN which will receive the inbound traffic covered by this rule.

Protecting Your Network 4-7

Page 48 of the NETGEAR DG834G user manual — Inbound Rules (Port Forwarding)
Page 48 · click to enlarge
Page 48
  • WAN Users— These settings determine which packets are covered by the rule, based on their source (WAN) IP address. Select the desired option:

– Any — all IP addresses are covered by this rule.

– Address range — if this option is selected, you must enter the Start and Finish fields.

– Single address — enter the required address in the Start field.

  • Log— You can select whether the traffic will be logged. The choices are:

– Never — no log entries will be made for this service.

– Always — any traffic for this service type will be logged.

– Match — traffic of this type which matches the parameters and action will be logged.

– Not match — traffic of this type which does not match the parameters and action will be logged.

Inbound Rule ExampleAllowing Videoconferencing

If you want to allow incoming videoconferencing to be initiated from a restricted range of outside IP addresses, such as from a branch office, you can create an inbound rule. In the example shown here, CU-SeeMe connections are allowed only from a specified range of external IP addresses. In this case, we have also specified logging of any incoming CU-SeeMe requests that do not match the allowed parameters.

NETGEAR DG834G — Inbound Rules (Port Forwarding) diagram (page 48)
Fig. 15 · Inbound Rules (Port Forwarding)

4-8 Protecting Your Network

Page 49 of the NETGEAR DG834G user manual — Outbound Rules (Service Blocking)
Page 49 · click to enlarge
Page 49

Considerations for Inbound Rules

If your external IP address is assigned dynamically by your ISP, the IP address may change periodically as the DHCP lease expires. Consider using the Dynamic DNS feature in the Advanced menu so that external users can always find your network.

If the IP address of the local server computer is assigned by DHCP, it may change when the computer is rebooted. To avoid this, use the Reserved IP address feature in the LAN IP menu to keep the computer’s IP address constant.

Local computers must access the local server using the computer’s local LAN address (192.168.0.11 in the example above). Attempts by local computers to access the server using the external WAN IP address will fail.

Outbound Rules (Service Blocking)

The DG834G v3 allows you to block the use of certain Internet services by computers on your network. This is called service blocking or port filtering. You can define an outbound rule to block Internet access from a local computer based on:

  • IP address of the local computer (source address)
  • IP address of the Internet site being contacted (destination address)
  • Time of day
  • Type of service being requested (service port number)

Following is an application example of outbound rules.

Protecting Your Network 4-9

Page 50 of the NETGEAR DG834G user manual — Outbound Rules (Service Blocking)
Page 50 · click to enlarge
Page 50
Outbound Rule ExampleBlocking Instant Messenger

If you want to block Instant Messenger usage by employees during working hours, you can create an outbound rule to block that application from any internal IP address to any external address according to the schedule that you have created in the Schedule menu. You can also have the modem router log any attempt to use Instant Messenger during that blocked period.

NETGEAR DG834G — Outbound Rules (Service Blocking) diagram (page 50)
Fig. 16 · Outbound Rules (Service Blocking)

The parameters are:

  • Service— From this list, select the application or service to be allowed or blocked. The list already displays many common services, but you are not limited to these choices. Use the Add Custom Service feature to add any additional services or applications that do not already appear.
  • Action— Choose how you want this type of traffic to be handled. You can block or allow always, or you can choose to block or allow according to the schedule you have defined in the Schedule menu.
  • LAN Users— These settings determine which packets are covered by the rule, based on their source LAN IP address. Select the desired option:

– Any — all IP addresses are covered by this rule.

– Address range — if this option is selected, you must enter the Start and Finish fields.

– Single address — enter the required address in the Start field.

4-10 Protecting Your Network

Page 51 of the NETGEAR DG834G user manual — Order of Precedence for Rules
Page 51 · click to enlarge
Page 51
  • WAN Users— These settings determine which packets are covered by the rule, based on their destination WAN IP address. Select the desired option:

– Any — all IP addresses are covered by this rule.

– Address range —if this option is selected, you must enter the Start and Finish fields.

– Single address — enter the required address in the Start field.

  • Log— You can select whether the traffic will be logged. The choices are:

– Never — no log entries will be made for this service.

– Always — any traffic for this service type will be logged.

– Match — traffic of this type that matches the parameters and action will be logged.

– Not match — traffic of this type that does not match the parameters and action will be logged.

Order of Precedence for Rules

As you define new rules, they are added to the tables in the Rules menu, as shown:

NETGEAR DG834G — Order of Precedence for Rules diagram (page 51)
Fig. 17 · Order of Precedence for Rules

Protecting Your Network 4-11

Page 52 of the NETGEAR DG834G user manual — How to Define Services
Page 52 · click to enlarge
Page 52

For any traffic attempting to pass through the firewall, the packet information is subjected to the rules in the order shown in the Rules Table, beginning at the top and proceeding to the default rules at the bottom. In some cases, the order of precedence of two or more rules may be important in determining the disposition of a packet. The Move button allows you to relocate a defined rule to a new position in the table.

Services

Services are functions performed by server computers at the request of client computers. For example, Web servers serve Web pages, time servers serve time and date information, and game hosts serve data about other players’ moves. When a computer on the Internet sends a request for service to a server computer, the requested service is identified by a service or port number. This number appears as the destination port number in the transmitted IP packets. For example, a packet that is sent with destination port number 80 is an HTTP (Web server) request.

The service numbers for many common protocols are defined by the Internet Engineering Task Force (IETF) and published in RFC1700, “Assigned Numbers.” Service numbers for other applications are typically chosen from the range 1024 to 65535 by the authors of the application.

Although the DG834G v3 already holds a list of many service port numbers, you are not limited to these choices. Use the procedure below to create your own service definitions.

How to Define Services

1. Log in to the modem router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever Password and LAN address you have chosen for the modem router.
2. Select the Services link of the Security menu to display the Services menu shown:
NETGEAR DG834G — How to Define Services diagram (page 52)
Fig. 18 · How to Define Services
  • To create a new Service, click the Add Custom Service button.

4-12 Protecting Your Network

Page 53 of the NETGEAR DG834G user manual — How to Set Your Time Zone
Page 53 · click to enlarge
Page 53
  • To edit an existing Service, select its button on the left side of the table and click Edit Service .
  • To delete an existing Service, select its button on the left side of the table and click Delete Service .
3. Use the page shown below to define or edit a service.
NETGEAR DG834G — Setting Times and Scheduling Firewall Services diagram (page 53)
Fig. 19 · Setting Times and Scheduling Firewall Services
4. Click Apply to save your changes.

Setting Times and Scheduling Firewall Services

The ADSL Modem Wireless Router uses the Network Time Protocol (NTP) to obtain the current time and date from one of several Network Time Servers on the Internet.

How to Set Your Time Zone

In order to localize the time for your log entries, you must specify your Time Zone:

1. Log in to the modem router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever Password and LAN address you have chosen for the modem router.

Protecting Your Network 4-13

Page 54 of the NETGEAR DG834G user manual — Setting Times and Scheduling Firewall Services
Page 54 · click to enlarge
Page 54
2. Select the Schedule link of the Security menu to display menu shown below.
NETGEAR DG834G — Setting Times and Scheduling Firewall Services diagram (page 54)
Fig. 20 · Setting Times and Scheduling Firewall Services
3. Select your time zone. This setting will be used for the blocking schedule according to your local time zone and for time-stamping log entries.

Select the Adjust for daylight savings time check box if your time zone is currently in daylight savings time.

for Daylight Savings Time on the first day of Daylight Savings Time, and clear it at the end. Enabling Daylight Savings Time will cause one hour to be added to the standard time.

4. The modem router has a list of NETGEAR NTP servers. If you would prefer to use a particular NTP server as the primary server, enter its IP address under Use this NTP Server.
5. Click Apply to save your settings.

4-14 Protecting Your Network

Page 55 of the NETGEAR DG834G user manual — Trend Micro Home Network Security
Page 55 · click to enlarge
Page 55

How to Schedule Firewall Services

If you enabled services blocking in the Block Services menu or Port forwarding in the Ports menu, you can set up a schedule for when blocking occurs or when access is not restricted.

1. Log in to the modem router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever Password and LAN address you have chosen for the modem router.
2. Select the Schedule link of the Security menu to display menu shown above.
3. To block Internet services based on a schedule, select Every Day or select one or more days. If you want to limit access completely for the selected days, select All Day . Otherwise, to limit access during certain times for the selected days, enter Start Blocking and End Blocking times.
4. Enter the values in 24-hour time format. For example, 10:30 am would be 10 hours and 30 minutes and 10:30 pm would be 22 hours and 30 minutes. If you set the start time after the end time, the schedule will be effective through midnight the next day.
5. Click Apply to save your changes.

Trend Micro Home Network Security

You can enable Home Network Security as if you didn’t do so when you originally set up your router. Home routers provide an enhanced Internet experience, but the likelihood of attacks also increases. Trend Micro Home Network Security addresses the security needs of computers accessing the Internet via home routers.

Network Security. To take advantage of this feature you must register an account with Trend Micro. For more information, refer to the Home Network Security Quick Start Guide on the NETGEAR Resource CD, or to http://www.trendmicro.com/offers/netgear. The Trend Micro software requires Microsoft Internet Explorer 5.5 or higher.

Protecting Your Network 4-15

Page 56 of the NETGEAR DG834G user manual — Security Service Settings
Page 56 · click to enlarge
Page 56

To begin using Home Network Security, configure the Security Service and Parental Controls menus on your ADSL Modem Wireless Router. Each screen has a GUI button to click that will take you to the Trend Micro Web site to open your Trend Micro account.

Block Keywords and Sites” on page 4-3, is disabled if you enable Trend Micro Home Security.

Security Service Settings

Click Security Service under Content Filtering on the Main menu to get the Security Service Settings menu shown below:

NETGEAR DG834G — Security Service Settings diagram (page 56)
Fig. 21 · Security Service Settings

Click this banner to install the Trend Micro dashboard and set up your Trend Micro account.

To install Home Network Security, click the Trend Micro banner and then follow the on-screen instructions. For assistance, refer to the Home Network Security Quick Start Guide included on the NETGEAR Resource CD. (You can download this document and the Home Network Security User’s Guide at http://www.trendmicro.com/en/support/tmss/netgear)

4-16 Protecting Your Network

Page 57 of the NETGEAR DG834G user manual — Security Service Settings
Page 57 · click to enlarge
Page 57
  • Enable Trend Micro Security Services . Select this check box and then click Apply to enable the Security Service features on this page (automatic updates and Client Virus Protection Status information).
  • Automatically check for update components . Select this check box to automatically check for updates to Trend Micro scanning components. Choose the desired checking interval from the list, and then click Apply .

frequency to once a day.

  • Client Virus Protection Status . Provides information on all computers on your network.
– IP AddressThe computer’s IP address
– Computer NameThe name of the computer (as shown in Control Panel > System)
– Antivirus SoftwareThe type of antivirus software installed on the computer
– Virus Def. File VersionThe version of the virus pattern file in use by the antivirus software
– Scan EngineThe version of the scan engine in use by the antivirus software

– Status: Indicates if the virus pattern file or scan engine require updating (if no recognized antivirus software is found, the status is “Potential Threat”)

Protecting Your Network 4-17

Page 58 of the NETGEAR DG834G user manual — Parental Controls Settings
Page 58 · click to enlarge
Page 58

Parental Controls Settings

Click Parental Controls under Content Filtering on the Main menu to get the Trend Micro Parental Controls menu shown below:

NETGEAR DG834G — Parental Controls Settings diagram (page 58)
Fig. 22 · Parental Controls Settings

Click this banner to install the Trend Micro

dashboard and set up your Trend Micro account.

NETGEAR DG834G — Parental Controls Settings diagram (page 58)
Fig. 23 · Parental Controls Settings
Figure 4-13Trend Micro Parental Controls menu

To configure Parental Controls:

  • Click Always to turn on Parental Controls all the time.
  • Click Never to turn off Parental Controls.
  • Click Per Schedule to turn on Parental Controls at the times specified on the Schedule page.

4-18 Protecting Your Network

Page 59 of the NETGEAR DG834G user manual — Parental Controls Settings
Page 59 · click to enlarge
Page 59

To select Parental Controls Mode:

  • Click Use General Controls to select General mode. In General mode, one access profile applies to all users.
  • Click Use Per-User Controls to select Per-User mode. In Per-User mode, each user has an individual access profile.

required to log in.

To configure General mode:

1. Enter a password in the Parental Controls Bypass Password box, re-enter it in the Confirm password box, and then click Apply . This password allows users to access pages that are blocked by Parental Controls.
2. Select the access profile that will apply to all users, as follows:
  • To select a predefined profile, click Apply Profile and then choose a profile from the list.
  • To create a custom profile, click Use Custom Settings and then select the check boxes as desired. (For additional choices, click More Categories ).
  • To allow unrestricted Internet access, click No Restrictions .
3. Click Apply .

To configure Per-User mode:

The User Account Information table in Per-User mode shows each user’s name, access profile, and status. Users with Active status can access the Internet sites permitted by their access profiles. Users with Inactive status cannot log in and cannot access any Internet sites.

To add a new user:

1. Click Add . Type the new user’s login name and password, and then re-enter the password in the Confirm password box.
2. Select the new user’s status. To allow Internet access, click Active . To completely disable this user’s Internet access, click Inactive .
3. Select the access profile that will apply to this user, as follows:
  • To select a predefined profile, click Apply Profile and then choose a profile from the list.

Protecting Your Network 4-19

Page 60 of the NETGEAR DG834G user manual — Parental Controls Settings
Page 60 · click to enlarge
Page 60
  • To create a custom profile, click Use Custom Settings and then select the check boxes as desired. (For additional choices, click More Categories ).
  • To allow unrestricted Internet access, click No Restrictions .
4. Click Apply .

To change a user’s account information:

1. Select the user’s name in the User Account Information table and then click Edit .
2. Make the desired changes, and then click Apply .

To delete a user, select the user’s name in the User Account Information table and then click Delete.

Click Parental Controls Logs to view attempts to access restricted sites, and actual accesses.

Blocking criteria for potentially offensive categories

Trend Micro has defined twelve potentially offensive categories of Web sites. Following are the blocking criteria for each category:

  • Adult/Mature Content : Sites that contain material of an adult nature but without excessive violence, sexual content, or nudity. These sites may include profane or vulgar content not appropriate for children.
  • Alcohol/Tobacco : Sites that promote or sell alcohol and tobacco products. Includes sites that glamorize or otherwise encourage alcohol or tobacco use. Does not include sites that sell alcohol or tobacco as a subset of another business.
  • Gambling : Sites where users can place bets or participate in betting pools (including lotteries) online. Also includes sites that provide information, assistance, recommendations, or training on placing bets or participating in games of chance. Does not include sites that sell gamblingrelated products or machines. Also does not include offline casino and hotel sites, unless meeting one of the foregoing criteria).
  • Hacking/Proxy Avoidance : Sites providing information on illegal or questionable access to, or use of, communications equipment and software, or that provide information on how to bypass proxy server features or gain unauthorized access to URLs.
  • Illegal Drugs : Sites that promote, offer, sell, supply, or advocate the illegal use, cultivation, manufacture, or distribution of drugs, pharmaceuticals, intoxicating plants and chemicals, and related paraphernalia.

4-20 Protecting Your Network

Parental Controls Logs

Page 61 of the NETGEAR DG834G user manual — Parental Controls Settings
Page 61 · click to enlarge
Page 61
  • Illegal/Questionable : Sites that advocate or advise on performing illegal acts such as service theft, evading law enforcement, fraud, burglary techniques, and plagiarism. Also includes sites that provide or sell questionable educational materials, such as term papers.
  • Intimate Apparel/Swimsuit : Sites that contain images of swimsuits, intimate apparel, or other suggestive clothing. Does not include sites selling undergarments as a subset of another business.
  • Nudity : Sites containing nude or seminude depictions of the human body. Such depictions need not be sexual in intent or effect. May include sites containing nude paintings or photo galleries of an artistic nature. This category includes nudist or naturist sites.
  • Pornography : Sites that contain sexually explicit material.
  • Sex Education : Sites that provide information (sometimes graphic) on reproduction, sexual development, safe sex practices, sexuality, birth control, and sexual development. Also includes sites that offer tips for better sex as well as products used for sexual enhancement.
  • Violence/Hate/Racism : Sites depicting or advocating physical harm to people or property. Includes sites that convey hostility or aggression toward, or the denigration of, an individual or group on the basis of race, religion, gender, nationality, ethnic origin, and so forth.
  • Weapons : Sites that sell, review, or describe guns, knives, martial arts devices, and related accessories. Does not include sites that promote weapons collecting, or groups that either support or oppose weapons ownership.

Protecting Your Network 4-21

Page 62 of the NETGEAR DG834G user manual — Parental Controls Settings
Page 62 · click to enlarge
Page 62

4-22 Protecting Your Network

Page 63 of the NETGEAR DG834G user manual — How to Back Up the Configuration to a File
Page 63 · click to enlarge
Page 63

Chapter 5 Managing Your Network

This chapter describes how to perform network management tasks with your 54 Mbps ADSL Modem Wireless Router Model DG834G.

Backing Up, Restoring, or Erasing Your Settings

The configuration settings of the ADSL Modem Wireless Router are stored in a configuration file in the modem router. This file can be backed up to your computer, restored, or reverted to factory default settings. The procedures below explain how to do these tasks.

How to Back Up the Configuration to a File

1. Log in to the modem router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever User Name, Password and LAN address you have chosen for the modem router.
2. From the Maintenance heading of the Main Menu, select the Backup Settings menu shown.
NETGEAR DG834G — How to Back Up the Configuration to a File diagram (page 63)
Fig. 24 · How to Back Up the Configuration to a File
3. Click Backup to save a copy of the current settings.
4. Store the .cfg file on a computer on your network.

Managing Your Network 5-1

Page 64 of the NETGEAR DG834G user manual — Upgrading the Modem Router’s Firmware
Page 64 · click to enlarge
Page 64

How to Restore the Configuration from a File

1. Log in to the modem router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever User Name, Password and LAN address you have chosen for the modem router.
2. From the Maintenance heading of the Main Menu, select the Settings Backup menu.
3. Enter the full path to the file on your network or click the Browse button to locate the file.
4. When you have located the .cfg file, click the Restore button to upload the file to the modem router.
5. The modem router will then reboot automatically.

How to Erase the Configuration

It is sometimes desirable to restore the modem router to the factory default settings. This can be done by using the Erase function.

1. To erase the configuration, from the Maintenance menu Settings Backup link, click the Erase button on the screen.
2. The modem router will then reboot automatically.

After an erase, the modem router's password will be password, the LAN IP address will be 192.168.0.1, and the modem router's DHCP client will be enabled.

password or IP address, you must use the Default Reset button on the rear panel of the modem router. See “The Router’s Rear Panel” on page 2-9.

Upgrading the Modem Router’s Firmware

The software of the ADSL Modem Wireless Router is stored in FLASH memory, and can be upgraded as new software is released by NETGEAR.

Upgrade files can be downloaded from NETGEAR's Web site. If the upgrade file is compressed (.ZIP file), you must first extract the binary (.BIN or .IMG) file before uploading it to the modem router.

5-2 Managing Your Network

Page 65 of the NETGEAR DG834G user manual — How to Upgrade the Modem Router Firmware
Page 65 · click to enlarge
Page 65

How to Upgrade the Modem Router Firmware

NETGEAR recommends that you back up your configuration before doing a firmware upgrade. After the upgrade is complete, you may need to restore your configuration settings.

1. Download and unzip the new software file from NETGEAR.

The Web browser used to upload new firmware into the modem router must support HTTP uploads. NETGEAR recommends using Microsoft Internet Explorer 5.0 or above, or Netscape Navigator 4.7 or above.

2. Log in to the modem router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever User Name, Password and LAN address you have chosen for the modem router.
3. From the Main Menu of the browser interface, under the Maintenance heading, select the Modem Router Upgrade heading to display the menu shown.
NETGEAR DG834G — How to Upgrade the Modem Router Firmware diagram (page 65)
Fig. 25 · How to Upgrade the Modem Router Firmware
4. In the Modem Router Upgrade menu, click the Browse to locate the binary (.BIN or .IMG) upgrade file.
5. Click Upload .

interrupt the Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, it may corrupt the software. When the upload is complete, your modem router will automatically restart. The upgrade process will typically take about one minute. In some cases, you may need to clear the configuration and reconfigure the modem router after upgrading.

Managing Your Network 5-3

Page 66 of the NETGEAR DG834G user manual — Viewing Modem Router Status and Usage Statistics
Page 66 · click to enlarge
Page 66

Network Management Information

The DG834G v3 provides a variety of status and usage information which is discussed below.

Viewing Modem Router Status and Usage Statistics

From the Main Menu, under Maintenance, click Modem Router Status to view this screen.

NETGEAR DG834G — Viewing Modem Router Status and Usage Statistics diagram (page 66)
Fig. 26 · Viewing Modem Router Status and Usage Statistics

The Modem Router Status menu provides status and usage information.

5-4 Managing Your Network

Page 67 of the NETGEAR DG834G user manual — Network Management Information
Page 67 · click to enlarge
Page 67

This screen shows the following parameters:

Table 5-1. Menu 3.2 - Modem Router Status Fields

Account Name The Host Name assigned to the modem router in the Basic Settings menu.

Firmware Version This field displays the modem router firmware version.

ADSL Port These parameters apply to the Internet (ADSL) port of the modem router.

MAC Address This field displays the Ethernet MAC address being used by the Internet (ADSL) port of the modem router.

IP Address This field displays the IP address being used by the Internet (ADSL) port of the modem router. If no address is shown, the modem router cannot connect to the Internet.

Network Type The network type depends is determined by your ISP. Common network types are PPPoE and PPPoA.

IP Subnet Mask This field displays the IP Subnet Mask being used by the Internet (ADSL) port of the modem router.

Domain Name Server (DNS)

This field displays the DNS Server IP addresses being used by the modem router. These addresses are usually obtained dynamically from the ISP.

LAN Port These parameters apply to the Local (ADSL) port of the modem router.

MAC Address This field displays the Ethernet MAC address being used by the Local (LAN) port of the modem router.

IP Address This field displays the IP address being used by the Local (LAN) port of the modem router. The default is 192.168.0.1.

DHCP If OFF, the modem router will not assign IP addresses to PCs on the LAN. If ON, the modem router will assign IP addresses to PCs on the LAN.

IP Subnet Mask This field displays the IP Subnet Mask being used by the Local (LAN) port of the modem router. The default is 255.255.255.0.

Modem These parameters apply to the Local (WAN) port of the modem router.

ADSL Firmware Version The version of the firmware.

Modem Status The connection status of the modem.

Managing Your Network 5-5

Field Description

Page 68 of the NETGEAR DG834G user manual — Network Management Information
Page 68 · click to enlarge
Page 68

Table 5-1. Menu 3.2 - Modem Router Status Fields (continued)

Downstream Speed The speed at which the modem is receiving data from the ADSL line.

Upstream Speed The speed at which the modem is transmitting data to the ADSL line.

VPI The Virtual Path Identifier setting.

VCI The Virtual Channel Identifier setting.

Wireless Port These are the settings as set in the Wireless Settings page; see “Understanding Wireless Settings” in Chapter 3 for details.

Name (SSID) The Service Set ID, also known as the wireless network name.

Region The country where the unit is set up for use.

Channel The current channel, which determines the operating frequency.

Wireless AP Indicates if the Access Point feature is disabled or not. If not enabled, the Wireless LED on the front panel will be off.

Broadcast Name Indicates if the DG834G v3 is configured to broadcast its SSID.

Click the Show Statistics button to display modem router usage statistics, as shown below:

NETGEAR DG834G — Network Management Information diagram (page 68)
Fig. 27 · Network Management Information

5-6 Managing Your Network

Field Description

Page 69 of the NETGEAR DG834G user manual — Network Management Information
Page 69 · click to enlarge
Page 69

This screen shows the following statistics:

Table 5-2. Router Statistics Fields

WAN or LAN Port The statistics for the WAN (Internet) and LAN ports.

Status The link status of the port.

TxPkts The number of packets transmitted on this port since reset or manual clear.

RxPkts The number of packets received on this port since reset or manual clear.

Collisions The number of collisions on this port since reset or manual clear.

Tx B/s The current line utilization—percentage of current bandwidth used on this port.

Rx B/s The average line utilization for this port.

Up Time The time elapsed since the last power cycle or reset.

ADSL Link Downstream or Upstream

The statistics for the upstream and downstream ADSL link. These statistics will be of interest to your technical support representative if you are having problems obtaining or maintaining a connection.

Connection Speed Typically, the downstream speed is faster than the upstream speed.

Line Attenuation The line attenuation will increase the further you are physically located from your ISP’s facilities.

Noise Margin This is the signal-to-noise ratio and is a measure of the quality of the signal on the line.

Poll Interval Specifies the interval at which the statistics are updated in this window. Click Stop to freeze the display.

Managing Your Network 5-7

Field Description

Page 70 of the NETGEAR DG834G user manual — Network Management Information
Page 70 · click to enlarge
Page 70

Click the Connection Status button to display modem router connection status, shown below:

NETGEAR DG834G — Network Management Information diagram (page 70)
Fig. 28 · Network Management Information

This screen shows the following statistics:

Table 5-3. Connection Status Fields for PPPoA

Connection Time The time elapsed since the last connection to the Internet via the ADSL port.

The connection status.

Negotiation ON or OFF

Authentication ON or OFF

IP Address The IP Address assigned to the WAN port by the ADSL Internet Service Provider.

Network Mask The Network Mask assigned to the WAN port by the ADSL Internet Service Provider.

5-8 Managing Your Network

Field Description · Connecting to Sender

Page 71 of the NETGEAR DG834G user manual — Viewing, Selecting, and Saving Logged Information
Page 71 · click to enlarge
Page 71

Viewing Attached Devices

The Attached Devices menu contains a table of all IP devices that the modem router has discovered on the local network. From the Main Menu of the browser interface, under the Maintenance heading, select Attached Devices to view the table, shown:

NETGEAR DG834G — Viewing Attached Devices diagram (page 71)
Fig. 29 · Viewing Attached Devices

For each device, the table shows the IP address, Device Name if available, and the Ethernet MAC address. Note that if the modem router is rebooted, the table data is lost until the modem router rediscovers the devices. To force the modem router to look for attached devices, click the Refresh button.

Viewing, Selecting, and Saving Logged Information

The modem router will log security-related events such as denied incoming service requests, hacker probes, and administrator logins. If you enabled content filtering in the Block Sites menu, the Logs page can show you when someone on your network tries to access a blocked site. If you enabled e-mail notification, you will receive these logs in an e-mail message. If you do not have e- mail notification enabled, you can view the logs here.

Managing Your Network 5-9

Page 72 of the NETGEAR DG834G user manual — Viewing Attached Devices
Page 72 · click to enlarge
Page 72

An example of the logs file is shown below.

NETGEAR DG834G — Viewing Attached Devices diagram (page 72)
Fig. 30 · Viewing Attached Devices

5-10 Managing Your Network

Page 73 of the NETGEAR DG834G user manual — Viewing Attached Devices
Page 73 · click to enlarge
Page 73

Log entries are described in Table 5-4 below:

Table 5-4. Security Log entry descriptions

Date and Time The date and time the log entry was recorded.

The type of event and what action was taken if any.

Source IP The IP address of the initiating device for this log entry.

Source port and interface

The service port number of the initiating device, and whether it originated from the LAN or WAN

Destination The name or IP address of the destination device or Web site.

Destination port and interface

The service port number of the destination device, and whether it’s on the LAN or WAN.

Log action buttons are described in Table 5-5 below:

Table 5-5. Security Log action buttons

Refresh Refresh the log screen.

Clear Log Clear the log entries.

Send Log Email the log immediately.

Apply Apply the current settings.

Cancel Clear the current settings.

Managing Your Network 5-11

Field Description · Description or Action · Field Description

Page 74 of the NETGEAR DG834G user manual — Examples of Log Messages
Page 74 · click to enlarge
Page 74

Selecting What Information to Log

Besides the standard information listed above, you can choose to log additional information. Those optional selections are as follows:

  • Attempted access to blocked site
  • Connections to the Web-based interface of the modem router
  • Modem Router operation (start up, get time, etc.)
  • Known DoS attacks and Port Scans

Saving Log Files on a Server

You can choose to write the logs to a computer running a syslog program. To activate this feature, select to Broadcast on Lan or enter the IP address of the server where the Syslog file will be written.

Examples of Log Messages

Following are examples of log messages. In all cases, the log entry shows the timestamp as: Day, Year-Month-Date Hour:Minute:Second.

Tue, 2002-05-21 18:48:39 - NETGEAR activated

[This entry indicates a power-up or reboot with initial time entry.]

Tue, 2002-05-21 18:55:00 - Administrator login successful - IP:192.168.0.2 Thu, 2002-05-21 18:56:58 - Administrator logout - IP:192.168.0.2

[This entry shows an administrator logging in and out from IP address 192.168.0.2.]

Tue, 2002-05-21 19:00:06 - Login screen timed out - IP:192.168.0.2

[This entry shows a time-out of the administrator login.]

Wed, 2002-05-22 22:00:19 - Log emailed

[This entry shows when the log was emailed.]

5-12 Managing Your Network

Activation and Administration

Page 75 of the NETGEAR DG834G user manual — Enabling Security Event E-mail Notification
Page 75 · click to enlarge
Page 75

Wed, 2002-05-22 07:15:15 - TCP packet dropped - Source:64.12.47.28,4787,WAN - Destination:134.177.0.11,21,LAN - [Inbound Default rule match] Sun, 2002-05-22 12:50:33 - UDP packet dropped - Source:64.12.47.28,10714,WAN - Destination:134.177.0.11,6970,LAN - [Inbound Default rule match] Sun, 2002-05-22 21:02:53 - ICMP packet dropped - Source:64.12.47.28,0,WAN - Destination:134.177.0.11,0,LAN - [Inbound Default rule match]

[These entries show an inbound FTP (port 21) packet, User Datagram Protocol (UDP) packet (port 6970), and Internet Control Message Protocol (ICMP) packet (port 0) being dropped as a result of the default inbound rule, which states that all inbound packets are denied.]

Enabling Security Event E-mail Notification

In order to receive logs and alerts by e-mail, you must provide your e-mail information in the E- mail subheading:

NETGEAR DG834G — Enabling Security Event E-mail Notification diagram (page 75)
Fig. 31 · Enabling Security Event E-mail Notification

Managing Your Network 5-13

Dropped Packets

Page 76 of the NETGEAR DG834G user manual — Enabling Security Event E-mail Notification
Page 76 · click to enlarge
Page 76
  • Turn e-mail notification on . Select this check box if you want to receive e-mail logs and alerts from the modem router.
  • Send alerts and logs via email .

— Send To This E-mail Address Enter the e-mail address where you want to send the alerts

and logs. Use a full e-mail address, such as ChrisXY@myISP.com.

— Outgoing Mail Server. Enter the name or IP address of the outgoing SMTP mail server of

your ISP (such as mail.myISP.com).

— Check My Mail Server requires authentication if you need to login to your SMTP

server to send E-mail. If you check this box, you must enter the user name and password for the mail server.

e-mail account, check the settings in your e-mail program.

  • Send alert immediately. Select the corresponding check box if you would like immediate notification of a significant security event, such as a known attack, port scan, or attempted access to a blocked site.
  • Send logs according to this schedule. Specifies how often to send the logs: Hourly, Daily, Weekly, or When Full.

– Day for sending log Specifies which day of the week to send the log. Relevant when the log is sent weekly or daily.

– Time for sending log Specifies the time of day to send the log. Relevant when the log is sent daily or weekly.

If the Weekly, Daily or Hourly option is selected and the log fills up before the specified period, the log is automatically e-mailed to the specified e-mail address. After the log is sent, it is cleared from the modem router’s memory. If the modem router cannot e-mail the log file, the log buffer may fill up. In this case, the modem router overwrites the log and discards its contents.

5-14 Managing Your Network

Page 77 of the NETGEAR DG834G user manual — Running Diagnostic Utilities and Rebooting the Modem Router
Page 77 · click to enlarge
Page 77

Running Diagnostic Utilities and Rebooting the Modem Router

The ADSL Modem Wireless Router has a diagnostics feature. You can use the diagnostics menu to perform the following functions from the modem router:

  • Ping an IP Address to test connectivity to see if you can reach a remote host.
  • Perform a DNS Lookup to test if an Internet name resolves to an IP address to verify that the DNS server configuration is working.
  • Display the Routing Table to identify what other modem routers the modem router is communicating with.
  • Reboot the modem router to enable new network configurations to take effect or to clear problems with the modem router’s network connection.

From the Main Menu of the browser interface, under the Maintenance heading, select the Modem Router Diagnostics heading to display the menu shown.

NETGEAR DG834G — Running Diagnostic Utilities and Rebooting the Modem Router diagram (page 77)
Fig. 32 · Running Diagnostic Utilities and Rebooting the Modem…

Managing Your Network 5-15

Page 78 of the NETGEAR DG834G user manual — Configuring Remote Management
Page 78 · click to enlarge
Page 78

Enabling Remote Management

Using the Remote Management page, you can allow a user or users on the Internet to configure, upgrade and check the status of your 54 Mbps ADSL Modem Wireless Router Model DG834G.

The ideal password should contain no dictionary words from any language, and should be a mixture of letters (both upper and lower case), numbers, and symbols. Your password can be up to 30 characters.

Configuring Remote Management

1. Log in to the modem router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever User Name, Password and LAN address you have chosen for the modem router.
2. From the Advanced section of the main menu, select the Remote Management link.
NETGEAR DG834G — Configuring Remote Management diagram (page 78)
Fig. 33 · Configuring Remote Management
3. Select the Turn Remote Management On check box.

5-16 Managing Your Network

Page 79 of the NETGEAR DG834G user manual — Enabling Remote Management
Page 79 · click to enlarge
Page 79
4. Specify what external addresses will be allowed to access the modem router’s remote management. For security, restrict access to as few external IP addresses as practical:
  • To allow access from any IP address on the Internet, select Everyone .
  • To allow access from a range of IP addresses on the Internet, select IP address range . Enter a beginning and ending IP address to define the allowed range.
  • To allow access from a single IP address on the Internet, select Only this Computer . Enter the IP address that will be allowed access.
5. Specify the Port Number that will be used for accessing the management interface.

Web browser access normally uses the standard HTTP service port 80. For greater security, you can change the remote management Web interface to a custom port by entering that number in the box provided. Choose a number between 1024 and 65535, but do not use the number of any common service port. The default is 8080, which is a common alternate for HTTP.

6. Click Apply to have your changes take effect.

When accessing your modem router from the Internet, you will type your modem router's WAN IP address in your browser's Address (in IE) or Location (in Netscape) box, followed by a colon (:) and the custom port number. For example, if your external address is 134.177.0.123 and you use port number 8080, enter in your browser:

http://134.177.0.123:8080

Managing Your Network 5-17

Page 80 of the NETGEAR DG834G user manual — Enabling Remote Management
Page 80 · click to enlarge
Page 80

5-18 Managing Your Network

Page 81 of the NETGEAR DG834G user manual — Configuring Advanced Security
Page 81 · click to enlarge
Page 81

Chapter 6 Advanced Configuration

This chapter describes how to configure the advanced features of your 54 Mbps ADSL Modem Wireless Router Model DG834G.

Configuring Advanced Security

The 54 Mbps ADSL Modem Wireless Router Model DG834G provides a variety of advanced features, such as:

  • Setting up a Demilitarized Zone (DMZ) Server
  • Connecting Automatically, as Required
  • Disabling Port Scan and DOS Protection
  • Responding to a Ping on the Internet WAN Port
  • MTU Size
  • Flexibility on configuring your LAN TCP/IP settings
  • Using the Router as a DHCP Server
  • Configuring Dynamic DNS
  • Configuring Static Routes

These features are discussed below.

Advanced Configuration 6-1

Page 82 of the NETGEAR DG834G user manual — Setting Up A Default DMZ Server
Page 82 · click to enlarge
Page 82

Setting Up A Default DMZ Server

The Default DMZ Server feature is helpful when using some online games and videoconferencing applications that are incompatible with NAT. The modem router is programmed to recognize some of these applications and to work properly with them, but there are other applications that may not function well. In some cases, one local computer can run the application properly if that computer’s IP address is entered as the Default DMZ Server.

When a computer is designated as the Default DMZ Server, it loses much of the protection of the firewall, and is exposed to many exploits from the Internet. If compromised, the computer can be used to attack your network.

Incoming traffic from the Internet is normally discarded by the modem router unless the traffic is a response to one of your local computers or a service that you have configured in the Ports menu. Instead of discarding this traffic, you can have it forwarded to one computer on your network. This computer is called the Default DMZ Server.

How to Configure a Default DMZ Server

To assign a computer or server to be a Default DMZ server, follow these steps:

1. Log in to the modem router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever Password and LAN address you have chosen for the modem router.

6-2 Advanced Configuration

Page 83 of the NETGEAR DG834G user manual — Disable Port Scan and DOS Protection
Page 83 · click to enlarge
Page 83
2. From the Main Menu, under Advanced, click the WAN Setup link to view the page shown:
NETGEAR DG834G — Connect Automatically, as Required diagram (page 83)
Fig. 34 · Connect Automatically, as Required
3. Select the Default DMZ Server check box.
4. Type the IP address for that server.
5. Click Apply to save your changes.

Connect Automatically, as Required

Normally, this option should be enabled, so that an Internet connection will be made automatically, whenever Internet-bound traffic is detected. If this causes high connection costs, you can disable this setting.

If disabled, you must connect manually, using the sub-screen accessed from the "Connection Status" button on the Status screen.

If you have an "Always on" connection, this setting has no effect.

Disable Port Scan and DOS Protection

The Firewall protects your LAN against Port Scans and Denial of Service (DOS) attacks. This should be disabled only in special circumstances.

Advanced Configuration 6-3

Page 84 of the NETGEAR DG834G user manual — Configuring LAN IP Settings
Page 84 · click to enlarge
Page 84

Respond to Ping on Internet WAN Port

If you want the modem router to respond to a 'ping' from the Internet, select the Respond to Ping on Internet WAN Port check box. This should only be used as a diagnostic tool, since it allows your modem router to be discovered. Do not select this box unless you have a specific reason to do so.

MTU Size

The normal MTU (Maximum Transmit Unit) value for most Ethernet networks is 1500 Bytes, or 1492 Bytes for PPPoE connections. For some ISPs you may need to reduce the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection.

Configuring LAN IP Settings

The LAN IP Setup menu allows configuration of LAN IP services such as DHCP and RIP. These features can be found under the Advanced heading in the Main Menu of the browser interface.

The modem router is shipped preconfigured to use private IP addresses on the LAN side, and to act as a DHCP server. The modem router’s default LAN IP configuration is:

  • LAN IP addresses—192.168.0.1
  • Subnet mask—255.255.255.0

6-4 Advanced Configuration

Page 85 of the NETGEAR DG834G user manual — Respond to Ping on Internet WAN Port
Page 85 · click to enlarge
Page 85

These addresses are part of the Internet Engineering Task Force (IETF)-designated private address range for use in private networks, and should be suitable in most applications. If your network has a requirement to use a different IP addressing scheme, you can make those changes in this menu.

NETGEAR DG834G — Respond to Ping on Internet WAN Port diagram (page 85)
Fig. 35 · Respond to Ping on Internet WAN Port

The LAN TCP/IP Setup parameters are:

  • IP Address This is the LAN IP address of the modem router.

through the browser, you or anyone else using the router will be disconnected. You must then open a new connection to the new IP address and log in again. Others using the router will have to restart their computer and connect to the router again.

  • IP Subnet Mask This is the LAN Subnet Mask of the modem router. Combined with the IP address, the IP Subnet Mask allows a device to know which other addresses are local to it, and which must be reached through a gateway or modem router.

Advanced Configuration 6-5

Page 86 of the NETGEAR DG834G user manual — DHCP
Page 86 · click to enlarge
Page 86
  • RIP Direction RIP (Router Information Protocol) allows a modem router to exchange routing information with other routers. The RIP Direction selection controls how the Modem Router sends and receives RIP packets. Both is the default.

— When set to Both or Out Only, the modem router will broadcast its routing table

periodically.

— When set to Both or In Only, it will incorporate the RIP information that it receives.

— When set to None, it will not send any RIP packets and will ignore any RIP packets

received.

  • RIP Version This controls the format and the broadcasting method of the RIP packets that the modem router sends. It recognizes both formats when receiving. By default, this is set for RIP-1.

— RIP-1 is universally supported. RIP-1 is probably adequate for most networks, unless you

have an unusual network setup.

— RIP-2 carries more information. Both RIP-2B and RIP-2M send the routing data in RIP-2

format.

– RIP-2B uses subnet broadcasting. – RIP-2M uses multicasting.

DHCP

By default, the modem router will function as a DHCP (Dynamic Host Configuration Protocol) server, allowing it to assign IP, DNS server, and default gateway addresses to all computers connected to the modem router's LAN. The assigned default gateway address is the LAN address of the router. IP addresses will be assigned to the attached PCs from a pool of addresses specified in this menu. Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN.

For most applications, the default DHCP and TCP/IP settings of the router are satisfactory. See “Internet Networking and TCP/IP Addressing” in Appendix C for an explanation of DHCP and information about how to assign IP addresses for your network.

Use Router as DHCP server

If another device on your network will be the DHCP server, or if you will manually configure the network settings of all of your computers, clear the ‘Use router as DHCP server’ check box. Otherwise, leave it selected.

6-6 Advanced Configuration

Page 87 of the NETGEAR DG834G user manual — DHCP
Page 87 · click to enlarge
Page 87

Specify the pool of IP addresses to be assigned by setting the Starting IP Address and Ending IP Address. These addresses should be part of the same IP address subnet as the router’s LAN IP address. Using the default addressing scheme, you should define a range between 192.168.0.2 and 192.168.0.254, although you may want to save part of the range for devices with fixed addresses.

The router will deliver the following parameters to any LAN device that requests DHCP:

  • An IP Address from the range you have defined
  • Subnet Mask
  • Gateway IP Address is the router’s LAN IP address
  • Primary DNS Server, if you entered a Primary DNS address in the Basic Settings menu; otherwise, the router’s LAN IP address
  • Secondary DNS Server, if you entered a Secondary DNS address in the Basic Settings menu
  • WINS Server, short for Windows Internet Naming Service Server, determines the IP address associated with a particular Windows computer. A WINS server records and reports a list of names and IP address of Windows PCs on its local network. If you connect to a remote network that contains a WINS server, enter the server’s IP address here. This allows your PCs to browse the network using the Network Neighborhood feature of Windows.

When you specify a reserved IP address for a computer on the LAN, that computer will always receive the same IP address each time it access the router’s DHCP server. Reserved IP addresses should be assigned to servers that require permanent IP settings.

To reserve an IP address:

1. Click the Add button.
2. In the IP Address box, type the IP address to assign to the computer or server. Choose an IP address from the router’s LAN subnet, such as 192.168.0.x.
3. Type the MAC Address of the computer or server.

address from the Attached Devices menu and paste it here.

Reserved IP addresses · Advanced Configuration 6-7

Page 88 of the NETGEAR DG834G user manual — How to Configure LAN TCP/IP Settings
Page 88 · click to enlarge
Page 88
4. Click Apply to enter the reserved address into the table.

contacts the router's DHCP server. Reboot the computer or access its IP configuration and force a DHCP release and renew.

To edit or delete a reserved address entry:

1. Click the button next to the reserved address you want to edit or delete.
2. Click Edit or Delete .

How to Configure LAN TCP/IP Settings

1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever User Name, Password and LAN address you have chosen for the router.
2. From the Main Menu, under Advanced, click the LAN IP Setup link to view the menu, shown:
3. Enter the TCP/IP, DHCP, or Reserved IP parameters.
4. Click Apply to save your changes.

6-8 Advanced Configuration

Page 89 of the NETGEAR DG834G user manual — How to Configure Dynamic DNS
Page 89 · click to enlarge
Page 89

Configuring Dynamic DNS

If your network has a permanently assigned IP address, you can register a domain name and have that name linked with your IP address by public Domain Name Servers (DNS). However, if your Internet account uses a dynamically assigned IP address, you will not know in advance what your IP address will be, and the address can change frequently. In this case, you can use a commercial dynamic DNS service that will allow you to register your domain to their IP address, and will forward traffic directed at your domain to your frequently-changing IP address.

The router contains a client that can connect to a dynamic DNS service provider. To use this feature, you must select a service provider and obtain an account with them. After you have configured your account information in the router, whenever your ISP-assigned IP address changes, your router will automatically contact your dynamic DNS service provider, log in to your account, and register your new IP address.

How to Configure Dynamic DNS

the dynamic DNS service will not work because private addresses will not be routed on the Internet.

1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever User Name, Password and LAN address you have chosen for the router.

Advanced Configuration 6-9

Page 90 of the NETGEAR DG834G user manual — Configuring Dynamic DNS
Page 90 · click to enlarge
Page 90
2. From the Main Menu of the browser interface, under Advanced, select Dynamic DNS to display the page below.
NETGEAR DG834G — Configuring Dynamic DNS diagram (page 90)
Fig. 36 · Configuring Dynamic DNS
3. Access the Web site of one of the dynamic DNS service providers whose names appear in the ‘Service Provider’ box, and register for an account. For example, for dyndns.org, go to www.dyndns.org
4. Select the Use a dynamic DNS service check box.
5. Select the name of your dynamic DNS Service Provider.
6. Type the Host Name that your dynamic DNS service provider gave you. The dynamic DNS service provider may call this the domain name. If your URL is myName.dyndns.org, then your Host Name is “myName.”
7. Type the User Name for your dynamic DNS account.
8. Type the Password (or key) for your dynamic DNS account.
9. If your dynamic DNS provider allows the use of wildcards in resolving your URL, you can select the Use wildcards check box to activate this feature. For example, the wildcard feature will cause *.yourhost.dyndns.org to be aliased to the same IP address as yourhost.dyndns.org
10. Click Apply to save your configuration.

6-10 Advanced Configuration

Page 91 of the NETGEAR DG834G user manual — Static Route Example
Page 91 · click to enlarge
Page 91

Using Static Routes

Static Routes provide additional routing information to your router. Under normal circumstances, the router has adequate routing information after it has been configured for Internet access, and you do not need to configure additional static routes. You must configure static routes only for unusual cases such as multiple routers or multiple IP subnets located on your network.

Static Route Example

As an example of when a static route is needed, consider the following case:

  • Your primary Internet access is through a cable modem to an ISP.
  • You have an ISDN router on your home network for connecting to the company where you are employed. This router’s address on your LAN is 192.168.0.100.
  • Your company’s network is 134.177.0.0.

When you first configured your router, two implicit static routes were created. A default route was created with your ISP as the modem router, and a second static route was created to your local network for all 192.168.0.x addresses. With this configuration, if you attempt to access a device on the 134.177.0.0 network, your router will forward your request to the ISP. The ISP forwards your request to the company where you are employed, and the request will likely be denied by the company’s firewall.

In this case you must define a static route, telling your router that 134.177.0.0 should be accessed through the ISDN router at 192.168.0.100. The static route would look like Figure 6-6.

In this example:

  • The Destination IP Address and IP Subnet Mask fields specify that this static route applies to all 134.177.x.x addresses.
  • The Modem Router IP Address fields specifies that all traffic for these addresses should be forwarded to the ISDN router at 192.168.0.100.
  • A Metric value of 1 will work since the ISDN router is on the LAN. This represents the number of routers between your network and the destination. This is a direct connection so it is set to 1.
  • Private is selected only as a precautionary security measure in case RIP is activated.

Advanced Configuration 6-11

Page 92 of the NETGEAR DG834G user manual — How to Configure Static Routes
Page 92 · click to enlarge
Page 92

How to Configure Static Routes

1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin , default password of password , or using whatever User Name, Password and LAN address you have chosen for the router.
2. From the Main Menu of the browser interface, under Advanced, click Static Routes to view the Static Routes menu, shown in Figure 6-5 .
NETGEAR DG834G — How to Configure Static Routes diagram (page 92)
Fig. 37 · How to Configure Static Routes
3. To add or edit a Static Route:

a. Click the Edit button to open the Edit Menu, shown in Figure 6-6.

NETGEAR DG834G — How to Configure Static Routes diagram (page 92)
Fig. 38 · How to Configure Static Routes

b. Type a route name for this static route in the Route Name box under the table. This is for identification purpose only.

c. Select Private if you want to limit access to the LAN only. The static route will not be reported in RIP.

6-12 Advanced Configuration

Page 93 of the NETGEAR DG834G user manual — Universal Plug and Play (UPnP)
Page 93 · click to enlarge
Page 93

d. Select Active to make this route effective.

e. Type the Destination IP Address of the final destination.

f. Type the IP Subnet Mask for this destination. If the destination is a single host, type 255.255.255.255.

g. Type the Gateway IP Address, which must be a router on the same LAN segment as the router.

h. Type a number between 1 and 15 as the Metric value. This represents the number of routers between your network and the destination. Usually, a setting of 2 or 3 works, but if this is a direct connection, set it to 1.

4. Click Apply to have the static route entered into the table.

Universal Plug and Play (UPnP)

Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers, access the network and connect to other devices as needed. UPnP devices can automatically discover the services from other registered UPnP devices on the network.

1. Click UPnP on the main menu to invoke the UPnP menu:
NETGEAR DG834G — Universal Plug and Play (UPnP) diagram (page 93)
Fig. 39 · Universal Plug and Play (UPnP)
2. Fill out the UPnP screen:
  • Turn UPnP On : UPnP can be enabled or disabled for automatic device configuration. The default setting for UPnP is enabled. If disabled, the Router will not allow any device to automatically control the resources, such as port forwarding (mapping), of the Router.

Advanced Configuration 6-13

Page 94 of the NETGEAR DG834G user manual — Universal Plug and Play (UPnP)
Page 94 · click to enlarge
Page 94
  • Advertisement Period : The Advertisement Period is how often the Router will advertise (broadcast) its UPnP information. This value can range from 1 to 1440 minutes. The default period is for 30 minutes. Shorter durations will ensure that control points have current device status at the expense of additional network traffic. Longer durations may compromise the freshness of the device status but can significantly reduce network traffic.
  • Advertisement Time To Live : The time to live for the advertisement is measured in hops (steps) for each UPnP packet sent. A hop is the number of steps allowed to propagate for each UPnP advertisement before it disappears. The number of hops can range from 1 to 255. The default value for the advertisement time to live is 4 hops, which should be fine for most home networks. If you notice that some devices are not being updated or reached correctly, then it may be necessary to increase this value a little.
  • UPnP Portmap Table : The UPnP Portmap Table displays the IP address of each UPnP device that is currently accessing the Router and which ports (Internal and External) that device has opened. The UPnP Portmap Table also displays what type of port is opened and if that port is still active for each IP address.
3. To save, cancel or refresh the table:

a. Click Apply to save the new settings to the Router.

b. Click Cancel to disregard any unsaved changes.

c. Click Refresh to update the portmap table and to show the active ports that are currently opened by UPnP devices.

6-14 Advanced Configuration

Page 95 of the NETGEAR DG834G user manual — Chapter 7 Virtual Private Networking
Page 95 · click to enlarge
Page 95

Chapter 7 Virtual Private Networking

This chapter describes how to use the virtual private networking (VPN) features of the ADSL Modem Wireless Router. VPN communications paths are called tunnels. VPN tunnels provide secure, encrypted communications between your local network and a remote network or computer. See “Virtual Private Networking (VPN)” in Appendix C to learn more about VPN.

This chapter is organized as follows:

  • “Overview of VPN Configuration” on page 7-2 provides an overview of the two most common VPN configurations: Client-to-Gateway and Gateway-to-Gateway.
  • “Planning a VPN” on page 7-4 provides a worksheet for recording the configuration parameters of the VPN you want to set up, along with the VPN Committee (VPNC) recommended default parameters set by the VPN Wizard.
  • “VPN Tunnel Configuration” on page 7-6 summarizes the three ways to configure a VPN tunnel: VPN Wizard (recommended for most situations), Auto Policy, and Manual Policy.
  • “How to Set Up a Client-to-Gateway VPN Configuration” on page 7-7 provides the steps needed to configure a VPN tunnel between a remote PC and a network gateway using the VPN Wizard and the NETGEAR ProSafe VPN Client.
  • “How to Set Up a Gateway-to-Gateway VPN Configuration” on page 7-21 provides the steps needed to configure a VPN tunnel between two network gateways using the VPN Wizard.
  • “VPN Tunnel Control” on page 7-29 provides the step-by-step procedures for activating, verifying, deactivating, and deleting a VPN tunnel once the VPN tunnel has been configured.
  • “How to Set Up VPN Tunnels in Special Circumstances” on page 7-38 provides the steps needed to configure VPN tunnels when there are special circumstances and the VPNC recommended defaults of the VPN Wizard are inappropriate. The two alternatives for configuring VPN tunnels are Auto Policy and Manual Policy.

Virtual Private Networking 7-1

Page 96 of the NETGEAR DG834G user manual — Overview of VPN Configuration
Page 96 · click to enlarge
Page 96

Overview of VPN Configuration

Two common scenarios for configuring VPN tunnels are between a remote personal computer and a network gateway and between two or more network gateways. The DG834G v3 supports both of these types of VPN configurations. The ADSL Modem Wireless Router supports up to five concurrent tunnels.

NETGEAR DG834G — Overview of VPN Configuration diagram (page 96)
Fig. 40 · Overview of VPN Configuration

Client-to-Gateway VPN Tunnels provide secure access from a remote PC, such as a telecommuter connecting to an office network.

A VPN client access allows a remote PC to connect to your network from any location on the Internet. In this case, the remote PC is one tunnel endpoint, running the VPN client software. The ADSL Modem Wireless Router on your network is the other tunnel endpoint. See “How to Set Up a Client-to-Gateway VPN Configuration” on page 7-7 to set up this configuration.

7-2 Virtual Private Networking

Page 97 of the NETGEAR DG834G user manual — Gateway-to-Gateway VPN Tunnels
Page 97 · click to enlarge
Page 97
NETGEAR DG834G — Gateway-to-Gateway VPN Tunnels diagram (page 97)
Fig. 41 · Gateway-to-Gateway VPN Tunnels
  • Gateway-to-Gateway VPN Tunnels provide secure access between networks, such as a branch or home office and a main office.

A VPN between two or more NETGEAR VPN-enabled routers is a good way to connect branch or home offices and business partners over the Internet. VPN tunnels also enable access to network resources across the Internet. In this case, use DG834G v3s on each end of the tunnel to form the VPN tunnel end points. See “How to Set Up a Gateway-to-Gateway VPN Configuration” on page 7-21 to set up this configuration.

Virtual Private Networking 7-3

Page 98 of the NETGEAR DG834G user manual — Planning a VPN
Page 98 · click to enlarge
Page 98

Planning a VPN

When you set up a VPN, it is helpful to plan the network configuration and record the configuration parameters on a worksheet:

Table 7-1. VPN Tunnel Configuration Worksheet

Connection Name:

Pre-Shared Key:

Secure Association -- Main Mode or Manual Keys:

Perfect Forward Secrecy -- Enabled or Disabled:

Encryption Protocol -- DES or 3DES:

Authentication Protocol -- MD5 or SHA-1:

Diffie-Hellman (DH) Group -- Group 1 or Group 2:

Key Life in seconds:

IKE Life Time in seconds:

FQDN or Gateway IP

VPN Endpoint Local IPSec ID LAN IP Address Subnet Mask

To set up a VPN connection, you must configure each endpoint with specific identification and connection information describing the other endpoint. You must configure the outbound VPN settings on one end to match the inbound VPN settings on other end, and vice versa.

This set of configuration information defines a security association (SA) between the two VPN endpoints. When planning your VPN, you must make a few choices first:

  • Will the local end be any device on the LAN, a portion of the local network (as defined by a subnet or by a range of IP addresses), or a single PC?
  • Will the remote end be any device on the remote LAN, a portion of the remote network (as defined by a subnet or by a range of IP addresses), or a single PC?

7-4 Virtual Private Networking

(WAN IP Address)

Page 99 of the NETGEAR DG834G user manual — Planning a VPN
Page 99 · click to enlarge
Page 99
  • Will either endpoint use Fully Qualified Domain Names (FQDNs)? FQDNs supplied by Dynamic DNS providers (see “The Use of a Fully Qualified Domain Name (FQDN)” on page B-8 ) can allow a VPN endpoint with a dynamic IP address to initiate or respond to a tunnel request. Otherwise, the side using a dynamic IP address must always be the initiator.
  • What method will you use to configure your VPN tunnels?

— The VPN Wizard using VPNC defaults (see Table 7-2)

— The typical automated Internet Key Exchange (IKE) setup (see “Using Auto Policy to

Configure VPN Tunnels” on page 7-38)

— A Manual Keying setup in which you must specify each phase of the connection (see

“Using Manual Policy to Configure VPN Tunnels” on page 7-48)?

Table 7-2. Parameters Recommended by the VPNC and Used in the VPN Wizard

Secure Association Main Mode

Authentication Method Pre-shared Key

Diffie-Hellman (DH) Group Group 2 (1024 bit)

Key Life 8 hours

IKE Life Time 1 hour

  • What level of IPSec VPN encryption will you use?

— DES - The Data Encryption Standard (DES) processes input data that is 64 bits wide,

encrypting these values using a 56 bit key. Faster but less secure than 3DES.

— 3DES - (Triple DES) achieves a higher level of security by encrypting the data three times

using DES with three different, unrelated keys.

  • What level of authentication will you use? — MDS: 128 bits, faster but less secure. — SHA-1: 160 bits, slower but more secure.

Virtual Private Networking 7-5

Parameter Factory Default · Encryption Method 3DES · Authentication Protocol SHA-1

Page 100 of the NETGEAR DG834G user manual — VPN Tunnel Configuration
Page 100 · click to enlarge
Page 100

VPN Tunnel Configuration

There are two tunnel configurations and three ways to configure them:

  • Use the VPN Wizard to configure a VPN tunnel (recommended for most situations):

— See “How to Set Up a Client-to-Gateway VPN Configuration” on page 7-7.

— See “How to Set Up a Gateway-to-Gateway VPN Configuration” on page 7-21.

  • See “Using Auto Policy to Configure VPN Tunnels” on page 7-38 when the VPN Wizard and its VPNC defaults (see Table 7-2 ) are not appropriate for your special circumstances, but you want to automate the Internet Key Exchange (IKE) setup.
  • See “Using Manual Policy to Configure VPN Tunnels” on page 7-48 when the VPN Wizard and its VPNC defaults (see Table 7-2 ) are not appropriate for your special circumstances and you must specify each phase of the connection. You manually enter all the authentication and key parameters. You have more control over the process, however the process is more complex and there are more opportunities for errors or configuration mismatches between your DG834G v3 and the corresponding VPN endpoint gateway or client workstation.

gateway and client software products. Look on the NETGEAR web site at www.netgear.com for these interoperability scenarios.

7-6 Virtual Private Networking

Page 101 of the NETGEAR DG834G user manual — Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v3
Page 101 · click to enlarge
Page 101
NETGEAR DG834G — How to Set Up a Client-to-Gateway VPN Configuration diagram (page 101)
Fig. 42 · How to Set Up a Client-to-Gateway VPN Configuration

Setting up a VPN between a remote PC running the NETGEAR ProSafe VPN Client and a network gateway involves the following two steps:

  • “Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v3” on page 7-7 uses the VPN Wizard to configure the VPN tunnel between the remote PC and network gateway.
  • “Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC” on page 7-12 configures the NETGEAR ProSafe VPN Client endpoint.

Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v3

NETGEAR DG834G — Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v3 diagram (page 101)
Fig. 43 · Step 1: Configuring the Client-to-Gateway VPN Tunnel…

default parameters listed in Table 7-2 on page 7-5. If you have special requirements not covered by these VPNC-recommended parameters, refer to “How to Set Up VPN Tunnels in Special Circumstances” on page 7-38 to set up the VPN tunnel.

The worksheet below identifies the parameters used in the following procedure. A blank worksheet is at “Planning a VPN” on page 7-4.

Virtual Private Networking 7-7

Page 102 of the NETGEAR DG834G user manual — How to Set Up a Client-to-Gateway VPN Configuration
Page 102 · click to enlarge
Page 102

Table 7-3. VPN Tunnel Configuration Worksheet

Connection NameRoadWarrior
Pre-Shared Key12345678

Secure Association -- Main Mode or Manual Keys: Main

Perfect Forward Secrecy -- Enabled or Disabled: Disabled

Encryption Protocol -- DES or 3DES: 3DES

Authentication Protocol -- MD5 or SHA-1: SHA-1

Diffie-Hellman (DH) Group -- Group 1 or Group 2: Group 2

Key Life in seconds28800 (8 hours)
IKE Life Time in seconds3600 (1 hour)

FQDN or Gateway IP

VPN Endpoint Local IPSec ID LAN IP Address Subnet Mask

Client toDG834 — — Dynamic

DG834G v3 toClient 192.168.3.1 255.255.255.0 22.23.24.25

Follow this procedure to configure a client-to-gateway VPN tunnel using the VPN Wizard.

7-8 Virtual Private Networking

(WAN IP Address)

Page 103 of the NETGEAR DG834G user manual — How to Set Up a Client-to-Gateway VPN Configuration
Page 103 · click to enlarge
Page 103
1. Log in to the DG834G v3 at its LAN address of http://192.168.0.1 with its default user name of admin and password of password . Click the VPN Wizard link in the main menu to display this screen. Click Next to proceed.
NETGEAR DG834G — How to Set Up a Client-to-Gateway VPN Configuration diagram (page 103)
Fig. 44 · How to Set Up a Client-to-Gateway VPN Configuration
2. Fill in the Connection Name and the pre-shared key, select the type of target end point, and click Next to proceed.
NETGEAR DG834G — How to Set Up a Client-to-Gateway VPN Configuration diagram (page 103)
Fig. 45 · How to Set Up a Client-to-Gateway VPN Configuration
Enter the new Connection Name(e.g., RoadWarrior )
Enter the pre-shared key(e.g., 12345678 )
Select the radio buttonA remote VPN client (single PC)

functions.

Virtual Private Networking 7-9

Page 104 of the NETGEAR DG834G user manual — How to Set Up a Client-to-Gateway VPN Configuration
Page 104 · click to enlarge
Page 104

The Summary screen below displays.

NETGEAR DG834G — How to Set Up a Client-to-Gateway VPN Configuration diagram (page 104)
Fig. 46 · How to Set Up a Client-to-Gateway VPN Configuration

7-10 Virtual Private Networking

Page 105 of the NETGEAR DG834G user manual — How to Set Up a Client-to-Gateway VPN Configuration
Page 105 · click to enlarge
Page 105

To view the VPNC recommended authentication and encryption settings used by the VPN Wizard, click the “here” link. Click Back to return to the Summary screen.

NETGEAR DG834G — How to Set Up a Client-to-Gateway VPN Configuration diagram (page 105)
Fig. 47 · How to Set Up a Client-to-Gateway VPN Configuration
3. Click Done on the Summary screen to complete the configuration procedure. The VPN Policies menu below displays showing that the new tunnel is enabled.
NETGEAR DG834G — How to Set Up a Client-to-Gateway VPN Configuration diagram (page 105)
Fig. 48 · How to Set Up a Client-to-Gateway VPN Configuration

Virtual Private Networking 7-11

1 hour

Page 106 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC
Page 106 · click to enlarge
Page 106

To view or modify the tunnel settings, select the radio button next to the tunnel entry and click Edit.

the IKE keepalive capability on an existing VPN tunnel.

Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC

This procedure describes how to configure the NETGEAR ProSafe VPN Client. We will assume the PC running the client has a dynamically assigned IP address.

The PC must have the NETGEAR ProSafe VPN Client program installed that supports IPSec. Go to the NETGEAR website (http://www.netgear.com) and select VPN01L_VPN05L in the Product Quick Find drop-down menu for information on how to purchase the NETGEAR ProSafe VPN Client.

any virus protection or firewall software you may be running on your PC.

  • 1. Install the NETGEAR ProSafe VPN Client on the remote PC and reboot.
  • You may need to insert your Windows CD to complete the installation.
  • If you do not have a modem or dial-up adapter installed in your PC, you may see the warning message stating “The NETGEAR ProSafe VPN Component requires at least one dial-up adapter be installed.” You can disregard this message.
  • Install the IPSec Component. You may have the option to install either the VPN Adapter or the IPSec Component or both. The VPN Adapter is not necessary.
  • The system should show the ProSafe icon ( ) in the system tray after rebooting.
  • Double-click the system tray icon to open the Security Policy Editor.
2. Add a new connection.

a. Run the NETGEAR ProSafe Security Policy Editor program and, using the “VPN Tunnel Configuration Worksheet” on page 7-8, create a VPN Connection.

7-12 Virtual Private Networking

Page 107 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC
Page 107 · click to enlarge
Page 107

b. From the Edit menu of the Security Policy Editor, click Add, then Connection.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC diagram (page 107)
Fig. 49 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

A “New Connection” listing appears in the list of policies. Rename the “New Connection” so that it matches the Connection Name you entered in the VPN Settings of the DG834G v3 on LAN A.

tunnel is toDG834 and it does not have to match the RoadWarrior Connection Name used on the gateway side of the VPN tunnel because Connection Names are arbitrary to how the VPN tunnel functions.

administering the VPN.

c. Select Secure in the Connection Security check-box group.

d. Select IP Subnet in the ID Type menu.

e. In this example, type 192.168.3.1 in the Subnet field as the network address of the DG834G v3.

f. Enter 255.255.255.0 in the Mask field as the LAN Subnet Mask of the DG834G v3.

g. Select All in the Protocol menu to allow all traffic through the VPN tunnel.

Virtual Private Networking 7-13

Page 108 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC
Page 108 · click to enlarge
Page 108

h. Select the Connect using Secure Gateway Tunnel check box.

i. Select IP Address in the ID Type menu below the check box.

j. Enter the public WAN IP Address of the DG834G v3 in the field directly below the ID Type menu. In this example, 22.23.24.25 would be used.

k. The resulting Connection Settings are shown in Figure 7-10.

3. Configure the Security Policy in the NETGEAR ProSafe VPN Client software:

a. In the Network Security Policy list, expand the new connection by double clicking its name or clicking on the “+” symbol. My Identity and Security Policy subheadings appear below the connection name.

b. Click on the Security Policy subheading to show the Security Policy menu.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC diagram (page 108)
Fig. 50 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

c. Select the Main Mode in the Select Phase 1 Negotiation Mode check-box group.

4. Configure the VPN Client Identity.

In this step, you will provide information about the remote VPN client PC. You will need to provide the Pre-Shared Key that you configured in the DG834G v3 and either a fixed IP address or a “fixed virtual” IP address of the VPN client PC.

7-14 Virtual Private Networking

Page 109 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC
Page 109 · click to enlarge
Page 109

a. In the Network Security Policy list on the left side of the Security Policy Editor window, click on My Identity.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC diagram (page 109)
Fig. 51 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

b. Choose None in the Select Certificate menu.

c. Select IP Address in the ID Type menu. If you are using a virtual fixed IP address, enter this address in the Internal Network IP Address box. Otherwise, leave this box empty.

d. In the Internet Interface box, select the adapter you use to access the Internet. Select PPP Adapter in the Name menu if you have a dial-up Internet account. Select your Ethernet adapter if you have a dedicated Cable or DSL line. You may also choose Any if you will be switching between adapters or if you have only one adapter.

Virtual Private Networking 7-15

Page 110 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC
Page 110 · click to enlarge
Page 110

e. Click the Pre-Shared Key button. In the Pre-Shared Key dialog box, click the Enter Key button. Enter the DG834G v3's Pre-Shared Key and click OK. In this example, 12345678 is entered. This field is case sensitive.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC diagram (page 110)
Fig. 52 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…
5. Configure the VPN Client Authentication Proposal.

In this step, you will provide the type of encryption (DES or 3DES) to be used for this connection. This selection must match your selection in the DG834G v3 configuration.

a. In the Network Security Policy list on the left side of the Security Policy Editor window, expand the Security Policy heading by double clicking its name or clicking on the “+” symbol.

b. Expand the Authentication subheading by double clicking its name or clicking on the “+” symbol. Then select Proposal 1 below Authentication.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC diagram (page 110)
Fig. 53 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

7-16 Virtual Private Networking

Page 111 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC
Page 111 · click to enlarge
Page 111

c. In the Authentication Method menu, select Pre-Shared key.

d. In the Encrypt Alg menu, select the type of encryption to correspond with what was configured for the Encryption Protocol in the DG834G v3 in Table 7-3 on page 7-8. In this example, use Triple DES.

e. In the Hash Alg menu, select SHA-1.

f. In the SA Life menu, select Unspecified.

g. In the Key Group menu, select Diffie-Hellman Group 2.

6. Configure the VPN Client Key Exchange Proposal.

In this step, you will provide the type of encryption (DES or 3DES) to be used for this connection. This selection must match your selection in the DG834G v3 configuration.

a. Expand the Key Exchange subheading by double clicking its name or clicking on the “+” symbol. Then select Proposal 1 below Key Exchange.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC diagram (page 111)
Fig. 54 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

b. In the SA Life menu, select Unspecified.

c. In the Compression menu, select None.

d. Check the Encapsulation Protocol (ESP) checkbox.

e. In the Encrypt Alg menu, select the type of encryption to correspond with what was configured for the Encryption Protocol in the DG834G v3 in Table 7-3 on page 7-8. In this example, use Triple DES.

Virtual Private Networking 7-17

Page 112 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC
Page 112 · click to enlarge
Page 112

f. In the Hash Alg menu, select SHA-1.

g. In the Encapsulation menu, select Tunnel.

h. Leave the Authentication Protocol (AH) checkbox unchecked.

7. Save the VPN Client Settings.

From the File menu at the top of the Security Policy Editor window, select Save.

After you have configured and saved the VPN client information, your PC will automatically open the VPN connection when you attempt to access any IP addresses in the range of the remote VPN router’s LAN.

8. Check the VPN Connection.

To check the VPN Connection, you can initiate a request from the remote PC to the DG834G v3’s network by using the “Connect” option in the NETGEAR ProSafe menu bar. The NETGEAR ProSafe client will report the results of the attempt to connect. Since the remote PC has a dynamically assigned WAN IP address, it must initiate the request.

To perform a ping test using our example, start from the remote PC:

a. Establish an Internet connection from the PC.

b. On the Windows taskbar, click the Start button, and then click Run.

c. Type ping -t 192.168.3.1, and then click OK.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC diagram (page 112)
Fig. 55 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

7-18 Virtual Private Networking

Page 113 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC
Page 113 · click to enlarge
Page 113

This will cause a continuous ping to be sent to the first DG834G v3. After between several seconds and two minutes, the ping response should change from “timed out” to “reply.”

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC diagram (page 113)
Fig. 56 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

Once the connection is established, you can open the browser of the PC and enter the LAN IP address of the remote DG834G v3. After a short wait, you should see the login screen of the Modem Router (unless another PC already has the DG834G v3 management interface open).

Information on the progress and status of the VPN client connection can be viewed by opening the NETGEAR ProSafe Log Viewer.

To launch this function, click on the Windows Start button, then select Programs, then NETGEAR ProSafe VPN Client, then Log Viewer. The Log Viewer screen for a successful connection is shown below:

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC diagram (page 113)
Fig. 57 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

connection is due to the VPN tunnel or some reason outside the VPN tunnel.

Virtual Private Networking 7-19

Page 114 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC
Page 114 · click to enlarge
Page 114
9. The Connection Monitor screen for this connection is shown below:
NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC diagram (page 114)
Fig. 58 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

In this example you can see the following:

  • The DG834G v3 has a public IP WAN address of 22.23.24.25.
  • The DG834G v3 has a LAN IP address of 192.168.3.1.
  • The VPN client PC has a dynamically assigned address of 192.168.2.2.

While the connection is being established, the Connection Name field in this menu will say “SA” before the name of the connection. When the connection is successful, the “SA” will change to the yellow key symbol shown in the illustration above.

normal Internet access. If this is the case, you will need to close the VPN connection in order to have normal Internet access.

7-20 Virtual Private Networking

Page 115 of the NETGEAR DG834G user manual — A B VPN Tunnel
Page 115 · click to enlarge
Page 115

How to Set Up a Gateway-to-Gateway VPN Configuration

default parameters listed in Table 7-2 on page 7-5. If you have special requirements not covered by these VPNC-recommended parameters, refer to “How to Set Up VPN Tunnels in Special Circumstances” on page 7-38 to set up the VPN tunnel.

Follow this procedure to configure a gateway-to-gateway VPN tunnel using the VPN Wizard.

A B VPN Tunnel

14.15.16.17 22.23.24.25

DG834G VPN Firewall DG834G VPN Firewall

192.168.0.1 192.168.3.1

Set the LAN IPs on each DG834G v3 to different subnets and configure each properly for the Internet. The examples below assume the following settings:

Virtual Private Networking 7-21

PCs PCs

Page 116 of the NETGEAR DG834G user manual — How to Set Up a Gateway-to-Gateway VPN Configuration
Page 116 · click to enlarge
Page 116

Table 7-4. VPN Tunnel Configuration Worksheet

Connection NameGtoG
Pre-Shared Key12345678

Secure Association -- Main Mode or Manual Keys: Main

Perfect Forward Secrecy -- Enabled or Disabled: Disabled

Encryption Protocol -- DES or 3DES: 3DES

Authentication Protocol -- MD5 or SHA-1: SHA-1

Diffie-Hellman (DH) Group -- Group 1 or Group 2: Group 2

Key Life in seconds28800 (8 hours)
IKE Life Time in seconds3600 (1 hour)

FQDN or Gateway IP

VPN Endpoint Local IPSec ID LAN IP Address Subnet Mask

DG834G v3_A GW_A 192.168.0.1 255.255.255.0 14.15.16.17

DG834G v3_B GW_B 192.168.3.1 255.255.255.0 22.23.24.25

connection will fail if both are using the NETGEAR default address range of 192.168.0.x.

Follow this procedure to configure a gateway-to-gateway VPN tunnel using the VPN Wizard.

1. Log in to the DG834G v3 on LAN A at its default LAN address of http://192.168.0.1 with its default user name of admin and password of password . Click the VPN Wizard link in the main menu to display this screen. Click Next to proceed.

7-22 Virtual Private Networking

(WAN IP Address)

Page 117 of the NETGEAR DG834G user manual — How to Set Up a Gateway-to-Gateway VPN Configuration
Page 117 · click to enlarge
Page 117
2. Fill in the Connection Name and the pre-shared key, select the type of target end point, and click Next to proceed.
NETGEAR DG834G — How to Set Up a Gateway-to-Gateway VPN Configuration diagram (page 117)
Fig. 59 · How to Set Up a Gateway-to-Gateway VPN Configuration
Enter the new Connection Name(e.g., GtoG )
Enter the pre-shared key(e.g., 12345678 )
Select the radio buttonA remote VPN Gateway

Virtual Private Networking 7-23

Page 118 of the NETGEAR DG834G user manual — How to Set Up a Gateway-to-Gateway VPN Configuration
Page 118 · click to enlarge
Page 118
3. Fill in the IP Address or FQDN for the target VPN endpoint WAN connection and click Next .
NETGEAR DG834G — How to Set Up a Gateway-to-Gateway VPN Configuration diagram (page 118)
Fig. 60 · How to Set Up a Gateway-to-Gateway VPN Configuration

Enter the WAN IP address of the remote VPN gateway: (e.g., 22.23.24.25)

4. Identify the IP addresses at the target endpoint which can use this tunnel, and click Next .

Enter the LAN IP settings of the remote VPN gateway:

NETGEAR DG834G — How to Set Up a Gateway-to-Gateway VPN Configuration diagram (page 118)
Fig. 61 · How to Set Up a Gateway-to-Gateway VPN Configuration
  • IP Address (e.g., 192.168.3.1 )
  • Subnet Mask (e.g., 255.255.255.0 )

7-24 Virtual Private Networking

Page 119 of the NETGEAR DG834G user manual — How to Set Up a Gateway-to-Gateway VPN Configuration
Page 119 · click to enlarge
Page 119

The Summary screen below displays.

NETGEAR DG834G — How to Set Up a Gateway-to-Gateway VPN Configuration diagram (page 119)
Fig. 62 · How to Set Up a Gateway-to-Gateway VPN Configuration

Virtual Private Networking 7-25

Page 120 of the NETGEAR DG834G user manual — How to Set Up a Gateway-to-Gateway VPN Configuration
Page 120 · click to enlarge
Page 120

To view the VPNC recommended authentication and encryption settings used by the VPN Wizard, click the “here” link (see Figure 7-24). Click Back to return to the Summary screen.

5. Click Done on the Summary screen (see Figure 7-24 ) to complete the configuration procedure. The VPN Settings menu below displays showing that the new tunnel is enabled.
NETGEAR DG834G — How to Set Up a Gateway-to-Gateway VPN Configuration diagram (page 120)
Fig. 63 · How to Set Up a Gateway-to-Gateway VPN Configuration

7-26 Virtual Private Networking

1 hour

Page 121 of the NETGEAR DG834G user manual — How to Set Up a Gateway-to-Gateway VPN Configuration
Page 121 · click to enlarge
Page 121

enable the IKE keepalive capability on an existing VPN tunnel.

6. Repeat for the DG834G v3 on LAN B and pay special attention to use the following network settings as appropriate.
  • WAN IP of the remote VPN gateway (e.g., 14.15.16.17 )
  • LAN IP settings of the remote VPN gateway:

— IP Address (e.g, 192.168.0.1)

— Subnet Mask (e.g., 255.255.255.0)

— Preshared Key (e.g., 12345678)

7. Use the VPN Status screen to activate the VPN tunnel by performing the following steps:

“Activating a VPN Tunnel” on page 7-29 for information on the other ways.

Virtual Private Networking 7-27

Page 122 of the NETGEAR DG834G user manual — How to Set Up a Gateway-to-Gateway VPN Configuration
Page 122 · click to enlarge
Page 122

a. Open the DG834G v3 management interface and click on VPN Status to get the VPN Status/Log screen (Figure 7-27).

NETGEAR DG834G — How to Set Up a Gateway-to-Gateway VPN Configuration diagram (page 122)
Fig. 64 · How to Set Up a Gateway-to-Gateway VPN Configuration

b. Click on VPN Status (Figure 7-29) to get the Current VPN Tunnels (SAs) screen (Figure 7-28). Click on Connect for the VPN tunnel you want to activate.

NETGEAR DG834G — How to Set Up a Gateway-to-Gateway VPN Configuration diagram (page 122)
Fig. 65 · How to Set Up a Gateway-to-Gateway VPN Configuration

c. Look at the VPN Status/Log screen (Figure 7-27) to verify that the tunnel is connected.

7-28 Virtual Private Networking

Page 123 of the NETGEAR DG834G user manual — Activating a VPN Tunnel
Page 123 · click to enlarge
Page 123

VPN Tunnel Control

Activating a VPN Tunnel

There are three ways to activate a VPN tunnel:

  • Use the VPN Status page.
  • Activate the VPN tunnel by pinging the remote endpoint.
  • Start using the VPN tunnel.

the IKE keepalive capability on an existing VPN tunnel.

Using the VPN Status Page to Activate a VPN Tunnel

To use the VPN Status screen to activate a VPN tunnel, perform the following steps:

1. Log in to the Modem Router.
2. Open the DG834G v3 management interface and click on VPN Status to get the VPN Status/ Log screen ( Figure 7-29 ).

Virtual Private Networking 7-29

Page 124 of the NETGEAR DG834G user manual — VPN Tunnel Control
Page 124 · click to enlarge
Page 124
3. Click on VPN Status ( Figure 7-29 ) to get the Current VPN Tunnels (SAs) screen ( Figure 7-30 ). Click on Connect for the VPN tunnel you want to activate.
NETGEAR DG834G — VPN Tunnel Control diagram (page 124)
Fig. 66 · VPN Tunnel Control

Activate the VPN Tunnel by Pinging the Remote Endpoint

To activate the VPN tunnel by pinging the remote endpoint (e.g., 192.168.3.1), do the following steps depending on whether your configuration is client-to-gateway or gateway-to-gateway:

  • Client-to-Gateway Configuration —to check the VPN Connection, you can initiate a request from the remote PC to the DG834G v3’s network by using the “Connect” option in the NETGEAR ProSafe menu bar. The NETGEAR ProSafe client will report the results of the attempt to connect. Since the remote PC has a dynamically assigned WAN IP address, it must initiate the request.

To perform a ping test using our example, start from the remote PC:

a. Establish an Internet connection from the PC.

b. On the Windows taskbar, click the Start button, and then click Run.

c. Type ping -t 192.168.3.1 and then click OK.

7-30 Virtual Private Networking

Page 125 of the NETGEAR DG834G user manual — VPN Tunnel Control
Page 125 · click to enlarge
Page 125
Figure 7-31Running a Ping test to the LAN from the PC

This will cause a continuous ping to be sent to the first DG834G v3. After between several seconds and two minutes, the ping response should change from “timed out” to “reply.”

Once the connection is established, you can open the browser of the PC and enter the LAN IP address of the remote DG834G v3. After a short wait, you should see the login screen of the Modem Router (unless another PC already has the DG834G v3 management interface open).

  • Gateway-to-Gateway Configuration —test the VPN tunnel by pinging the remote network from a PC attached to the DG834G v3.

a. Open command prompt (i.e., Start -> Run -> cmd).

Virtual Private Networking 7-31

Page 126 of the NETGEAR DG834G user manual — VPN Tunnel Control
Page 126 · click to enlarge
Page 126

b. ping 192.168.3.1.

NETGEAR DG834G — VPN Tunnel Control diagram (page 126)
Fig. 67 · VPN Tunnel Control

Start Using a VPN Tunnel to Activate It

To use a VPN tunnel, use a Web browser to go to a URL whose IP address or range is covered by the policy for that VPN tunnel.

7-32 Virtual Private Networking

Page 127 of the NETGEAR DG834G user manual — Verifying the Status of a VPN Tunnel
Page 127 · click to enlarge
Page 127

Verifying the Status of a VPN Tunnel

To use the VPN Status page to determine the status of a VPN tunnel, perform the following steps:

1. Log in to the Modem Router.
2. Open the DG834G v3 management interface and click on VPN Status to get the VPN Status/ Log screen ( Figure 7-34 ).

Log—this log shows the details of recent VPN activity, including the building of the VPN tunnel. If there is a problem with the VPN tunnel, refer to the log for information about what might be the cause of the problem.

  • Click Refresh to see the most recent entries.
  • Click Clear Log to delete all log entries.

Virtual Private Networking 7-33

Page 128 of the NETGEAR DG834G user manual — Verifying the Status of a VPN Tunnel
Page 128 · click to enlarge
Page 128
3. Click on VPN Status ( Figure 7-29 ) to get the Current VPN Tunnels (SAs) screen.
NETGEAR DG834G — Verifying the Status of a VPN Tunnel diagram (page 128)
Fig. 68 · Verifying the Status of a VPN Tunnel

This table lists the following data for each active VPN Tunnel.

  • SPI —each SA has a unique SPI (Security Parameter Index) for traffic in each direction. For "Manual" key exchange, the SPI is specified in the Policy definition. For "Automatic" key exchange, the SPI is generated by the IKE protocol.
  • Policy Name —the name of the VPN policy associated with this SA.
  • Remote Endpoint —the IP address on the remote VPN Endpoint.
  • Action —the action will be either a "Drop" or a "Connect" button.
  • SLifeTime (Secs) —the remaining Soft Lifetime for this SA in seconds. When the Soft Lifetime becomes zero, the SA (Security Association) will re-negotiated.
  • HLifeTime (Secs) —the remaining Hard Lifetime for this SA in seconds. When the Hard Lifetime becomes zero, the SA (Security Association) will be terminated. (It will be reestablished if required.)

7-34 Virtual Private Networking

Page 129 of the NETGEAR DG834G user manual — Deactivating a VPN Tunnel
Page 129 · click to enlarge
Page 129

Deactivating a VPN Tunnel

Sometimes a VPN tunnel must be deactivated for testing purposes. There are two ways to deactivate a VPN tunnel:

  • Policy table on VPN Policies page
  • VPN Status page

Using the Policy Table on the VPN Policies Page to Deactivate a VPN Tunnel

To use the VPN Policies page to deactivate a VPN tunnel, perform the following steps:

1. Log in to the Modem Router.
2. Open the DG834G v3 management interface and click on VPN Policies to get the VPN Policies screen ( Figure 7-36 ).
3. Clear the Enable check box for the VPN tunnel you want to deactivate and click Apply . (To reactivate the tunnel, check the Enable box and click Apply .)

Using the VPN Status Page to Deactivate a VPN Tunnel

To use the VPN Status page to deactivate a VPN tunnel, perform the following steps:

1. Log in to the Modem Router.

Virtual Private Networking 7-35

Page 130 of the NETGEAR DG834G user manual — Deactivating a VPN Tunnel
Page 130 · click to enlarge
Page 130
2. Open the DG834G v3 management interface and click on VPN Status to get the VPN Status/ Log screen ( Figure 7-37 ).
3. Click VPN Status ( Figure 7-37 ) to get the Current VPN Tunnels (SAs) screen ( Figure 7-38 ). Click Drop for the VPN tunnel you want to deactivate.

7-36 Virtual Private Networking

Page 131 of the NETGEAR DG834G user manual — Deleting a VPN Tunnel
Page 131 · click to enlarge
Page 131

Deleting a VPN Tunnel

To delete a VPN tunnel:

1. Log in to the Modem Router.
2. Open the DG834G v3 management interface and click VPN Policies to display the VPN Policies screen ( Figure 7-39 ). Select the radio button for the VPN tunnel to be deleted and click the Delete button.

Virtual Private Networking 7-37

Page 132 of the NETGEAR DG834G user manual — Using Auto Policy to Configure VPN Tunnels
Page 132 · click to enlarge
Page 132

How to Set Up VPN Tunnels in Special Circumstances

When the VPN Wizard and its VPNC defaults (see Table 7-2) are not appropriate for your special circumstances, use one of the following alternatives:

  • Auto Policy —for a typical automated Internet Key Exchange (IKE) setup, see “Using Auto Policy to Configure VPN Tunnels” on page 7-38 . Auto Policy uses the IKE protocol to define the authentication scheme and automatically generate the encryption keys.
  • Manual Policy —for a Manual Keying setup in which you must specify each phase of the connection, see “Using Manual Policy to Configure VPN Tunnels” on page 7-48 . Manual Policy does not use IKE. Rather, you manually enter all the authentication and key parameters. You have more control over the process, however the process is more complex and there are more opportunities for errors or configuration mismatches between your DG834G v3 and the corresponding VPN endpoint gateway or client workstation.

Using Auto Policy to Configure VPN Tunnels

You need to configure matching VPN settings on both VPN endpoints. The outbound VPN settings on one end must match to the inbound VPN settings on other end, and vice versa.

See “Example of Using Auto Policy” on page 7-43 for an example of using Auto Policy.

Configuring VPN Network Connection Parameters

All VPN tunnels on the ADSL Modem Wireless Router require configuring several network parameters. This section describes those parameters and how to access them.

The most common configuration scenarios will use IKE to manage the authentication and encryption keys. The IKE protocol performs negotiations between the two VPN endpoints to automatically generate and update the required encryption parameters.

Click the VPN Policies link of the main menu, and then click the Add Auto Policy button to display the VPN - Auto Policy menu shown in Figure 7-40.

7-38 Virtual Private Networking

Page 133 of the NETGEAR DG834G user manual — How to Set Up VPN Tunnels in Special Circumstances
Page 133 · click to enlarge
Page 133
NETGEAR DG834G — How to Set Up VPN Tunnels in Special Circumstances diagram (page 133)
Fig. 69 · How to Set Up VPN Tunnels in Special Circumstances
NETGEAR DG834G — How to Set Up VPN Tunnels in Special Circumstances diagram (page 133)
Fig. 70 · How to Set Up VPN Tunnels in Special Circumstances

Virtual Private Networking 7-39

Page 134 of the NETGEAR DG834G user manual — How to Set Up VPN Tunnels in Special Circumstances
Page 134 · click to enlarge
Page 134

The DG834G v3 VPN tunnel network connection fields are defined as follows:

General. These settings identify this policy and determine its major characteristics.

  • Policy Name —Enter a unique name to identify this policy. This name is not supplied to the remote VPN endpoint. It is used only to help you manage the policies.
  • Remote VPN Endpoint —If the remote endpoint has a dynamic IP address, select Dynamic IP address . No "Address Data" input is required. You can set up multiple remote dynamic IP policies, but only one such policy can be enabled at a time. Otherwise, select the desired option (IP address or Domain Name) and enter the address of the remote VPN endpoint to which you wish to connect.

its "Remote VPN Endpoint".

  • IKE Keep-alive —Enable this if you wish to ensure that a connection is kept open, or, if that is not possible, that it is quickly re-established when disconnected.

The Ping IP Address must be associated with the remote endpoint. The remote LAN address must be used. This IP address will be "pinged" periodically to generate traffic for the VPN tunnel. The remote keep-alive IP address must be covered by the remote LAN IP range and must correspond to a device that can respond to ping. The range should be made as narrow as possible to meet this objective.

Local LAN. This identifies which PCs on your LAN are covered by this policy. For each selection, data must be provided as follows:

  • Single address —enter an IP address in the "Single/Start IP address" field. Typically, this setting is used when you wish to make a single Server on your LAN available to remote users.
  • Range address —enter the starting IP address in the "Single/Start IP address" field, and the finish IP address in the "Finish IP address" field. This must be an address range used on your LAN.
  • Subnet address —enter an IP address in the "Single/Start IP address" field, and the desired network mask in the "Subnet Mask" field. The remote VPN endpoint must have these IP addresses entered as its "Remote" addresses.

Remote LAN. This identifies which PCs on the remote LAN are covered by this policy. For each selection, data must be provided as follows:

7-40 Virtual Private Networking

Page 135 of the NETGEAR DG834G user manual — How to Set Up VPN Tunnels in Special Circumstances
Page 135 · click to enlarge
Page 135
  • Single PC - no Subnet — select this option if there is no LAN (only a single PC) at the remote endpoint. If this option is selected, no additional data is required. The typical application is a PC running the VPN client at the remote end.
  • Single address — Enter an IP address in the "Single/Start IP address" field. This must be an address on the remote LAN. Typically, this setting is used when you wish to access a server on the remote LAN.
  • Range address — enter the starting IP address in the "Single/Start IP address" field, and the finish IP address in the "Finish IP address" field. This must be an address range used on the remote LAN.
  • Subnet address — enter an IP address in the "Single/Start IP address" field, and the desired network mask in the "Subnet Mask" field.

The remote VPN endpoint must have these IP addresses entered as its "Local" addresses.

IKE. Direction/Type—this setting is used when determining if the IKE policy matches the current traffic. Select the desired option.

  • Responder only —incoming connections are allowed, but outgoing connections will be blocked.
  • Initiator and Responder — both incoming and outgoing connections are allowed.

Exchange Mode—ensure the remote VPN endpoint is set to use "Main Mode".

Diffie-Hellman (DH) Group—the Diffie-Hellman algorithm is used when exchanging keys. The DH Group setting determines the number of bit size used in the exchange. This value must match the value used on the remote VPN Gateway.

Local Identity Type—select the desired option to match the "Remote Identity Type" setting on the remote VPN endpoint.

  • WAN IP Address — your Internet IP address.
  • Fully Qualified Domain Name — your domain name.
  • Fully Qualified User Name — your name, E-mail address, or other ID.

Local Identity Data—enter the data for the selection above. (If WAN IP Address is selected, no input is required.)

Remote Identity Type—select the desired option to match the "Local Identity Type" setting on the remote VPN endpoint.

  • IP Address — the Internet IP address of the remote VPN endpoint.

Virtual Private Networking 7-41

Page 136 of the NETGEAR DG834G user manual — How to Set Up VPN Tunnels in Special Circumstances
Page 136 · click to enlarge
Page 136
  • Fully Qualified Domain Nam e — the Domain name of the remote VPN endpoint.
  • Fully Qualified User Name — the name, E-mail address, or other ID of the remote VPN endpoint.

Remote Identity Data—enter the data for the selection above. (If IP Address is selected, no input is required.)

Parameters. Encryption Algorithm—encryption Algorithm used for both IKE and IPSec. This setting must match the setting used on the remote VPN Gateway. DES and 3DES are supported.

  • DES—the Data Encryption Standard (DES) processes input data that is 64 bits wide, encrypting these values using a 56 bit key. Faster but less secure than 3DES.
  • 3DES—(Triple DES) achieves a higher level of security by encrypting the data three times using DES with three different, unrelated keys.

Authentication Algorithm—authentication Algorithm used for both IKE and IPSec. This setting must match the setting used on the remote VPN Gateway. Auto, MD5, and SHA-1 are supported. Auto negotiates with the remote VPN endpoint and is not available in responder-only mode.

  • MD5—128 bits, faster but less secure.
  • SHA-1 (default)—160 bits, slower but more secure.

Pre-shared Key—the key must be entered both here and on the remote VPN Gateway.

SA Life Time—this determines the time interval before the SA (Security Association) expires. (It will automatically be re-established as required.) While using a short time period (or data amount) increases security, it also degrades performance. It is common to use periods over an hour (3600 seconds) for the SA Life Time. This setting applies to both IKE and IPSec SAs.

IPSec PFS (Perfect Forward Secrecy)—if enabled, security is enhanced by ensuring that the key is changed at regular intervals. Also, even if one key is broken, subsequent keys are no easier to break. (Each key has no relationship to the previous key.)

This setting applies to both IKE and IPSec SAs. When configuring the remote endpoint to match this setting, you may have to specify the "Key Group" used. For this device, the "Key Group" is the same as the "DH Group" setting in the IKE section.

7-42 Virtual Private Networking

Page 137 of the NETGEAR DG834G user manual — How to Set Up VPN Tunnels in Special Circumstances
Page 137 · click to enlarge
Page 137
NETGEAR DG834G — How to Set Up VPN Tunnels in Special Circumstances diagram (page 137)
Fig. 71 · How to Set Up VPN Tunnels in Special Circumstances
1. Set the LAN IPs on each DG834G v3 to different subnets and configure each properly for the Internet. The following settings are assumed for this example:

Secure Association -- Main Mode or Manual Keys: Main

Diffie-Hellman (DH) Group -- Group 1 or Group 2: Group 2

VPN Endpoint Local IPSec ID LAN IP Address Subnet Mask

Virtual Private Networking 7-43

Page 138 of the NETGEAR DG834G user manual — How to Set Up VPN Tunnels in Special Circumstances
Page 138 · click to enlarge
Page 138
2. Open the DG834G v3 on LAN A management interface and click on VPN Policies .
NETGEAR DG834G — How to Set Up VPN Tunnels in Special Circumstances diagram (page 138)
Fig. 72 · How to Set Up VPN Tunnels in Special Circumstances
3. Click Add Auto Policy .
  • 4. Enter policy settings (see Figure 7-43 ).
  • General — Policy Name = GtoG — Remote VPN Endpoint Address Type = Fixed IP Address — Remote VPN Endpoint Address Data = 22.23.24.25
  • Local LAN – use default setting
  • Remote LAN — IP Address = select Subnet address from the pulldown menu. — Start IP address = 192.168.3.1 — Subnet Mask = 255.255.255.0
  • IKE — Direction = Initiator and Responder — Exchange Mode = Main Mode — Diffie-Hellman (DH) Group = Group 2 (1024 Bit) — Local Identity Type = use default setting — Remote Identity Type = use default setting
  • Parameters — Encryption Algorithm = 3DES

7-44 Virtual Private Networking

Page 139 of the NETGEAR DG834G user manual — How to Set Up VPN Tunnels in Special Circumstances
Page 139 · click to enlarge
Page 139

— Authentication Algorithm = MD5 — Pre-shared Key = 12345678

NETGEAR DG834G — How to Set Up VPN Tunnels in Special Circumstances diagram (page 139)
Fig. 73 · How to Set Up VPN Tunnels in Special Circumstances

Virtual Private Networking 7-45

Page 140 of the NETGEAR DG834G user manual — How to Set Up VPN Tunnels in Special Circumstances
Page 140 · click to enlarge
Page 140
5. Click Apply . The Get VPN Policies web page is displayed.
  • 6. Repeat for the DG834G v3 on LAN B and pay special attention to use the following network settings as appropriate.
  • General, Remote Address Data (e.g., 14.15.16.17 )
  • Remote LAN, Start IP Address — IP Address (e.g, 192.168.0.1 ) — Subnet Mask (e.g., 255.255.255.0 ) — Preshared Key (e.g., 12345678 )
7. Use the VPN Status screen to activate the VPN tunnel by performing the following steps:

“Activating a VPN Tunnel” on page 7-29 for information on the other ways.

7-46 Virtual Private Networking

Page 141 of the NETGEAR DG834G user manual — How to Set Up VPN Tunnels in Special Circumstances
Page 141 · click to enlarge
Page 141

a. Open the DG834G v3 management interface and click on VPN Status to display the VPN Status/Log screen (Figure 7-45).

b. Click VPN Status (Figure 7-45) to display the Current VPN Tunnels (SAs) screen (Figure 7-46). Click on Connect for the VPN tunnel you want to activate.

c. Review the VPN Status/Log screen (Figure 7-45) to verify that the tunnel is connected.

Virtual Private Networking 7-47

Page 142 of the NETGEAR DG834G user manual — Using Manual Policy to Configure VPN Tunnels
Page 142 · click to enlarge
Page 142

Using Manual Policy to Configure VPN Tunnels

As an alternative to IKE, you may use Manual Keying, in which you must specify each phase of the connection. A "Manual" VPN policy requires all settings for the VPN tunnel to be manually input at each end (both VPN endpoints).

Click the VPN Policies link of the main menu, and then click the Add Manual Policy radio button to display the Manual Keys menu shown in Figure 7-47.

NETGEAR DG834G — Using Manual Policy to Configure VPN Tunnels diagram (page 142)
Fig. 74 · Using Manual Policy to Configure VPN Tunnels

7-48 Virtual Private Networking

Page 143 of the NETGEAR DG834G user manual — Using Manual Policy to Configure VPN Tunnels
Page 143 · click to enlarge
Page 143

General. The DG834G v3 VPN tunnel network connection fields are defined as follows:

  • Policy Name —enter a unique name to identify this policy. This name is not supplied to the remote VPN endpoint. It is used only to help you manage the policies.
  • Remote VPN Endpoint —select the desired option (IP address or Fully Qualified Domain Name) and enter the address of the remote VPN endpoint to which you wish to connect.

its "Remote VPN Endpoint".

Local LAN. This identifies which PCs on your LAN are covered by this policy. For each selection, data must be provided as follows:

  • Single address —enter an IP address in the "Single/Start IP address" field. Typically, this setting is used when you wish to make a single Server on your LAN available to remote users.
  • Range address —enter the starting IP address in the "Single/Start IP address" field, and the finish IP address in the "Finish IP address" field. This must be an address range used on your LAN.
  • Subnet address —enter an IP address in the "Single/Start IP address" field, and the desired network mask in the "Subnet Mask" field.

The remote VPN endpoint must have these IP addresses entered as its "Remote" addresses.

Remote LAN. This identifies which PCs on the remote LAN are covered by this policy. For each selection, data must be provided as follows:

  • Single PC - no Subnet —select this option if there is no LAN (only a single PC) at the remote endpoint. If this option is selected, no additional data is required.
  • Single address —enter an IP address in the "Single/Start IP address" field. This must be an address on the remote LAN. Typically, this setting is used when you wish to access a server on the remote LAN.
  • Range address —enter the starting IP address in the "Single/Start IP address" field, and the finish IP address in the "Finish IP address" field. This must be an address range used on the remote LAN.
  • Subnet address —enter an IP address in the "Single/Start IP address" field, and the desired network mask in the "Subnet Mask" field.

The remote VPN endpoint must have these IP addresses entered as its "Local" addresses.

Virtual Private Networking 7-49

Page 144 of the NETGEAR DG834G user manual — Using Manual Policy to Configure VPN Tunnels
Page 144 · click to enlarge
Page 144

ESP Configuration. ESP (Encapsulating Security Payload) provides security for the payload (data) sent through the VPN tunnel.

SPI—enter the required security policy indexes (SPIs). Each policy must have unique SPIs. These settings must match the remote VPN endpoint. The "in" setting here must match the "out" setting on the remote VPN endpoint, and the "out" setting here must match the "in" setting on the remote VPN endpoint.

Encryption—select the desired Encryption Algorithm, and enter the key in the field provided. For 3DES, the keys should be 24 ASCII characters and for DES, the keys should be 8 ASCII characters.

  • DES—the Data Encryption Standard (DES) processes input data that is 64 bits wide, encrypting these values using a 56 bit key. Faster but less secure than 3DES.
  • 3DES—(Triple DES) achieves a higher level of security by encrypting the data three times using DES with three different, unrelated keys.

Authentication—select the desired SHA-1 or MD5 Authentication Algorithm, and enter the key in the field provided. For MD5, the keys should be 16 ASCII characters. For SHA-1, the keys should be 20 ASCII characters.

  • MD5—128 bits, faster but less secure.
  • SHA-1 (default)—160 bits, slower but more secure.

7-50 Virtual Private Networking

Page 145 of the NETGEAR DG834G user manual — Basic Functioning
Page 145 · click to enlarge
Page 145

Chapter 8 Troubleshooting

This chapter gives information about troubleshooting your 54 Mbps ADSL Modem Wireless Router Model DG834G. After each problem description, instructions are provided to help you diagnose and solve the problem. For the common problems listed, go to the section indicated.

  • Is the router on?
  • Have I connected the router correctly?

Go to “Basic Functioning” on page 8-1.

  • I can’t access the router’s configuration with my browser.

Go to “Troubleshooting the Web Configuration Interface” on page 8-3.

  • I’ve configured the router but I can’t access the Internet.

Go to “Troubleshooting the ISP Connection” on page 8-4.

  • I can’t remember the router’s configuration password.

Go to “Restoring the Default Configuration and Password” on page 8-9.

  • I want to clear the configuration and start over again.

Go to “Restoring the Default Configuration and Password” on page 8-9.

Basic Functioning

After you turn on power to the router, the following sequence of events should occur:

1. When power is first applied, verify that the Power LED is on (see “The Router’s Front Panel” on page 2-8 for an illustration and explanation of the LEDs).
2. Verify that the Test LED lights within a few seconds, indicating that the self-test procedure is running.
3. After approximately 10 seconds, verify that:

a. The Test LED is not lit.

b. The LAN port LEDs are lit for any local ports that are connected.

Troubleshooting 8-1

Page 146 of the NETGEAR DG834G user manual — LAN or Internet Port LEDs Not On
Page 146 · click to enlarge
Page 146

c. The WAN port LED is lit.

If a port’s LED is lit, a link has been established to the connected device. If a LAN port is connected to a 100 Mbps device, verify that the port’s LED is green. If the port is 10 Mbps, the LED will be amber.

If any of these conditions does not occur, refer to the appropriate following section.

Power LED Not On

If the Power and other LEDs are off when your router is turned on:

  • Make sure that the power cord is properly connected to your router and that the power supply adapter is properly connected to a functioning power outlet.
  • Check that you are using the 12 V DC power adapter supplied by NETGEAR for this product.

If the error persists, you have a hardware problem and should contact technical support.

Test LED Never Turns On or Test LED Stays On

When the router is turned on, the Test LED turns on for about 10 seconds and then turns off. If the Test LED does not turn on, or if it stays on, there is a fault within the router.

If you experience problems with the Test LED:

  • Cycle the power to see if the router recovers and the LED blinks for the correct amount of time.

If all LEDs including the Test LED are still on one minute after power up:

  • Cycle the power to see if the router recovers.
  • Clear the router’s configuration to factory defaults. This will set the router’s IP address to 192.168.0.1. This procedure is explained in “Using the Reset button” on page 8-9 .

If the error persists, you might have a hardware problem and should contact technical support.

LAN or Internet Port LEDs Not On

If either the LAN LEDs or Internet LED do not light when the Ethernet connection is made, check the following:

8-2 Troubleshooting

Page 147 of the NETGEAR DG834G user manual — Troubleshooting the Web Configuration Interface
Page 147 · click to enlarge
Page 147
  • Make sure that the Ethernet cable connections are secure at the router and at the hub or workstation.
  • Make sure that power is turned on to the connected hub or workstation.
  • Be sure you are using the correct cable:

— When connecting the router’s WAN ADSL port, use the cable that was supplied with the

DG834G v3.

Troubleshooting the Web Configuration Interface

If you are unable to access the router’s Web Configuration interface from a computer on your local network, check the following:

  • If you are using an Ethernet-connected computer, check the Ethernet connection between the computer and the router as described in the previous section.
  • Make sure your computer’s IP address is on the same subnet as the router. If you are using the recommended addressing scheme, your computer’s address should be in the range of 192.168.0.2 to 192.168.0.254. Refer to “Preparing a Computer for Network Access” in Appendix C to find your computer’s IP address.

Recent versions of Windows and MacOS will generate and assign an IP address if the computer cannot reach a DHCP server. These auto-generated addresses are in the range of 169.254.x.x. If your IP address is in this range, check the connection from the computer to the router and reboot your computer.

  • If your router’s IP address was changed and you do not know the current IP address, clear the router’s configuration to factory defaults. This will set the router’s IP address to 192.168.0.1. This procedure is explained in “Using the Reset button” on page 8-9 .
  • Make sure your browser has Java, JavaScript, or ActiveX enabled. If you are using Internet Explorer, click Refresh to be sure the Java applet is loaded.
  • Try quitting the browser and launching it again.
  • Make sure you are using the correct login information. The factory default login name is admin and the password is password . Make sure that CAPS LOCK is off when entering this information.

Troubleshooting 8-3

Page 148 of the NETGEAR DG834G user manual — ADSL link
Page 148 · click to enlarge
Page 148

If the router does not save changes you have made in the Web Configuration Interface, check the following:

  • When entering configuration settings, be sure to click the Apply button before moving to another menu or tab, or your changes are lost.
  • Click the Refresh or Reload button in the Web browser. The changes may have occurred, but the Web browser may be caching the old configuration.

Troubleshooting the ISP Connection

If your router is unable to access the Internet, you should check the ADSL connection, then the WAN TCP/IP connection.

ADSL link

If your router is unable to access the Internet, you should first determine whether you have an ADSL link with the service provider. The state of this connection is indicated with the Internet LED.

Internet LED Green or Blinking Green

If your Internet LED is green or blinking green, then you have a good ADSL connection. You can be confident that the service provider has connected your line correctly and that your wiring is correct.

Internet LED Blinking Amber

If your Internet LED is blinking amber, then your modem router is attempting to make an ADSL connection with the service provider. The LED should turn green within several minutes.

If the Internet LED does not turn green, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.

If disconnecting telephones does not result in a green Internet LED, there may be a problem with your wiring. If the telephone company has tested the ADSL signal at your Network Interface Device (NID), then you may have poor quality wiring in your house.

8-4 Troubleshooting

Page 149 of the NETGEAR DG834G user manual — Obtaining a WAN IP Address
Page 149 · click to enlarge
Page 149

If the Internet LED is off, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.

If disconnecting telephones does not result in a green Internet LED the problem may be one of the following:

  • Check that the telephone company has made the connection to your line and tested it.
  • Verify that you are connected to the correct telephone line. If you have more than one phone line, be sure that you are connected to the line with the ADSL service. It may be necessary to use a swapper if you ADSL signal is on pins 1 and 4 or the RJ-11 jack. The ADSL Modem Wireless Router uses pins 2 and 3.

Obtaining a WAN IP Address

If your modem router is unable to access the internet, and your Internet LED is green or blinking green, you should determine whether the modem router is able to obtain a WAN IP address from the ISP. Unless you have been assigned a static IP address, your modem router must request an IP address from the ISP. You can determine whether the request was successful using the browser interface.

To check the WAN IP address from the browser interface:

1. Launch your browser and select an external site such as www.netgear.com
2. Access the Main Menu of the modem router’s configuration at http://192.168.0.1
3. Under the Maintenance heading check that an IP address is shown for the WAN Port. If 0.0.0.0 is shown, your modem router has not obtained an IP address from your ISP.

If your router is unable to obtain an IP address from the ISP, the problem may be one of the following:

  • Your ISP may require a Multiplexing Method or Virtual Path Identifier/Virtual Channel Identifier parameter. Verify with your ISP the Multiplexing Method and parameter value, and update the router’s ADSL Settings accordingly.
  • Your ISP may require a login program. Ask your ISP whether they require PPP over Ethernet (PPPoE) or PPP over ATM (PPPOA) login.

Internet LED Off · Troubleshooting 8-5

Page 150 of the NETGEAR DG834G user manual — Troubleshooting PPPoE or PPPoA
Page 150 · click to enlarge
Page 150
  • If you have selected a login program, you may have incorrectly set the Service Name, User Name and Password. See “Troubleshooting PPPoE or PPPoA” , below.
  • Your ISP may check for your computer's host name. Assign the computer Host Name of your ISP account to the modem router in the browserbased Setup Wizard.
  • Your ISP only allows one Ethernet MAC address to connect to Internet, and may check for your computer’s MAC address. In this case:

Inform your ISP that you have bought a new network device, and ask them to use the router’s MAC address.

OR

Configure your router to spoof your computer’s MAC address. This can be done in the Basic Settings menu. Refer to the ADSL Modem Wirelesss Router Setup Manual (see Table 2-2 on page 2-10).

Troubleshooting PPPoE or PPPoA

The PPPoA or PPPoA connection can be debugged as follows:

1. Access the Main Menu of the router at http://192.168.0.1
2. Under the Maintenance heading, select the Router Status link.
3. Click the Connection Statu s button.
4. If all of the steps indicate “OK” then your PPPoE or PPPoA connection is up and working.
5. If any of the steps indicates “Failed”, you can attempt to reconnect by clicking Connect . The modem router will continue to attempt to connect indefinitely.

If you cannot connect after several minutes, you may be using an incorrect Service Name, User Name or Password. There also may be a provisioning problem with your ISP.

PPPoE or PPPoA until data is transmitted to the network.

8-6 Troubleshooting

Page 151 of the NETGEAR DG834G user manual — Testing the LAN Path to Your Router
Page 151 · click to enlarge
Page 151

Troubleshooting Internet Browsing

If your modem router can obtain an IP address but your computer is unable to load any Web pages from the Internet:

  • Your computer may not recognize any DNS server addresses.

A DNS server is a host on the Internet that translates Internet names (such as www addresses) to numeric IP addresses. Typically your ISP will provide the addresses of one or two DNS servers for your use. If you entered a DNS address during the modem router’s configuration, reboot your computer and verify the DNS address as described in “Preparing a Computer for Network Access” in Appendix C. Alternatively, you can configure your computer manually with DNS addresses, as explained in your operating system documentation.

  • Your computer may not have the modem router configured as its TCP/IP modem router.

If your computer obtains its information from the modem router by DHCP, reboot the computer and verify the modem router address as described in “Preparing a Computer for Network Access” in Appendix C.

Troubleshooting a TCP/IP Network Using the Ping Utility

Most TCP/IP terminal devices and routers contain a ping utility that sends an echo request packet to the designated device. The device then responds with an echo reply. Troubleshooting a TCP/IP network is made very easy by using the ping utility in your computer.

Testing the LAN Path to Your Router

You can ping the router from your computer to verify that the LAN path to your router is set up correctly.

To ping the router from a PC running Windows 95 or later:

1. From the Windows toolbar, click the Start button and select Run .
2. In the field provided, type Ping followed by the IP address of the router, as in this example:

ping 192.168.0.1

3. Click OK .

You should see a message like this one:

Pinging <IP address> with 32 bytes of data

Troubleshooting 8-7

Page 152 of the NETGEAR DG834G user manual — Testing the Path from Your Computer to a Remote Device
Page 152 · click to enlarge
Page 152

If the path is working, you see this message:

Reply from < IP address >: bytes=32 time=NN ms TTL=xxx

If the path is not working, you see this message:

If the path is not functioning correctly, you could have one of the following problems:

  • Wrong physical connections

— Make sure the LAN port LED is on. If the LED is off, follow the instructions in “LAN

or Internet Port LEDs Not On” on page 8-2.

— Check that the corresponding Link LEDs are on for your network interface card and

for the hub ports (if any) that are connected to your workstation and router.

  • Wrong network configuration

— Verify that the Ethernet card driver software and TCP/IP software are both installed

and configured on your PC or workstation.

— Verify that the IP address for your router and your workstation are correct and that the

addresses are on the same subnet.

Testing the Path from Your Computer to a Remote Device

After verifying that the LAN path works correctly, test the path from your PC to a remote device. From the Windows run menu, type:

PING -n 10

where is the IP address of a remote device such as your ISP’s DNS server.

If the path is functioning correctly, replies as in the previous section are displayed. If you do not receive replies:

— Check that your PC has the IP address of your router listed as the default modem router. If

the IP configuration of your PC is assigned by DHCP, this information will not be visible in your PC’s Network Control Panel. Verify that the IP address of the router is listed as the default modem router as described in “Preparing a Computer for Network Access” in Appendix C.

— Check to see that the network address of your PC (the portion of the IP address specified

by the netmask) is different from the network address of the remote device.

— Check that your cable or DSL modem is connected and functioning.

Request timed out · 8-8 Troubleshooting

Page 153 of the NETGEAR DG834G user manual — Problems with Date and Time
Page 153 · click to enlarge
Page 153

— If your ISP assigned a host name to your PC, enter that host name as the Account Name in

the Basic Settings menu.

— Your ISP could be rejecting the Ethernet MAC addresses of all but one of your PCs. Many

broadband ISPs restrict access by only allowing traffic from the MAC address of your broadband modem, but some ISPs additionally restrict access to the MAC address of a single PC connected to that modem. If this is the case, you must configure your router to “clone” or “spoof” the MAC address from the authorized PC. Refer to your ADSL Modem Wirelesss Router Setup Manual (see Table 2-2 on page 2-10).

Restoring the Default Configuration and Password

This section explains how to restore the factory default configuration settings, changing the router’s administration password to password and the IP address to 192.168.0.1. You can erase the current configuration and restore factory defaults in two ways:

  • Use the Erase function of the Web Configuration Manager (see “Backing Up, Restoring, or Erasing Your Settings” on page 5-1 ).
  • Use the Default Reset button on the rear panel of the router. Use this method for cases when the administration password or IP address is not known.

Using the Reset button

To restore the factory default configuration settings without knowing the administration password or IP address, you must use the Default Reset button on the rear panel of the router.

1. Press and hold the Default Reset button until the Test LED turns on (about 10 seconds).
2. Release the Default Reset button and wait for the router to reboot.

Problems with Date and Time

The E-mail menu in the Content Filtering section displays the current date and time of day. The ADSL Modem Wireless Router uses the Network Time Protocol (NTP) to obtain the current time from one of several Network Time Servers on the Internet. Each entry in the log is stamped with the date and time of day. Problems with the date and time function can include:

Troubleshooting 8-9

Page 154 of the NETGEAR DG834G user manual — Restoring the Default Configuration and Password
Page 154 · click to enlarge
Page 154
  • Date shown is January 1, 2000 Cause: The router has not yet successfully reached a Network Time Server. Check that your Internet access settings are configured correctly. If you have just completed configuring the router, wait at least five minutes and check the date and time again.
  • Time is off by one hour Cause: The router does not automatically sense Daylight Savings Time. In the E-mail menu, check or uncheck the box marked “Adjust for Daylight Savings Time”.

8-10 Troubleshooting

Page 155 of the NETGEAR DG834G user manual — Appendix A Technical Specifications
Page 155 · click to enlarge
Page 155

Appendix A Technical Specifications

This appendix provides technical specifications for the 54 Mbps ADSL Modem Wireless Router Model DG834G.

Network Protocol and Standards Compatibility

Data and Routing Protocols: TCP/IP, RIP-1, RIP-2, DHCP, PPPoE or PPPoA, RFC 1483 Bridged or Routed Ethernet, and RFC 1577 Classical IP over ATM

North America120V, 60 Hz, input
United Kingdom, Australia240V, 50 Hz, input
Europe230V, 50 Hz, input
Japan100V, 50/60 Hz, input
All regions (output)12 V AC @ 1.0A output
Dimensions6.9" x 4.7" x 1.1" 175 mm x 119 mm x 28 mm
Weight0.7 lbs. 0.3 kg
Operating temperature0 ° to 40 ° C (32º to 104º F)
Operating humidity90% maximum relative humidity, noncondensing

Meets requirements of: FCC Part 15 Class B; VCCI Class B; EN 55 022 (CISPR 22), Class B

LAN10BASE-T or 100BASE-Tx, RJ-45

WAN: ADSL, ADSL2+, Dual RJ-11, pins 2 and 3,T1.413, G.DMT, G.Lite, ITU Annex A (for the DG834G) or ITU Annex B (for the DG834GB)

Show 6 more labels / short text on this page
Power Adapter · Physical Specifications · Environmental Specifications · Electromagnetic Emissions · Interface Specifications · Technical Specifications A-1
Page 156 of the NETGEAR DG834G user manual — Appendix A Technical Specifications
Page 156 · click to enlarge
Page 156

A-2 Technical Specifications

Page 157 of the NETGEAR DG834G user manual — Configuration Profile
Page 157 · click to enlarge
Page 157

Appendix B NETGEAR VPN Configuration

DG834G v3 to FVL328

This appendix is a case study on how to configure a secure IPSec VPN tunnel from a NETGEAR DG834G v3 to a FVL328. This case study follows the VPN Consortium interoperability profile guidelines (found at http://www.vpnc.org/InteropProfiles/Interop-01.html).

Configuration Profile

The configuration in this document follows the addressing and configuration mechanics defined by the VPN Consortium. Gather all the necessary information before you begin the configuration process. Verify whether the firmware is up to date, all of the addresses that will be necessary, and all of the parameters that need to be set on both sides. Check that there are no firewall restrictions.

Table B-1. Profile Summary

VPN Consortium ScenarioScenario 1

Type of VPN LAN-to-LAN or Gateway-to-Gateway (not PC/Client-to-Gateway)

Security SchemeIKE with Preshared Secret/Key (not Certificate-based)

IP Addressing:

NETGEAR-Gateway A Static IP address

NETGEAR-Gateway B Static IP address

NETGEAR VPN Configuration B-1

Page 158 of the NETGEAR DG834G user manual — Step-By-Step Configuration
Page 158 · click to enlarge
Page 158
NETGEAR DG834G — Step-By-Step Configuration diagram (page 158)
Fig. 75 · Step-By-Step Configuration

172.23.9.1 10.5.6.1 WAN IP WAN IP LAN IP LAN IP

Step-By-Step Configuration

1. Configure the DG834G v3 as in the Gateway-to-Gateway procedures using the VPN Wizard (see “How to Set Up a Gateway-to-Gateway VPN Configuration” on page 7-21 ), being certain to use appropriate network addresses for the environment.

The LAN Addresses used in this example are as follows:

NETGEAR DG834G — Step-By-Step Configuration diagram (page 158)
Fig. 76 · Step-By-Step Configuration

a. In Step 1, enter toFVL328 for the Connection Name.

b. In Step 2, enter 22.23.24.25 for the remote WAN's IP address.

  • c. In Step 3, enter the following:
  • IP Address = 172.23.9.1
  • Subnet Mask = 255.255.255.0

B-2 NETGEAR VPN Configuration

Page 159 of the NETGEAR DG834G user manual — Step-By-Step Configuration
Page 159 · click to enlarge
Page 159
NETGEAR DG834G — Step-By-Step Configuration diagram (page 159)
Fig. 77 · Step-By-Step Configuration

Click VPN Policies under Advanced - VPN to invoke this screen

toFVL328 10.5.6.1 172.23.9.1

NETGEAR DG834G — Step-By-Step Configuration diagram (page 159)
Fig. 78 · Step-By-Step Configuration

22.23.24.25

10 10 5 6

NETGEAR VPN Configuration B-3

toFVL328 · 172 23 9 · Figure B-2

Page 160 of the NETGEAR DG834G user manual — Step-By-Step Configuration
Page 160 · click to enlarge
Page 160
2. Configure the FVL328 as in the Gateway-to-Gateway procedures for the VPN Wizard (see “How to Set Up a Gateway-to-Gateway VPN Configuration” on page 7-21 ), being certain to use appropriate network addresses for the environment.

a. In Step 1, enter toDG834 for the Connection Name

b. In Step 2, enter 14.15.16.17 for the remote WAN's IP address

  • c. In Step 3, enter the following:
  • IP Address = 10.5.6.1
  • Subnet Mask = 255.255.255.0

B-4 NETGEAR VPN Configuration

Page 161 of the NETGEAR DG834G user manual — Step-By-Step Configuration
Page 161 · click to enlarge
Page 161
NETGEAR DG834G — Step-By-Step Configuration diagram (page 161)
Fig. 79 · Step-By-Step Configuration

Click IKE Policies under VPN to invoke this screen

Click VPN Policies under VPN to invoke this screen

NETGEAR VPN Configuration B-5

Figure B-3

Page 162 of the NETGEAR DG834G user manual — Configuration Profile
Page 162 · click to enlarge
Page 162
3. Test the VPN tunnel by pinging the remote network from a PC attached to the DG834G v3.

a. Open the command prompt (Start -> Run -> cmd)

b. ping 172.23.9.1

NETGEAR DG834G — DG834G v3 with FQDN to FVL328 diagram (page 162)
Fig. 80 · DG834G v3 with FQDN to FVL328

time.

DG834G v3 with FQDN to FVL328

This appendix is a case study on how to configure a VPN tunnel from a NETGEAR DG834G v3 to a FVL328 using a Fully Qualified Domain Name (FQDN) to resolve the public address of one or both routers. This case study follows the VPN Consortium interoperability profile guidelines (found at http://www.vpnc.org/InteropProfiles/Interop-01.html).

Configuration Profile

The configuration in this document follows the addressing and configuration mechanics defined by the VPN Consortium. Gather all the necessary information before you begin the configuration process. Verify whether the firmware is up to date, all of the addresses that will be necessary, and all of the parameters that need to be set on both sides. Check that there are no firewall restrictions.

B-6 NETGEAR VPN Configuration

Figure B-4

Page 163 of the NETGEAR DG834G user manual — DG834G v3 with FQDN to FVL328
Page 163 · click to enlarge
Page 163

Table B-2. Profile Summary

NETGEAR DG834G — DG834G v3 with FQDN to FVL328 diagram (page 163)
Fig. 81 · DG834G v3 with FQDN to FVL328

NETGEAR VPN Configuration B-7

Page 164 of the NETGEAR DG834G user manual — Step-By-Step Configuration
Page 164 · click to enlarge
Page 164

The Use of a Fully Qualified Domain Name (FQDN)

Many ISPs (Internet Service Providers) provide connectivity to their customers using dynamic instead of static IP addressing. This means that a user’s IP address does not remain constant over time which presents a challenge for gateways attempting to establish VPN connectivity.

A Dynamic DNS (DDNS) service allows a user whose public IP address is dynamically assigned to be located by a host or domain name. It provides a central public database where information (such as email addresses, host names and IP addresses) can be stored and retrieved. Now, a gateway can be configured to use a 3rd party service in lieu of a permanent and unchanging IP address to establish bi-directional VPN connectivity.

To use DDNS, you must register with a DDNS service provider. Example DDNS Service Providers include:

  • DynDNS: <a href="http://www.dyndns.org" rel="nofollow noopener" target="_blank">www.dyndns.org</a>
  • <a href="http://TZO.com" rel="nofollow noopener" target="_blank">TZO.com</a>: netgear.<a href="http://tzo.com" rel="nofollow noopener" target="_blank">tzo.com</a>
  • ngDDNS: ngddns.<a href="http://iego.net" rel="nofollow noopener" target="_blank">iego.net</a>

In this example, Gateway A is configured using an example FQDN provided by a DDNS Service provider. In this case we established the hostname dg834g.dyndns.org for gateway A using the DynDNS service. Gateway B will use the DDNS Service Provider when establishing a VPN tunnel.

In order to establish VPN connectivity Gateway A must be configured to use Dynamic DNS, and Gateway B must be configured to use a DNS hostname to find Gateway A provided by a DDNS Service Provider. Again, the following step-by-step procedures assume that you have already registered with a DDNS Service Provider and have the configuration information necessary to set up the gateways.

Step-By-Step Configuration

1. Log in to the DG834G v3 labeled Gateway A as in the illustration.

Out of the box, the DG834G v3 is set for its default LAN address of http://192.168.0.1 with its default user name of admin and default password of password. For this example we will assume you have set the local LAN address as 10.5.6.1 for Gateway A and have set your own password.

2. Click on the Dynamic DNS link on the left side of the Settings management GUI. This will take you to the Dynamic DNS Menu.

B-8 NETGEAR VPN Configuration

Page 165 of the NETGEAR DG834G user manual — Step-By-Step Configuration
Page 165 · click to enlarge
Page 165
3. On the DG834G v3, configure the Dynamic DNS settings.

a. Browse to the Dynamic DNS Setup Screen (see Figure B-6) in the Advanced menu.

NETGEAR DG834G — Step-By-Step Configuration diagram (page 165)
Fig. 82 · Step-By-Step Configuration
  • b. Configure this screen with appropriate account and hostname settings and then click Apply .
  • Check the box Use a Dynamic DNS Service .
  • Host Name = dg834g.<a href="http://dyndns.org" rel="nofollow noopener" target="_blank">dyndns.org</a>
  • User Name = <user's account username>
  • Password = <user's account password>

c. Click Show Status. The resulting screen should show Update OK: good (see Figure B-7).

NETGEAR DG834G — Step-By-Step Configuration diagram (page 165)
Fig. 83 · Step-By-Step Configuration

NETGEAR VPN Configuration B-9

Figure B-6 · Figure B-7

Page 166 of the NETGEAR DG834G user manual — Step-By-Step Configuration
Page 166 · click to enlarge
Page 166
4. On the FVL328, configure the Dynamic DNS settings. Assume a properly configured DynDNS account.

a. Browse to the Dynamic DNS Setup Screen (see Figure B-8) in the Advanced menu.

NETGEAR DG834G — Step-By-Step Configuration diagram (page 166)
Fig. 84 · Step-By-Step Configuration
  • b. Select the <a href="http://DynDNS.org" rel="nofollow noopener" target="_blank">DynDNS.org</a> radio button (see Figure B-8 ), configure with appropriate account and hostname settings (see Figure B-9 ), and then click Apply .
  • Host and Domain Name = fvl328.<a href="http://dyndns.org" rel="nofollow noopener" target="_blank">dyndns.org</a>
  • User Name = <user's account username>
  • Password = <user's account password>

B-10 NETGEAR VPN Configuration

Figure B-8

Page 167 of the NETGEAR DG834G user manual — Step-By-Step Configuration
Page 167 · click to enlarge
Page 167
NETGEAR DG834G — Step-By-Step Configuration diagram (page 167)
Fig. 85 · Step-By-Step Configuration

c. Click Show Status. The resulting screen should show Update OK: good (see Figure B-10).

NETGEAR DG834G — Step-By-Step Configuration diagram (page 167)
Fig. 86 · Step-By-Step Configuration

NETGEAR VPN Configuration B-11

Figure B-9 · Figure B-10

Page 168 of the NETGEAR DG834G user manual — FVL328 172.23.6.1 255.255.255.0
Page 168 · click to enlarge
Page 168
5. Configure the DG834G v3 as in the Gateway-to-Gateway procedures using the VPN Wizard (see “How to Set Up a Gateway-to-Gateway VPN Configuration” on page 7-21 ), being certain to use appropriate network addresses for the environment.

The LAN Addresses used in this example are as follows:

Device LAN IP Address LAN Subnet Mask

DG834G v3 10.5.6.1 255.255.255.0

FVL328 172.23.6.1 255.255.255.0

a. In Step 1, enter toFVL328 for the Connection Name.

b. In Step 2, enter fvl328.dyndns.org for the remote WAN's IP address.

  • c. In Step 3, enter the following:
  • IP Address = 172.23.9.1
  • Subnet Mask = 255.255.255.0
6. Configure the FVL328 as in the Gateway-to-Gateway procedures for the VPN Wizard (see “How to Set Up a Gateway-to-Gateway VPN Configuration” on page 7-21 ), being certain to use appropriate network addresses for the environment.

a. In Step 1, enter toDG834 for the Connection Name.

b. In Step 2, enter dg834g.dyndns.org for the remote WAN's IP address.

  • c. In Step 3, enter the following:
  • IP Address = 10.5.6.1
  • Subnet Mask = 255.255.255.0
7. Test the VPN tunnel by pinging the remote network from a PC attached to the DG834G v3.

a. Open the command prompt (Start -> Run -> cmd)

b. ping 172.23.9.1

B-12 NETGEAR VPN Configuration

Page 169 of the NETGEAR DG834G user manual — Step-By-Step Configuration
Page 169 · click to enlarge
Page 169

time.

NETGEAR VPN Configuration B-13

Figure B-11

Page 170 of the NETGEAR DG834G user manual — Configuration Summary (Telecommuter Example)
Page 170 · click to enlarge
Page 170

Configuration Summary (Telecommuter Example)

The configuration in this document follows the addressing and configuration mechanics defined by the VPN Consortium. Gather all the necessary information before you begin the configuration process. Verify whether the firmware is up to date, all of the addresses that will be necessary, and all of the parameters that need to be set on both sides. Assure that there are no firewall restrictions.

Table B-3. Configuration summary (telecommuter example)

NETGEAR DG834G — Configuration Summary (Telecommuter Example) diagram (page 170)
Fig. 87 · Configuration Summary (Telecommuter Example)
Type of VPNPC/client-to-gateway, with client behind NAT router

Setting up a VPN between a remote PC running the NETGEAR ProSafe VPN Client and a network gateway involves the following two steps:

  • Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Office .

B-14 NETGEAR VPN Configuration

Page 171 of the NETGEAR DG834G user manual — Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Office
Page 171 · click to enlarge
Page 171
  • Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office configures the NETGEAR ProSafe VPN Client endpoint.
1. Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Office

Follow this procedure to configure a client-to-gateway VPN tunnel by filling out the VPN Auto Policy screen.

1. Log in to the VPN router at its LAN address of http://192.168.0.1 with its default user name of admin and password of password . Click the VPN Policies link in the main menu to display the VPN Policies screen. Click Add Auto Policy to proceed and enter the information.

NETGEAR VPN Configuration B-15

Page 172 of the NETGEAR DG834G user manual — Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Office
Page 172 · click to enlarge
Page 172
NETGEAR DG834G — Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Office diagram (page 172)
Fig. 88 · Step 1: Configuring the Client-to-Gateway VPN Tunnel…

fromDG834G (in the example) Dynamic IP address

IKE Keep Alive is optional; must match Remote LAN IP Address when enabled

(remote PC must respond to pings)

192.168.0.1 (in this example) 255.255.255.0

192.168.2.3 (in this example)

(Remote NAT router must have Address Reservation set and VPN Passthrough enabled)

Fully Qualified Domain Name fromDG834G.com (in this example)

Fully Qualified Domain Name toDG834G.com (in this example)

3DES 12345678 (in this example) 3600

B-16 NETGEAR VPN Configuration

Show 4 more labels / short text on this page
Subnet address · Single address · Main Mode · Figure B-13
Page 173 of the NETGEAR DG834G user manual — Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Office
Page 173 · click to enlarge
Page 173
2. Click Apply when done to get the VPN Policies screen.
NETGEAR DG834G — Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Office diagram (page 173)
Fig. 89 · Step 1: Configuring the Client-to-Gateway VPN Tunnel…

To view or modify the tunnel settings, select the radio button next to the tunnel entry and click Edit.

NETGEAR VPN Configuration B-17

Figure B-14

Page 174 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office
Page 174 · click to enlarge
Page 174
2. Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office

This procedure describes how to configure the 54 Mbps ADSL Modem Wireless Router Model DG834G. We will assume the PC running the client has a dynamically assigned IP address.

The PC must have a VPN client program installed that supports IPSec (in this case study, the NETGEAR VPN ProSafe Client is used). Go to the NETGEAR website (http://www.netgear.com) and select VPN01L_VPN05L in the Product Quick Find drop-down menu for information on how to purchase the NETGEAR ProSafe VPN Client.

software, be sure to turn off any virus protection or firewall software you may be running on your PC.

1. Install the NETGEA ProSafe VPN Client on the remote PC and reboot.

a. You may need to insert your Windows CD to complete the installation.

b. If you do not have a modem or dial-up adapter installed in your PC, you may see the warning message stating “The NETGEAR ProSafe VPN Component requires at least one dial-up adapter be installed.” You can disregard this message.

c. Install the IPSec Component. You may have the option to install either the VPN Adapter or the IPSec Component or both. The VPN Adapter is not necessary.

d. The system should show the ProSafe icon ( ) in the system tray after rebooting.

e. Double-click the system tray icon to open the Security Policy Editor.

2. Add a new connection.

a. Run the NETGEAR ProSafe Security Policy Editor program and create a VPN Connection.

B-18 NETGEAR VPN Configuration

Page 175 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office
Page 175 · click to enlarge
Page 175

b. From the Edit menu of the Security Policy Editor, click Add, then Connection. A New Connection listing appears in the list of policies. Rename the New Connection so that it matches the Connection Name you entered in the VPN Settings of the DG834G v3 on Gateway A.

tunnel is toDG834G and it does not have to match the VPN_client Connection Name used on the gateway side of the VPN tunnel (see Figure B-16) because Connection Names are arbitrary to how the VPN tunnel functions.

administrating the VPN.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office diagram (page 175)
Fig. 90 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

NETGEAR VPN Configuration B-19

Figure B-15

Page 176 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office
Page 176 · click to enlarge
Page 176
NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office diagram (page 176)
Fig. 91 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

c. Select Secure in the Connection Security check-box group.

d. Select IP Subnet in the ID Type menu.

e. In this example, type 192.168.0.1 in the Subnet field as the network address of the DG834G v3.

f. Enter 255.255.255.0 in the Mask field as the LAN Subnet Mask of the DG834G v3.

g. Select All in the Protocol menu to allow all traffic through the VPN tunnel.

h. Select the Connect using Secure Gateway Tunnel check box.

i. Select Domain Name in the ID Type menu below the check box and enter fromDG834G.com (in this example).

j. Select Gateway Hostname and enter ntgr.dyndns.org (in this example).

k. The resulting Connection Settings are shown in Figure B-16.

3. Configure the Security Policy in the 54 Mbps ADSL Modem Wireless Router Model DG834G software.

a. In the Network Security Policy list, expand the new connection by double clicking its name or clicking on the “+” symbol. My Identity and Security Policy subheadings appear below the connection name.

B-20 NETGEAR VPN Configuration

Figure B-16

Page 177 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office
Page 177 · click to enlarge
Page 177

b. Click on the Security Policy subheading to show the Security Policy menu.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office diagram (page 177)
Fig. 92 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

c. Select the Main Mode in the Select Phase 1 Negotiation Mode check box.

4. Configure the VPN Client Identity .

In this step, you will provide information about the remote VPN client PC. You will need to provide the Pre-Shared Key that you configured in the DG834G v3 and either a fixed IP address or a “fixed virtual” IP address of the VPN client PC.

NETGEAR VPN Configuration B-21

Figure B-17

Page 178 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office
Page 178 · click to enlarge
Page 178

a. In the Network Security Policy list on the left side of the Security Policy Editor window, click My Identity.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office diagram (page 178)
Fig. 93 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

b. Choose None in the Select Certificate menu.

c. Select Domain Name in the ID Type menu and enter toDG834G.com (in this example) in the box below it. Choose Disabled in the Virtual Adapter menu.

d. In the Internet Interface box, select Intel PRO/100VE Network Connection (in this example, your Ethernet adapter may be different) in the Name menu and enter 192.168.2.3 (in this example) in the IP Addr box.

B-22 NETGEAR VPN Configuration

Figure B-18

Page 179 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office
Page 179 · click to enlarge
Page 179

e. Click the Pre-Shared Key button.

f. In the Pre-Shared Key dialog box, click the Enter Key button. Enter the DG834G v3's Pre-Shared Key and click OK. In this example, 12345678 is entered. This field is case sensitive.

5. Configure the VPN Client Authentication Proposal .

In this step, you will provide the type of encryption (DES or 3DES) to be used for this connection. This selection must match your selection in the VPN router configuration.

a. In the Network Security Policy list on the left side of the Security Policy Editor window, expand the Security Policy heading by double clicking its name or clicking on the “+” symbol.

b. Expand the Authentication subheading by double clicking its name or clicking on the “+” symbol. Then select Proposal 1 below Authentication.

NETGEAR VPN Configuration B-23

Figure B-19

Page 180 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office
Page 180 · click to enlarge
Page 180

c. In the Authentication Method menu, select Pre-Shared key.

d. In the Encrypt Alg menu, select the type of encryption. In this example, use Triple DES.

e. In the Hash Alg menu, select SHA-1.

f. In the SA Life menu, select Unspecified.

g. In the Key Group menu, select Diffie-Hellman Group 2.

6. Configure the VPN Client Key Exchange Proposal .

In this step, you will provide the type of encryption (DES or 3DES) to be used for this connection. This selection must match your selection in the VPN router configuration.

B-24 NETGEAR VPN Configuration

Figure B-20

Page 181 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office
Page 181 · click to enlarge
Page 181

a. Expand the Key Exchange subheading by double clicking its name or clicking on the “+” symbol. Then select Proposal 1 below Key Exchange.

b. In the SA Life menu, select Unspecified.

c. In the Compression menu, select None.

d. Check the Encapsulation Protocol (ESP) checkbox.

e. In the Encrypt Alg menu, select the type of encryption. In this example, use Triple DES.

f. In the Hash Alg menu, select SHA-1.

g. In the Encapsulation menu, select Tunnel.

h. Leave the Authentication Protocol (AH) checkbox unchecked.

7. Save the VPN Client settings.

From the File menu at the top of the Security Policy Editor window, select Save.

After you have configured and saved the VPN client information, your PC will automatically open the VPN connection when you attempt to access any IP addresses in the range of the remote VPN router’s LAN.

8. Check the VPN Connection .

NETGEAR VPN Configuration B-25

Figure B-21

Page 182 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office
Page 182 · click to enlarge
Page 182

To check the VPN Connection, you can initiate a request from the remote PC to the VPN router’s network by using the Connect option in the ADSL Modem Wireless Router menu bar (see Figure B-22). Since the remote PC has a dynamically assigned WAN IP address, it must initiate the request.

a. Right-click the system tray icon to open the popup menu.

b. Select Connect to open the My Connections list.

c. Choose toDG834G.

The 54 Mbps ADSL Modem Wireless Router Model DG834G will report the results of the attempt to connect. Once the connection is established, you can access resources of the network connected to the VPN router.

NETGEAR DG834G — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office diagram (page 182)
Fig. 94 · Step 2: Configuring the NETGEAR ProSafe VPN Client o…

Right-mouse-click on the system tray icon to open the popup menu.

To perform a ping test using our example, start from the remote PC:

a. Establish an Internet connection from the PC.

b. On the Windows taskbar, click the Start button, and then click Run.

B-26 NETGEAR VPN Configuration

Figure B-22

Page 183 of the NETGEAR DG834G user manual — Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office
Page 183 · click to enlarge
Page 183

c. Type ping -t 192.168.0.1, and then click OK.

This will cause a continuous ping to be sent to the VPN router. After between several seconds and two minutes, the ping response should change from timed out to reply.

Once the connection is established, you can open the browser of the PC and enter the LAN IP address of the VPN router. After a short wait, you should see the login screen of the VPN router (unless another PC already has the VPN router management interface open).

VPN router to the client PC. Run ping tests from the Diagnostics link of the VPN router main menu.

NETGEAR VPN Configuration B-27

Figure B-23 · Figure B-24

Page 184 of the NETGEAR DG834G user manual — Viewing the PC Client’s Connection Monitor and Log Viewer
Page 184 · click to enlarge
Page 184

Monitoring the VPN Tunnel (Telecommuter Example)

Viewing the PC Client’s Connection Monitor and Log Viewer

To view information on the progress and status of the VPN client connection, open the 54 Mbps ADSL Modem Wireless Router Model DG834G Log Viewer.

1. To launch this function, click on the Windows Start button, then select Programs , then 54 Mbps ADSL Modem Wireless Router Model DG834G , then Log Viewer .

connection is due to the VPN tunnel or some reason outside the VPN tunnel.

2. The Connection Monitor screen is shown below:
NETGEAR DG834G — Viewing the PC Client’s Connection Monitor and Log Viewer diagram (page 184)
Fig. 95 · Viewing the PC Client’s Connection Monitor and Log V…

B-28 NETGEAR VPN Configuration

Figure B-25

Page 185 of the NETGEAR DG834G user manual — Viewing the VPN Router’s VPN Status and Log Information
Page 185 · click to enlarge
Page 185

While the connection is being established, the Connection Name field in this menu will show SA before the name of the connection. When the connection is successful, the SA will change to the yellow key symbol.

normal Internet access. If this is the case, you will need to close the VPN connection in order to have normal Internet access.

Viewing the VPN Router’s VPN Status and Log Information

To view information on the status of the VPN client connection, open the VPN router’s VPN Status screen by following the steps below:

1. To view this screen, click the Router Status link of the VPN router’s main menu, then click the VPN Status button. The VPN Status/Log screen for a connection is shown below:

NETGEAR VPN Configuration B-29

Figure B-26

Page 186 of the NETGEAR DG834G user manual — Viewing the VPN Router’s VPN Status and Log Information
Page 186 · click to enlarge
Page 186
2. To view the VPN tunnels status, click the VPN Status link on the right side of the main menu.

B-30 NETGEAR VPN Configuration

Figure B-27

Page 187 of the NETGEAR DG834G user manual — Viewing the VPN Router’s VPN Status and Log Information
Page 187 · click to enlarge
Page 187

NETGEAR VPN Configuration B-31

Page 188 of the NETGEAR DG834G user manual — Viewing the VPN Router’s VPN Status and Log Information
Page 188 · click to enlarge
Page 188

B-32 NETGEAR VPN Configuration

Page 189 of the NETGEAR DG834G user manual — Appendix C Related Documents
Page 189 · click to enlarge
Page 189

Appendix C Related Documents

This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product.

Internet Networking and TCP/IP Addressing

http://documentation.netgear.com/reference/enu/tcpip/index.htm

Wireless Communications http://documentation.netgear.com/reference/enu/wireless/index.htm

Preparing a Computer for Network Access

http://documentation.netgear.com/reference/enu/wsdhcp/index.htm

Virtual Private Networking (VPN) http://documentation.netgear.com/reference/enu/vpn/index.htm

Glossary http://documentation.netgear.com/reference/enu/glossary/index.htm

Document Link · Related Documents C-1

Page 190 of the NETGEAR DG834G user manual — Appendix C Related Documents
Page 190 · click to enlarge
Page 190

C-2 Related Documents

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the NETGEAR DG834G

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the NETGEAR DG834G

Be the first to ask — other owners or our team will answer.

Original document

NETGEAR DG834G manual PDF

190 pages·4.8 MB·Network Router·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…