

NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134
September 2009 208-10462-02 v1.0

©2009 by NETGEAR, Inc. All rights reserved.
NETGEAR and the NETGEAR logo are trademarks of NETGEAR, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders.
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Trademarks · Statement of Conditions


Congratulations on your purchase of a NETGEAR® high-speed wireless router, the Wireless-N 150 ADSL2+ Modem Router.
Before you begin installing your router, check the package contents (see “Unpacking Your New Router” on page 1). Become familiar with the front and back panels of your router—especially the LEDs—and the important information on the router label (see “Hardware Features” on page 2). Then, read the section on “Positioning Your Wireless Router” on page 5 to ensure that you have selected the best location to install your router.
This chapter describes how to set up the wireless modem router on your Local Area Network (LAN) and connect to the Internet. It describes how to set up your wireless modem router for Internet access and configure basic wireless connectivity.
Your router should contain the following items:
– The Smart Wizard Installation Assistant
– Warranty and Support Information
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the carton, including the original packing materials, in case you need to return the product for repair.
Place your router in a suitable area for installation (near an AC power outlet and accessible to the Ethernet cables for your wired computers).
Getting to Know Your Wireless Router 1
– This manual

Before you install and connect your router, take a moment to become familiar with the front and back panels of the router—especially the LEDs on the front panel.
The wireless modem router front panel shown below contains status LEDs.
Power LAN Ports (1-4) DSL Internet Wireless WPS
Getting to Know Your Wireless Router 2

You can use the LEDs to verify various conditions.Table 1 describes each LED.
Table 1. LED Descriptions
Getting to Know Your Wireless Router 3

The back panel of the wireless modem router contains port connections.

1 2 4 3
Viewed from left to right, the rear panel contains the following elements:
Getting to Know Your Wireless Router 4

The label on the bottom of the wireless modem router shows the router’s MAC address, serial number, security PIN, and factory default login information.

Factory Default Reset. Press for 6 seconds to reset the router to its factory default settings.
The wireless modem router lets you access your network from virtually anywhere within the operating range of your wireless network. However, the operating distance or range of your wireless connection can vary significantly depending on the physical placement of your router. For example, the thickness and number of walls the wireless signal must pass through may limit the range. For best results, place your router:
Getting to Know Your Wireless Router 5

Failure to follow these guidelines can result in significant performance degradation or an inability to wirelessly connect to the Internet.
To help you set up your router and get on the Internet quickly, the Resource CD contains a Smart Wizard™. The Smart Wizard walks you through the steps required to connect your router, microfilters, and PC(s); configure your wireless settings; and enable wireless security for your network. When you have finished, you will be Internet ready!
If you have a Macintosh or Linux system, you need to use the manual installation method (see “Installing Your Router Manually (Advanced, Mac, and Linux Users)” on page 11).
You can set up your wireless modem router using one of two methods:
– This is the easiest option. The wizard guides you through the setup process. It automates many of the steps and verifies that the steps have been successfully completed.
– Smart Wizard requires a PC running Microsoft Windows..
Before running the Smart Wizard on a corporate PC to set up your home router, check with your company’s network support staff. Corporate network settings or Virtual Private Network (VPN) client software may conflict with the default settings of a home router. If you are unsure about whether there might be a conflict, use a different computer.
Getting to Know Your Wireless Router 6

If you choose to use the manual setup option, for best results, install and set up your router in this order:
Getting to Know Your Wireless Router 7

Smart Wizard
To use the Smart Wizard, you must be using a PC with Microsoft Windows 7, Windows Vista, Windows XP, or Windows 2000 with Service Pack 2. The Smart Wizard setup procedure should take about 15 minutes to complete. Before using the Smart Wizard to set up your wireless modem router, ensure that:
The NETGEAR Smart Wizard takes you through the procedure to connect your router, ADSL microfilters, and PC(s). It then helps you to configure your wireless settings and enable wireless security for your network. The Smart Wizard guides you through the setup process by automating many of the steps. At each step in the setup process, the Smart Wizard checks to ensure that the steps you perform are successfully completed.
To install your router using the Smart Wizard:
If the CD does not automatically start, browse the CD and double-click on .

The Smart Wizard guides you through installing your router, connecting your router to the Internet, configuring your wireless network settings, and selecting the optimum security protection for your network. If you choose not to select a security option during installation, you can always access the router’s user interface later to select a security option (see “Accessing Your Router After Installation” on page 9).
To ensure optimum performance of your high-speed wireless router, the wireless adapter card for each computer in your network should support the same technology as your router (see the online User Manual for more information).
You are now connected to the Internet!
To set up additional wireless computers in your network for router access and to connect to the Internet, see “Configuring Your Wireless Network” on page 19.
The Smart Wizard only appears when you first install the router or when the router is in its factory default state (for example, if you have reset the router to its factory default settings). If you want to change the settings after installing and configuring your router, you can click the desktop shortcut—a preconfigured shortcut placed on your desktop at installation—to open the router management interface.1 Optionally, you can also open a browser window and log in to the router. After logging in, you can:
For advanced features that are not covered in this manual, see the User Manual on your Resource CD. A link to the on-line User Manual also is available from the router interface.
Installing Your Router Using the Smart Wizard 9

When you run the Resource CD you will have an opportunity to upgrade to the latest available firmware. Once you have configured your wireless-N modem router, when you log in to the wireless-N modem router the Firmware Upgrade Assistant screen displays.
Do not try to go online, turn off the router, shut down the computer, or do anything else to the router until the router finishes restarting and the Ready light has stopped blinking for several seconds!
Installing Your Router Using the Smart Wizard 10

Before installing and connecting your router manually, review the list below and make sure that you have all of the necessary information.
– Host and Domain Name
– Internet Login Name and Password (frequently an email address and password)
– Domain Name Server (DNS) Addresses
– Fixed or Static IP Address
Your ISP should have provided you with all the information needed to connect to the Internet. If you cannot locate this information, ask your ISP.
If you have not already done so:
Installing Your Router Manually (Advanced, Mac, and Linux Users) 11

ADSL technology uses the same wires as your telephone service. However, ADSL adds signals to the telephone lines which create noise in the telephone service. You must use ADSL microfilters to filter out these signals before they reach your telephone.
If you purchased the wireless modem router in a country where a microfilter is not included, you must acquire one.

Each device such as a telephone, fax machine, answering machine, or caller ID display will require an ADSL microfilter.
Do not connect the wireless modem router to the ADSL line through a microfilter unless the microfilter is a combination microfilter/splitter specifically designed for this purpose. Doing so will prevent block your connection to the Internet. If you have any doubts about this, connect the wireless modem router directly to the ADSL line.
Use an ADSL microfilter with built-in splitter when there is a single wall outlet which must provide connectivity for both the wireless modem router and telephone equipment.

Installing Your Router Manually (Advanced, Mac, and Linux Users) 12

Before you install your wireless modem router, make sure that the Internet Protocol (TCP/IP) Property settings on your computer are set to “automatically obtain an IP address” using DHCP and “Obtain DNS server address automatically.” You can check these settings by looking at the TCP/IP Properties of your Internal Network Connections, which are accessible through the Control Panel of your computer. If you are unsure about this, refer to the documentation for your computer or see the link to TCP/IP Addressing in “Related Documents” on page 34.
If you are replacing an existing router, disconnect it completely from your network and set it aside before starting to install your new router.
To connect the wireless modem router, the ADSL filter and the computer:
If you purchased the DGN1000 in a country where an ADSL filter is not included, you must acquire one.

Installing Your Router Manually (Advanced, Mac, and Linux Users) 13


To use a one-line filter with a separate splitter, insert the splitter into the phone outlet, connect the one-line filter to the splitter, and connect the phone to the filter.
Installing Your Router Manually (Advanced, Mac, and Linux Users) 14


Improperly connecting a filter to your wireless modem router will block your ADSL connection.
Installing Your Router Manually (Advanced, Mac, and Linux Users) 15


D
D
Verify that your router is connected correctly by checking the wireless modem router status lights.
Now, turn on your computer. If software usually logs you in to your Internet connection, do not run that software. Cancel it if it starts automatically. Verify the following:
Installing Your Router Manually (Advanced, Mac, and Linux Users) 16

When configuring your wireless router manually, you must log in to your wireless modem router to set it up initially and to make any changes to your wireless router’s settings later.
To access the router:
You can also enter either of these addresses to connect to your wireless router:
http://www.routerlogin.net or http://www.routerlogin.com.

A login window similar to the one shown in Figure 11 will display.

The router user name and password are not the same as any user name or password you may use to log in to your Internet connection.
The Main menu will display.
Installing Your Router Manually (Advanced, Mac, and Linux Users) 17


If you cannot connect to the wireless router, check the Internet Protocol (TCP/IP) properties in the Network Connections section of your Control Panel. It should be set to obtain both IP and DNS server addresses automatically. For assistance, see your computer documentation or see the links in “Related Documents” on page 34.
You should now be connected to the Internet!
If you do not connect successfully:
If problems persist, register your NETGEAR product and contact NETGEAR Technical Support.
Installing Your Router Manually (Advanced, Mac, and Linux Users) 18

After installing your router, you must log into the router to complete your wireless setup. The wireless network settings of the router must match the wireless network settings of any wireless devices that connect wirelessly to the router (such as wireless adapter cards and wireless computers).
For a wireless connection, the router and each wireless computer must use the same SSID, also called the wireless network name, and the same wireless security. NETGEAR strongly recommends that you use wireless security.
Indoors, computers can connect over wireless networks at a range of several hundred feet. This can allow others outside of your immediate area to access your network.
The Wireless Settings screen lets you set your wireless network connections and the wireless security option for your network and router. To configure the wireless network, you can either manually specify your network name (SSID) and your wireless security settings (see “Setting Your SSID and Wireless Security” on page 20) or, if all of the clients in your network are WPS capable, you can use Wi-Fi Protected Setup (WPS) to automatically configure your router and, at the same time, add the WPS-capable devices to your secure wireless network (see “Using Push 'N' Connect (WPS) to Add Wireless Devices” on page 21). You can also use Push 'N' Connect (WPS) to add WPS-capable devices after you have set your SSID and wireless security using the manual or traditional method (the preferred option).
If you configure the router from a wireless computer and you change the router’s SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change your computer’s wireless settings to match the router’s new settings. To avoid this situation, you can use a computer that is connected to the router with an Ethernet cable.
For a complete overview of all the security configurations that can be implemented on this router, see the on-line User Manual. A link to the User Manual is on the Resource CD.
Configuring Your Wireless Network 19

To specify the wireless settings, you must know the following:
To set up basic wireless connectivity and wireless security on your router:
You can also enter either of these addresses to connect to your wireless router:
http://www.routerlogin.net or http://www.routerlogin.com.
The SSID of any wireless adapters must match the SSID you configure in the wireless modem router. If they do not match, you will not get a wireless connection.
Configuring Your Wireless Network 20

To set up your computers for wireless connectivity:
For a Windows PC, go to the Control Panel and select Network Connections.
Check the Wireless Connections Properties and ensure that TCP/IP Properties are set to Obtain an IP address automatically.
To access the Internet from any computer connected to your wireless modem router, launch a browser such as Microsoft Internet Explorer or Mozilla Firefox. You should see the wireless modem router’s Internet LED blink, indicating communication to the ISP.
If your wireless clients support Wi-Fi Protected Setup (WPS), you can use this feature to connect the wireless client securely and easily to the router. Look for the symbol on your client device.1
NETGEAR’s Push 'N' Connect feature is based on the Wi-Fi Protected Setup (WPS) standard. All other Wi-Fi-certified and WPS-capable products should be compatible with NETGEAR products that implement Push 'N' Connect.
Configuring Your Wireless Network 21

You can use WPS in one of two ways:
The first method is explained here. For more information on the second method, see the User Manual.
If your network consists of WPS capable devices and non-WPS capable devices, NETGEAR suggests that you set up your wireless network and security settings first using the manual or traditional method (see “Setting Your SSID and Wireless Security” on page 20), and use WPS only for adding additional WPS capable devices.
If you choose to use WPS, WEP with shared-key authentication is not supported by WPS.
To add a wireless device using WPS:
The WPS LED on the router will continue to blink while the 2-minute window is open. When the LED stops blinking it will return to solid green. (The LED will only turn off if no security has been configured on the router.)
Then, to access the Internet, launch a browser (such as Microsoft Internet Explorer or Mozilla Firefox) from the device. You should see the wireless modem router’s Internet LED blink, indicating communication with the ISP.
For more information on setting up your wireless network and configuring your wireless security settings, see the User Manual. A link to the online User Manual is on your Resource CD.
Configuring Your Wireless Network 22

This chapter gives information about troubleshooting your wireless modem router. After each problem description, instructions are provided to help you diagnose and solve the problem. For the common problems listed, go to the section indicated.
Go to “Basic Functioning” on page 23.
Go to “Troubleshooting the Web Configuration Interface” on page 25.
Go to “Troubleshooting Internet Browsing” on page 28.
Go to “Troubleshooting the ISP Connection” on page 26.
Go to “To restore the factory default configuration settings, press the reset button on the bottom of the router following the steps below.” on page 30.
Go to “Restoring the Default Configuration and Password” on page 30.
After you turn on power to the router, the following sequence of events should occur:
a. The LAN port LEDs are lit for any local ports that are connected.
b. The ADSL Internet port LED is lit.
Troubleshooting 23

If a port’s LED is lit, a link has been established to the connected device. If any of these conditions does not occur, refer to the appropriate following section.
If the Power and other LEDs are off when your router is turned on:
If the error persists, you have a hardware problem and should contact technical support.
When the router is turned on, it performs a power-on self test. If the Power LED turns red after a few seconds or at any other time during normal operation, there is a fault within the router. The power LED also turns red when you depress the factory default reset push button, and blinks red 3 times when that button is released. However, in this case, the wireless modem router is working normally.
If the power LED turns red to indicate a router fault:
If the power LED is still red one minute after power up:
If the error persists, you might have a hardware problem and should contact technical support.
If either the LAN LEDs or ADSL Internet LED do not light when the Ethernet connection is made, check the following:
Troubleshooting 24

If you are unable to access the router’s Web Configuration interface from a computer on your local network, check the following:
If the router does not save changes you have made in the Web Configuration Interface, check the following:
Troubleshooting 25

If your router is unable to access the Internet, you should check the ADSL connection, then the Internet TCP/IP connection.
If your router is unable to access the Internet, you should first determine whether you have an ADSL link with the service provider. The state of this connection is indicated with the Internet LED.
Internet LED Green or Blinking Green
If your Internet LED is green or blinking green, then you have a good ADSL connection. You can be confident that the service provider has connected your line correctly and that your wiring is correct.
If the Internet LED is red, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.
If disconnecting telephones does not result in a green Internet LED, there may be a problem with your wiring. If the telephone company has tested the ADSL signal at your Network Interface Device (NID), then you may have poor quality wiring in your house.
If the Internet LED is off, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.
If disconnecting telephones does not result in a green Internet LED the problem may be one of the following:
Internet LED Red · Internet LED Off · Troubleshooting 26

If your wireless modem router is unable to access the internet, and your Internet LED is red, you should determine whether the wireless modem router is able to obtain a Internet IP address from the ISP. Unless you have been assigned a static IP address, your wireless modem router must request an IP address from the ISP. You can determine whether the request was successful using the browser interface.
To check the Internet IP address from the browser interface:
If your router is unable to obtain an IP address from the ISP, the problem may be one of the following:
– Inform your ISP that you have bought a new network device, and ask them to use the router’s MAC address; or
– Configure your router to spoof your computer’s MAC address. This can be done in the Basic Settings menu. Refer to the online help in the wireless modem router main menu.
Troubleshooting 27

The PPPoE or PPPoA connection can be debugged as follows:
If all of the steps indicate “OK” then your PPPoE or PPPoA connection is up and working.
If any of the steps indicates “Failed”, you can attempt to reconnect by clicking Connect. The wireless modem router will continue to attempt to connect indefinitely.
If you cannot connect after several minutes, you may be using an incorrect service name, user name, or password. There also may be a provisioning problem with your ISP.
Unless you connect manually, the wireless modem router will not authenticate using PPPoE or PPPoA until data is transmitted to the network.
If your wireless modem router can obtain an IP address but your computer is unable to load any Web pages from the Internet:
A DNS server is a host on the Internet that translates Internet names (such as www addresses) to numeric IP addresses. Typically your ISP will provide the addresses of one or two DNS servers for your use. If you entered a DNS address during the wireless modem router’s configuration, reboot your computer and verify the DNS address as described in “Preparing Your Network” on page 34. Alternatively, you can configure your computer manually with DNS addresses, as explained in your operating system documentation.
If your computer obtains its information from the wireless modem router by DHCP, reboot the computer and verify the wireless modem router address as described in “Preparing Your Network” on page 34.
Troubleshooting 28

Most TCP/IP terminal devices and routers contain a ping utility that sends an echo request packet to the designated device. The device then responds with an echo reply. Troubleshooting a TCP/IP network is made easy by using the ping utility in your computer.
You can ping the router from your computer to verify that the LAN path to your router is set up correctly.
To ping the router from a PC running Windows 95 or later:
ping 192.168.0.1
You should see a message like this one:
Pinging <IP address> with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
If the path is not functioning correctly, you could have one of the following problems: • Wrong physical connections
– Make sure the LAN port LED is on. If the LED is off, follow the instructions in “LAN or Internet Port LEDs Not On” on page 24.
– Check that the corresponding Link LEDs are on for your network interface card and for the hub ports (if any) that are connected to your workstation and router. • Wrong network configuration
– Verify that the Ethernet card driver software and TCP/IP software are both installed and configured on your PC or workstation.
Request timed out · Troubleshooting 29

– Verify that the IP address for your router and your workstation are correct and that the addresses are on the same subnet.
After verifying that the LAN path works correctly, test the path from your PC to a remote device. From the Windows run menu, type:
PING -n 10 <IP address>
where <IP address> is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies as in the previous section are displayed. If you do not receive replies:
This section explains how to restore the factory default configuration settings, changing the router’s administration password to password and the IP address to 192.168.0.1. You can erase the current configuration and restore factory defaults by pressing the reset button on the bottom of the router. Use this method for cases when the administration password or IP address is not known.
To restore the factory default configuration settings, press the reset button on the bottom of the router following the steps below.
Troubleshooting 30

This appendix provides technical specifications for the wireless modem router.
Network Protocol and Standards Compatibility
Data and Routing Protocols: TCP/IP, RIP-1, RIP-2, DHCP, PPPoE or PPPoA, RFC 1483 Bridged or Routed Ethernet, and RFC 1577 Classical IP over ATM
Meets requirements of: FCC Part 15 Class B; VCCI Class B; EN 55 022 (CISPR 22), Class B

To reset you router to the default settings, see “Restoring the Default Configuration and Password” on page 30. Your router will return to the factory configuration settings that are shown in the table below.
User Login URL http://www.routerlogin.net or http://www.routerlogin.com
User Name (case sensitive) admin
Login Password (case sensitive) password
WAN MAC Address Use Default address
WAN MTU Size 1492
Lan IP 192.168.0.1
Subnet Mask 255.255.255.0
DHCP Starting IP Address 192.168.0.2
DHCP Ending IP Address 192.168.0.254

Time Zone Adjusted for Daylight Saving Time
Inbound (communications coming in from the Internet)
Disabled (except traffic on port 80, the http port)
Outbound (communications going out to the Internet)
Source MAC filtering Disabled
Transmission Speed Autoa
Country/Region United States (in North America; otherwise, varies by region)
Operating Mode Up to 130 Mbps
Authentication Type Open System
Wireless Card Access List All wireless stations allowed
a. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary.
Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.

This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product.
ITCP/IP Networking Basics http://documentation.netgear.com/reference/enu/tcpip/index.htm
Wireless Networking Basics http://documentation.netgear.com/reference/enu/wireless/index.htm
Preparing Your Network http://documentation.netgear.com/reference/enu/wsdhcp/index.htm
Virtual Private Networking Basics http://documentation.netgear.com/reference/enu/vpn/index.htm
Glossary http://documentation.netgear.com/reference/enu/glossary/index.htm
Document Link · Related Documents 34

Product Registration, Support, and Documentation
Register your product at http://www.NETGEAR.com/register You must register before you can use our telephone support service. Product updates and Web support are always available by going to: http://kbserver.netgear.com/
Setup documentation is available on the CD, on the support website, and on the documentation website. When the wireless modem router is connected to the Internet, click the KnowledgeBase link to view support information or click the Documentation link to view the online User Manual for this wireless modem router.
Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications
Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.