
NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA
208-10033-01 2006-2

© 2006 by NETGEAR, Inc. All rights reserved.
NETGEAR is a trademark of Netgear, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders.
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Trademarks · Statement of Conditions


This chapter describes how to set up the router on your Local Area Network (LAN) and connect to the Internet. It describes how to set up your wireless ADSL modem router for Internet access and configure basic wireless connectivity.
The product package should contain the following items:
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the carton, including the original packing materials, in case you need to return the product for repair.

The Router’s Front Panel The wireless ADSL modem router front panel shown below contains status LEDs.


1 2 3 4
You can use the LEDs to verify various conditions. Table 1-1 describes each LED.
Table 1-1. LED Descriptions

The rear panel of the wireless ADSL modem router contains port connections.

Viewed from left to right, the rear panel contains the following elements:
You need to prepare the following before you can set up your router:

Depending on how your ISP set up your Internet account, you need one or more of these configuration parameters to connect your router to the Internet:
Your ISP should have provided you with all the information needed to connect to the Internet. If you cannot locate this information, you can ask your ISP to provide it.
You have two methods available for setting up your wireless ADSL modem router:
— This option is the easiest. The Smart Wizard on the CD guides you through the setup
process, automating many of the steps, and verifying that necessary conditions exist and that steps you perform have been successfully completed.
— This option requires a PC running Microsoft Windows 98SE or higher. • Manual Setup: Manually set up your wireless ADSL modem router.
— This option is best if you are replacing an existing wireless ADSL modem router or are
technically knowledgeable.
— Use this option if you are using a computer that does not run Microsoft Windows.
— The manual setup procedures are documented in this manual.
Use the setup option that best suites you.

The Smart Wizard setup process should take about 20 minutes to complete.
The CD will automatically start and detect the language you are using on your PC.
Autorun.
Use the topics and procedures below to manually set up your wireless ADSL modem router.
ADSL technology uses the same wires as your telephone service. However, ADSL adds signals to the telephone lines which create noise in the telephone service. You must use ADSL microfilters to filter out these signals before they reach your telephone.
is not included, you must acquire one.

Each device such as a telephone, fax machine, answering machine, or caller ID display will require an ADSL microfilter.
microfilter unless the microfilter is a combination microfilter/splitter specifically designed for this purpose. Doing so will prevent block your connection to the Internet. If you have any doubts about this, connect the wireless ADSL modem router directly to the ADSL line.
ADSL Microfilter with Built-In Splitter
Use an ADSL microfilter with built-in splitter when there is a single wall outlet which must provide connectivity for both the wireless ADSL modem router and telephone equipment.
For the initial connection to your router, your computer has to be set to automatically get its TCP/IP configuration from the router via DHCP. This is usually the case. The NETGEAR Smart Wizard CD automatically takes care of this requirement. For manual setup, refer to the documentation that came with your computer.
There are four steps to setting up your wireless ADSL modem router:

Follow the steps below to connect your router to your network. Before you begin, locate the ADSL configuration information from your Internet Service Provider (ISP).
included, you must acquire one.
a. You need to install an ADSL filter for every telephone that uses the same phone line as your wireless ADSL modem router. Select the filter that came with your wireless ADSL modem router.
,INE
0HONE
!$3,

b. Two-Line Filter Example. Insert the two-line filter into the phone outlet and connect the phone to the phone line connector (A):
0HONE
A
phone outlet, connect the one-line filter to the splitter, and connect the phone to the filter.
!$3,

a. Using the included phone cable with RJ-11 jacks, connect the ADSL port (B) of the wireless ADSL modem router to the ADSL port (C) of the two-line filter.

will block your ADSL connection.

b. Connect the Ethernet cable (D) from a wireless ADSL modem router LAN port to the Ethernet adapter in your computer.

c. Connect the power adapter to the router and plug it in to a power outlet. Verify the following:
The power light is lit after turning on the router.
The test light comes on briefly, then goes off.
The wireless light is lit after turning on the router.
The ADSL light is green, indicating you are connected to the ADSL network. d. Now, turn on your computer. If software usually logs you in to your Internet connection, do not run that software. Cancel it if it starts automatically. Verify the following:
The local lights are lit for any connected computers.

configuring for DHCP, please see the documentation that came with your computer or “Preparing a Computer for Network Access”.
a. Type http://192.168.0.1 in the address field of a browser such as Internet Explorer or Netscape® Navigator.

This login window opens:

Enter admin for the user name and password for the password, both in lower case letters.

b. After logging in, you will see the menu below.

In either case, use to the configuration parameters your ISP provided to assure that the configuration settings for your Internet connection are correct.
Your wireless ADSL modem router is now configured to provide Internet access for your network. Your wireless ADSL modem router automatically connects to the Internet when one of your computers requires access. It is not necessary to run a dialer or login application such as Dial-Up Networking or Enternet to connect, log in, or disconnect. These functions are performed automatically by the wireless ADSL modem router as needed.
To access the Internet from any computer connected to your wireless ADSL modem router, launch a browser such as Microsoft Internet Explorer or Netscape Navigator. You should see the wireless ADSL modem router’s Internet LED blink, indicating communication to the ISP. The browser should begin to display a Web page.

Follow the instructions below to set up and test basic wireless connectivity. Once you have established basic wireless connectivity, you can enable security settings appropriate to your needs.
wireless ADSL modem router. If they do not match, you will not get a wireless connection.
router’s SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change the wireless settings of your computer to match the router’s new settings.
Program the wireless adapter of your computers to have the same wireless network name (SSID) as the wireless ADSL modem router. Check that they have a wireless link and are able to obtain an IP address by DHCP from the router.

maximum range of up to 300 feet. Such distances can allow for others outside of your immediate area to access your network.
Unlike wired network data, your wireless data transmissions can extend beyond your walls and can be received by anyone with a compatible adapter. For this reason, use the security features of your wireless equipment. The wireless ADSL modem router provides highly effective security features which are covered in detail in full reference manual that is available from a link on the CD as well as a link in the main menu of your router. Follow the instructions in the full manual and in the router help screens to deploy the security features appropriate to your needs.

This chapter gives information about troubleshooting your wireless ADSL modem router. After each problem description, instructions are provided to help you diagnose and solve the problem. For the common problems listed, go to the section indicated.
Go to “Basic Functioning” on page 2-1.
Go to “Basic Functioning” on page 2-1.
Go to “Troubleshooting the Web Configuration Interface” on page 2-3.
Go to “Troubleshooting the ISP Connection” on page 2-4.
Go to “Using the Reset Button” on page 2-9.
Go to “Restoring the Default Configuration and Password” on page 2-9.
After you turn on power to the router, the following sequence of events should occur:
a. The Test LED is not lit.

b. The LAN port LEDs are lit for any local ports that are connected.
c. The ADSL Internet port LED is lit.
If a port’s LED is lit, a link has been established to the connected device. If a LAN port is connected to a 100 Mbps device, verify that the port’s LED is green. If the port is 10 Mbps, the LED will be amber.
If any of these conditions does not occur, refer to the appropriate following section.
If the Power and other LEDs are off when your router is turned on:
If the error persists, you have a hardware problem and should contact technical support.
When the router is turned on, the Test LED turns on for about 10 seconds and then turns off. If the Test LED does not turn on, or if it stays on, there is a fault within the router.
If you experience problems with the Test LED:
If all LEDs including the Test LED are still on one minute after power up:
If the error persists, you might have a hardware problem and should contact technical support.

If either the LAN LEDs or ADSL Internet LED do not light when the Ethernet connection is made, check the following:
If you are unable to access the router’s Web Configuration interface from a computer on your local network, check the following:
Note: If your computer’s IP address is shown as 169.254.x.x: Recent versions of Windows and MacOS will generate and assign an IP address if the computer cannot reach a DHCP server. These auto-generated addresses are in the range of 169.254.x.x. If your IP address is in this range, check the connection from the computer to the router and reboot your computer.

If the router does not save changes you have made in the Web Configuration Interface, check the following:
If your router is unable to access the Internet, you should check the ADSL connection, then the Internet TCP/IP connection.
If your router is unable to access the Internet, you should first determine whether you have an ADSL link with the service provider. The state of this connection is indicated with the Internet LED.
ADSL Internet LED Green or Blinking Green
If your ADSL Internet LED is green or blinking green, then you have a good ADSL connection. You can be confident that the service provider has connected your line correctly and that your wiring is correct.
ADSL Internet LED Blinking Yellow
If your ADSL Internet LED is blinking yellow, then your wireless ADSL modem router is attempting to make an ADSL connection with the service provider. The LED should turn green within several minutes.
If the Internet LED does not turn green, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.
If disconnecting telephones does not result in a green ADSL Internet LED, there may be a problem with your wiring. If the telephone company has tested the ADSL signal at your Network Interface Device (NID), then you may have poor quality wiring in your house.

ADSL Internet LED Off
If the ADSL Internet LED is off, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.
If disconnecting telephones does not result in a green ADSL Internet LED the problem may be one of the following:
If your wireless ADSL modem router is unable to access the internet, and your Internet LED is green or blinking green, you should determine whether the wireless ADSL modem router is able to obtain a Internet IP address from the ISP. Unless you have been assigned a static IP address, your wireless ADSL modem router must request an IP address from the ISP. You can determine whether the request was successful using the browser interface.
To check the Internet IP address from the browser interface:
If your router is unable to obtain an IP address from the ISP, the problem may be one of the following:
Verify with your ISP the Multiplexing Method and parameter value, and update the router’s ADSL Settings accordingly.

Ask your ISP whether they require PPP over Ethernet (PPPoE) or PPP over ATM (PPPOA) login.
Inform your ISP that you have bought a new network device, and ask them to use the router’s MAC address.
Configure your router to spoof your computer’s MAC address. This can be done in the Basic Settings menu. Refer to the online help in the wireless ADSL modem router main menu.
The PPPoA or PPPoA connection can be debugged as follows:
If you cannot connect after several minutes, you may be using an incorrect Service Name, User Name or Password. There also may be a provisioning problem with your ISP.
authenticate using PPPoE or PPPoA until data is transmitted to the network.

If your wireless ADSL modem router can obtain an IP address but your computer is unable to load any Web pages from the Internet:
A DNS server is a host on the Internet that translates Internet names (such as www addresses) to numeric IP addresses. Typically your ISP will provide the addresses of one or two DNS servers for your use. If you entered a DNS address during the wireless ADSL modem router’s configuration, reboot your computer and verify the DNS address as described in “Preparing a Computer for Network Access”. Alternatively, you can configure your computer manually with DNS addresses, as explained in your operating system documentation.
If your computer obtains its information from the wireless ADSL modem router by DHCP, reboot the computer and verify the wireless ADSL modem router address as described in “Preparing a Computer for Network Access”.
Most TCP/IP terminal devices and routers contain a ping utility that sends an echo request packet to the designated device. The device then responds with an echo reply. Troubleshooting a TCP/IP network is made very easy by using the ping utility in your computer.
You can ping the router from your computer to verify that the LAN path to your router is set up correctly.
To ping the router from a PC running Windows 95 or later:
ping 192.168.0.1
You should see a message like this one:

Pinging <IP address> with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message: Request timed out If the path is not functioning correctly, you could have one of the following problems: • Wrong physical connections — Make sure the LAN port LED is on. If the LED is off, follow the instructions in “LAN
or ADSL Internet Port LEDs Not On” on page 2-3. — Check that the corresponding Link LEDs are on for your network interface card and
for the hub ports (if any) that are connected to your workstation and router. • Wrong network configuration — Verify that the Ethernet card driver software and TCP/IP software are both installed
and configured on your PC or workstation. — Verify that the IP address for your router and your workstation are correct and that the
addresses are on the same subnet.
After verifying that the LAN path works correctly, test the path from your PC to a remote device. From the Windows run menu, type:
PING -n 10 <IP address>
where is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies as in the previous section are displayed. If you do not receive replies:
— Check that your PC has the IP address of your router listed as the default gateway. If the IP
configuration of your PC is assigned by DHCP, this information will not be visible in your PC’s Network Control Panel. Verify that the IP address of the router is listed as the TCP/IP default gateway as described in “Preparing a Computer for Network Access”.
— Check to see that the network address of your PC (the portion of the IP address specified
by the netmask) is different from the network address of the remote device.
— If your ISP assigned a host name to your PC, enter that host name as the Account Name in
the Basic Settings menu.

This section explains how to restore the factory default configuration settings, changing the router’s administration password to password and the IP address to 192.168.0.1. You can erase the current configuration and restore factory defaults in two ways:
To restore the factory default configuration settings without knowing the administration password or IP address, you must use the Default Reset button on the rear panel of the router.



This appendix provides technical specifications for the wireless ADSL modem router.
Network Protocol and Standards Compatibility
Data and Routing Protocols: TCP/IP, RIP-1, RIP-2, DHCP, PPPoE or PPPoA, RFC 1483 Bridged or Routed Ethernet, and RFC 1577 Classical IP over ATM
Meets requirements of: FCC Part 15 Class B; VCCI Class B; EN 55 022 (CISPR 22), Class B
WAN: ADSL, Dual RJ-11, pins 2 and 3 T1.413, G.DMT, G.Lite ITU Annex A or B

A-2 Technical Specifications

This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product.
Internet Networking and TCP/IP Addressing http://documentation.netgear.com/reference/enu/tcpip/index.htm
Wireless Communications http://documentation.netgear.com/reference/enu/wireless/index.htm
Preparing a Computer for Network Access http://documentation.netgear.com/reference/enu/wsdhcp/index.htm
Virtual Private Networking (VPN) http://documentation.netgear.com/reference/enu/vpn/index.htm
Glossary http://documentation.netgear.com/reference/enu/glossary/index.htm
Document Link · Related Documents B-1

B-2 Related Documents
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.