EN
NETGEAR logo
Official user manual

NETGEAR WND3700v4

2 pages·642 KB·Network Router·PDF·ENDEFRITNLJA
NETGEAR WND3700v4
Table of Contents 17 sections Installation Guide · N600 Wireless Dual Band Gigabit Router WNDR3700v4 · Step 1: · Step 2: Connect one end of the yellow Ethernet cable · … ShowHide
Page 1 of the NETGEAR WND3700v4 user manual — Wait for the 2.4 GHz LED ( )
Page 1 · click to enlarge
Page 1
NETGEAR WND3700v4 — Installation Guide diagram (page 1)
Fig. 1 · Installation Guide
NETGEAR WND3700v4 — Installation Guide diagram (page 1)
Fig. 2 · Installation Guide
NETGEAR WND3700v4 — Installation Guide diagram (page 1)
Fig. 3 · Installation Guide

Installation Guide

N600 Wireless Dual Band Gigabit Router WNDR3700v4

Step 1:

Step 2: Connect one end of the yellow Ethernet cable

Unplug the power to turn off your modem.

to your modem, and the other end to the Internet port on your router.

Step 5:

Package Contents

Connect your computer to the router

Use another Ethernet cable to establish a wired connection as shown in this diagram.

NETGEAR WND3700v4 — Connect your computer to the router diagram (page 1)
Fig. 4 · Connect your computer to the router

Optionally, connect wirelessly by using the preset wireless security settings, located on the bottom label.

Step 3:

Step 6:

Plug in the power to turn on your modem.

Open a browser.

Step 4:

If the web page does not display, close and re-open the browser, then enter

Wait approximately 2 minutes

Connect the power adapter to the router, then plug it into an outlet.

until your modem turns on.

http://www.routerlogin.net

Wait for the 2.4 GHz LED ( )

If your modem has a battery backup,

2.4 GHz to light.

in the address bar, or check the “Troubleshooting” section on the back of this installation guide.

first remove and reinsert the battery before connecting your modem to power.

If none of the LEDs light, make sure that the Power On/Off button is in the on position (pushed in).

Show 12 more labels / short text on this page
(not included) · Laptop or desktop · computer · DSL or cable · Internet · Power On/Off · Power On/Off · Modem · Ethernet cable · N600 Wireless Router · N600 Wireless Router · Power adapter
Page 2 of the NETGEAR WND3700v4 user manual — WPS Method
Page 2 · click to enlarge
Page 2

Connect Wireless Devices to Your Router

Troubleshooting

Preset Wireless Security

Choose either the manual or Wi-Fi Protected Setup (WPS) method to add wireless computers, and other devices to your wireless network.

The browser cannot display the web page.

This product has a unique WiFi network name (SSID) and network key (password). The default SSID and password are uniquely generated for every device (like a serial number), to protect and maximize your wireless security. This information is on the label on the bottom of the product.

  • Make sure that the computer is connected to one of the four LAN Ethernet ports, or wirelessly to the router.
  • Make sure that the Wireless LED is lit.
  • Close and reopen the browser to make sure that the browser does not cache the previous page.
  • Browse to <a href="http://www.routerlogin.net" rel="nofollow noopener" target="_blank">http://www.routerlogin.net</a> .
  • If the computer is set to a static or fixed IP address (this setting is uncommon), change it to obtain an IP address automatically from the router.

Manual Method

1. Open the software utility that manages your wireless connections on the wireless device that you want to connect to your router (iPhone, laptop, computer, gaming device). This utility scans for all wireless networks in your area.

NETGEAR recommends that you do not change the preset SSID or password. If you do change the settings, the information on the bottom of the product does not apply.

NETGEAR WND3700v4 — Manual Method diagram (page 2)
Fig. 5 · Manual Method
2. Look for the preset NETGEAR wireless network name (SSID), and select it. The SSID is on the product label on the bottom of the router.

Support

Thank you for purchasing this NETGEAR product.

3. Enter the preset password (or your custom password if you changed it), and click Connect .

After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com. NETGEAR recommends that you use only the official NETGEAR support resources.

4. Repeat steps 1–3 to add other wireless devices.

Find the preset wireless settings on your router and record them here:

WPS Method

WiFi network name (SSID)

If your wireless device supports WPS (Wi-Fi Protected Setup)—NETGEAR calls this method Push 'N' Connect—you might be prompted to press the WPS button on the router instead of entering a password. If you are prompted to press the WPS button:

Network key (password)

You can get the user manual online at http://downloadcenter.netgear.com or through a link in the product’s user interface. For the current EU Declaration of Conformity, visit http://support.netgear.com/app/answers/detail/a_id/11621/. For regulatory compliance information, visit http://www.netgear.com/about/regulatory/. See the regulatory compliance document before connecting the power supply.

If you change the preset wireless settings, record them here:

Wireless network name (SSID)

1. Press the WPS button on the router.
2. Within 2 minutes, press the WPS button on the client device, or follow the WPS instructions that came with your wireless device to complete the WPS process. The device is then connected to your router.

Network key (password)

InternetWiFi ConnectionRouter Settings STATUS GOODSTATUS ConnectedClick here Network MapParental ControlsReadySHARE Number of devices 16Click hereClick here

Get the genie app.

Download the free genie app from www.NETGEAR.com/genie. Easily share media, files, and printers on the network from your smartphone, tablet, or laptop.

If necessary to retrieve or update your password, type http://www.routerlogin.net in a web browser, and log in using the default user name (admin) and password (password).

3. Repeat this process to add other WPS wireless devices.

Select Wireless Settings to locate your wireless password.

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved.

NETGEAR WND3700v4 — WPS Method diagram (page 2)
Fig. 6 · WPS Method

August 2014

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the NETGEAR WND3700v4

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the NETGEAR WND3700v4

Be the first to ask — other owners or our team will answer.

Original document

NETGEAR WND3700v4 manual PDF

2 pages·642 KB·Network Router·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…