

NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134 USA
202-10397-04 July 2009 v1.3

©2009 by NETGEAR, Inc. All rights reserved.
Product Registration, Support, and Documentation
Register your product at http://www.netgear.com/register. Registration is required before you can use our telephone support service. Product updates and Web support are always available at http://www.netgear.com/support.
Setup documentation is available on the CD, on the support website, and on the documentation website. When the wireless router is connected to the Internet, click the Knowledge Base or the Documentation link under Web Support on the main menu to view support information.
NETGEAR and the NETGEAR logo are registered trademarks, and RangeMax and Smart Wizard are trademarks of NETGEAR. Inc. in the United States and/or other countries. Microsoft, Windows, and Windows NT are registered trademarks and Windows Vista is a trademark of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders.
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the Wireless-N 300 Router Model WNR2000 has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations.
Es wird hiermit bestätigt, daß das Wireless-N 300 Router Model WNR2000 gemäß der im BMPT-AmtsblVfg 243/1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.B. Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung.
Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.
This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.

Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries under the following conditions and/or with the following restrictions:


FCC Requirements for Operation in the United States
Federal Communications Commission (FCC) Compliance Notice:
Radio Frequency Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.
FCC Guidelines for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Declaration Of Conformity
We NETGEAR, Inc., 4500 Great America Parkway, Santa Clara, CA 95054, declare under our sole responsibility that the model WNR2000 Wireless-N 300 Router Model WNR2000 complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:
Wireless-N 300 Router Model WNR2000
Tested to Comply with FCC Standards
Modifications made to the product, unless expressly approved by NETGEAR, Inc., could void the user's right to operate the equipment.
This Class B digital apparatus complies with Canadian ICE-003. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
Operation is subject to the following two conditions,
(1) this device may not cause interference and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications
Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.
Industry Canada (IC)

Product and Publication Details




This chapter describes the settings for your Internet connection and your wireless local area network (LAN) connection. When you perform the initial configuration of your wireless router using the Resource CD as described in the NETGEAR Wireless Router Setup Manual, these settings are specified automatically for you. This chapter provides further details about these connectivity settings, as well as instructions on how to log in to the router for further configuration.
configuration, as described in the NETGEAR Wireless Router Setup Manual.
For first-time installation of your wireless router, refer to the NETGEAR Wireless Router Setup Manual. The Setup Manual explains how to launch the NETGEAR Smart Wizard on the Resource CD to step you through the procedure to connect your router, modem, and computers. The Smart Wizard will assist you in configuring your wireless settings and enabling wireless security for your network. After initial configuration using the Setup Manual, you can use the information in this User Manual to configure additional features of your wireless router.
For installation instructions in a language other than English, refer to the language options on the Resource CD.

When the wireless router is connected to your network, you can access and configure the router using your browser.
To access the router:

address field of your browser, and then pressing Enter:
If these URLs do not work, you must type the IP address of the router, for example, http://www.192.168.1.1.
password you might use to log in to your Internet connection.
1-2 Configuring Basic Connectivity

The Checking for Firmware Updates screen appears unless you previously cleared the Check for Updated Firmware Upon Log-in check box.

If the router discovers a newer version of firmware, the message on the left displays when you log in. If no new firmware is available, the message on the right displays.


To automatically update to the new firmware, click Yes to allow the router to download and install the new firmware file from NETGEAR.
Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, it could corrupt the firmware.
When the upload is complete, your router automatically restarts. The update process typically takes about 1 minute.
Configuring Basic Connectivity 1-3


page is the Router Upgrade screen. Otherwise, it is the Basic Settings screen.
If the wireless router is connected to the Internet, you can select Knowledge Base or Documentation under Web Support in the main menu to view support information or the documentation for the wireless router.
1-4 Configuring Basic Connectivity

If you do not click Logout, the wireless router will wait for 5 minutes after no activity before it automatically logs you out.
Using the Select Language drop-down menu, located in the upper right corner of the Router Manager screen, you can display the router manager screens in any of languages shown in Figure 1-5:

Configuring Basic Connectivity 1-5

The language is set to English by default. The default language is always stored in memory. When you select a language other than the default, that language as well as English is stored in memory. The additional language stored is the most recently selected. For example, if you select Deutsch, German and English will be stored. If you next select Chinese, Chinese and English will be stored.
To specify a language to be used on your router manager screens, do the following:
The language you select is then downloaded and displayed in the language selection box, and your screen display will be in the selected language.
connected to the Internet. When the router is not connected to the Internet, you can select one of the stored languages only.
You can manually configure your Internet connection using the Basic Settings screen, or you can allow the Smart Setup Wizard to determine your Internet Service Provider (ISP) configuration.
The Smart Setup Wizard searches your Internet connection for servers and protocols to determine your ISP configuration.
To use the Smart Setup Wizard to assist with configuration or to verify the Internet connection settings:
1-6 Configuring Basic Connectivity

Settings related to your Internet service are specified in the Basic Settings screen. Select Basic Settings under Setup in the main menu.
The content you see in the Basic Settings screen depends on whether your ISP requires that you log in with a user name and password for Internet access.
ISP does not require login

Configuring Basic Connectivity 1-7

– Account Name (might also be called Host Name). The account name is provided to the ISP during a DHCP request from your router. In most cases, this setting is not required, but some ISPs require it for access to ISP services such as mail or news servers.
– Domain Name. The domain name is provided by your router to computers on your LAN when the computers request DHCP settings from your router. In most cases, this settings is not required.
– Domain Name Server (DNS) Address. If you know that your ISP does not automatically transmit DNS addresses to the router during login, select Use These DNS Servers, and enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it also.
network so that these settings take effect.
– Router MAC Address. This section determines the Ethernet MAC address that the router will use on the Internet port. Typically, you would leave Use Default Address selected. However, some ISPs (especially cable modem providers) register the Ethernet MAC address of the network interface card in your computer when your account is first opened. They then accept only traffic from the MAC address of that computer. This feature allows your router to masquerade as that computer by “cloning” or “spoofing” its MAC address.
To change the MAC address, select one of the following methods:
1-8 Configuring Basic Connectivity

If a login is required by your ISP, the following settings appear in the Basic Settings screen:
ISP does require login

ISP’s login program on your computer to access the Internet. When you start an Internet application, your router will automatically log you in.
– Internet Service Provider. This drop-down list contains a few ISPs that need special protocols for connection. The list includes:
Configuring Basic Connectivity 1-9

accounts still requiring a Bigpond login utility. Telstra has discontinued this type of account. Those with Telstra DSL accounts and newer cable modem accounts should select No for Does Your Internet Connection Require a Login.

requirements.
– Login and Password. This is the user name and password provided by your ISP. This name and password are used to log in to the ISP server.
– Service Name. If your connection is capable of connecting to multiple Internet services, this setting specifies which service to use.

1-10 Configuring Basic Connectivity

– The list includes:
– Idle Timeout. Your Internet connection is logged out if there is no data transfer during the specified time interval.
– Domain Name Server (DNS) Address. If you know that your ISP does not automatically transmit DNS addresses to the router during login, select Use These DNS Servers, and enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it also.
network so that these settings take effect.
disconnected when you click Apply. Reconfigure your wireless adapter to match the new settings, or access the router from a wired computer to make any further changes.
Follow these instructions to set up and test basic wireless connectivity. Once you have established basic wireless connectivity, you can enable security settings appropriate to your needs.
Configuring Basic Connectivity 1-11


SSID of any wireless access adapters must match the SSID you specify in the WNR2000 router. If they do not match, you will not get a wireless connection to the WNR2000 router.
This field determines which operating frequency is used. It should not be necessary to change the wireless channel unless you notice interference problems with another nearby wireless router or access point. Select a channel that is not being used by any other wireless networks within several hundred feet of your router. For more information about the wireless channel frequencies, click the link to the online document “Wireless Networking Basics” in Appendix B.
1-12 Configuring Basic Connectivity

router’s SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change the wireless settings of your computer to match the router’s new settings.

Program the wireless adapter of your computer to have the same SSID and channel that you specified in the router, and disable encryption. Check that your computer has a wireless link and can obtain an IP address by DHCP from the router.
Configuring Basic Connectivity 1-13

Once your computer has basic wireless connectivity to the router, you can configure the advanced wireless security functions of the computer and router (for more information about security and these settings, see Chapter 2, “Safeguarding Your Network ”).
1-14 Configuring Basic Connectivity

The Wireless-N 300 Router Model WNR2000 provides highly effective security features, which are covered in detail in this chapter.
Unlike wired networks, wireless networks allow anyone with a compatible adapter to receive your wireless data transmissions well beyond your walls. Operating an unsecured wireless network creates an opportunity for outsiders to eavesdrop on your network traffic or to enter your network to access your computers and files. Indoors, computers can connect over 802.11g/n wireless networks at ranges of up to 300 feet. Such distances can allow for others outside your immediate area to access your network. Use the security features of your wireless equipment that are appropriate to your needs.
The time it takes to establish a wireless connection can vary depending on both your security settings and router placement.
Stronger security methods can entail a cost in terms of throughput, latency, battery consumption, and equipment compatibility. In choosing an appropriate security level, you can also consider the effort compared to the reward for a hacker to break into your network. As a minimum, however, NETGEAR recommends using WEP with Shared Key authentication. Do not run an unsecured wireless network unless it is your intention to provide free Internet access for the public.

WEP connections can take slightly longer to establish. Also, WEP, WPA-PSK, and WPA2-PSK encryption can consume more battery power on a notebook computer, and can cause significant performance degradation with a slow computer.
router. Default passwords are well known, and an intruder can use your administrator access to read or disable your security settings. For information about how to change the administrator password, see “Changing the Administrator Password” on page 2-21.

Wireless data security options
To configure the wireless network, you can:
– Wireless Settings. You access these under Setup in the main menu (see “Viewing Basic Wireless Settings” on page 2-6).
– Advanced Wireless Settings. You access these under Advanced in the main menu (see “Viewing Advanced Wireless Settings” on page 2-12).
2-2 Safeguarding Your Network

Basic security options are listed in order of increasing effectiveness in Table 2-1. Other features that affect security are listed in Table 2-2 on page 2-4. For more details on wireless security methods, click the link to the online document “Wireless Networking Basics” in Appendix B.
Table 2-1. Wireless Security Options
None. No wireless security. Recommended only for troubleshooting wireless connectivity. Do not run an unsecured wireless network unless it is your intention to provide free Internet access for the public.
WEP. Wired Equivalent Privacy. Wired Equivalent Privacy (WEP) data encryption provides moderate data security. WEP Shared Key authentication and WEP data encryption can be defeated by a determined eavesdropper using publicly available tools. For more information, see “Configuring WEP Wireless Security” on page 2-9.
WPA-PSK (TKIP). WPA-PSK standard encryption with TKIP encryption type.
Wi-Fi Protected Access with Pre-Shared Key (WPA- PSK and WPA2-PSK) data encryption provides extremely strong data security, very effectively blocking eavesdropping. Because WPA and WPA2 are relatively new standards, older wireless adapters and devices might not support them. For more information, see “Configuring WPA-PSK and WPA2-PSK Wireless Security” on page 2-10.
WPA2-PSK (AES). Wi-Fi Protected Access version 2 with Pre-Shared Key; WPA2-PSK standard encryption with the AES encryption type.
WPA-PSK (TKIP) + WPA2-PSK (AES). Mixed mode.
Safeguarding Your Network 2-3
Security Type Description

Table 2-2. Other Features That Enhance Security
Disable the wireless router radio. If you disable the wireless router radio, wireless devices cannot communicate with the router at all. You might disable this when you are away or when other users of your network all use wired connections. For more information, see “Viewing Advanced Wireless Settings” on page 2-12.
Turn off the broadcast of the wireless network name SSID.
If you disable the broadcast of the SSID, only devices that know the correct SSID can connect. This nullifies the wireless network discovery feature of some products such as Windows XP, but your data is still fully exposed to an intruder using available wireless eavesdropping tools. For more information, see “Viewing Advanced Wireless Settings” on page 2-12.
Restrict access based on MAC address. You can restrict access to only trusted computers so that unknown computers cannot wirelessly connect to the WNR2000 router. MAC address filtering adds an obstacle against unwanted access to your network by the general public, but the data broadcast over the wireless link is fully exposed. This data includes your trusted MAC addresses, which can be read and impersonated by a hacker. For more information, see “Restricting Wireless Access by MAC Address” on page 2-19.
Modify your firewall’s rules. By default, the firewall allows any outbound traffic and prohibits any inbound traffic except for responses to your outbound traffic. However, you can modify the firewall’s rules. For more information, see “Understanding Your Firewall” on page 2-23.
Use the Push 'N' Connect feature (Wi-Fi Protected Setup).
Wi-Fi Protected Setup provides easy setup by means of a push button. Older wireless adapters and devices might not support this. Check whether devices are WPS enabled. For more information, see “Using Push 'N' Connect (Wi-Fi Protected Setup)” on page 2-13.
2-4 Safeguarding Your Network
Security Type Description

Before and after customizing your wireless settings, print this section, and record the following information. If you are working with an existing wireless network, the person who set up or is responsible for the network can provide this information. Otherwise, you must choose the settings for your wireless network. Either way, record the settings for your wireless network in the spaces provided.
unless they are also set to Shared Key and are configured with the correct key.
– WEP Encryption Key Size. Choose one: 64-bit or 128-bit. Again, the encryption key size must be the same for the wireless adapters and the wireless router.
Safeguarding Your Network 2-5

– Passphrase These characters are case-sensitive. Enter a word or group of printable characters. When you use WPA-PSK, the other devices in the network will not connect unless they are also set to WPA-PSK and are configured with the correct passphrase. Similarly, when you use WPA2-PSK, the other devices in the network will not connect unless they are also set to WPA2-PSK and are configured with the correct passphrase.
Use the procedures described in the following sections to specify the WNR2000 router. Store this information in a safe place.
This section describes the wireless settings that you can view and configure in the Wireless Settings screen, which you access under Setup in the main menu.
To specify the wireless security settings of your router:
2-6 Safeguarding Your Network

The available settings in this screen are:
Safeguarding Your Network 2-7

– Up To 54 Mbps. Legacy mode, for compatibility with the slower 802.11b and 802.11g wireless devices.
– Up To 145 Mbps. Neighbor Friendly mode, for reduced interference with neighboring wireless networks. Provides two transmission streams with different data on the same channel at the same time, but also allows 802.11b and 802.11g wireless devices. This is the default mode.
– Up To 300 Mbps. Performance mode, using channel expansion to achieve the 300 Mbps data rate. The WNR2000 router will use the channel you selected as the primary channel and expand to the secondary channel (primary channel +4 or –4) to achieve a 40 MHz frame-by-frame bandwidth. The WNR2000 router will detect channel usage and will disable frame-by-frame expansion if the expansion would result in interference with the data transmission of other access points or clients.
specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.
WEP connections can take slightly longer to establish. Also, WEP, WPA-PSK, and WPA2- PSK encryption can consume more battery power on a notebook computer, and can cause significant performance degradation with a slow computer. Instructions for configuring the security options can be found in “Choosing Appropriate Wireless Security” on page 2-1. A full explanation of wireless security standards is available in the online document that you can access from “Wireless Networking Basics” in Appendix B.
2-8 Safeguarding Your Network

WEP Shared Key authentication and WEP data encryption can be defeated by a determined eavesdropper using publicly available tools.
WEP offers the following options:
To configure WEP data encryption:
when you click Apply. You must then either configure your wireless adapter to match the wireless router WEP settings or access the wireless router from a wired computer to make any further changes. Not all wireless adapter configuration utilities support passphrase key generation.
Safeguarding Your Network 2-9


Wi-Fi Protected Access with Pre-Shared Key (WPA-PSK and WPA2-PSK) data encryption provides extremely strong data security, very effectively blocking eavesdropping. Because WPA and WPA2 are relatively new standards, older wireless adapters and devices might not support them. Check whether newer drivers are available from the manufacturer. Also, you might be able to use the Push 'N' Connect feature to configure this type of security if it is supported by your wireless clients. See “Using Push 'N' Connect (Wi-Fi Protected Setup)” on page 2-13.
2-10 Safeguarding Your Network

WPA–Pre-Shared Key does perform authentication. WPA-PSK uses TKIP (Temporal Key Integrity Protocol) data encryption, and WPA2-PSK uses AES (Advanced Encryption Standard) data encryption. Both methods dynamically change the encryption keys making them nearly impossible to circumvent.
Mixed mode allows clients using either WPA-PSK (TKIP) or WPA2-PSK (AES). This provides the most reliable security, and is easiest to implement, but it might not be compatible with older adapters.
required. Windows XP with Service Pack 2 does include WPA support. Nevertheless, the wireless adapter hardware and driver must also support WPA. For instructions on configuring wireless computers or PDAs (personal digital assistants) for WPA-PSK security, consult the documentation for the product you are using.
To configure WPA-PSK, WPA2-PSK, or WPA-PSK+WPA2-PSK:

Safeguarding Your Network 2-11

This section describes the wireless settings that you can view and specify in the Advanced Wireless Settings screen, which you access under Advanced in the main menu.
To configure the advanced wireless security settings of your router:
The available settings in this screen are:
2-12 Safeguarding Your Network

If your wireless clients support Wi-Fi Protected Setup (WPS), you can use this feature to configure the router’s network name (SSID) and security settings and, at the same time, connect a wireless client securely and easily to the router. Look for the symbol on your client device. WPS automatically configures the network name (SSID) and wireless security settings for the router (if the router is in its default state) and broadcasts these settings to the wireless client.
(WPS) standard (for more information, see http://www.wi-fi.org). All other Wi-Fi- certified and WPS-capable products should be compatible with NETGEAR products that implement Push 'N' Connect.
When you add wireless clients, whether or not they are WPS enabled, the added devices must share the same network name (SSID) and security passphrase. For more information, see “Connecting Additional Wireless Client Devices after WPS Setup” on page 2-18.
WPA2-PSK. WEP security is not supported by WPS.
The WNR2000 router provides two methods for connecting to a wireless client that supports WPS, described in the following sections:
Safeguarding Your Network 2-13

There are two methods to enable a wireless client to join a network using a push button on the router: using the physical push button or using the software button in the Add WPS Client screen.
Using the Physical Push Button
The green button light begins to blink in a regular pattern. While the light is blinking, you have 2 minutes to enable WPS on the client that you are trying to connect to the router.
The WNR2000 router’s green button light ceases blinking and remains on when one of these conditions occurs:
Using the Software Button in the Add WPS Client Screen

2-14 Safeguarding Your Network


The green button light on the WNR2000 router begins to blink in a regular pattern. While the button light is blinking, you have 2 minutes to enable WPS on the device you are trying to connect to the router.
The WNR2000 router’s green button light ceases blinking and remains on when one of these conditions occurs:
There are two ways to enable a wireless client to join a network using a PIN: using the router’s security PIN or using the wireless client’s security PIN.
Using the Router’s Security PIN
Using the Wireless Client’s Security PIN
Safeguarding Your Network 2-15



2-16 Safeguarding Your Network


These options are available under WPS Settings:
Safeguarding Your Network 2-17

You can add WPS-enabled and non-WPS-enabled client devices.
Adding Additional WPS-Enabled Clients
To add an additional wireless client device that is WPS enabled:
client unless you have cleared the Keep Existing Wireless Settings check box (in the Wireless Settings screen). If you do clear the check box, a new SSID and a passphrase are generated, and all existing connected wireless clients are disassociated and disconnected from the router.
Adding Additional Non-WPS-Enabled Clients
If you are connecting a combination of WPS-enabled clients and clients that are not WPS enabled, you cannot use the WPS setup procedures to add clients that are not WPS enabled.
To connect both non-WPS-enabled and WPS-enabled clients to the WNR2000 router:
When you change security settings, all existing connected wireless clients that do not share those settings are disassociated and disconnected from the router.
The WNR2000 router automatically preserves the settings you configured in step 1 so all clients share the same security settings (for more information, see “Configuring the WPS Settings” on page 2-17).
2-18 Safeguarding Your Network

When a Wireless Card Access List is configured and enabled, the router checks the MAC address of any wireless device attempting a connection and allows only connections to computers identified on the trusted computers list.
The Wireless Card Access List displays a list of wireless computers that you allow to connect to the router based on their MAC addresses. These wireless computers must also have the correct SSID and wireless security settings to access the wireless router.
The MAC address is a network device’s unique 12-character physical address, containing the hexadecimal characters 0–9, a–f, or A–F only, and separated by colons (for example, 00:09:AB:CD:EF:01). It can usually be found on the bottom of the wireless card or network interface device. If you do not have access to the physical label, you can display the MAC address using the network configuration utilities of the computer. In WindowsXP, for example, typing the ipconfig/all command in an MSDOS command prompt window displays the MAC address as Physical Address. You might also find the MAC addresses in the router’s Attached Devices screen.
To restrict access based on MAC addresses:

Safeguarding Your Network 2-19


screen into the MAC Address field of this screen. To do this, configure each wireless computer to obtain a wireless link to the router. The computer should then appear in the Attached Devices screen.
2-20 Safeguarding Your Network

not in the Trusted PC list, if you select Turn Access Control On, you lose your wireless connection when you click Apply. You must then access the wireless router from a wired computer or from a wireless computer that is on the access control list to make any further changes.
Now, only devices on this list can wirelessly connect to the WNR2000 router.
network by the general public. However, because your trusted MAC addresses appear in your wireless transmissions, an intruder can read them and impersonate them. Do not rely on MAC address filtering alone to secure your network.
The default password for the router’s Web Configuration Manager is password. NETGEAR recommends that you change this password to a more secure password.
default password of password. If you save the settings with a new password, and then you later forget the new password, you will have to reset the router back to the factory defaults, and log in using the default password of password. This means you will have to re-enter all the router configuration settings. For information about how to back up your settings, see “Backing Up and Restoring the Configuration” on page 6-8.
Safeguarding Your Network 2-21

To change the administrator password:

The configuration settings of the WNR2000 router are stored within the router in a configuration file. You can back up (save) this file and retrieve it later. NETGEAR recommends that you save your configuration file after you complete the configuration. If the router fails or becomes corrupted, or an administrator password is lost, you can easily re-create your configuration by restoring the configuration file.
For instructions on saving and restoring your configuration file, see “Managing the Configuration File” on page 6-7.
default, password. Then change it again after you have saved the configuration file. If you save the file with a new password, and then you later forget the new password, you will have to reset the router back to the factory defaults and log in using the default password of password. This means you will have to re-enter all the router configuration settings.
2-22 Safeguarding Your Network

Your Wireless-N 300 Router Model WNR2000 contains a true firewall to protect your network from attacks and intrusions. A firewall is a device that protects one network from another while allowing communication between the two. Using a process called Stateful Packet Inspection, the firewall analyzes all inbound and outbound traffic to determine whether or not it will be allowed to pass through.
By default, the firewall allows any outbound traffic and prohibits any inbound traffic except for responses to your outbound traffic. However, you can modify the firewall’s rules to achieve the following behavior:
Safeguarding Your Network 2-23

2-24 Safeguarding Your Network

This chapter describes how to use the content filtering and reporting features of the Wireless-N 300 Router Model WNR2000 to protect your network.
The Wireless-N 300 Router Model WNR2000 provides you with Web content filtering options, plus browser activity reporting and instant alerts through e-mail. Parents and network administrators can establish restricted access policies based on time of day, Web addresses, and Web address keywords. You can also block Internet access by applications and services, such as chat rooms or games.
The WNR2000 router allows you to restrict access based on Web addresses and Web address keywords. Up to 255 entries are supported in the Keyword list.
Keyword application examples:

To block access to Internet sites:

To block by schedule, be sure to specify a time period in the Schedule screen. For information about scheduling, see “Scheduling Blocking” on page 3-5.
Block all access to Internet browsing during a scheduled period by entering a dot (.) as the keyword, and then set a schedule in the Schedule screen.
Delete a keyword or domain name by selecting it from the list and clicking Delete Keyword.
3-2 Restricting Access From Your Network

Since the trusted user is identified by IP address, you should configure that computer with a fixed IP address.
The WNR2000 router allows you to block the use of certain Internet services by computers on your network. This is called service blocking or port filtering. Services are functions performed by server computers at the request of client computers. For example, Web servers serve Web pages, time servers serve time and date information, and game hosts serve data about other players’ moves. When a computer on your network sends a request for service to a server computer on the Internet, the requested service is identified by a service or port number. This number appears as the destination port number in the transmitted IP packets. For example, a packet that is sent with destination port number 80 is an HTTP (Web server) request.
To block access to Internet services:

To block by schedule, be sure to specify a time period in the Schedule screen. For information about scheduling, see “Scheduling Blocking” on page 3-5.
Restricting Access From Your Network 3-3


4. From the Service Type list, select the application or service to be allowed or blocked. The list already displays several common services, but you are not limited to these choices. To add any additional services or applications that do not already appear, select User Defined. To define a service, first you must determine which port number or range of numbers is used by the application. The service port numbers for many common protocols are defined by the Internet Engineering Task Force (IETF) and published in RFC1700, “Assigned Numbers.” Service numbers for other applications are typically chosen from the range 1024 to 65535 by the authors of the application. You can often determine port number information by contacting the publisher of the application, by asking user groups or newsgroups, or by searching.
– Enter the starting port and ending port numbers. If the application uses a single port number, enter that number in both fields.
– If you know that the application uses either TCP or UDP, select the appropriate protocol. If you are not sure, select Both.
3-4 Restricting Access From Your Network

In the Filter Services For area, you can block the specified service for a single computer, a range of computers (having consecutive IP addresses), or all computers on your network.
The WNR2000 router allows you to specify when blocking is enforced.
To schedule blocking:

a. Days to Block. Select days on which you want to apply blocking by selecting the appropriate check boxes. Select Every Day to select the check boxes for all days. Click Apply.
b. Time of Day to Block. Select a start and end time in 24-hour format. Select All Day for 24-hour blocking. Click Apply.
Restricting Access From Your Network 3-5

Be sure to select your time zone in the E-mail screen as described in “Setting the Time Zone” on page 3-9.
The log is a detailed record of the websites you have accessed or attempted to access. Up to 128 entries are stored in the log. Log entries appear only when keyword blocking is enabled and no log entries are made for the trusted user.
Select Logs under Content Filtering in the main menu. The Logs screen displays.

Table 3-1 describes the log entries.
Table 3-1. Log Entry Descriptions
Date and time The date and time the log entry was recorded.
Source IP The IP address of the initiating device for this log entry.
3-6 Restricting Access From Your Network
Field Description

Table 3-1. Log Entry Descriptions
Target address The name or IP address of the website or newsgroup visited or to which access was attempted.
Action Whether the access was blocked or allowed.
To refresh the log screen, click the Refresh button.
To clear the log entries, click the Clear Log button.
To e-mail the log immediately, click the Send Log button.
To receive logs and alerts by e-mail, you must provide your e-mail account information.
To configure e-mail alert and web access log notifications:
Restricting Access From Your Network 3-7
Field Description


a. Enter the name of your ISP’s outgoing (SMTP) mail server (such as mail.myISP.com) in the Your Outgoing Mail Server field. You might be able to find this information in the configuration screen of your e-mail program. If you leave this field blank, log and alert messages will not be sent by e-mail.
b. Enter the e-mail address to which logs and alerts are sent in the Send To This E-mail Address field. This e-mail address will also be used as the From address. If you leave this field blank, log and alert messages will not be sent by e-mail.
a. Enter your user name for the e-mail server in the User Name field.
3-8 Restricting Access From Your Network

b. Enter your password for the e-mail server in the Password field.
– Day. Specifies which day of the week to send the log. Relevant when the log is sent weekly or daily.
– Time. Specifies the time of day to send the log. Relevant when the log is sent daily or weekly.
If you select the Weekly, Daily, or Hourly option and the log fills up before the specified period, the log is automatically e-mailed to the specified e-mail address. After the log is sent, the log is cleared from the router’s memory. If the router cannot e-mail the log file, the log buffer might fill up. In this case, the router overwrites the log and discards its contents.
So that the log entries are correctly time-stamped and sent at the correct time, be sure to set the time as described in the next section.
The WNR2000 router uses the Network Time Protocol (NTP) to obtain the current time and date from one of several network time servers on the Internet. Localize the time zone so that your log entries and other router functions include the correct time stamp.
To verify and set the time zone (see Figure 3-6 on page 3-8):
Restricting Access From Your Network 3-9

3-10 Restricting Access From Your Network

This chapter describes how to configure advanced networking features of the Wireless-N 300 Router Model WNR2000, including LAN, WAN, and routing settings.
The LAN Setup screen allows configuration of LAN IP services such as Dynamic Host Configuration Protocol (DHCP) and Routing Information Protocol (RIP).

To configure LAN IP settings, select LAN Setup under Advanced in the main menu. The LAN Setup screen displays.

The device name is a user-friendly name for the router. This name is shown in the Network on Windows Vista and the Network Explorer on all Windows systems. The Device Name field cannot be blank. The default name is WNR2000.
4-2 Customizing Your Network Settings

These are advanced settings that you might configure if you are a network administrator and your network contains multiple routers. The router is shipped preconfigured to use private IP addresses on the LAN side and to act as a DHCP server (see “Using the Router as a DHCP Server” on page 4-4).
browser, you will be disconnected. You must then open a new connection to the new IP address and log in again.
The router’s default LAN IP configuration is:
These addresses are part of the designated private address range for use in private networks and should be suitable for most applications. If your network has a requirement to use a different IP addressing scheme, you can make those changes in this screen.
The LAN IP settings are:
– When set to Both or In Only, the router incorporates the RIP information that it receives.
– When set to Both or Out Only, the router broadcasts its routing table periodically.
– RIP-1 is universally supported. RIP-1 is usually adequate unless you have an unusual network setup.
– RIP-2B carries more information than RIP-1 and uses subnet broadcasting.
– RIP-2M carries more information than RIP-1 and uses multicasting.
Customizing Your Network Settings 4-3

By default, the router functions as a DHCP server, allowing it to assign IP, DNS server, and default gateway addresses to all computers connected to the router’s LAN. The assigned default gateway address is the LAN address of the router. The router assigns IP addresses to the attached computers from a pool of addresses specified in this screen. Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN.
satisfactory. Click the link to the online document “TCP/IP Networking Basics” in Appendix B for an explanation of DHCP and information about how to assign IP addresses for your network.
To specify a pool of IP addresses to be assigned, set the starting IP address and ending IP address. These addresses should be part of the same IP address subnet as the router’s LAN IP address. Using the default addressing scheme, you should define a range between 192.168.1.2 and 192.168.1.254, although you might wish to save part of the range for devices with fixed addresses.
The router delivers the following parameters to any LAN device that requests DHCP:
To use another device on your network as the DHCP server, or to manually specify the network settings of all of your computers, clear the Use Router as DHCP Server check box. Otherwise, leave it selected. If this service is not selected and no other DHCP server is available on your network, you need to set your computers’ IP addresses manually or they will not be able to access the router.
4-4 Customizing Your Network Settings

When you specify a reserved IP address for a computer on the LAN, that computer always receives the same IP address each time it accesses the router’s DHCP server. Reserved IP addresses should be assigned to computers or servers that require permanent IP settings.

To reserve an IP address:
address from the Attached Devices screen and paste it here.
the router’s DHCP server. Reboot the computer or access its IP configuration and force a DHCP release and renew.
To edit or delete a reserved address entry:
Customizing Your Network Settings 4-5

If your Internet Service Provider (ISP) gave you a permanently assigned IP address, you can register a domain name and have that name linked with your IP address by public Domain Name Servers (DNS). However, if your Internet account uses a dynamically assigned IP address, you do not know in advance what your IP address will be, and the address can change frequently. In this case, you can use a commercial Dynamic DNS service, which allows you to register your domain to their IP address, and forwards traffic directed at your domain to your frequently changing IP address.
Dynamic DNS service will not work because private addresses are not routed on the Internet.
Your router contains a client that can connect to the Dynamic DNS service provided by DynDNS.org. You must first visit their website at www.dyndns.org and obtain an account and host name, which you specify in the router. Then, whenever your ISP-assigned IP address changes, your router automatically contacts the Dynamic DNS service provider, logs in to your account, and registers your new IP address. If your host name is hostname, for example, you can reach your router at hostname.dyndns.org.
Select Dynamic DNS under Advanced in the main menu. The Dynamic DNS screen displays.

4-6 Customizing Your Network Settings

To configure for a Dynamic DNS service:
Customizing Your Network Settings 4-7

The WAN Setup options let you configure a DMZ (demilitarized zone) server, change the Maximum Transmit Unit (MTU) size, and enable the wireless router to respond to a ping on the WAN (Internet) port. Select WAN Setup under Advanced in the main menu. The WAN Setup screen displays.

The Stateful Packet Inspection (SPI) firewall protects your network and computers against attacks and intrusions. A stateful packet firewall carefully inspects incoming traffic packets, looking for known exploits such as malformed, oversized, or out-of-sequence packets. The firewall should be disabled only in special circumstances, such as when you are troubleshooting application issues.
The default DMZ server feature is helpful when you are using some online games and videoconferencing applications that are incompatible with Network Address Translation (NAT). The router is programmed to recognize some of these applications and to work correctly with
4-8 Customizing Your Network Settings

them, but there are other applications that might not function well. In some cases, one local computer can run the application correctly if that computer’s IP address is entered as the default DMZ server.
server loses much of the protection of the firewall, and is exposed to exploits from the Internet. If compromised, the DMZ server computer can be used to attack other computers on your network.
Incoming traffic from the Internet is usually discarded by the router unless the traffic is a response to one of your local computers or a service that you have configured in the Port Forwarding/Port Triggering screen. Instead of discarding this traffic, you can have it forwarded to one computer on your network. This computer is called the default DMZ server.
The WAN Setup screen lets you configure a default DMZ server.
To assign a computer or server to be a default DMZ server:
If you want the router to respond to a ping from the Internet, select the Respond to Ping on Internet Port check box. This should be used only as a diagnostic tool, since it allows your router to be discovered by Internet scanners. Do not select this check box unless you have a specific reason to do so, such as when troubleshooting your connection.
The normal MTU value for most Ethernet networks is 1500 bytes, 1492 bytes for PPPoE connections, or 1450 for PPTP connections. For some ISPs, you might need to reduce the MTU size, but this is rarely required and should not be done unless you are sure it is necessary for your ISP connection. For more information, see “Changing the MTU Size” on page 5-16.
To change the MTU size:
Customizing Your Network Settings 4-9

Network Address Translation (NAT) determines how the router processes inbound traffic. Secured NAT provides a secured firewall to protect the computers on the LAN from attacks from the Internet, but might prevent some Internet games, point-to-point applications, or multimedia applications from functioning. Open NAT provides a much less secured firewall, but allows almost all Internet applications to function. For more information about NAT, see “How Your Computer Accesses a Remote Computer through Your Router” on page 5-2.
To change the NAT option:
Static routes provide additional routing information to your router. Under usual circumstances, the router has adequate routing information after it has been configured for Internet access, and you do not need to configure additional static routes. You must configure static routes only for unusual cases such as multiple routers or multiple IP subnets located on your network.
As an example of when a static route is needed, consider the following case:
When you first configured your router, two implicit static routes were created. A default route was created with your ISP as the gateway, and a second static route was created to your local network for all 192.168.1.x addresses. With this configuration, if you attempt to access a device on the 134.177.0.0 network, your router forwards your request to the ISP. The ISP forwards your request to the company where you are employed, and the request is likely to be denied by the company’s firewall.
In this case you must define a static route, telling your router that 134.177.0.0 should be accessed through the ISDN router at 192.168.1.100.
In this example:
4-10 Customizing Your Network Settings

To add or edit a static route:


Customizing Your Network Settings 4-11

This represents the number of routers between your network and the destination. Usually, a setting of 2 or 3 works, but if this is a direct connection, set it to 1.
The WNR2000 router can be used with a wireless access point (AP) to build large bridged wireless networks. Wireless repeating is a type of Wireless Distribution System (WDS).
are limited to None or WEP. For more information about wireless security, see Chapter 2, “Safeguarding Your Network.”
The following figure shows a wireless repeating scenario:

4-12 Customizing Your Network Settings
Repeater AP · Base Station AP

To set up a wireless network using WDS, the following conditions must be met for both APs:
You can view or change wireless repeater settings for the wireless router. From the main menu of the browser interface, under Advanced, click Wireless Repeating Function to display the Wireless Repeating Function screen.

The wireless router supports two modes of the wireless repeating function, and allows you to control wireless client association:
Customizing Your Network Settings 4-13

If this check box is selected, the router communicates wirelessly only with other APs whose MAC addresses are listed in this screen. The router still communicates with wire-connected LAN devices.
The wireless repeating function works only in hub and spoke mode. The units cannot be daisy chained. You must know the wireless settings for both units. You must know the MAC address of the remote unit. First, set up the base station, and then set up the repeater.
To set up the base station:
4-14 Customizing Your Network Settings

Use a wired Ethernet connection to set up the repeater unit to avoid conflicts with the wireless connection to the base station.
as the repeater, you might need to change additional configuration settings. In particular, you should disable the DHCP server function on the wireless repeater AP.
To configure a WNR2000 router as a repeater unit:
network because the factory default LAN IP is the same for both units.
A computer on any wireless or wired LAN segment of the wireless router should be able to connect to the Internet or share files and printers with any other wireless or wired computer or server connected to the other AP.
Customizing Your Network Settings 4-15

4-16 Customizing Your Network Settings

This chapter describes how to modify the configuration of the Wireless-N 300 Router Model WNR2000 to allow specific applications to access the Internet or to be accessed from the Internet, and how to make adjustments to enhance your network’s performance.
Your router provides two features for creating these exceptions: port forwarding and port triggering. This section explains how a normal outbound connection works, followed by two examples explaining how port forwarding and port triggering operate and how they differ.

When a computer on your network needs to access a computer on the Internet, your computer sends your router a message containing source and destination address and process information. Before forwarding your message to the remote computer, your router must modify the source information and must create and track the communication session so that replies can be routed back to your computer.
Here is an example of normal outbound traffic and the resulting inbound responses:
Your computer then sends this request message to your router.
Your router then sends this request message through the Internet to the Web server at www.example.com
5-2 Fine-Tuning Your Network

The Web server then sends this reply message to your router.
Your router then sends this reply message to your computer, which displays the Web page from www.example.com
In the preceding example, requests are sent to a remote computer by your router from a particular service port number, and replies from the remote computer to your router are directed to that port number. If the remote server sends a reply back to a different port number, your router will not recognize it and will discard it. However, some application servers (such as FTP and IRC servers) send replies back to multiple port numbers. Using the port triggering function of your router, you can tell the router to open additional incoming ports when a particular outgoing port originates a session.
An example is Internet Relay Chat (IRC). Your computer connects to an IRC server at destination port 6667. The IRC server not only responds to your originating source port, but also sends an “identify” message to your computer on port 113. Using port triggering, you can tell the router,
Fine-Tuning Your Network 5-3

“When you initiate a session with destination port 6667, you must also allow incoming traffic on port 113 to reach the originating computer.” Using steps similar to the preceding example, the following sequence shows the effects of the port triggering rule you have defined:
To configure port triggering, you need to know which inbound ports the application needs. Also, you need to know the number of the outbound port that will trigger the opening of the inbound ports. You can usually determine this information by contacting the publisher of the application, or user groups or newsgroups.
5-4 Fine-Tuning Your Network

In both of the preceding examples, your computer initiates an application session with a server computer on the Internet. However, you might need to allow a client computer on the Internet to initiate a connection to a server computer on your network. Normally, your router ignores any inbound traffic that is not a response to your own outbound traffic. You can configure exceptions to this default rule by using the port forwarding feature.
A typical application of port forwarding can be shown by reversing the client-server relationship from our previous Web server example. In this case, a remote computer’s browser needs to access a Web server running on a computer in your local network. Using port forwarding, you can tell the router, “When you receive incoming traffic on port 80 (the standard port number for a Web server process), forward it to the local computer at 192.168.1.123.” The following sequence shows the effects of the port forwarding rule you have defined:
The remote computer then sends this request message through the Internet to your router.
The destination address is replaced with 192.168.1.123.
Your router then sends this request message to your local network.
To configure port forwarding, you need to know which inbound ports the application needs. You usually can determine this information by contacting the publisher of the application or user groups or newsgroups.
Fine-Tuning Your Network 5-5

Using the port forwarding feature, you can allow certain types of incoming traffic to reach servers on your local network. For example, you might make a local Web server, FTP server, or game server visible and available to the Internet.
Use the Port Forwarding screen to configure the router to forward specific incoming protocols to computers on your local network. In addition to servers for specific applications, you can also specify a default DMZ server to which all other incoming protocols are forwarded. The DMZ server is configured in the WAN Setup screen, as discussed in “Setting Up a Default DMZ Server” on page 4-8.
Before starting, you need to determine which type of service, application, or game you will provide, and the local IP address of the computer that will provide the service. Be sure the computer’s IP address never changes.
reserved IP address feature of your WNR2000 router. See “Using Address Reservation” on page 4-5 for instructions on how to use reserved IP addresses.
5-6 Fine-Tuning Your Network

To configure port forwarding to a local server:

To define a service, game, or application that does not appear in the Service Name list, you must first determine which port number or range of numbers is used by the application. You can usually determine this information by contacting the publisher of the application or user groups or newsgroups. When you have the port number information, follow these steps:
Fine-Tuning Your Network 5-7


5-8 Fine-Tuning Your Network

To edit or delete a port forwarding entry:

If you host a Web server on your local network, you can use port forwarding to allow Web requests from anyone on the Internet to reach your Web server.
To make a local Web server public:
Fine-Tuning Your Network 5-9

When port triggering is enabled, the router monitors outbound traffic looking for a specified outbound “trigger” port. When the router detects outbound traffic on that port, it remembers the IP address of the local computer that sent the data. The router then temporarily opens the specified incoming port or ports, and forwards incoming traffic on the triggered ports to the triggering computer.
While port forwarding creates a static mapping of a port number or range to a single local computer, port triggering can dynamically open ports to any computer that needs them and can close the ports when they are no longer needed.
time communications such as instant messaging, or remote assistance (a feature in Windows XP), you should also enable Universal Plug and Play (UPnP) according to the instructions in “Using Universal Plug and Play” on page 5-14.
To configure port triggering, you need to know which inbound ports the application needs. Also, you need to know the number of the outbound port that will trigger the opening of the inbound ports. You can usually determine this information by contacting the publisher of the application or user groups or newsgroups.
To set up port triggering:
5-10 Fine-Tuning Your Network


triggering, port triggering is disabled. However, any port triggering configuration information you added to the router is retained even though it is not used.
Fine-Tuning Your Network 5-11


5-12 Fine-Tuning Your Network


Fine-Tuning Your Network 5-13

Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers, to access the network and connect to other devices as needed. UPnP devices can automatically discover the services from other registered UPnP devices on the network.
time communications such as instant messaging, or remote assistance (a feature in Windows XP), you should enable UPnP.
To turn on Universal Plug and Play:

5-14 Fine-Tuning Your Network

The speed and operating distance or range of your wireless connection can vary significantly based on the physical placement of the wireless router. You should choose a location for your router that will maximize the network speed.
or inability to wirelessly connect to the router. For complete range and performance specifications, click the link to the online document “Wireless Networking Basics” in Appendix B.
The following list describes how to optimize wireless router performance.
Fine-Tuning Your Network 5-15

– Near the center of the area in which your computers will operate.
– In an elevated location such as a high shelf where the wirelessly connected computers have line-of-sight access (even if through walls).
– Avoid obstacles to wireless signals.
– Keep wireless devices at least 2 feet from large metal fixtures such as file cabinets, refrigerators, pipes, metal ceilings, reinforced concrete, and metal partitions.
– Keep away from large amounts of water such as fish tanks and water coolers.
– Avoid windows unless communicating between buildings.
– Place wireless devices away from various electromagnetic noise sources, especially those in the 2400–2500 MHz frequency band. Common noise-creating sources are:
– Use a scanning utility to determine what other wireless networks are operating nearby, and choose an unused channel.
– Turn off SSID broadcast, and change the default SSID. Other nearby devices might automatically try to connect to your network several times a second, which can cause significant performance reduction.
The Maximum Transmission Unit (MTU) is the largest data packet a network device transmits. When one network device communicates across the Internet with another, the data packets travel through many devices along the way. If any device in the data path has a lower MTU setting than the other devices, the data packets must be split or “fragmented” to accommodate the one with the smallest MTU.
5-16 Fine-Tuning Your Network

The best MTU setting for NETGEAR equipment is often just the default value, and changing the value might fix one problem but cause another. Leave MTU unchanged unless one of these situations occurs:
– A secure Web site that will not open, or displays only part of a Web page
– America Online’s DSL service
inability to access certain Web sites, frames within Web sites, secure login pages, or FTP or POP servers.
If you suspect an MTU problem, a common solution is to change the MTU size to 1400. If you are willing to experiment, you can gradually reduce the MTU size from the maximum value of 1500 until the problem goes away. Table 5-1 describes common MTU sizes and applications.
Table 5-1. Common MTU Sizes
1500 The largest Ethernet packet size and the default value. This is the typical setting for non- PPPoE, non-VPN connections, and is the default value for NETGEAR routers, adapters, and switches.
1492 Used in PPPoE environments.
1472 Maximum size to use for pinging. (Larger packets are fragmented.)
1468 Used in some DHCP environments.
1460 Usable by AOL if you do not have large e-mail attachments, for example.
1436 Used in PPTP environments or with VPN.
1400 Maximum size for AOL DSL.
576 Typical value to connect to dial-up ISPs.
Fine-Tuning Your Network 5-17
– Yahoo e-mail · MTU Application

To change the MTU size:
Quality of Service (QoS) is an advanced feature that can be used to prioritize some types of traffic ahead of others. The WNR2000 router can provide QoS prioritization over the wireless link and on the Internet connection.
The WNR2000 router supports Wi-Fi Multimedia Quality of Service (WMM QoS) to prioritize wireless voice and video traffic over the wireless link. WMM QoS provides prioritization of wireless data packets from different applications based on four access categories: voice, video, best effort, and background. For an application to receive the benefits of WMM QoS, both it and the client running that application must be WMM enabled. Legacy applications that do not support WMM, and applications that do not require QoS, are assigned to the best effort category, which receives a lower priority than voice and video.
To specify prioritization of traffic, you must create a policy for the type of traffic and add the policy to the QoS Policy table in the QoS Setup screen.
To create a QoS policy:
5-18 Fine-Tuning Your Network

From the main menu of the browser interface, under Advanced, select QoS Setup. The QoS Setup screen displays:

WMM QoS is enabled by default. You can disable it by clearing the Enable WMM check box and clicking Apply.
QoS for Applications and Online Gaming
To create a QoS policy for traffic for specific applications or online games:
Fine-Tuning Your Network 5-19


For convenience, the QoS Policy table lists many common applications and online games that can benefit from QoS handling.
5-20 Fine-Tuning Your Network


a. If you chose to add a new entry, the screen expands as shown:

b. In the QoS Policy for field, enter a descriptive name for the new application or game.
c. Select the packet type, either TCP, UDP, or both (TCP/UDP), and specify the port number or range of port numbers used by the application or game.
Fine-Tuning Your Network 5-21

QoS for a Router LAN Port
To create a QoS policy for a device connected to one of the router’s LAN ports:

5-22 Fine-Tuning Your Network

QoS for a MAC Address
To create a QoS policy for traffic from a specific MAC address:

Editing or Deleting an Existing QoS Policy
To edit or delete an existing QoS policy:
Fine-Tuning Your Network 5-23

Common connection types and their speed and security considerations are:
To get the best performance, use RangeMax NEXT adapters such as the WN511B for your computers. Although the RangeMax NEXT router is compatible with older 802.11b and 802.11g adapters, the use of these older wireless technologies in your network can result in lower throughput overall (typically less than 10 Mbps for 802.11b and less than 40 Mbps for 802.11g). In addition, many older wireless products do not support the latest security protocols, WPA and WPA2.
5-24 Fine-Tuning Your Network

The Powerline HD family of products can coexist on the same network with older-generation XE family products or HomePlug 1.0 products, but they are not interoperable with these older products.
including volume of network traffic, building materials and construction, and network overhead, can lower actual data throughput rate.
Because your Internet connection is likely to operate at a much lower speed than your local network, faster local networking technologies might not improve your Internet experience. However, many emerging home applications require high data rates. For example:
Fine-Tuning Your Network 5-25

Table 5-2. Theoretical Transfer Time for 1 Gigabyte
Network Connection Theoretical Raw Transfer Time
Gigabit wired Ethernet 8 seconds
RangeMax NEXT Wireless-N 26 seconds
Powerline HD 40 seconds
100 Mbps wired Ethernet 80 seconds
802.11n wireless 45 seconds
802.11g wireless 150 seconds
802.11b wireless 700 seconds
10 Mbps wired Ethernet 800 seconds
Cable modem (3 Mbps) 2700 seconds
Analog modem (56 kbps) 144,000 seconds (40 hours)
5-26 Fine-Tuning Your Network

This chapter describes how to use the maintenance features of your Wireless-N 300 Router Model WNR2000.

To view router status and usage information:

6-2 Using Network Monitoring Tools

Table 6-1 describes the router status fields.
Table 6-1. Wireless Router Status Fields
Hardware Version The hardware version of the router.
Firmware Version The version of the current software installed in the router. This will change if you update your router.
GUI Language Version The version of the selected GUI language for the router manager screens.
Internet Port. The following settings apply to the Internet (WAN) port of the router.
MAC Address The Media Access Control address. This is the unique physical address being used by the Internet (WAN) port of the router.
IP Address The IP address being used by the Internet (WAN) port of the router. If no address is shown, or is 0.0.0.0, the router cannot connect to the Internet.
DHCP If set to None, the router is configured to use a fixed IP address on the WAN. If set to DHCP Client, the router is configured to obtain an IP address dynamically from the ISP.
IP Subnet Mask The IP subnet mask being used by the Internet (WAN) port of the router. For an explanation of subnet masks and subnet addressing, click the link to the online document “TCP/IP Networking Basics” in Appendix B.
Domain Name Server The Domain Name Server addresses being used by the router. A Domain Name Server translates human-language URLs such as www.netgear.com into IP addresses.
LAN Port. The following settings apply to the Ethernet (LAN) port of the router.
MAC Address The Media Access Control address. This is the unique physical address being used by the LAN port of the router.
IP Address The IP address being used by the Ethernet (LAN) port of the router. The default is 192.168.1.1.
DHCP Identifies whether the router’s built-in DHCP server is active for the LAN-attached devices.
IP Subnet Mask The IP subnet mask being used by the Ethernet (LAN) port of the router. The default is 255.255.255.0.
Using Network Monitoring Tools 6-3
Field Description

Table 6-1. Wireless Router Status Fields (continued)
Wireless Port. The following settings apply to the wireless port of the router.
Name (SSID) The wireless network name (SSID) being used by the wireless port of the router. The default is NETGEAR.
Region The geographic region where the router is being used. It might be illegal to use the wireless features of the router in some parts of the world.
Channel Identifies the channel of the wireless port being used. Click the link to the online document “Wireless Networking Basics” in Appendix B for the frequencies used on each channel.
Wireless AP Indicates whether the radio feature of the router is enabled. If not enabled, the Wireless LED on the front panel is off.
Broadcast Name Indicates whether the router is broadcasting its SSID.
Wi-Fi Protected Setup Indicates whether the router’s PIN is enabled and whether the router is configured for Push ‘N’ Connect (Wi-Fi Protected Setup). For more information, see “Using Push 'N' Connect (Wi-Fi Protected Setup)” on page 2-13.
6-4 Using Network Monitoring Tools
Field Description


Table 6-2 describes the connection status settings.
Table 6-2. Connection Status Settings
IP Address The IP address that is assigned to the router.
Subnet Mask The subnet mask that is assigned to the router.
Default Gateway The IP address for the default gateway that the router communicates with.
DHCP Server The IP address for the Dynamic Host Configuration Protocol server that provides the TCP/IP configuration for all the computers that are connected to the router.
DNS Server The IP address of the Domain Name Service server that provides translation of network names to IP addresses.
Lease Obtained The date and time that the lease was obtained.
Lease Expires The date and time that the lease will expire.
a. Click the Release button to release the connection status items (that is, all items return to 0).
b. Click the Renew button to renew to the connection status items (that is, all items are refreshed).
c. Click the Close Window button to close the Connection Status screen.
Using Network Monitoring Tools 6-5
Item Description


Table 6-3 describes the router statistics.
Table 6-3. Router Statistics
System Up Time The time elapsed since the router was last restarted.
Port The statistics for the WAN (Internet) and LAN (Ethernet) ports. For each port, the screen displays the following:
Status The link status of the port.
TxPkts The number of packets transmitted on this port since reset or manual clear.
RxPkts The number of packets received on this port since reset or manual clear.
Collisions The number of collisions on this port since reset or manual clear.
Tx B/s The current transmission (outbound) bandwidth used on the WAN and LAN ports.
Rx B/s The current reception (inbound) bandwidth used on the WAN and LAN ports.
Up Time The time elapsed since this port acquired the link.
Poll Interval The intervals at which the statistics are updated in this screen.
To change the polling frequency, enter a time in seconds in the Poll Interval field, and click Set Interval.
To stop the polling entirely, click Stop.
6-6 Using Network Monitoring Tools
Item Description

The Attached Devices screen contains a table of all IP devices that the router has discovered on the local network. Select Attached Devices under Maintenance in the main menu to view the table.

For each device, the table shows the IP address, NetBIOS host name or device name (if available), and the Ethernet MAC address. To force the router to look for attached devices, click Refresh.
devices.
The configuration settings of the WNR2000 router are stored within the router in a configuration file. You can back up (save) this file to your computer, restore it, or reset it to the factory default settings.
Using Network Monitoring Tools 6-7

Select Backup Settings under Maintenance in the main menu. The Backup Settings screen displays.

The following sections describe the three available options.
The Restore and Backup options in the Settings Backup screen let you save and retrieve a file containing your router’s configuration settings.
To save your settings, click Backup. Your browser extracts the configuration file from the router and prompts you for a location on your computer to store the file. You can give the file a meaningful name at this time, such as comcast.cfg.
default, password. Then change it again after you have saved the configuration file. If you forget the password, you will need to reset the configuration to factory defaults.
To restore your settings from a saved configuration file, enter the full path to the file on your computer, or click Browse to browse to the file. When you have located it, click Restore to send the file to the router. The router then reboots automatically.
6-8 Using Network Monitoring Tools

Under some circumstances (for example, if you move the router to a different network or if you have forgotten the password) you might want to erase the configuration and restore the factory default settings. After an erase, the router’s username is admin, the password is password, the LAN IP address is 192.168.1.1 (or www.routerlogin.net), and the router’s DHCP server is enabled.
To erase the configuration, click the Erase button in the Settings Backup screen.
To restore the factory default configuration settings when you do not know the login password or IP address, you must use the restore factory settings button on the rear panel of the router (see “Restoring the Default Configuration and Password” on page 7-12).
The firmware of the WNR2000 router is stored in flash memory, and can be updated as NETGEAR releases new firmware. You can update your firmware by logging into the router and using one of these procedures:
configuration settings (see “Backing Up and Restoring the Configuration” on page 6-8). A firmware update might cause the router settings to revert to the factory defaults. If this happens, after completing the update, you can restore your settings from the backup.
Using Network Monitoring Tools 6-9

To check for new firmware and allow the router to automatically install it:

6-10 Using Network Monitoring Tools

the Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, it could corrupt the firmware.
When the upload is complete, your router automatically restarts. The update process typically takes about 1 minute.
To manually select, download, and install new software to your router:

Using Network Monitoring Tools 6-11

Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, it could corrupt the firmware.
When the upload is complete, your router automatically restarts. The upgrade process typically takes about 1 minute.
6-12 Using Network Monitoring Tools

Using the Remote Management feature, you can allow a user on the Internet to configure, upgrade, and check the status of your WNR2000 router. Select Remote Management under Advanced in the main menu. The Remote Management screen displays.

password. The ideal password should contain no dictionary words from any language, and should be a mixture of letters (both uppercase and lowercase), numbers, and symbols. Your password can be up to 30 characters.
To configure your router for remote management:
Using Network Monitoring Tools 6-13

as practical.
Normal Web browser access uses the standard HTTP service port 80. For greater security, enter a custom port number for the remote management Web interface. Choose a number between 1024 and 65535, but do not use the number of any common service port. The default is 8080, which is a common alternate for HTTP.
into your browser’s address or location field, followed by a colon (:) and the custom port number. For example, if your external address is 134.177.0.123 and you use port number 8080, then enter http://134.177.0.123:8080 in your browser.
6-14 Using Network Monitoring Tools

Traffic Metering allows you to monitor the volume of Internet traffic passing through your router’s Internet port. With the Traffic Meter utility, you can set limits for traffic volume, set a monthly limit, and get a live update of traffic usage.
To monitor traffic on your router, do the following:

Using Network Monitoring Tools 6-15

6-16 Using Network Monitoring Tools

This chapter provides information about troubleshooting your Wireless-N 300 Router Model WNR2000. After each problem description, instructions are provided to help you diagnose and solve the problem. As a first step, please review the Quick Tips.
updates at http://www.netgear.com/support.
This section describes tips for troubleshooting some common problems:
Be sure to restart your network in this sequence.

Make sure that the Ethernet cables are securely plugged in.
Make sure that the wireless settings in the computer and router match exactly.
Make sure that the network settings of the computer are correct.
Check the Test light to verify correct router operation.
If the Test light does not turn off within 2 minutes after you turn the router on, reset the router according to the instructions in “Restoring the Default Configuration and Password” on page 7-12.
After you turn on power to the router, the following sequence of events should occur:
7-2 Troubleshooting

a. The color of the power light changes to green.
b. The LAN port lights are lit for any local ports that are connected.
If a port’s light is lit, a link has been established to the connected device. If a LAN port is connected to a 100 Mbps device, verify that the port’s light is green. If the port is 10 Mbps, the light will be amber.
c. The Internet port is connected and its light is lit.
If the correct behavior does not occur, see the appropriate following section.
The Power light is not on.
If the Power and other lights are off when your router is turned on:
If the error persists, you have a hardware problem and should contact Technical Support.
The Power light blinks green slowly and continuously.
The router firmware is corrupted.
To restore your firmware:
a. The CD will automatically start and detect the language you are using on your PC. Select a different language option, if you prefer.
b. If the CD does not automatically start, browse the CD and double-click on .
Troubleshooting 7-3

The Power light stays amber.
When the router is turned on, the Power light turns amber for about 20 seconds and then turns green. If the light does not turn green, the router has a problem.
If the Power light is still amber 1 minute after turning on power to the router:
If the error persists, you might have a hardware problem and should contact Technical Support.
The Internet light stays amber.
When the router is turned on, the Internet light turns amber for about 20 seconds and then turns green. If the light does not turn green, the router has a problem.
If the Internet light is still amber 1 minute after turning on power to the router:
The Internet or LAN port lights are not on.
If either the LAN or Internet lights do not light when the Ethernet connection is made, check the following:
The Push 'N' Connect (WPS) push-button blinks amber.
If after using the WPS function the push-button blinks amber, check the following:
7-4 Troubleshooting

For more information on WPS, see “Using Push 'N' Connect (Wi-Fi Protected Setup)” on page 2-13.
If you are unable to log in to the wireless router, check the following:
assign an IP address in the range 169.254.x.x. If your IP address is in this range, verify that you have a good connection from the computer to the router, then restart (reboot) your computer.
Troubleshooting 7-5

If you can access your router, but your router is unable to access the Internet, review the topics in this section:
If your wireless router is unable to access the Internet, and your Internet light is amber, check the wireless router to see if it is able to get an Internet IP address from your service provider. Unless you have a static IP address, your wireless router automatically requests an IP address from your service provider.
To check your wireless router’s Internet IP address:
If your router is unable to obtain an IP address from the your service provider, the problem might be one of the following:
7-6 Troubleshooting

– Inform your service provider that you have bought a new network device, and ask them to use the wireless router’s MAC address, or
– Configure your router to spoof your computer’s MAC address. On the Basic Settings screen in the Router MAC Address section, select “Use this Computer’s MAC Address” and click Apply. Then restart your network in the correct sequence (see the NETGEAR Wireless Router Setup Manual for instructions).
If you are using PPPoE, try troubleshooting your Internet connection.
To troubleshoot a PPPoE connection:
If any of the steps indicate “Failed,” you can attempt to reconnect by clicking Connect. The wireless router will continue to attempt to connect indefinitely.
If you cannot connect after several minutes, you might be using an incorrect service name, user name, or password. There also might be a provisioning problem with your ISP.
PPPoE until data is transmitted to the network.
Troubleshooting 7-7

If your wireless router can obtain an IP address but your computer is unable to load any web pages from the Internet, check the following:
If the wireless router does not save changes you have made in the browser interface, check the following:
Most network devices and routers contain a ping utility that sends an echo request packet to the designated device. The device then responds with an echo reply. Troubleshooting a network is made very easy by using the ping utility in your computer or workstation. This section includes:
7-8 Troubleshooting

You can ping the router from your computer to verify that the LAN path to your router is set up correctly.
To ping the router from a running Windows PC:
ping www.routerlogin.net
You should see a message like this one:
Pinging <IP address > with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
If the path is not functioning correctly, you could have one of the following problems:
– For a wired connection, make sure that the numbered LAN port light is on for the port to which you are connected. If the light is off, follow the instructions in “Troubleshooting Basic Functions” on page 7-2.
– Check that the appropriate LEDs are on for your network devices. If your router and computer are connected to a separate Ethernet switch, make sure that the link lights are on for the switch ports that are connected to your computer and router.
– Verify that the Ethernet card driver software and TCP/IP software are both installed and configured on your computer. – Verify that the IP address for your router and your computer are correct and that the addresses are on the same subnet.
Request timed out · Troubleshooting 7-9

After verifying that the LAN path works correctly, test the path from your computer to a remote device.
ping -n 10
where is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies like those shown in the previous section are displayed. If you do not receive replies:
Select E-mail under Content Filtering in the main menu to display a screen that shows the current date and time of day. The WNR2000 router uses the Network Time Protocol (NTP) to obtain the current time from one of several network time servers on the Internet. Each entry in the log is stamped with the date and time of day. Problems with the date and time function can include the following:
7-10 Troubleshooting

If your wireless adapter is unable to connect, check its connection settings.
To check the adapter’s connection settings:
– Open the Windows Control Panel, and double-click Network Connections.
– In the LAN section, double-click Wireless Network Connection.
If your wireless network does not appear, check these conditions:
Troubleshooting 7-11

If your wireless network appears, but the signal strength is weak, check these conditions:
This section explains how to restore the factory default configuration settings that reset the router’s user name to admin, the password to password, and the IP address to 192.168.1.1.
You can erase the current configuration and restore factory defaults in two ways:
To use the restore settings button:
The factory default settings will be restored so that you can access the router from your Web browser using the factory defaults.
If the wireless router fails to restart, or the Power light continues to blink or turns solid amber, the unit might be defective. If the error persists, you might have a hardware problem and should contact Technical Support at http://www.netgear.com/support.
7-12 Troubleshooting

This appendix provides factory default settings and technical specifications for the Wireless-N 300 Router Model WNR2000.
Table A-1. WNR2000 Router Default Configuration Settings
Router Login URL http://www.routerlogin.net or http://www.routerlogin.com
Login Name (case-sensitive) printed on product label
Login Password (case-sensitive) printed on product label
WAN MAC Address Default hardware address (on label)
Router LAN IP address printed on product label (also known as Gateway IP address)
192.168.1.1
Router Subnet 255.255.255.0
DHCP range 192.168.1.2 to 192.168.1.254
Time Zone Adjusted for Daylight Saving Time Disabled
Allow a Registrar to configure this router Enabled

Table A-1. WNR2000 Router Default Configuration Settings (continued)
Wireless Access List (MAC Filtering) All wireless stations allowed
Transmission Speed Auto*
Country/Region United States (North America only; otherwise varies by country and region)
RF Channel 6 until region selected
Operating Mode 145 Mbps
Inbound (communications coming in from the Internet) Disabled (bars all unsolicited requests except for traffic on port 80, the http port)
Outbound (communications going out to the Internet) Enabled (all)
*. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead lower actual data throughput rate.

Table A-2. WNR2000 Router General Specifications
Network Protocol and Standards Compatibility
Data and Routing Protocols TCP/IP, RIP-1, RIP-2, DHCP, PPPoE, PPTP, Bigpond, Dynamic DNS, and UPnP
North America 120V, 60 Hz, input
UK, Australia 240V, 50 Hz, input
Europe 230V, 50 Hz, input
Japan 100V, 50/60 Hz, input
All regions (output) 12V DC @ 1.0A, output
Dimensions 7" x 5.1" x 1.4" 177.5 x 130 x 35 mm
Weight 0.88 lbs. 0.399 kg
Operating temperature 0 to 40 C (32º to 104º F)
Operating humidity 90% maximum relative humidity, noncondensing
Designed to conform to the following standards
FCC Part 15 Class B EN 55022/24 (CISPR 22/24) Class B EN 60950 (CE LVD) Class B MIC
LAN 10BASE-T or 100BASE-Tx, RJ-45
WAN 10BASE-T or 100BASE-Tx, RJ-45

A-4 Technical Specifications

This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product.
Table B-1. Reference Documents
TCP/IP Networking Basics http://documentation.netgear.com/reference/enu/tcpip/index.htm
Wireless Networking Basics http://documentation.netgear.com/reference/enu/wireless/index.htm
Preparing Your Network http://documentation.netgear.com/reference/enu/wsdhcp/index.htm
Virtual Private Networking Basics
http://documentation.netgear.com/reference/enu/vpn/index.htm
Glossary http://documentation.netgear.com/reference/enu/glossary/index.htm
In addition, you can find initial setup instructions for your wireless router in the NETGEAR Wireless Router Setup Manual.
Document Link · Related Documents B-1

B-2 Related Documents

custom service (port forwarding) 5-7
Ethernet MAC address 6-7
F
data packets, fragmented 5-16
date and time, troubleshooting 7-10
listed A-1 restoring 7-12
daylight savings time 3-9, 7-11
default DMZ server 4-8
default settings A-2 disabling 4-8 overview 2-23
listed A-1 restoring 7-12
default LAN IP configuration 4-3
restoring 7-3 updating 1-3, 6-3, 6-9
fixed font text xi
DHCP server 4-4, 6-5
fixed IP addresses 1-8
fragmented data packets 5-16
firewall 4-8 router PIN 2-17 wireless client association 4-14
games, QoS for 5-20
generating encryption keys 2-10
Documentation Web page 1-4
GUI language version 6-3
Domain Name Server (DNS) addresses
current 6-3 entering 1-8, 1-11
host name 1-8, 6-7
dynamic IP addresses 1-8
HTML version, printing xii
DynDNS.org 4-6
inbound traffic, allowing or blocking 5-1

sending 3-7 time-stamping entries 3-9 viewing 3-6
Internet port, status 6-3
Internet Relay Chat (IRC) 5-3
Internet services, blocking access 3-3
attached devices 6-7 current 6-3 entering 1-8 QoS for 5-19, 5-23 restricting access by 2-19 spoofing 7-7
blocking access by 3-5 current 6-3 dynamic or static 1-8 LAN 4-3 registering domain name 4-6 reserved 4-5
mail server, outgoing 3-8
managing router remotely 6-13
IP subnet mask 4-3, 6-3
ISP settings, basic 1-7
mixed mode encryption 2-3, 2-11
mode, communication 2-8, 6-4
MTU size 4-9, 5-16
N
keywords, blocking by 3-1
NAT (Network Address Translation) 4-8, 4-10, 5-2
Neighbor Friendly mode 2-8
NetBIOS host name 6-7
Network Time Protocol (NTP) 3-9, 7-10
LAN IP setup 4-1
LAN path, troubleshooting 7-9
obstructions, connecting through 5-25
online games, QoS for 5-20
LAN port settings 6-3
Open System authentication 2-9
language, screen display 1-5
outgoing mail server 3-8
local network, default settings A-1
local servers, port forwarding to 5-6
passphrases 2-9, 2-10, 2-11
changing 2-21 restoring 7-12

region of operation 2-7
physical push button (WPS) 2-14
releasing connection status 6-5
remote devices, testing path 7-10
ping 4-9, 7-8
renewing connection status 6-5
reserved IP adresses 4-5
configuring 5-6 example 5-5
configuration 6-8 default factory settings 7-12
configuring 5-10 example 5-3
restricting access by MAC address 2-19
power adapter specifications A-3
RIP (Router Information Protocol) direction 4-3
Power light, troubleshooting and 7-2
route name 4-11, 4-12
Powerline HD products 5-25
router PIN 2-15, 2-17
PPPoE (PPP over Ethernet) 1-10
router status, viewing 6-2
PPTP (Point to Point Tunneling Protocol) 1-9
primary DNS server 1-8, 1-11
screen display language 1-5
secondary DNS server 1-8, 1-11
Push ’N’ Connect 2-13, 6-4, 7-4
push button configuration (WPS) 2-14
options, compared 2-2 setting up 2-1
security PIN 2-15, 2-17
QoS (Quality of Service) 5-18
radio, wireless 1-13, 2-12, 6-4
settings, default. See default factory settings
setup information, gathering 2-5

Shared Key authentication 2-5, 2-9
Smart Setup Wizard 1-6
software push button configuration (WPS) 2-14
Universal Plug and Play (UPnP) 5-14
up time, system 6-6
updating firmware 1-3, 6-3, 6-9
SPI (Stateful Packet Inspection) firewall 4-8
spoofing MAC addresses 1-8, 7-7
SSID broadcast 1-13, 2-12
static IP addresses 1-8
firmware 6-3, 6-9 RIP (Router Information Protocol) 4-3
advanced wireless settings 2-12 attached devices 6-7 basic security settings 2-6 logs 3-6 status 6-2
streaming video and audio 5-25
subnet mask 4-3, 6-3
system up time 6-6
W
TCP/IP network, troubleshooting 7-8
WEP encryption 2-3, 2-9
Wi-Fi Protected Setup (WPS) 2-13, 6-4, 7-4
testing wireless connections 1-11
time of day, troubleshooting 7-10
wildcards, DNS and 4-7
time to live, advertisement 5-15
Wireless Card Access List 2-19
wireless client PIN 2-15
wireless clients, adding 2-13, 2-18, 6-4
idle 1-11 port triggering 5-11
wireless connection type 5-24
Wireless Distribution System (WDS) 4-12
TKIP (Temporal Key Integrity Protocol) encryption 2-11
wireless network name 1-12, 2-7, 6-4
wireless port settings 6-4
wireless radio 1-13, 2-12, 6-4
wireless repeating 4-12, 4-13
transfer time (backing up) 5-26
base station 4-14 repeater unit 4-15

wireless repeating function 4-12, 4-13
wireless security, setting up 2-1
advanced 2-12 basic 2-6 default, listed A-2 gathering information 2-5 testing 1-11
WMM (Wi-Fi Multimedia) 5-18
WPA2-PSK encryption 2-3, 2-10
WPA-PSK + WPA2-PSK encryption 2-3, 2-10
WPA-PSK encryption 2-3, 2-10
wireless settings · Index-6
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.