
ENGLISH
LCD Projector
Commercial Use
Operating Instructions
Model No. PT-LB20NTU
PT-LB20U PT-LB20SU PT-LB20VU
INPUT POWER
VIDEO
RGB
AUTO SETUP
MENU
ENTER
FREEZE SHUTTER
VOLUME D.ZOOM
STD
INDEX WINDOW
PROJECTOR
Before operating this product, please read the instructions carefully and save this manual for future use.

This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required.
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Power Supply: This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60
Hz AC, house current only. CAUTION: The AC power cord which is supplied with the projector as an accessory can
only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, fire may result.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

CAUTION: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only fit a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug. Do not remove
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. FCC CAUTION: To assure continued compliance, use only shielded
interface cables when connecting to computers or peripheral devices. Any unauthorized changes or modifications to this equipment will void the users authority to operate. If you use serial port to connect PC for external control of projector, you must use optional RS-232C serial interface cable with ferrite core. Any unauthorized changes or modifications to this equipment will void the user’s authority to operate. FCC RF Exposure Warning: (if provided with wireless device) – This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. – This equipment has been approved for mobile operation and requires
minimum 20 cm spacing be provided between antenna(s) and all person's body (excluding extremities of hands, wrist and feet) during wireless modes of operation. – This equipment may not be used with other installed transmitters, which
may be capable of simultaneous transmission.

Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. BFor permanently connected equipment, a readily accessible disconnect
device shall be incorporated in the building installation wiring; BFor pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
Declaration of Conformity Model Number: PT-LB20NTU/PT-LB20U/PT-LB20VU/PT-LB20SU Trade Name: Panasonic Responsible party: Panasonic Corporation of North America Address: One Panasonic Way Secaucus New Jersey 07094 Telephone number: 1-800-528-8601 or 1-800-222-0741 Email: pbtsservice@panasonic.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


electric shocks could result. BCheck that no more smoke is coming out, and then contact an Authorized
Service Center for repairs. BDo not attempt to repair the projector yourself, as this can be dangerous. Do not install this projector in a place which is not strong enough to take the full weight of the projector. BIf the installation location is not strong enough, it may fall down or tip over,
and severe injury or damage could result. Installation work (such as ceiling suspension) should only be carried out by a qualified technician. BIf installation is not carried out correctly, there is the danger that injury or
electric shocks may occur. If foreign objects or water get inside the projector, or if the projector is dropped or the cabinet is broken, disconnect the power cord from the wall outlet. BContinued use of the projector in this condition may result in fire or electric
shocks. BContact an Authorized Service Center for repairs. Do not overload the wall outlet. BIf the power supply is overloaded (for example, by using too many
adapters), overheating may occur and fire may result. Do not remove the cover or modify it in any way. BHigh voltages can cause fire or electric shocks. BFor any inspection, adjustment and repair work, please contact an
Authorized Service Center. Clean the power cord plug regularly to prevent it from becoming covered in dust. BIf dust builds up on the power cord plug, the resulting humidity can
damage the insulation, which could result in fire. Pull the power cord plug out from the wall outlet and wipe it with a dry cloth. BIf not using the projector for an extended period of time, pull the power
cord plug out from the wall outlet. Do not do anything that might damage the power cord or the power cord plug. BDo not damage the power cord, make any modifications to it, place it near
any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

BIf the power cord is used while damaged, electric shocks, short-circuits or
fire may result. BAsk an Authorized Service Center to carry out any repairs to the power
cord that might be necessary. Do not handle the power cord plug with wet hands. BFailure to observe this may result in electric shocks. Insert the power cord plug securely into the wall outlet. BIf the plug is not inserted correctly, electric shocks or overheating could
result. BDo not use plugs which are damaged or wall outlet which are coming
loose from the wall. Do not place the projector on top of surfaces which are unstable. BIf the projector is placed on top of a surface which is sloped or unstable, it
may fall down or tip over, and injury or damage could result. Do not place the projector into water or let it become wet. BFailure to observe this may result in fire or electric shocks. Do not place the projector on soft materials such as carpets or sponge mats. BDoing so may cause the projector to overheat, which can cause burns, fire
or damage to the projector. Do not place liquid containers on top of the projector. BIf water spills onto the projector or gets inside it, fire or electric shocks
could result. BIf any water gets inside the projector, contact an Authorized Service
Center. Do not insert any foreign objects into the projector. BDo not insert any metal objects or flammable objects into the projector or
drop them onto the projector, as doing so can result in fire or electric shocks. Keep the batteries out of the reach of infants. BIf the batteries are swallowed, death by suffocation may result. If you
believe that the batteries may have been swallowed, seek medical advice immediately. Do not allow the + and - terminals of the batteries to come into contact with metallic objects such as necklaces or hairpins. BFailure to observe this may cause the batteries to leak, overheat, explode
or catch fire. BStore the batteries in a plastic bag and keep them away from metallic objects. During a thunderstorm, do not touch the projector or the cable. BElectric shocks can result. Do not use the projector in a bath or shower. BFire or electric shocks can result.

Do not look into the lens while the projector is being used. BStrong light is emitted from the projector’s lens. If you look directly into this
light, it can hurt and damage your eyes. BBe especially careful not to let young children look into the lens. In
addition, disconnect the power cord when you are away from the projector. Do not place your hands or other objects close to the air outlet port. BHeated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port, otherwise burns or damage could result. Replacement of the lamp unit should only be carried out by a qualified technician. BThe lamp unit has high internal pressure. If improperly handled, explosion
might result. BThe lamp unit can easily become damaged if struck against hard objects
or dropped, and injury or malfunctions may result. When replacing the lamp, allow it to cool for at least one hour before handling it. BThe lamp cover gets very hot, and touching it can cause burns. Before replacing the lamp, be sure to disconnect the power cord from the wall outlet. BElectric shocks or explosions can result if this is not done.
damage to the projector. BDo not place the projector in narrow, badly ventilated places such as
closets or bookshelves. BDo not place the projector on cloth or papers, as these materials could be
drawn into the air inlet port. Do not set up the projector in humid or dusty places or in places where the projector may come into contact with smoke or steam. BUsing the projector under such conditions may result in fire or electric
shocks. When disconnecting the power cord, hold the plug, not the lead. BIf the power cord itself is pulled, the lead will become damaged, and fire,
short-circuits or serious electric shocks may result. Always disconnect all cables before moving the projector. BMoving the projector with cables still attached can damage the cables,
which could cause fire or electric shocks to occur. Do not place any heavy objects on top of the projector. BFailure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.

Do not short-circuit, heat or disassemble the batteries or place them into water or fire. BFailure to observe this may cause the batteries to overheat, leak, explode
or catch fire, and burns or other injury may result. When inserting the batteries, make sure the polarities (+ and -) are correct. BIf the batteries are inserted incorrectly, they may explode or leak, and fire,
injury or contamination of the battery compartment and surrounding area may result. Use only the specified batteries. BIf incorrect batteries are used, they may explode or leak, and fire, injury or
contamination of the battery compartment and surrounding area may result. Insulate the battery using tape or similar before disposal. BIf the battery comes into contact with metallic objects or other batteries, it
may catch fire or explode. Do not put your weight on this projector. BYou could fall or the projector could break, and injury may result. BBe especially careful not to let young children stand or sit on the projector. If not using the projector for an extended period of time, disconnect the power cord plug from the wall outlet. BIf dust builds up on the power cord plug, the resulting humidity may
damage the insulation, which could result in fire. BThis projector continues to draw approximately 4 W of power even when
the power is turned off. Disconnect the power cord plug from the wall outlet as a safety precaution before carrying out any cleaning. BElectric shocks can result if this is not done. Ask an Authorized Service Center to clean inside the projector at least once a year. BIf dust is left to build up inside the projector without being cleaned out, it
can result in fire or problems with operation. BIt is a good idea to clean the inside of the projector before the season for
humid weather arrives. Ask your nearest Authorized Service Center to clean the projector when required. Please discuss with the Authorized Service Center regarding cleaning costs. We are constantly making efforts to preserve and maintain a clean environment. Please take non repairable units back to your dealer or a recycling company.


small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance:
Check that all of the accessories shown below have been included with your projector.

*PT-LB20NTU only

Caution when moving the projector Be sure to attach the lens cover before moving the projector. The projection lens is extremely susceptible to vibration and shocks. When moving the projector, use the accessory carrying bag. When placing the projector inside the carrying bag, position it so that the lens is facing upward. Do not put anything else in the bag other than the projector and the cables.
Avoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner. The life of the lamp may be shortened.
Do not set up the projector near high-voltage power lines or near motors. The projector may be subject to electromagnetic interference.
If installing the projector to the ceiling, ask a qualified technician to carry out all installation work. You will need to purchase the separate installation kit (Model No.ET-PKB30). Furthermore, all installation work should only be carried out by a qualified technician.
If using this projector at high elevations (above 1 400 m), set the “FAN CONTROL” to “HIGH”. (Refer to page 47.) Failure to observe this may result in malfunctions.

Do not touch the surfaces of the lens with your bare hands. If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen. Moreover, when not using the projector, retract the lens and then cover it with the lens cover.
Screen Do not apply any volatile substances which may cause discoloration to the screen, and do not let it become dirty or damaged.
Lamp The lamp may need to be replaced earlier due to variables such as individual lamp characteristics, usage conditions and the installation environment, especially when the projector is subjected to continuous use for more than 10 hours or the power is frequently turned on and off.
Liquid crystal panel The liquid crystal panel of the projector is built with very high precision technology to provide fine picture details. Occasionally, a few non-active pixels may appear on the screen as fixed points of blue, green or red. Please note that this does not affect the performance of your LCD.

Projector <Top, right and front>
# $ %
&
'
* )
'
(
#Projector control panel (page 16) $Zoom ring (page 25) %Focus ring (page 25) &Security lock
This can be used to connect a commercially-available theft-prevention cable (manufactured by Kensington). This security lock is compatible with the Microsaver Security System from Kensington. 'Leg adjuster buttons (L/R) (page 25)
These buttons are used to unlock the front adjustable legs. Press to adjust the angle of tilt of the projector. (Lens cover )Projection lens *Remote control signal receptor (page 23)

$%$
#
(
'
&
#Connector panel (page 15) $Air outlet port
Do not cover this port. %Speaker &Front adjustable legs (L/R) (page 25) 'Air inlet port, Air filter (page 54)
Do not cover this port. (Lamp unit cover (page 55)
small noise as it operates. This noise may change depending on the ambient temperature. Turning the lamp on or off will cause this noise to increase a little. BBy using the “OPTION” menu to set “LAMP POWER” to “LOW”, the
operating sound of the fan can be reduced. (Refer to page 47.)
face, or objects which cannot withstand heat close to this port, otherwise burns or damage could result.

Connector panel
#Power input socket (AC IN) (page 24)
The accessory power cord is connected here. Do not use any power cord other than the accessory power cord. $SERIAL connector (pages 21, 22 and 64)
This connector is used to connect a personal computer to the projector in order to control the projector externally. (RS-232C compatible) %RGB1 IN connector (pages 21 and 22)
This connector is used to input RGB signals and YPBPR signals. &RGB2 IN/1 OUT connector (pages 21, 22 and 46)
This connector is used to input or output RGB signals and YPBPR signals. Adjust “RGB2 SELECT” in the “OPTION” menu to select whether you want input or output with this connector. 'S-VIDEO IN connector (pages 22 and 42)
This connector is used to input signals from S-VIDEO-compatible equipment such as a video deck. The connector is S1 signal compatible, and it automatically switches between 16:9 and 4:3 aspect ratios in accordance with the type of signal being input. (VIDEO IN connector (page 22)
This connector is used to input video signals from video equipment such as a video deck. )AUDIO IN L-R connectors (pages 21 and 22) *Menu operation (page 16)


#RGB INPUT indicator
This indicator illuminates when a signal is being input to the connector (RGB1 IN or RGB2 IN) selected using the input select buttons. $LAMP indicator (page 53)
This indicator illuminates when it is time to replace the lamp unit. It flashes if a circuit abnormality is detected.

%TEMP indicator (page 52)
This indicator illuminates if an abnormally high temperature is detected inside the projector or around it. If the temperature rises above a certain level, the power supply will be turned off automatically and the indicator will flash. &Illumination sensor (page 39)
This sensor detects the luminance when the “DAYLIGHTVIEW” function is operating. Do not cover the projector and do not place any object on the projector when using it. 'POWER button (pages 24, 26 and 27)
This button is used to turn the power on and off. This button on the projector illuminates red when the projector is in standby mode, and it illuminates green when a picture starts to be projected. (INPUT buttons (page 25)
These buttons are used to switch the input signals from the connected equipment. )AUTO SETUP button (pages 25 and 28)
If this button is pressed while a picture is being projected, the projection settings will be adjusted automatically in accordance with the signal being input. In addition, the angle of tilt of the projector will be automatically detected and adjusted in order to correct any keystone distortion. *MENU button (pages 32 and 34) This button is used to display the “MAIN MENU”. When a menu screen is being displayed, this button can be used to return to a previous screen or to clear the screen. +Arrow (FGI and H) buttons (page 34)
These buttons are used to select and adjust items in the on-screen menus. ,ENTER button (page 34)
This button is used to accept and to activate items selected in the on-screen menus. -FREEZE button (page 29)
This button is used to momentarily freeze projection so that a still picture is displayed. .SHUTTER button (page 29)
This button is used to momentarily turn off the picture and sound. /VOLUME +/- buttons (page 30)
These buttons are used to adjust the volume of the sound output from the projector’s built-in speaker. Refer to page 33 for details on how to adjust the volume without using the remote control unit. 0STD (standard) button (page 35) This button is used to reset the projector adjustment values to the factory default settings. 1INDEX WINDOW button (page 31) This button can be used to split the image projection area into a still picture and a moving picture. When NETWORK is selected, the screen display will be switched between four window style, index style, and 16 Index style. (PT-LB20NTU only. Refer to the accessory CD-ROM for details.) 2D.ZOOM +/- buttons (page 30) These buttons are used to enlarge the projected image.

Projection methods In way of installing projector, any one of the following four projection methods are used. Select whichever projection method matches the setting-up method. (The projection method can be set from the “OPTION” menu. Refer to pages 46 and 47 for details.)
BFront-desk projection BFront-ceiling projection
FRONT
FRONT/REAR
FRONT
DESK/CEILING
DESK
DESK/CEILING
CEILING
(Using a translucent screen)
(Using a translucent screen)
REAR
FRONT/REAR
REAR
DESK/CEILING
DESK
DESK/CEILING
CEILING
when using the ceiling installation method. BDo not set up the projector vertically or tilted horizontally, otherwise it
may cause damage to the projector. BIt is recommended that you set up the projector in a place that is tilted
at less than ±30° vertically. Setting up the projector in places that are tilted at more than ±30° vertically may shorten component life.

Top edge of screen
L: Projection distance SH: Image height SW:Image width H1: Distance from center
Getting started
H1
Bottom edge of screen
of lens to bottom edge of projected image
81.2 mm (3-3/16˝)
Projection distances
PT-LB20NTU/PT-LB20U
(H1) 4:3 Screen size (diagonal)
Wide (LW) Telephoto (LT) Projection distance (L) Height position
— 0.84 m(33˝) 1.02 m(40˝) 1.27 m(50˝) 1.52 m(60˝) 1.78 m(70˝) 2.03 m(80˝) 2.29 m(90˝) 2.54 m(100˝) 3.05 m(120˝) 3.81 m(150˝) 5.08 m(200˝) 6.35 m(250˝) 7.62 m(300˝)
1.1 m(3´7˝) 1.4 m(4´7˝) 1.7 m(5´6˝) 2.1 m(6´10˝) 2.4 m(7´10˝) 2.8 m(9´2˝) 3.2 m(10´5˝) 3.5 m(11´5˝) 4.2 m(13´9˝) 5.3 m(17´4˝) 7.1 m(23´3˝) 8.9 m(29´2˝) 10.7 m(35´1˝)
0.08 m(3-1/8˝) 0.09 m(3-17/32˝) 0.11 m(4-5/16˝) 0.14 m(5-1/2˝) 0.16 m(6-9/32˝) 0.18 m(7-1/16˝) 0.20 m(7-27/32˝) 0.22 m(8-21/32˝) 0.26 m(10-7/32˝) 0.33 m(12-31/32˝) 0.44 m(17-5/16˝) 0.55 m(21-5/8˝) 0.66 m(25-31/32˝)
1.2 m(3´11˝) 1.5 m(4´11˝) 1.8 m(5´10˝) 2.1 m(6´10˝) 2.4 m(7´10˝) 2.7 m(8´10˝) 3.0 m(9´10˝) 3.6 m(11´9˝) 4.5 m(14´9˝) 6.0 m(19´8˝) 7.5 m(24´7˝) 9.0 m(29´6˝)
Screen · Screen

(H1) 4:3 Screen size (diagonal)
Wide (LW) Telephoto (LT) Projection distance (L) Height position
— 0.84 m(33˝) 1.02 m(40˝) 1.27 m(50˝) 1.52 m(60˝) 1.78 m(70˝) 2.03 m(80˝) 2.29 m(90˝) 2.54 m(100˝) 3.05 m(120˝) 3.81 m(150˝) 5.08 m(200˝) 6.35 m(250˝) 7.62 m(300˝)
1.1 m(3´7˝) 1.4 m(4´7˝) 1.8 m(5´10˝) 2.1 m(6´10˝) 2.5 m(8´2˝) 2.9 m(9´6˝) 3.2 m(10´5˝) 3.6 m(11´9˝) 4.3 m(14´1˝) 5.4 m(17´8˝) 7.3 m(23´11˝) 9.1 m(29´10˝) 11.0 m(36´1˝)
0.08 m(3-1/8˝) 0.09 m(3-17/32˝) 0.11 m(4-5/16˝) 0.14 m(5-1/2˝) 0.16 m(6-9/32˝) 0.18 m(7-1/16˝) 0.20 m(7-27/32˝) 0.22 m(8-21/32˝) 0.26 m(10-7/32˝) 0.33 m(12-31/32˝) 0.44 m(17-5/16˝) 0.55 m(21-5/8˝) 0.66 m(25-31/32˝)
1.2 m(3´11˝) 1.5 m(4´11˝) 1.8 m(5´10˝) 2.1 m(6´10˝) 2.4 m(7´10˝) 2.8 m(9´2˝) 3.0 m(9´10˝) 3.7 m(12´1˝) 4.6 m(15´1˝) 6.1 m(20´) 7.6 m(24´11˝) 9.2 m(30´2˝)
(H1) 4:3 Screen size (diagonal)
Wide (LW) Telephoto (LT) Projection distance (L) Height position
— 0.84 m(33˝) 1.02 m(40˝) 1.27 m(50˝) 1.52 m(60˝) 1.78 m(70˝) 2.03 m(80˝) 2.29 m(90˝) 2.54 m(100˝) 3.05 m(120˝) 3.81 m(150˝) 5.08 m(200˝) 6.35 m(250˝) 7.62 m(300˝)
1.4 m(4´7˝) 1.7 m(5´6˝) 2.1 m(6´10˝) 2.5 m(8´2˝) 2.9 m(9´6˝) 3.4 m(11´1˝) 3.8 m(12´5˝) 4.2 m(13´9˝) 5.0 m(16´4˝) 6.3 m(20´8˝) 8.4 m(27´6˝) 10.6 m(34´9˝) 12.7 m(41´8˝)
0.04 m(1-9/16˝) 0.05 m(1-15/16˝) 0.06 m(2-11/32˝) 0.07 m(2-3/4˝) 0.08 m(3-1/8˝) 0.09 m(3-17/32˝) 0.11 m(4-5/16˝) 0.12 m(4-23/32˝) 0.14 m(5-1/2˝) 0.18 m(7-1/16˝) 0.23 m(9-1/32˝) 0.29 m(11-13/32˝) 0.35 m(13-3/4˝)
1.4 m(4´7˝) 1.7 m(5´6˝) 2.1 m(6´10˝) 2.4 m(7´10˝) 2.8 m(9´2˝) 3.1 m(10´2˝) 3.5 m(11´5˝) 4.2 m(13´9˝) 5.2 m(17´) 7.0 m(22´11˝) 8.7 m(28´6˝) 10.5 m(34´5˝)
the 4:3 projection image overflows the screen at the top and bottom. BFor details about projected image distances, refer to
page 63.

available as an option, you may need to prepare a proper cable for the device concerned. BIf there is a lot of jitter in the video signal, the projected image may flicker. In such cases,
it will be necessary to connect a TBC (time base corrector). BRefer to the list on page 62 for details on compatible signals which can be input to the
projector. BOnly one audio system circuit is available for the AUDIO IN L-R connectors, so if you
change the audio input source, you will need to remove and insert the appropriate plugs.

Refer to the accessory CD-ROM for details on the wireless network that can be used for controlling the projector with a personal computer. (PT-LB20NTU only)
SELECT” in the “OPTION” menu is set to “OUTPUT”. (page 46)


Red (connect to PR signal connector) Blue (connect to PB signal connector) Green (connect to Y signal connector)
DVD player Video deck

computer or video deck is turned off while “D.ZOOM”(digital zoom) or “INDEX WINDOW” is being used, these functions will be cancelled.

Insert the accessory lithium battery while making sure that the polarities are correct. #While pushing the battery holder tab to the right, pull out the battery
holder.
$Insert the battery into the battery holder so that the + side is facing
upward.
Match the “+” surface of the battery with the “+” marked side of the battery holder.
%Insert the battery holder.
remote control signal receptor, the operating range is within approximately 7 m (23´) from the surfaces of the receptor. Furthermore, the remote control unit can be operated from an angle of ±30° to the left or right and ±15° above or below the receptor. BIf the buttons on the remote control unit are kept pressed, the battery
power will be consumed rapidly. BIf there are any obstacles in between the remote control unit and the
receptor, the remote control unit may not operate correctly. BIf strong light is allowed to shine onto the remote control signal receptor,
correct projector operation may not be possible. Place the projector as far away from light sources as possible. BIf facing the remote control unit toward the screen to operate the projector,
the operating range of the remote control unit will be limited by the amount of light reflection loss caused by the characteristics of the screen used.
Back side · Push the tab · Pull out


Connect the accessory power cord to the AC IN socket. BThe POWER button on the projector will illuminate red.
Press the POWER button. BThe POWER button on the projector will flash green. After a short
period, it will illuminate green, and a picture will be projected.
Turn on the power of all connected devices. BStart the play function of a device such as a DVD player.

was used the last time, projection will start after the power cord is connected (when “POWER MEMORY” in the “OPTION” menu is set to “ON”). Refer to page 48 for details. BA tinkling sound may be heard when the lamp unit is turned on, but this

Press the input select button to select the input signal.
BA picture will be projected in accordance with the selected input
signal. BWhen a YPBPR signal is being input, “YPBPR” will be displayed
instead of “RGB”. B“NETWORK” is for PT-LB20NTU only.
Follow the procedure below when you set the projector up first, and when you change the setup place.
'
adjust the forward/back angle of tilt of the projector. Adjust so that the projected image is placed at the center of the screen.
Press the AUTO SETUP button to initiate automatic positioning. BThe tilt of the projector and the input
signal will be detected and keystone distortion and the position of the image will be corrected. (Refer to page 28 for details.) Adjusting the size BTurn the zoom ring to adjust the size of the projected image.
Adjusting the focus BTurn the focus ring to adjust the focus of the projected image.


screen.
Press the I or H button to select “OK”, and then press the ENTER button. BThe lamp unit will switch off and the picture will stop being projected.
(The POWER button on the projector will illuminate orange while the cooling fan is still operating.)
Disconnect the power cord after the POWER button on the projector illuminates red.

by holding it down for at least 0.5 seconds. BWhen the projector is in standby mode (the POWER button on the
projector is illuminated red), the projector continues to draw approximately 4 W of power even when the cooling fan has stopped.
POWER button

Direct power off function You can disconnect the power cord during projection or immediately after use and move the projector. The cooling fan will operate by the internal power supply to cool down the lamp. BWhen this function is used, it may take more time for the lamp to turn back
on again compared to when the lamp cools down with the power cord connected. BDo not put the projector in a bag while the POWER button on the
projector is illuminated.
damage the insulation, which could result in fire. BThis projector continues to draw approximately 4 W of power even when
the power is turned off.
POWER button on the projector
Red Illuminated The projector is in standby mode and image projection is possible by pressing the POWER button.
The projector is preparing for projection after the power has been turned on while the POWER button on the projector is illuminated red. (After a short period, a picture will be projected.)
A picture is being projected. The lamp is cooling down after the power has been turned off or while direct power off function is operating. The projector is preparing for projection after the power has been turned on while the POWER button on the projector is illuminated orange. (After a short period, a picture will be projected.)

This projector detects its degree of tilt and the input signal. Keystone distortion and the position of the image can then be corrected automatically in accordance with the input signal.
Press the AUTO SETUP button. (When the projected image has caused keystone distortion)
VIDEO
RGB
MENU AUTO SETUP
ENTER
FREEZE SHUTTER
STD
[
VOLUME D.ZOOM
INDEX WINDOW
will be carried out.
set to “ON”, refer to page 45 for details.) BWhen RGB signals are being input, “DOT CLOCK”, and “CLOCK
PHASE” will be adjusted automatically in addition to keystone distortion and the position of the image being corrected (except when the dot clock frequency is 100 MHz or higher). Refer to page 41 for details. BIf the edges of the projected image are indistinct, or if a dark picture is
being projected, the automatic setup processing may stop automatically before it is complete. If this happens, project a different picture and then press the AUTO SETUP button again. BSet “AUTO KEYSTN” in the “OPTION” menu to “OFF” to prevent any
deterioration of the picture as a result of keystone correction. (Refer to page 45.)

The “SHUTTER” function can be used to momentarily turn off the picture and sound from the projector when the projector is not being used for short periods of time, such as during breaks in meetings or when carrying out preparation. The projector uses less power in “SHUTTER” mode than it does in normal projection mode.
Press the SHUTTER button. BThe picture and sound will be turned off. BPress any button on either the projector or
VIDEO
RGB
remote control unit to return to normal operating mode.
ENTER
SHUTTER
function.
Useful functions
VOLUME D.ZOOM
INDEX WINDOW
PROJECTOR
Pausing a picture (FREEZE)
Press the FREEZE button.
VIDEO
RGB
MENU AUTO SETUP
ENTER
SHUTTER FREEZE
STD
BThe picture being projected will be paused. BPress the FREEZE button again to cancel the
INDEX WINDOW
still picture.
NETWORK is selected. (PT-LB20NTU only)
Still picture

Press the D.ZOOM +/- button.

RGB
MENU AUTO SETUP
ENTER
SHUTTER FREEZE
[
BThe picture will then
be enlarged to 1.5 times the normal size.

D.ZOOM
INDEX WINDOW
PROJECTOR
The remote control unit functions during D.ZOOM (digital zoom)
Press the D.ZOOM +/- buttons to change the enlargement ratio.
Press the F,G,IandHbuttons to move the enlarged area which you want to project. Press the MENU button to return to the normal screen.
steps of 0.1. When RGB signals are being input, the enlargement ratio can be changed within the range of x1 to x3, except when the “FRAME LOCK” is set to “ON”. BIf the type of signal being input changes while the digital zoom function
is being used, the digital zoom function will be cancelled.
Press the VOLUME +/- button. BPress the + button to raise the volume. BPress the - button to lower the volume.
D.ZOOM VOLUME
INDEX WINDOW
“MAIN MENU” to adjust the volume.

This function lets you store a picture which is being projected into memory, so that you can display a still picture and a moving picture on the screen.
Press the INDEX WINDOW button.
BThe aspect ratio of
the screen changes and the image is vertically elongated in comparison to a normal image. BWhen NETWORK is
Still picture
Moving
SHUTTER FREEZE
picture
STD
VOLUME D.ZOOM
INDEX WINDOW
selected, the screen display will be switched between four window style, index style, and 16 Index style. (PT-LB20NTU only. Refer to the accessory CD-ROM for details.)
The remote control unit functions during INDEX WINDOW
Press the F or G button to select a screen size. It can switch to three stages.
Press the I or H button to switch between the still picture screen and moving picture screen.
Press the ENTER button to capture the present moving picture in a still window.
Press the MENU button to return to the previous screen.
change. Make sure that you fully understand the notes on “ASPECT” on page 43 before using the “INDEX WINDOW” function. B“INDEX WINDOW” on the “MAIN MENU” is the same function.

PICTURE menu (page 37) When an RGB signal is being input or NETWORK is selected
Menu screens The various settings and adjustments for this projector can be carried out by selecting the operations from on-screen menus. The general arrangement of these menus is shown below.

PICTURE PICTURE MODE DYNAMIC CONTRAST 32 BRIGHT 32 SHARPNESS 0 COLOR TEMP. STANDARD W-BAL R 32 W-BAL G 32 W-BAL B 32 DAYLIGHTVIEW AI ON SIGNAL MODE XGA STANDARD SELECT ADJ RETRN

MENU KEYSTONE PICTURE POSITION INDEX WINDOW SHUTTER VOLUME LANGUAGE OPTION SECURITY NETWORK SELECT ENTER EXIT
BWhen NETWORK is
selected, “W-BAL R/G/B” settings will not be displayed. (PT-LB20NTU only)
When a YPBPR signal is being input

PICTURE PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 6 COLOR TEMP. STANDARD DAYLIGHTVIEW AI ON SIGNAL MODE 480p STANDARD SELECT ADJ RETRN
BPress the MENU button to
display the “MAIN MENU”. Refer to page 34 for details on how to operate the on-screen menus.
When an S-VIDEO/VIDEO signal is being input

PICTURE PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 8 COLOR TEMP. STANDARD DAYLIGHTVIEW AI ON TV-SYSTEM AUTO STILL MODE OFF STANDARD SELECT ADJ RETRN
KEYSTONE correction (page 36)

POSITION menu (page 41)

#Press the MENU button.
The “MAIN MENU” will be displayed.


MENU KEYSTONE PICTURE POSITION INDEX WINDOW SHUTTER VOLUME LANGUAGE OPTION SECURITY NETWORK SELECT ENTER EXIT
$Press the F or G button to select an item.
Selected item will be displayed in blue.

MENU KEYSTONE PICTURE POSITION INDEX WINDOW SHUTTER VOLUME LANGUAGE OPTION SECURITY NETWORK SELECT ENTER EXIT
%Press the ENTER button to accept the
selection. The selected menu screen or adjustment screen will then be displayed. (Example: “PICTURE” menu)

&Press the F or G button to select
Unavailable on-screen menu items This projector has unadjustable items and unusable functions depending on the signal being input. When an item cannot be adjusted or a function cannot be used, the corresponding on-screen menu display does not appear, and the item or function will not work even if the ENTER button is pressed.
an item, and then press the I or H button to change or adjust the setting. An individual adjustment screen such as the one shown below will be displayed for bar scale items.
The bar scale will turn green when any adjustment changes the setting from the factory set value.
Returning a setting to the factory default If you press the STD (standard) button on the remote control unit, you can return settings to the factory default settings. However, the operation of this function varies depending on which screen is being displayed.
BWhen a menu screen is being
BWhen an individual adjustment
screen is being displayed
PICTURE STD PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 8 COLOR TEMP. STANDARD DAYLIGHTVIEW AI ON TV-SYSTEM AUTO STILL MODE OFF STANDARD SELECT ENTER RETRN
Only the item displayed will be returned to the factory default setting, and the bar scale will appear white.
the bar scale indicate the factory default setting. Items which do not have these triangle symbols cannot be returned to the factory default setting. Indicates the standard factory default setting
All items displayed will be returned to their factory default settings, “STD” will be displayed in the top- right screen and the bar scale will appear white.
Indicates the current adjustment value BThe positions of triangle
“STANDARD” from the menu screen and then press the ENTER button.
symbols vary depending on the type of signal being input.
displayed

Keystone distortion is corrected automatically when the projector’s automatic setup function is used, but this correction will not apply if the screen itself is tilted. In such cases, you can correct the keystone distortion manually with the following procedure.
Vertical keystone distortion correction
Operation Press the H button.

Press the F or G button on the projector or remote control unit to select an item, and then press the I or H button to change the setting. For items with bar scales, press the ENTER button or the I or H button to display the adjustment screen, and then press the I or H button to make the adjustment.
When an S-VIDEO/VIDEO signal is being input
PICTURE PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 8 COLOR TEMP. STANDARD DAYLIGHTVIEW AI ON TV-SYSTEM AUTO STILL MODE OFF STANDARD SELECT ADJ RETRN
When an RGB signal is being input or NETWORK is selected

PICTURE PICTURE MODE DYNAMIC CONTRAST 32 BRIGHT 32 SHARPNESS 0 COLOR TEMP. STANDARD W-BAL R 32 W-BAL G 32 W-BAL B 32 DAYLIGHTVIEW AI ON SIGNAL MODE XGA STANDARD SELECT ADJ RETRN
PICTURE MODE NATURAL [ STANDARD [ DYNAMIC [ BLACK-BD
Select the picture mode that best matches the image source and room conditions. The mode best used in dark rooms is “NATURAL”. For rooms having regular lighting conditions in use, select “STANDARD”. For exceptionally bright rooms, use “DYNAMIC”. “BLACK-BD” is available only when “BLACKBOARD” in the “OPTION” menu is set to “ON”. Select “BLACK-BD” when projecting onto blackboards.
When NETWORK is selected, “W-BAL R/G/B” settings will not be displayed. (PT-LB20NTU only)
When an YPBPR signal is being input

PICTURE PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 6 COLOR TEMP. STANDARD DAYLIGHTVIEW AI ON SIGNAL MODE 480p STANDARD SELECT ADJ RETRN

CONTRAST This adjusts the contrast of the picture. (Adjust the “BRIGHT” setting first if required before adjusting the “CONTRAST” setting.) The picture is bright: I button The picture is dark: H button BRIGHT This adjusts the darker areas (black areas) in the picture. Black areas are too light: I button Dark areas are too solid: H button COLOR (S-VIDEO/VIDEO/YPBPR only) The color is too deep: I button The color is too pale: H button TINT (NTSC/NTSC 4.43/YPBPR only) This adjusts the flesh tones in the picture. The flesh tones are greenish: I button The flesh tones are reddish: H button SHARPNESS To soften the picture details: I button To sharpen the picture details: H button
COLOR TEMP.
This is used to adjust the white areas of the picture if they appear bluish or reddish. White balance R/G/B (W-BAL R/G/B) (RGB only) This is used to adjust the white areas of the picture if they appear colorised. To make the selected color lighter: I button To make the selected color stronger: H button

DAYLIGHTVIEW This adjusts the vividness of the projected images when the projector is used under bright lighting. Press the ENTER button to display the “DAYLIGHTVIEW” screen.
W-BAL [
When fluorescent lamps are used for room lighting.
When incandescent lamps are used for room lighting.
“MODE” in “DAYLIGHTVIEW” is set to “OFF”.
OFF
AUTO The vividness of the projected images will be adjusted according to the lighting condition of the room. ON The projected images will have the highest vividness regardless of the lighting condition of the room. OFF “DAYLIGHTVIEW” is disabled.
AI ON The lamp is controlled according to the input signals to project images with the best quality. OFF “AI” is disabled.
POWER” is set to “LOW”. (Refer to page 47.)
correctly if any objects are placed on the projector. B“AUTO” will be disabled when
“FRONT/REAR” in the “OPTION” menu is set to “REAR”.

SIGNAL MODE (RGB/YPBPR/NETWORK only) This displays the type of signal which is currently being projected. Refer to the list on page 62 for details on each type of signal.
TV-SYSTEM AUTO [ NTSC [ NTSC4.43 [ PAL [ PAL-M [ PAL-N [ SECAM
sRGB is an international color reproduction standard (IEC61966-2- 1) established by the International Electrotechnical Commission (IEC). If you would like the colors in sRGB-compatible pictures to be reproduced more faithfully, make the following settings. #Press the F or G button to
This should normally be set to “AUTO”. If the signal is of such poor quality that the correct format cannot be automatically distinguished, change the setting manually to the required TV system.
select “PICTURE MODE”, and then press the I or H button to select “NATURAL”. $Press the STD (standard)
projector automatically distinguishes between NTSC/NTSC 4.43/PAL/PAL60/ PAL-M/PAL-N/SECAM signals.
button on the remote control unit. %Press the F or G button to
STILL MODE (S-VIDEO/VIDEO only) To reduce flickering of still images (vertical flicker), set “STILL MODE” to “ON”.
select “COLOR TEMP.”, and then press the I or H button to select “STANDARD”.
RGB signals are being input (when “LAMP POWER” is set to “HIGH”, “AI” is set to “OFF”, and “MODE” in “DAYLIGHTVIEW” is set to “OFF”).
back moving images.

POSITION Moves the picture position. Press the ENTER button to display the “POSITION” screen. Press the I or H button to move the picture horizontally. Press the F or G button to move the picture vertically.
When an RGB signal is being input, press the AUTO SETUP button first to initiate automatic positioning. If the optimum setting is not obtained when “AUTO SETUP” is carried out, adjust by the following procedure.
Press the F or G button on the projector or remote control unit to select an item, and then press the I or H button to change the setting. For items with bar scales, press the ENTER button or the I or H button to display the adjustment screen, and then press the I or H button to make the adjustment.
DOT CLOCK (RGB only) Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is projected. If this happens, press the I or H button to adjust so that any such noise is minimised.
When an RGB/YPBPR signal is being input
POSITION POSITION DOT CLOCK 32 CLOCK PHASE 16 ASPECT 4:3 RESIZING ON FRAME LOCK OFF STANDARD SELECT ENTER RETRN
CLOCK PHASE (RGB/YPBPR only) Adjust the “DOT CLOCK” setting first before carrying out this adjustment. Press the I or H button to adjust so that the noise level is least noticeable.
When an S-VIDEO/VIDEO signal is being input
POSITION POSITION ASPECT 4:3 RESIZING ON STANDARD SELECT ENTER RETRN
frequency of 100 MHz or higher are being input, interference may not be completely eliminated when the “DOT CLOCK” and “CLOCK PHASE” adjustments are carried out.

S4:3 The size of the input signal is compressed to 75% and projected. (This is useful for projecting a picture with a 4:3 aspect ratio onto a 16:9 screen.)
ASPECT AUTO [ 4:3 [ 16:9 [ S4:3
AUTO (S-VIDEO only) When an S1 video signal is being input, the aspect ratio is changed automatically to project a 16:9 picture. 4:3 The input signal is projected without change. 16:9 The picture is compressed to a ratio of 16:9 and projected.
When a 4:3 signal is being input.
When using the 16:9 screen
When a horizontally squeezed signal is being input.
S1 video signals B S1 video signals are a type of
video signal with an aspect ratio of 16:9 which include a detector signal. This detector signal is output by some sources such as wide-vision video decks. B When “ASPECT” is set to
“AUTO”, the projector recognizes the detector signal and automatically switches the aspect ratio to 16:9.
[ · [

RESIZING This should normally be set to “ON”. (This setting is only for signals which have lower resolutions than the LCD panels. Refer to page 62 for details.) ON The pixel resolution of the input signal is converted to the same resolution as the LCD panels before being projected. This may sometimes cause problems with the quality of the picture. OFF The input signal is projected at its original resolution, with no pixel conversion. The projected picture will be smaller than normal, so adjust the zoom setting or move the projector forwards or backwards to adjust the picture size if necessary. If set to “OFF”, some features, such as “D.ZOOM” (digital zoom), “KEYSTONE” or “INDEX WINDOW” will not function. FRAME LOCK If the picture’s condition is bad while a RGB moving picture is projected, set “FRAME LOCK” to “ON”. Refer to page 62 for compatible RGB signals.
such as cafes or hotels to display programs for a commercial purpose or for public presentation, note that if the aspect ratio (16:9) selection function is used to change the aspect ratio of the screen picture, you may be infringing the rights of the original copyright owner for that program under copyright protection laws. BIf a 4:3 picture is projected
onto a 16:9 screen, distortion may occur around the edges of the picture so that part of the picture is no longer visible. Programs which have 4:3 aspect ratios should be viewed in 4:3 mode to give proper consideration to the aims and intentions of the original program’s creator.

Press the F or G button on the projector or remote control unit to select a language, then press the ENTER button to accept the setting.
Indicates the language which is currently set. LANGUAGE ENGLISH DEUTSCH FRANÇAIS ESPAÑOL ITALIANO PORTUGUÊS SVENSKA NORSK DANSK POLSKI CESTINA MAGYAR
LANGUAGE ENGLISH ▲
ENGLISH 中文 日本語 SELECT ENTER RETRN

Press the F or G button on the projector or remote control unit to select an item, then press the I or H button to change the setting.
AUTO SEARCH This should normally be set to “ON” ON When the power is turned on and “AUTO SETUP” is running, the projector detects which signals are being input, and uses these signals for projection. (If a picture is being projected, the signal source is not automatically changed.) OFF Use this setting when you do not want the signal source to be changed automatically when the power is turned on and “AUTO SETUP” is running. AUTO SIGNAL This should normally be set to “ON”. ON “AUTO SETUP” will be carried out automatically when the input signal is changed. OFF “AUTO SETUP” will not function when the input signal is changed. AUTO KEYSTN This should normally be set to “ON”. ON During “AUTO SETUP”, the angle of tilt of the projector is detected and keystone distortion is corrected automatically. OFF Use this setting when you do not want automatic keystone correction to be carried out during “AUTO SETUP”, such as when the screen itself is at an angle.
OPTION OSD ON AUTO SEARCH ON AUTO SIGNAL ON AUTO KEYSTN ON RGB2 SELECT INPUT RGB/YP B P R AUTO VGA60/480p 480p SXGA MODE SXGA NR OFF BLACKBOARD OFF ▼ SELECT ADJ RETRN
OPTION ▲ BACK COLOR BLUE FRONT/REAR FRONT DESK/CEILING DESK FAN CONTROL STANDARD LAMP POWER HIGH LAMP RUNTIME 10H FUNC 1 DAYLIGHT CONTROL KEY ON AUTO POW.OFF DISABLE POWER MEMORY ON SELECT ADJ RETRN
OSD ON The signal name is displayed in the top-right corner of the screen when the input signal is changed. OFF Use this setting when you do not want the signal name to be displayed.
will also be displayed when an S-VIDEO/VIDEO signal is being input.

RGB2 SELECT This setting is used to select the function of the RGB2 IN/1 OUT connector. RGB/YPBPR
Noise Reduction (NR) (S-VIDEO/VIDEO only) If the signal is of such poor quality that picture interference appears, set “NR” to “ON”. To turn off the “NR” feature, set to “OFF”. BLACKBOARD Set to “ON” when “PICTURE MODE” is set to “BLACK-BD”. (Refer to page 37.) BACK COLOR
RGB [ YP B P R
This should normally be set to “AUTO”. RGB or YPBPR is selected automatically depending on the synchronising signal status. When 480i, 576i, 480p, 576p, 1 080/60i, 1 080/50i, 720/60p and some VGA480 signals are being input, select “RGB” or “YPBPR” in accordance with the input signal. VGA60/480p
This sets the color which is projected onto the screen when no signal is being input to the projector. FRONT/REAR
VGA60/480p 480p [ VGA60
This setting should be changed in accordance with the projector setting-up method. (Refer to page 18.) FRONT When the projector is placed in front of a screen. REAR When using a translucent screen.
Set to “VGA60” when 59.9Hz VGA480 signals are being input (refer to page 62 for details). Set to “480p” when 480p RGB signals are being input. SXGA MODE
This setting is only for an SXGA signal. SXGA Select this item normally. SXGA+ When the edges of the projected image are not visible, select this item.

LAMP RUNTIME This setting displays the usage time for the lamp unit which is currently being used. When replacing the lamp unit, follow the instructions on page 56, and reset “LAMP RUNTIME” to “0”.
This setting should be changed in accordance with the projector setting-up method. (Refer to page 18.) DESK When the projector is placed on a desk or similar. CEILING When the projector is suspended from a ceiling using the ceiling bracket (sold separately). FAN CONTROL
depending on the usage conditions (such as the “LAMP POWER” setting and the number of times the power is turned on and off).
FAN CONTROL STANDARD [ HIGH
This assigns a function to the FUNC1 button of the ET-RM300 wireless remote control unit (sold separately). DAYLIGHT Functions in the same way as when “DAYLIGHTVIEW” is selected from the “PICTURE” menu. (page 39) KEYSTONE Functions in the same way as when “KEYSTONE” is selected from the “MAIN MENU”. (page 36)
Set “FAN CONTROL” to “HIGH”, when using this projector at high elevations (above 1 400 m) only. LAMP POWER
LAMP POWER HIGH [ LOW
This setting changes the lamp brightness. When set to “LOW”, the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. This can help to extend the lamp’s operating life. If using the projector in small rooms where high luminance is not required, it is recommended that you set the “LAMP POWER” to “LOW”.
when no signal is being input.

CONTROL KEY To disable the buttons on the projector, set “CONTROL KEY” to “OFF”. A confirmation screen will then be displayed. Select “OK” by using I or H button. To use the buttons on the projector, set to “ON” by using the remote control unit. AUTO POW.OFF If no signal is input to the projector for the duration of the period you set, the projector will return to standby mode. The period can be set from 15 minutes to 60 minutes in 5 minute intervals. If you don’t use this feature, set it to “DISABLE”. This feature will not function when using the “FREEZE” function. POWER MEMORY This sets the projector’s start up status for when the power cord is connected. ON The projector will start from the same status as when the power cord was disconnected. If the power cord was disconnected during projection when the projector was used the last time, projection will start after the power cord is connected. OFF The projector will be in standby mode.

This projector is equipped with a security function. A password input screen can be displayed, or a company URL can be set up and displayed at the bottom of the projected image.
Press the F or G button on the projector or remote control unit to select “SECURITY”, then press the ENTER button.

INPUT PASSWD The password input screen can be displayed when the power is turned on. All of the controls other than the POWER button are disabled unless the password is entered correctly. ON “INPUT PASSWD” is enabled. OFF “INPUT PASSWD” is disabled. The password input screen will not be displayed when the power is turned on. AMEND PASSWD Passwords can be changed. Press the ENTER button to display the “AMEND PASSWD” screen.

MENU KEYSTONE PICTURE POSITION INDEX WINDOW SHUTTER VOLUME LANGUAGE OPTION SECURITY NETWORK SELECT ENTER EXIT
(When you use the “SECURITY” function for the first time) Press the F, H, G, I, F, H, G and I buttons in order, then press the ENTER button. (When a password change has been made before) Type in the changed password, then press the ENTER button.
F,G,I, and H buttons. (A maximum of 8 buttons can be set.) $Press the ENTER button. %Enter the password again for

SECURITY INPUT PASSWD OFF AMEND PASSWD TEXT DISPLAY OFF TEXT CHANGE SELECT ADJ RETRN

TEXT DISPLAY You can set text to be displayed at the bottom of the projected image at all times. ON “TEXT DISPLAY” is enabled. OFF “TEXT DISPLAY” is disabled. TEXT CHANGE The text which is displayed when “TEXT DISPLAY” is set to “ON” can be changed. Press the ENTER button to display the “TEXT CHANGE” screen.
appear as . It will not be displayed on the screen. BIf you enter the wrong
password, the letters “PASSWORD” and “NEW” will become red. Enter the correct password again.
T E X T C H A N G E
PQRSTUVWXYZ;:,.
#Press the F, G, I and H
buttons to select the characters, then press the ENTER button. (You can enter 22 characters continuously.) CSelect “BS” to delete a
character. $Press the F, G, I and H
buttons to select “OK”, then press the ENTER button. CSelect “Cancel” to cancel the
change.

You need to make adjustments on some items when controlling the projector with a personal computer by means of the wireless network. Refer to the accessory CD-ROM for details.
INPUT PASSWD Set to “ON” if you want password confirmation to be used when controlling the projector with a personal computer by means of the wireless network. AMEND PASSWD Passwords can be changed. WEB CONTROL To control the projector with a personal computer by means of the wireless network, set the “WEB CONTROL” to “ON”. STATUS The network settings will be displayed. DEFAULT Network settings can be returned to the factory default settings.
NETWORK NETWORK 1 NAME CHANGE LB20NT INPUT PASSWD OFF AMEND PASSWD WEB CONTROL ON STATUS DEFAULT SELECT ENTER RETRN
NETWORK Select the network setting you want to use. NAME CHANGE The name for this projector can be set.

There are two indicators on the control panel of the projector which give information about the operating condition of the projector. These indicators illuminate or flash to warn you about problems that have occurred inside the projector, so if you notice that one of the indicators is on, turn off the power and check the table below for the cause of the problem.
Flashing (red) (Lamp unit off)
The surrounding temperature or the temperature inside the projector has become unusually high.
The surrounding temperature or the temperature inside the projector has become dangerously high, causing the lamp unit to automatically shut off.
BThe ventilation holes may be covered. BThe ambient temperature in the place of use may be too high. BThe air filter may be blocked.
BUncover the ventilation holes. BSet up the projector in a place where the temperature is
between 0 °C (32 °F) and 40 °C (104 °F) and the humidity is between 20% and 80% (with no condensation). [If you set the “FAN CONTROL” to “HIGH” (page 47), set up the projector in a place where the temperature is between 0 °C (32 °F) and 35 °C (95 °F) and the humidity is between 20% and 80% (with no condensation).] BDisconnect the power cord by following the procedure on page
26, and then clean the air filter. (Refer to page 54.)

It is nearly time to replace the lamp unit.
An abnormality has been detected in the lamp circuit.
BThe power may
BThere may be an
LAMP” appear on the screen after the projector is turned on?
have been turned on straight away after it was turned off.
abnormality in the lamp circuit.
BThis occurs when
BWait for a while
the operation time for the lamp unit is nearing 1 800 hours (when “LAMP POWER” has been set to “HIGH” and when “AI” has been set to “OFF”). Ask your dealer or an Authorized Service Center to replace the lamp unit.
until the lamp unit cools down before turning the power back on again.
power cord by following the procedure on page 26, and then contact an Authorized Service Center.
in “Turning off the power” on page 26 before carrying out any of the procedures in the “Remedy” column. BIf the TEMP indicator is illuminated and the power turns off after the
procedures in the “Remedy” column have been carried out, it means an abnormality has occurred. Please contact an Authorized Service Center so that the necessary repairs can be made.

If the air filter becomes clogged with dust, the internal temperature of the projector will rise, the TEMP indicator will illuminate and the projector’s power will turn off (the TEMP indicator will flash after the power is turned off). The air filter should be cleaned every 100 hours of use.
Cleaning Use a vacuum cleaner to clean off any accumulated dust.
Replacement procedure #Turn off the power and
disconnect the power cord. Be sure to disconnect the power cord by following the procedure given on page 26.
$Gently turn the projector
upside down, and then remove the air filter cover.
%Replace the air filter, and then
install the air filter cover.
by a vacuum cleaner, remove the air filter and soak it in water, and then wash out the dust by hand. Be sure to install the air filter after it has dried. BDo not use detergent when
washing the air filter. BIf the dust cannot be removed
by cleaning, it is time to replace the air filter. Please consult your dealer. Furthermore, if the lamp unit is being replaced, replace the air filter at this time also.
before using the projector. If the projector is used without the air filter installed, dust and other foreign particles will be drawn into the projector, and malfunctions will result.
Air filter cover · Air filter cover · Air filter

Lamp unit replacement period The lamp is a consumable product. Even when the full life of the bulb has not been exhausted, the brightness of the light will gradually decline. Therefore periodic replacement of the lamp is necessary. The intended lamp replacement interval is 2 000 hours, but it is possible that the lamp may need to be replaced earlier due to variables such as a particular lamp’s characteristics, usage conditions and the installation environment. Early preparation for lamp replacement is encouraged. The lamp will automatically shut off after approximately 10 minutes when 2 000 hours of use have been reached because of a much greater chance of it exploding after this time. NOTE: BThe projector is not supplied
and touching it can cause burns.
made of glass, so dropping it or allowing it to hit hard objects may cause it to burst. Be careful when handling the lamp. BDispose of the removed old lamp
with the same care that would be taken with a fluorescent light. BA Phillips screwdriver is
necessary for removing the lamp unit.
with a replacement lamp unit. Please ask your dealer for details. Lamp unit product no.: ET-LAB10 CAUTION: BDo not use any lamp unit other
above are for when “LAMP POWER” in the “OPTION” menu has been set to “HIGH” and when “AI” in the “PICTURE” menu has been set to “OFF”. If “LAMP POWER” is set to “LOW”, or “AI” is set to “ON”, the life of the lamp can be extended. BWhile 2 000 hours is the
than the one with the product number indicated above.
intended replacement interval, it is not a period of time covered by warranty.

LAMP indicator On-screen display
Displayed for 30 seconds. Pressing any button will clear the display.
More than 1 800 hours
Illuminates red during image projection and standby mode.
Remains displayed until any button is pressed. More than 2 000 hours
been set to “HIGH” and when “AI” has been set to “OFF”), the projector will switch to standby mode after approximately 10 minutes of operation. The steps ) to - on the next page should thus be completed within 10 minutes.
#Disconnect the power cord
%Use a Phillips screwdriver to
from the projector by following the procedure on page 26, and check that the area around the lamp unit has cooled down. $Use a Phillips screwdriver to
loosen the two lamp unit fixing screws until the screws turn freely. Then hold the handle of the lamp unit and gently pull it out from the projector.
turn the lamp unit cover fixing screws at the bottom of the projector, and then remove the lamp unit cover.
Lamp unit fixing screws
&Insert the new lamp unit while
making sure that the direction of insertion is correct, and then use a Phillips screwdriver to securely tighten the lamp unit fixing screws. When inserting the new lamp unit, be sure to push it in at the point A and B.
Lamp unit cover fixing screws
Handle · Lamp unit cover

'Install the lamp unit cover, and
+Press the ENTER button to
then use a Phillips screwdriver to securely tighten the lamp unit cover fixing screws.
display the “OPTION” menu, and then press the F or G button to select “LAMP RUNTIME”.
OPTION ▲ BACK COLOR BLUE FRONT/REAR FRONT DESK/CEILING DESK FAN CONTROL STANDARD LAMP POWER HIGH LAMP RUNTIME 1820H FUNC 1 DAYLIGHT CONTROL KEY ON AUTO POW.OFF DISABLE POWER MEMORY ON SELECT RETRN
and the lamp unit cover securely. If they are not securely installed, it may cause the protection circuit to operate so that the power cannot be turned on.
(Connect the power cord. )Press the POWER button so
that a picture is projected onto the screen.
,Press and hold the ENTER
button for approximately 3 seconds.
OPTION ▲ BACK COLOR BLUE FRONT/REAR FRONT DESK/CEILING DESK FAN CONTROL STANDARD LAMP POWER HIGH TIME RESET [POWER OFF] FUNC 1 DAYLIGHT CONTROL KEY ON AUTO POW.OFF DISABLE POWER MEMORY ON SELECT RETRN
disconnected during projection when the projector was used the last time, projection will start after the power cord is connected (when “POWER MEMORY” in the “OPTION” menu is set to “ON”). Refer to page 48 for details.
*Press the MENU button to display the “MAIN MENU”, and then press the F or G button to select “OPTION”.
The “LAMP RUNTIME” will change to “TIME RESET [POWER OFF]”.
MENU KEYSTONE PICTURE POSITION INDEX WINDOW SHUTTER VOLUME LANGUAGE OPTION SECURITY NETWORK SELECT ENTER EXIT
the lamp time resetting screen will be cancelled.
-Turn off the power and
disconnect the power cord. This will reset the cumulative usage time for the lamp unit to “0”. Refer to page 26 for details on how to turn off the power.

Before calling for service, check the following points.
Problem Possible cause Page Power does not turn on.
BThe power cord may not be connected. BThe main power supply is not being supplied to the
wall outlet. BTEMP indicator is illuminated or flashing. BLAMP indicator is illuminated or flashing. BThe lamp unit cover has not been securely
installed. BThe video signal input source may not be
No picture appears.
connected properly. BThe input selection setting may not be correct. BThe “BRIGHT” adjustment setting may be at the
minimum possible setting. BThe “SHUTTER” function may be in use. BThe lens cover may still be attached to the lens. BThe lens focus may not have been set correctly. BThe projector may not be at the correct distance
The picture is fuzzy.
from the screen. BThe lens may be dirty. BThe projector may be tilted too much. B“COLOR” or “TINT” adjustment may be incorrect. BThe input source which is connected to the
The color is pale or grayish.
projector may not be adjusted correctly. BThe audio signal source may not be connected
No sound can be heard.
properly. BThe volume adjustment may be at the lowest
possible setting. BThe battery may be weak. BThe battery may not be inserted correctly. BThe remote control signal receptor on the projector
The remote control unit does not operate.
may be obstructed. BThe remote control unit may be out of the
operation range. BThe “CONTROL KEY” may be set to “OFF”.
The buttons on the projector do not function.
In order to set the “CONTROL KEY” to “ON” without using the remote control unit, keep holding down the ENTER button on the projector and press the MENU button for more than 2 seconds.
52 53 – · 30, 33 · – 23 23

Problem Possible cause BThe signal format (“TV-SYSTEM”) may not be set
The picture does not display correctly.
correctly. BThere may be a problem with the video tape or
other signal source. BA signal which is not compatible with the projector
may be being input. BThe cable may be too long. BThe external video output for the laptop computer
Picture from computer does not appear.
may not be set correctly. (You may be able to change the external output settings by pressing the [Fn]+[F3] or [Fn]+[F10] keys simultaneously. The actual method varies depending on the type of computer, so refer to the documentation provided with your computer for further details.) BIf an RGB INPUT indicator is turned off, the video
signals may not be output from the computer. B“RGB2 SELECT” in the “OPTION” menu is set to
“OUTPUT” when the signals are input to RGB2 IN/1 OUT connector.
Before carrying out cleaning and maintenance, be sure to disconnect the power cord plug from the wall outlet. Wipe the cabinet with a soft, dry cloth. If the cabinet is particularly dirty, soak the cloth in water with a small amount of neutral detergent in it, squeeze the cloth very well, and then wipe the cabinet. After cleaning, wipe the cabinet dry with a dry cloth. If using a chemically-treated cloth, read the instructions supplied with the cloth before use. Do not wipe the lens with a cloth that is dusty or which produces lint. If any dust or lint gets onto the lens, such dust or lint will be magnified and projected onto the screen. Use a blower to clean any dust and lint from the lens surface, or use a soft cloth to wipe off any dust or lint.
Page

Power supply: 100 V - 240 V ~, 50 Hz/60 Hz Power consumption: 220 W [During standby (when fan is stopped): Approx. 4 W] Amps: 2.5 A - 1.3 A LCD panel:
Panel size (diagonal):
PT-LB20NTU/PT-LB20U/PT-LB20SU: 0.7 type (17.78 mm) PT-LB20VU: 0.6 type (15.24 mm) Aspect ratio: 4:3 Micro lens array: Available Display method: 3 transparent LCD panels (RGB) Drive method: Active matrix method Pixels:
PT-LB20NTU/PT-LB20U/PT-LB20VU: 786 432 (1 024 x 768) x 3 panels PT-LB20SU: 480 000 (800 x 600) x 3 panels Lens: Manual zoom (1 - 1.2) / Manual focus PT-LB20NTU/PT-LB20U/PT-LB20VU: F 1.7 - 1.9 f 21.5 mm - 25.8 mm PT-LB20SU: F 1.8 - 2.1 f 22.0 mm - 26.2 mm Lamp: UHM lamp (155 W) Luminosity:
Horizontal scanning frequency: 15 kHz - 91 kHz Vertical scanning frequency: 50 Hz - 85 Hz Dot clock frequency: Less than 100 MHz YPBPR signals: 480i, 576i, 480p, 576p, 1 080/60i, 1 080/50i, 720/60p Color system: 7 (NTSC/NTSC 4.43/PAL/PAL-M/PAL-N/ PAL60/SECAM) Projection size: 838.2 mm - 7 620 mm (33˝ - 300˝) Throw distance:
PT-LB20NTU/PT-LB20U: 1.1 m - 10.7 m (3´7˝ - 35´1˝) PT-LB20SU: 1.1 m - 11.0 m (3´7˝ - 36´1˝) PT-LB20VU: 1.4 m - 12.7 m (4´7˝ - 41´8˝) Optical axis shift:
PT-LB20NTU/PT-LB20U/PT-LB20SU: 6:1 (fixed) PT-LB20VU: 12:1 (fixed) Screen aspect ratio: 4:3 Installation: Front/Rear/Ceiling/Desk (menu selection) Speaker: 4 cm x 3 cm oval x 1 Max. usable volume output: 1 W (mono) Wireless LAN (PT-LB20NTU only): IEEE802.11 b/g

RGB IN/OUT: Dual line, D-sub HD 15-pin (female) (One line is available for input and output, selectable using an on-screen menu) During YPBPR input/output:
Y: 1.0 V [p-p] (Including sync), 75 Ω PB, PR : 0.7 V [p-p], 75 Ω During RGB input/output:
R.G.B.: 0.7 V [p-p], 75 Ω G.SYNC: 1.0 V [p-p], 75 Ω HD, VD: TTL, automatic positive/negative polarity compatible VIDEO IN: Single-line, RCA pin jack, 1.0 V [p-p], 75 Ω S-VIDEO IN: Single-line, Mini DIN 4-pin Y 1.0 V [p-p], C 0.286 V [p-p], 75 Ω AUDIO IN: Single-line, RCA pin jack x 2 (L-R) 0.5 V [rms] SERIAL: DIN 8-pin RS-232C compatible Cabinet: Moulded plastic (PC/ABS) Dimensions:
Temperature: 0 °C - 40 °C (32 °F - 104 °F) [When the “FAN CONTROL” is set to “HIGH” (page 47): 0 °C - 35 °C (32 °F - 95 °F)] Humidity: 20% - 80% (no condensation) Certifications: UL60950, C-UL FCC Class B <Remote control unit>
Power supply: 3 V DC (Lithium CR2025 battery x1) Operating range: Approx. 7 m (23´) (when operated directly in front of signal receptor) Weight: 18 g (0.6 ozs.) (including battery) Dimensions:
Ceiling bracket ET-PKB30 Wireless remote control unit ET-RM300 Serial adapter ET-ADSER (DIN 8-pin/D-sub 9-pin)
Connectors

LB20NTU LB20U LB20VU
LB20SU
LB20SU
NTSC/NTSC4.43/
720 x 480i 15.7 59.9 A A OK OK Video/S-Video
720 x 576i 15.6 50.0 A A OK OK Video/S-Video 720 x 480i 15.7 59.9 13.5 A A OK OK YPBPR/RGB 720 x 576i 15.6 50.0 13.5 A A OK OK YPBPR/RGB 720 x 483 31.5 59.9 27.0 A A OK OK YPBPR/RGB 720 x 576 31.3 50.0 27.0 A A OK OK YPBPR/RGB 1 920 x 1 080i 33.8 60.0 74.3 A A YPBPR/RGB 1 920 x 1 080i 28.1 50.0 74.3 A A YPBPR/RGB 1 280 x 720 45.0 60.0 74.3 A A YPBPR/RGB 640 x 400 31.5 70.1 25.2 A A OK OK RGB 640 x 400 37.9 85.1 31.5 A A OK OK RGB 640 x 480 31.5 59.9 25.2 A A OK OK RGB 640 x 480 35.0 66.7 30.2 A A OK OK RGB 640 x 480 37.9 72.8 31.5 A A OK OK RGB 640 x 480 37.5 75.0 31.5 A A OK OK RGB 640 x 480 43.3 85.0 36.0 A A OK OK RGB 800 x 600 35.2 56.3 36.0 A AA OK RGB 800 x 600 37.9 60.3 40.0 A AA OK RGB 800 x 600 48.1 72.2 50.0 A AA OK RGB 800 x 600 46.9 75.0 49.5 A AA OK RGB 800 x 600 53.7 85.1 56.3 A AA OK RGB 832 x 624 49.7 74.6 57.3 A A OK RGB 1 024 x 768 48.4 60.0 65.0 AA A RGB 1 024 x 768 56.5 70.1 75.0 AA A RGB 1 024 x 768 60.0 75.0 78.8 AA A RGB 1 024 x 768 68.7 85.0 94.5 AA A RGB 1 024 x 768i 35.5 87.0 44.9 AA A RGB 1 152 x 864 64.0 71.2 94.2 A A RGB 1 152 x 864 67.5 74.9 108.0 B B RGB 1 152 x 864 76.7 85.0 121.5 B B RGB 1 152 x 870 68.7 75.1 100.0 B B RGB 1 280 x 960 60.0 60.0 108.0 B B RGB 1 280 x 1 024 64.0 60.0 108.0 B B RGB 1 280 x 1 024 80.0 75.0 135.0 B B RGB 1 280 x 1 024 91.1 85.0 157.5 B B RGB 1 400 x 1 050 64.0 60.0 108.0 B B RGB 1 400 x 1 050 65.1 59.9 122.4 B B RGB 1 600 x 1 200 75.0 60.0 162.0 B B RGB
480i 576i 480p 576p 1 080/60i 1 080/50i 720/60p VGA400
SVGA
MAC16
XGA
MXGA
MAC21 MSXGA
SXGA
* 4 * 4 * 4
*1 The “i” appearing after the resolution indicates an interlaced signal. *2 The following symbols are used to indicate picture quality. AA Maximum picture quality can be obtained. A Signals are converted by the image processing circuit before picture is projected. B Some loss of data occurs to make projection easier. *3 Signals with “OK” are compatible with the “RESIZING” function. (page 43) *4 Signals that are compatible with the “FRAME LOCK” function. (page 43)

If the screen size (diagonal) is SD (m), then the following formula is used to calculate the projection distance for the wide lens position (LW) and the projection distance for the telephoto lens position (LT).
4:3
SH
H1
LW/LT
SW
For 16:9 aspect ratios, the following formula can be used to calculate the projection distance.
*The values obtained from the formulas above are approximate.

The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer which is connected to this connector.
Communications settings
Signal level RS-232C Asynchronous Sync. method Baud rate Parity
9 600 bps None Character length 8 bits Stop bit 1 bit X parameter None S parameter None
Basic format The data sent from the computer to the projector is transmitted in the format shown below.
Serial Interface Cable with ferrite core, type ET-ADSER.
Start byte (02h) 3 bytes 1 byte 1 byte-5 bytes End byte
the command for 10 seconds after the lamp is switched on. Wait 10 seconds before sending the command. BIf sending multiple commands,
Pin No.
check that a response has been received from the projector for one command before sending the next command. BWhen a command which does
% RXD Received data & GND Earth ' TXD Transmitted data # $ Connected internally ( ) *
not require parameters is sent, the colon (:) is not required. BIf an incorrect command is sent
from the personal computer, the “ER401” command will be sent from the projector to the personal computer.

Control commands The commands which the personal computer can use to control the projector are shown in the following table.
Command Control Contents Remarks
In standby mode, all commands other than the PON command are ignored. BThe PON command is ignored during
lamp ON control. BIf a PON command is received while the
cooling fan is operating after the lamp has switched off, the lamp is not turned back on again straight away, in order to protect the lamp.
Volume AVL Parameter 000-063 (Adjustment value 0-63)
Parameter VID=VIDEO SVD=S-VIDEO RG1=RGB1 RG2=RGB2 NWP=NETWORK (PT-LB20NTU only)
Input signal selection IIS
Callback 0 = Standby 1 = Lamp ON control active 2 = Lamp ON 3 = Lamp OFF control active
Lamp ON condition query Q$S
Operation will be switched between ON and OFF each time the command is sent. Do not switch operation ON and OFF after only short periods of time.
Cable specifications (When connected to a personal computer)
At the projector At the computer (DTE specifications)
Power ON PON · Power OFF POF · Shutter function OSH

41.8(1-5/8)
81.2(3-3/16)
BVGA and XGA are trademarks of International Business Machines
Corporation. BMacintosh is a registered trademark of Apple Computer, Inc. BS-VGA is a registered trademark of the Video Electronics Standards
Association. All other trademarks are the property of the various trademark owners.
These Operating Instructions are printed on recycled paper.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Power does not turn on. | BThe power cord may not be connected. BThe main power supply is not being supplied to the wall outlet. BTEMP indicator is illuminated or flashing. BLAMP indicator is illuminated or flashing. BThe lamp unit cover has not been securely installed. | p.58 | |
| No picture appears. | BThe video signal input source may not be connected properly. BThe input selection setting may not be correct. BThe “BRIGHT” adjustment setting may be at the minimum possible setting. BThe “SHUTTER” function may be in use. | p.58 | |
| The picture is fuzzy. | BThe lens cover may still be attached to the lens. BThe lens focus may not have been set correctly. BThe projector may not be at the correct distance from the screen. BThe lens may be dirty. BThe projector may be tilted too much. | p.58 | |
| The color is pale or grayish. | B“COLOR” or “TINT” adjustment may be incorrect. BThe input source which is connected to the projector may not be adjusted correctly. | p.58 | |
| No sound can be heard. | BThe audio signal source may not be connected properly. BThe volume adjustment may be at the lowest possible setting. | p.58 | |
| The remote control unit does not operate. | BThe battery may be weak. BThe battery may not be inserted correctly. BThe remote control signal receptor on the projector may be obstructed. BThe remote control unit may be out of the operation range. | p.58 | |
| The buttons on the projector do not function. | BThe “CONTROL KEY” may be set to “OFF”. In order to set the “CONTROL KEY” to “ON” without using the remote control unit, keep holding down the ENTER button on the projector and press the MENU button for more than 2 seconds. | p.58 | |
| The picture does not display correctly. | BThe signal format (“TV-SYSTEM”) may not be set correctly. BThere may be a problem with the video tape or other signal source. BA signal which is not compatible with the projector may be being input. | p.59 | |
| Picture from computer does not appear. | BThe cable may be too long. BThe external video output for the laptop computer may not be set correctly. (You may be able to change the external output settings by pressing the [Fn]+[F3] or [Fn]+[F10] keys simultaneously. The actual method varies depending on the type of computer, so refer to the documentation provided with your computer for further details.) BIf an RGB INPUT indicator is turned off, the video signals may not be output from the computer. B“RGB2 SELECT” in the “OPTION” menu is set to “OUTPUT” when the signals are input to RGB2 IN/1 OUT connector. | p.59 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.