
CASSETTE RECORDER
SV-665B SV-662B SV-661B SV-262B SV-265B SV-661I SV-261B SV-261I
Instruction Manual

About this manual
RISK OF ELECTRIC SHOCK
Thank you for purchasing a Samsung Video Cassette Recorder (VCR). Your Owner’s Instructions contain much valuable information on setting up and using your VCR. Please take the time to read them as they will help you take full advantage of your VCR’s features.
DANGER
This symbol is intended to alert you to the presence of dangerous voltage within the product.
The instructions in this manual are for models, SV-665B, SV-661B, SV-265B, SV-261B, SV-662B, SV-262B, SV-661I and SV-261I. Before you start reading this manual please check your model number. It is displayed on the rear of the VCR.
- #(SV-665B): Exceptions only for a certain model, for example SV-665B.
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used.
only relevant to one model.
This symbol is intended to alert you to the presence of important instructions accompanying the product.
Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.
Feature Model SV-665B SV-661B SV-265B SV-261B SV-661I SV-261I
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains socket, as there is a risk of shock hazard from the bared flexible cord.
AV2 IN socket G G G
Format 16:9 G G G
IPC (Intelligent Picture Control) G G G G G G
Timer Programming G G G G G G
As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: -
Changing recording speed (SP/LP) G G G G G G
Hi-Fi & NICAM G G G
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
Using the TV Buttons On the G Remote Control


Front View of the VCR


The lightning bolt is a warning sign alerting you to dangerous voltage inside the product. DO NOT OPEN THE VCR. Refer to service personnel.
Do NOT expose the VCR to extreme temperature condi- tions (below 5°C and above 40°C) or to extreme humidity conditions (less than 10% and more than 75%).
Do NOT place any objects on the VCR or remote control.
During a storm and/or light- ning, unplug the VCR from the mains socket and aerial.
If the remote control is not used for a long period of time, remove the batteries and store it in a cool, dry place.

Infrared Remote Control


AV2 (SATELLITE) IN SCART (EURO-21) SOCKET #(SV-665B/SV-661B/SV-662B/SV-661I ONLY)
TUNER, AV1, AV2, AUX SELECTION / REPEAT SELECTION BUTTON
RCA AUDIO L, R OUTPUT SOCKETS #(SV-665B/SV-661B/SV-662B/SV-661I ONLY)
TUNER, AV1, AV2, AUX #(SV-661B/SV-662B/ SV-651I ONLY) SELECTION / REPEAT SELECTION BUTTON DISPLAY BUTTON PROGRAMME SELECTION BUTTON PLAY/PAUSE/STILL BUTTON
IPC BUTTON TRACKING BUTTONS AUDIO MODE SELECTION BUTTON #(SV-661B/SV-662B//SV-661I ONLY)

Deciding How to Connect Your VCR
You must take into account various factors when connecting audio or video systems:
N Types of connectors available on your systems
N Systems connected permanently to the VCR (satellite receiver for example) or temporarily
Your VCR is equipped with the following connectors.
Connector Location Type Direction Recommended Use
AV1 (EURO AV) Rear SCART In/Out N Television N Satellite receiver N Other VCR
OUT TO TV Rear 75 Ω Out N Television
1 Cassette loaded indicator 2 PLAY indicator 3 Multi-function display 4 Timer indicator 5 STEREO indicator #(SV-665B/SV-661B/SV-662B/SV-661I ONLY) 6 Rec indicator
IN FROM ANT. Rear 75 Ω In N Aerial
coaxial N Cable television network N Satellite receiver
AV2 Rear SCART In N Satellite receiver (SATELLITE) N Other VCR
AUX Front Audio/Video RCA In N Audio Hi-Fi system N Camcorder
Audio output Rear Audio RCA Out N Audio Hi-Fi system
R/D
AUDIO
L/G
You have just purchased a SAMSUNG Video Cassette Recorder (VCR). Together with your VCR, you will find the following accessories in the box.
☛ Whenever you connect an audio or video system to your VCR, ensure that all elements are switched off.
COAXIAL CABLE
Refer to the documentation supplied with your equipment for detailed connection instructions and associated safety precautions.
CLR/RST F.ADV INDEX
V-LOCK
SHUTTLE
SLOW
AUDIO
A.TRK IPC INPUT
DISPLAY
SPEED DUB TV/VCR TIMER

Connecting Your VCR to the TV using the Coaxial Cable and SCART cable
To receive television programmes a signal must be received from one of the following sources:
You can connect your VCR to a Satellite receiver or other VCR using the SCART cable if the appropriate outputs are available on the equipment chosen. The following illustrations give a few examples of the connection possibilities.
N An outdoor aerial N An indoor aerial N A cable television network N A satellite receiver ☛ Make sure that both the television and the VCR are switched off before connecting the cables.
OUT/SORTIE
R/D
Plug the SCART Cable with satellite receiver or other equipment into the AV2(SATELLITE) socket on the rear of the VCR. After making this connection, select the source by pressing the INPUT button for the AV2 input sources.
AUDIO
AV1 (EURO AV)
1 Remove the aerial or network input cable from the television.
2 Connect this cable to the 75Ωcoaxial socket marked on the rear of your VCR.
After making this connection, you must preset the station received through the satellite tuner. RF output channel of the satellite receiver should be adjusted away from channel 60, which is used by the VCR, e.g. re-adjust to channel 65.
3 Plug the coaxial cable supplied into the socket on your VCR.
TV
AV2 (SATELLITE) IN
OUT/SORTIE
4 Plug the other end of the coaxial cable into the connector previously used for the aerial on the television.
R/D
AUDIO
AV1 (EURO AV)
L/G
5 Connect one end of the scart cable to the AV1 (EURO AV) socket on the rear of the VCR. You must connect your VCR to the television via the scart cable.
Satellite Receiver or other Equipment
6 Plug the other end into the appropriate connector on the television.
R/D
TV
TV
AUDIO
AV1 (EURO AV)
L/G
AV2 (SATELLITE) IN
OUT/SORTIE
TV
R/D
L/G
AUDIO
AV1 (EURO AV)

Tuning Your Television for the VCR
You must tune your television for the VCR only if you are not using a Scart cable
You can connect your VCR to a Hi-Fi system. Example: You wish to take advantage of the quality of your Hi-Fi
stereo system when watching a programme or recording via your VCR. ☛ N Regardless of the type of connection chosen, you
➢ To view pictures from your VCR when a Scart cable is used, the television must be set to the audio/video mode (AV).
OUT/SORTIE
TV
R/D
AUDIO
must always connect the coaxial cable supplied. Otherwise, no picture will be visible on the screen when the VCR is switched off.
L/G
STANDBY/ON
VCR STANDBY/ON
1 Switch on the television.
N Make sure that both the television and the VCR are
2 Switch on the VCR by pressing STANDBY/ON on the front of the VCR or VCR STANDBY/ON (STANDBY/ON) on the remote control.
SLO
switched off before connecting the cables.
1 Connect the coaxial cable or SCART as indicated on page 12.
AV2 (SATELLITE) IN
3 Select a programme position on the television to be reserved for use with your VCR.
2 Plug the audio output cable into the audio connectors on the rear of your VCR. ➢ Respect the colour coding of the left and right channels.
4 Insert the video cassette in the VCR. Check that the VCR starts reading the cassette; if not, press ❿II button.
AUDIO
AV1 (EURO AV)
L/G
3 Plug the other end of the audio cable into the appropriate input connectors on your Hi-Fi stereo system.
5 Start a scan on your television or set the television to UHF channel 60.
6 Fine tune the television until the pictures and sound are obtained clearly.
7 If you cannot find the pictures and sound, or there is interference from nearby channels, it may be necessary to change the setting of the VCR output channel (see Setting the VCR Output Channel on page 17 and Problems and Solutions on page 49).
Your VCR will automatically set itself up when it is plugged into the mains for the first time. TV stations will be stored in memory. The process takes a few minutes. Your VCR will then be ready for use.
8 When the picture and sound are perfectly clear, store this channel at the desired programme position on the television. Result: That programme is now reserved for use with your VCR.
1 Connect the coaxial cable as indicated on page 12. (Connecting Your VCR to the TV Using the Coaxial Cable)
2 Plug the VCR into the mains. Result: A message appears.
TV
R/D
AUDIO
AV1 (EURO AV)
L/G
3 Press OK button to start the auto scanning
N The number of stations automatically stored by the VCR depends on the number of stations that it has found. N The process will finish after a few minutes.
4 The current time and date are displayed automatically. Check the date and time.
if it is : N Correct, Press MENU button twice to exit the menu. N incorrect, see page 16. ➢ Auto preset can be performed by pressing I (STOP) on the VCR continuously for 5 seconds or more with no tape inserted. ☛ Function for “Plug & Auto Set Up” is fixed already. So if you want to change this fixed one, you can change it by Presetting the Stations Automatically in OSD “ Auto Set Up” menu. (see page 18)

Displaying/Hiding On-Screen Information
You must insert or replace the batteries in the remote control when you:
Your VCR displays most information both on the VCR and the television. You can choose to display or hide this information on the television screen (except for the Index, Programming MENU and VIDEOPLUS+ functions #(SV-665B/SV-265B only), which cannot be hidden).
N Purchase the video cassette recorder

N Find that the remote control is no longer working
PTIONS OSD :ON TAPE SELECT :E180 COLOUR SYSTEM :AUTO FORMAT 16:9 :AUTO NICAM :ON ECO. MODE :OFF IPC :ON
1 Push the tab in the direction of the arrow to release the battery compartment cover on the rear of the remote control.
1 Press MENU on the remote control. Result: The programming menu is displayed.
2 Insert two AA, R6 or equivalent batteries, taking care to respect the polarities:
2 Press the corresponding ,❷or ➛, ❿buttons to select the USER SET option.
N + on the battery with + on the remote control
N – on the battery with – on the remote control
3 Press the OK button to select this option. Result: The USER SET menu is displayed.
3 Replace the cover by aligning it with the base of the remote control and pushing it back into place.
4 Press the corresponding or ❷buttons, until the OSD option is selected.
PTIONS OSD :ON TAPE SELECT :E180 COLOUR SYSTEM :AUTO ECO. MODE :OFF IPC :ON
➢ Do not mix different battery types (manganese and alkaline for example).
5 To... Press ➛or ❿, until...
Display on-screen information ON is displayed.
Hide on-screen information OFF is displayed.
6 On completion, press MENU twice to exit the menu.
Your VCR contains a 24-hour clock and calendar used to:
N Automatically stop programme recording N Preset your VCR to record a programme automatically
You must set the date and time when:
N You purchase the video cassette recorder ☛ N The time and date are set automatically from the
broadcast signal. If the signal is weak or ghosting occurs, the time and date may not be set automati- cally. In this case, they should be set manually.
Your VCR output channel may need to be changed if the pictures suffer from interference or if your TV cannot find the pictures. Also, you can change the VCR output channel to adjust the frequency in which information is displayed on the screen.

N Do not forget to reset the time when you change
clocks from winter to summer time and vice versa.
1 Press MENU on the remote control. Result: The programming menu is displayed.
1 Press MENU on the remote control. Result: The programming menu is displayed.
2 Press the corresponding , ❷or ➛, ❿buttons to select the CLOCK SET option.
2 Press the corresponding , ❷or ➛, ❿buttons to select the INSTALLATION option.
3 Press the OK button to select this option. Result: The CLOCK SET menu is displayed.
3 Press the OK button to select this option. Result: The INSTALLATION menu is displayed.
4 Press ➛or ❿to select the hour, minutes, day, month and year. Result: The option selected flashes.
INSTALL AUTO SET UP MANUAL SET UP VCR OUTPUT CH :CH60
4 Press the corresponding or ❷buttons, until the VCR OUTPUT CH option is selected.
5 Press the or ❷buttons to increase or decrease the value. Result: The day of the week is displayed automatically. ➢ You can hold the or ❷buttons down to scroll more quickly through the values.
5 Select the required output channel (CH21~CH69) by pressing the ➛or ❿buttons.
AUTO CLOCK : ON
6 On completion, press MENU twice to exit the menu. Then tune your television again (see page 15).
6 On completion, press MENU twice to exit the menu.
correctly

Presetting the Stations Manually
☛ You do not need to preset the stations if you have already set them automatically (see Plug & Auto Set Up on
☛ You do not need to preset the stations manually if you have already set them automatically.


page 14).
1 Press the MENU button on the remote control. Result: The programming menu is displayed.
Your VCR contains a built-in tuner used to receive television broadcasts.
You must preset the stations received through the tuner. This can be done:
2 Press the corresponding ,❷or ➛, ❿buttons to select the INSTALLATION option.
N Plug & Auto Set up (see page 14) N Automatically N Manually (see page 19)
3 Press the OK button to select this option. Result: The INSTALLATION menu is displayed.
4 Press the corresponding or ❷buttons, until the MANUAL SET UP option is selected.
You can store up to 80 stations.
INSTALL AUTO SET UP MANUAL SET UP VCR OUTPUT CH :CH60
1 Press the MENU button on the remote control. Result: The programming menu is displayed.
5 Press the ❿button to select a MANUAL SET UP option. Result: The TV STATION TABLE menu is displayed.
INSTALL AUTO SET UP MANUAL SET UP VCR OUTPUT CH :CH60
6 Press the or ❷buttons to select a programme number as required. 7 Press the ❿button to preset the station. Result: The MANUAL TUNING menu is displayed.
2 Press the corresponding ,❷or ➛, ❿buttons to select the INSTALLATION option.
3 Press the OK button to select this option. Result: The INSTALLATION menu is displayed.
8 Press the ➛or ❿buttons to start scanning. Result: The frequency band is scanned and the first station found is displayed.
4 Press the corresponding or ❷buttons, until the AUTO SET UP option is selected. And then press the ❿button to select this option. Result: A message appears, indicating that any channels already preset on your VCR will be deleted.
9 Press the or ❷buttons until the NAME is selected. The station name is set automatically from the broadcast signal.
PR CH NAME 1 27 CAEB 2 -- 3 -- 4 -- 5 --
10 To change the programme’s name, press the ❿button. Result: The first letter of the name flashes.
5 Press OK to start the auto scanning. Result: N The PLEASE WAIT indication flashes on the television screen.
11 To... Then...
N The first frequency band is scanned and the first station found is displayed and stored.
Select a character Press the or ❷button until the in the name required character is displayed (letters, numbers or “-” character).
N The VCR then searches for the second station and so on.
Move to the next or Press the ❿or ➛buttons previous character respectively.
N When the automatic scanning procedure has finished, the VCR switches automatically to pro- gramme 1. ➢ The number of stations automatically stored by the VCR depends on the number of stations that it has found.
12 If you... Then...
Wish to store the N Press the corresponding or ❷buttons, station displayed until the MFT is selected.
N Press the ➛or ❿buttons to adjust the
picture, if necessary.
6 If you wish to cancel the auto scanning before the end, press the MENU button three times to exit the menu. ➢ N The time and date are set automatically from the
N Press OK to store the station
Do not wish to N Press the corresponding or ❷buttons, store the station until the CH is selected. displayed N Press the ➛or ❿buttons to go on
broadcast signal. If the signal is weak or ghosting occurs, the time and date may not be set automati- cally. In this case, they should be set manually (see page 16).
scanning the frequency band and display the next station
N Go back to the beginning of Step 12
13 Repeat this procedure from Step 6 onwards, until all the required stations have been stored.
N Once the auto scanning procedure has finished, some
stations may have been stored more than once; select the stations with the best reception and delete the ones no longer required (see page 20).
14 On completion, press the MENU button three times to exit the menu.

Changing the Preset Station Table
You can rearrange the Station Table and give different programme numbers to the stations listed according to your own preferences.
If you have stored a TV station:
N That you do not require


N At the wrong programme position
1 Press the MENU button on the remote control.
you can cancel it.
2 Press the corresponding , ❷or ➛, ❿buttons to select the INSTALLATION option.
1 Press the MENU button on the remote control.
3 Press the OK button to select this option. Result: The INSTALLATION menu is displayed.
2 Press the corresponding ,❷or ➛, ❿buttons to select the INSTALLATION option.
4 Press the or ❷buttons to select MANUAL SET UP option. And then press the ❿button to select this option. Result: The TV STATION TABLE menu is displayed.
3 Press the OK button to select this option. Result: The INSTALLATION menu is displayed.
INSTALL AUTO SET UP MANUAL SET UP VCR OUTPUT CH :CH60
INSTALL AUTO SET UP MANUAL SET UP VCR OUTPUT CH :CH60
4 Press the corresponding or ❷buttons, until the MANUAL SET UP option is selected.
5 Press the corresponding or ❷buttons, until the required preset TV programme is selected. Result: The selected station is displayed at the same time on the television screen.
5 Press the ❿button to select this option. Result: The TV STATION TABLE menu is displayed.
6 To change the programme number assigned to a station press the OK button on the remote control. (For example, To move a TV station in programme 1 to programme 3)
6 Press the corresponding or ❷buttons, until the required preset TV station (PR) is selected.
7 Press the CLR/RST button.
7 Press the or ❷buttons to select required position. And then press OK again to swap the position.
PR CH NAME 1 27 CAEB 2 -- 3 -- 4 -- 5 --
8 Repeat the same procedure from Step 6 onwards until all the required stations have been cleared.
8 You can modify this station by repeating the same procedure from Step 5 onwards.
PR CH NAME 1 27 CAEB 2 -- 3 -- 4 -- 5 --
9 On completion, press the MENU button three times to exit the menu.
9 On completion, press the MENU button three times to exit the menu.
PR CH NAME 1 -- 2 -- 3 27 CAEB 4 -- 5 --


NICAM programmes are divided into 3 types. NICAM Stereo, NICAM Mono and Bilingual (transmission in another language). NICAM programmes are always accompanied by a standard mono sound broadcast and you can select the desired sound. Please refer to page 33.


1 Press MENU on the remote control. Result: The programming menu is displayed.
2 Press the corresponding ,❷or ➛, ❿buttons to select the USER SET option.
3 Press the OK button to select this option. Result: The USER SET menu is displayed.
4 Press the corresponding or ❷buttons, until the NICAM option is selected.
OSD :ON TAPE SELECT :E180 COLOUR SYSTEM :AUTO FORMAT 16:9 :AUTO NICAM :ON ECO. MODE :OFF IPC :ON
5 To... Press ➛or ❿, until...
Mono mode OFF is displayed. OFF: Only set at this position to record the
standard mono sound during a
NICAM broadcast if the stereo sound is distorted due to inferior reception conditions.
NICAM mode ON is displayed. ON: Normally set at this position.
6 On completion, press MENU twice to exit the menu.

You can record a cassette at two different speeds:

N Each cassette lasts twice as long N The recording is of a slightly lower quality
To record a cassette... Press the SPEED button on the remote control, until...

Recording a Programme with Automatic Stop
Video cassettes have a safety tab to prevent accidental erasure. When this tab has been removed, you cannot record on the tape.
This function enables you to record up to nine hours (LP) of programmes.
Your VCR stops automatically after the requested length of time.
1 If you wish to protect a cassette, break off the tab using a small screwdriver.
1 Switch on the television.
2 To re-record over a protected cassette (safety tab broken), cover the hole with adhesive tape. 1
2 To monitor the programme being recorded, select the television channel reserved for use with your VCR (or the AV input if used).
3 Insert the cassette on which the programme is to be recorded, with the window visible and the safety tab intact or the opening covered with adhesive tape. Result: The VCR is switched on automatically.
Recording a Programme Immediately
4 Select:
N The station to be recorded using the PROG/TRK ( or ❷) / PROG ( or ❷) buttons or
Before recording a programme, you must have preset the corres- ponding station (unless you are recording via an external video source). If you have not done so, refer to pages 18 and 19.
N The AV1, AV2 or AUX #(SV-665B/SV-661B/SV-662B/ SV-651I only) source using the INPUT button for a satellite tuner or external video source Result: The channel number is displayed and the programme can be seen on the television.
DISPLA
SV-661I/SV-265B/ SV-261B/SV-262B/ SV-261I)
PROG/TRK
K PROG
1 Switch on the television.
VCR INPUT
2 To monitor the programme being recorded, select the television channel reserved for use with your VCR (or the AV input if used).
5 Select the recording speed by pressing the SPEED button as many times as required (see page 22).
3 Insert the cassette on which the programme is to be recorded, with the window visible and the safety tab intact or the opening covered with adhesive tape. Result: The VCR is switched on automatically.
PROG/TRK
K PROG
6 Hold the REC button down for a while to start recording. Result: The record indicator appears on the television screen and VCR display. An index is recorded on the tape (see page 36).
4 Select:
N The station to be recorded using the PROG/TRK ( or ❷) / PROG ( or ❷) buttons or
7 Press the REC button several times to increase the recording time in:
N The AV1, AV2 or AUX #(SV-665B/SV-661B/SV-662B/ SV-661I only) source using the INPUT button for a satellite tuner or external video source Result: The station number is displayed and the programme can be seen on the television.
N 30-minute intervals up to four hours
N 1-hour intervals up to nine hours (LP) Result: The length is displayed on the television displays. The selected programme is recorded for the length of time requested. At the end of that time, the VCR stops recording automatically.
5 Select the recording speed by pressing the SPEED button as many times as required (see page 22).
8 If you wish to cancel the recording before the end, press VCR STANDBY/ON (STANDBY/ON). ☛ If the end of the tape is reached while recording:
6 Hold REC down for a while to start recording. Result: The record indicator appears on the television and VCR display. An index is recorded on the tape (see page 36).
7 To stop recording, press I once. ➢ N If your VCR ejects the cassette when you start
N The recording stops N The VCR automatically turns off
recording, check to make sure that the cassette’s safety tab is intact or that the opening (created by a broken safety tab) is covered with adhesive tape. N If you reach the end of the tape while recording, the
SET LENGTH :
PRESS REC
cassette rewinds automatically.

Modifying VIDEOPLUS+ Programming # (V-665B/SV-265B Only)
Before presetting your VCR:
If you wish to correct the programme displayed or modify certain elements, such as the recording speed, you can do so before you press MENU a second time to confirm.
N Switch on both the television and your VCR
N Check that the date and time are correct
N Insert the cassette on which the programme is to be
If you wish to... Then...
recorded (safety tab intact)
Select an input source other N Press the ➛or ❿buttons, until the PR selection flashes.
Up to six programmes can be preset.
than the tuner (AV1, AV2 or N Press the INPUT button one or more times to change the
1 Press the TIMER button. Result: The TIMER METHOD is displayed.
AUX #(SV-665B only)) input source selection.
2 Press the corresponding or ❷buttons, until the VIDEOPLUS option is selected.
3 Press the ❿button to select VIDEOPLUS. Result: A message is displayed to allow you to enter the VIDEOPLUS+ code. ☛ If all six programmes have been set, the message TIMER IS FULL is displayed. Refer to page 29 if you wish to cancel a preset recording.
STANDARD
VIDEOPLUS
Record a programme every day N Press the ➛or ❿buttons, until the DAY selection flashes.
(Monday to Sunday) at the same time N Press the or ❷buttons, until the DLY (Daily) value is
displayed.
4 Press the numeric buttons to enter the code opposite the programme that you wish to record in your television magazine. ➢ If you wish to correct the VIDEOPLUS+ code that you are entering:
Record a programme every week N Press the ➛or ❿buttons, until the DAY selection flashes.
on the same day and at the same time N Press the or ❷buttons, until the W- (Week) value is
displayed, followed by the required day. Example: W-SA (Weekly Saturday)
N Press the ➛button until the digit to be corrected is cleared
Extend the recording time N Press the ➛or ❿buttons, until the STOP selection flashes.
N Enter the correct digit
N Press the or ❷buttons to increase or decrease the stop
5 Press the MENU button. Result: The information concerning the programme is displayed. ☛ When using the VIDEOPLUS+ function for the first time with stored stations, the programme number flashes. This one time, you must enter the station number manually by pressing the or ❷buttons. Refer to the following page if:
time.
Select the recording speed N Press the ➛or ❿buttons, until the recording speed selection
flashes. N Press the or ❷buttons until the correct indication is
PROG 1/JAN WED 21:28 PR DAY START→ STOP V/P 1 WE 1 12:00→ 12:50SP ON -- --:--→--: - -- --:--→--: - -- --:--→--: - -- --:--→--: - -- --:--→--: - ❷➛❿ DELETE:CLR/RST MENU
N The programme number or times flash
N You wish to modify the programme
6 If the programme and times are correct, press the MENU button.
Select the PDC recording N Press the ➛or ❿buttons, until the V/P selection flashes.
7 Press the VCR STANDBY/ON (STANDBY/ON) button to activate the timer.
N Press the or ❷buttons until the “ON” indication is displayed. ☛Do not select PDC unless you are sure the programme you wish to record is broadcast with PDC. If you do set PDC ON (by selecting “ON” in the right - hand column on the screen), then you must set up the start-time EXACTLY according to the published TV schedule. Otherwise the timer recording won’t take place.
8 Refer to page 29 if you wish to: N Check that your VCR has been programmed correctly N Cancel a preset recording ☛ The numbers next to each TV programme listing are VIDEOPLUS+ code numbers, which allow you to programme your videorecorder instantly with the remote control. Tap in the VIDEOPLUS+ code for the programme you wish to record.

™VIDEOPLUS+ is a trademark of Gemstar Development Corporation. The VIDEOPLUS+
system is manufactured under licence from Gemstar Development Corporation.

Checking a Preset Recording
The Timer Programming feature allows you to preset the VCR to record a programme up to one month before that programme is to be broadcast. Up to six programmes can be preset.
You can check your preset recordings:
N When you have finished presetting the VCR
☛ Before presetting a recording, check that the date and time are correct.
N If you have forgotten which programmes will be
STANDARD
PROG 1/JAN WED 21:28 PR DAY START→ STOP V/P 1 WE 1 12:00→ 12:50SP ON -- --:--→--: - -- --:--→--: - -- --:--→--: - -- --:--→--: - -- --:--→--: - ❷ SET:❿ DELETE:CLR/RST MENU
Press the or ❷buttons to select the STANDARD option and then press the ❿button or, N Press MENU on the remote control.
Press the or ❷buttons to select the STANDARD option and then press the ❿button or, N Press MENU on the remote control.
Result: The programming menu is displayed. N Press the OK button to select TIMER PROGRAMMING option.
Result: The programming menu is displayed. N Press the OK button to select TIMER PROGRAMMING option.
Result: The TIMER PROGRAMMING menu is displayed.
Result: The TIMER PROGRAMMING menu is displayed.
2 Press the or ❷buttons to select the required programme.
2 Press ❿to select the input source.
3 Select the required station by pressing the , ❷buttons or INPUT to select the AV1, AV2 or AUX #(SV-665B/SV-661B/SV-662B/ SV-661I only) input sources.
3 Press the ➛or ❿buttons to select and change any values as required. For more details, refer to the previous page.
4 On completion, press MENU twice.
4 Press ❿to select the recording day.
5 Select the required day by pressing the or ❷buttons.
6 Press ❿to select the recording start time.
7 Select the required hour value by pressing the or ❷buttons. 8 Press ❿to select the minutes.
PROG 1/JAN WED 21:28 PR DAY START→ STOP V/P 1 WE 1 12:00→ 12:50SP ON -- --:--→--: - -- --:--→--: - -- --:--→--: - -- --:--→--: - -- --:--→--: - ❷➛❿ DELETE:CLR/RST MENU
9 Select the required minute value by pressing the or ❷buttons.
10 Press ❿to select the recording end time.
11 Select the required recording end time by pressing the or ❷ buttons, following the same procedure as when selecting the recording start time.
You can cancel any programmes that are:

12 Press ❿to select the recording speed.
PROG 1/JAN WED 21:28 PR DAY START→ STOP V/P 1 WE 1 12:00→ 12:50SP ON -- --:--→--: - -- --:--→--: - -- --:--→--: - -- --:--→--: - -- --:--→--: - ❷ SET:❿ DELETE:CLR/RST MENU
N No longer required
13 Press the or ❷buttons to select the SP (Standard Play), LP (Long Play), AUTO (Auto Tape Speed Select) recording speeds.
Press the or ❷buttons to select the STANDARD option and then press the ❿button or, N Press MENU on the remote control.
14 Press ❿to select the PDC recording mode.
STANDBY/ON
15 Press the or ❷buttons to toggle between the PDC mode (marked ON) and the non-PDC mode (marked -).
Result: The programming menu is displayed. N Press the OK button to select TIMER PROGRAMMING option.
S
16 When you have finished, press the MENU button.
Result: The TIMER PROGRAMMING menu is displayed.
17 Press the VCR STANDBY/ON (STANDBY/ON) button to activate the timer. Result: Before starting recording, the VCR compares the timer duration with the remaining time on the cassette. ➢ Auto Tape Speed Select. The VCR’s “Auto Tape Speed Select” function compares the duration of the timer recording to the actual recording time remaining on the tape loaded. If there is insufficient tape to complete a timer recording in AUTO mode, the VCR automatically switches to LP mode to record the whole programme.
2 Select the programme to be cancelled by pressing the or ❷ buttons.
SH
3 Press the CLR/RST button to cancel the selected programme. Result: All the recording information is deleted and the broad- cast will not be recorded.
4 On completion, press MENU twice.
recorded · N Incorrect

Intelligent Picture Control
The Intelligent Picture Control Feature allows you to adjust the sharpness of the image automatically, according to your own preferences.
This function allows you to play back any pre-recorded cassette.
1 Switch on both the television and your VCR.
1 During playback, press the MENU button on the remote control. Result: The programming menu is displayed.
2 Insert the video cassette to be played. If the safety tab on the cassette is intact, press ❿ll.
PTIONS OSD :ON TAPE SELECT :E180 COLOUR SYSTEM :AUTO FORMAT 16:9 :AUTO NICAM :ON ECO. MODE :OFF IPC :ON
2 Press the corresponding ,❷or ➛, ❿buttons to select the USER SET option.
Otherwise, the cassette is played automatically. ➢ When a cassette is loaded, the tape position is optimized automatically to reduce disturbance (Digital Auto Tracking). When playing a cassette, if the end of the tape is reached, the cassette is rewound automatically. NTSC tapes can be played back but cannot be recorded with this VCR.
3 Press the OK button to select this option. Result: The USER SET menu is displayed.
4 Press the corresponding or ❷buttons, until the IPC option is selected.
5 Press the ❿button to select the IPC (intelligent picture control) option. ➢ When intelligent picture control mode is ON, the sharpness of the image is adjusted automatically.
3 To... Then press...
Stop the playback I (STOP).
PTIONS OSD :ON TAPE SELECT :E180 COLOUR SYSTEM :AUTO ECO. MODE :OFF IPC :ON
Eject the cassette (EJECT).
6 To adjust the sharpness manually, select Intelligent Picture Control mode OFF.
7 Press the ➛or ❿buttons until the picture is displayed according to your preferences. ➢ If you do not press a button within ten seconds, the PICTURE menu disappears automatically.

8 On completion, press the MENU button again.
The Picture Alignment feature enables you to optimize the tape position automatically to obtain the best possible picture.
When noise bars or streaks appear during playback, adjust picture alignment by pressing the A.TRK button.
N The tracking bar disappears when digital auto tracking has
1 During playback, press the IPC button.
Result: The PICTURE menu is displayed.
2 Press the ❷button to turn the IPC (Intelligent Picture Control) option ON and OFF. ➢ When Intelligent Picture Control mode is ON, the sharpness of the image is adjusted automatically.
AUDIO DISPLAY
3 To adjust the sharpness manually, press the ❷button to turn the IPC mode OFF. N The horizontal picture adjusting appears.
The Picture Adjustment feature allows you to adjust the alignment manually to obtain the best possible picture.
4 Press the ➛or ❿buttons until the picture is displayed according to your preferences. ➢ If you do not press a button within ten seconds, the PICTURE menu disappears automatically.
When noise bars or streaks appear during playback, adjust alignment manually by pressing the PROG/TRK ( or ❷) / TRK ( or ) buttons until the picture is clear and stable.
SOFTEN SHARPEN
5 On completion, press the IPC button again.
N The tracking bar disappears when you release the button.
*

Selecting the Audio Output Mode # (SV-665B/SV-661B/ SV-662B/SV-661I Only)
Your VCR can automatically play Wide Screen format prerecorded tapes. It can also record Wide Screen format programmes received from sources such as a satellite receiver.
When monitoring a TV programme or playing back a Hi-Fi recorded video tape, press the AUDIO button to select a desired sound output. As the AUDIO button is pressed, the sound output and the indicator change as below:
☛ Connect equipment compatible with Wide Screen to the VCR using the 21 pin SCART cable.
AUDIO DISP./
1 Press MENU on the remote control. Result: The programming menu is displayed.
Stereo sound Bilingual sound
2 Press the corresponding ,❷or ➛, ❿buttons to select the USER SET option. 3 Press the OK button to select this option. Result: The USER SET menu is displayed. 4 Press the corresponding or ❷buttons, until the FORMAT 16:9 option is selected.
Channel I (MAIN) heard from the left speaker, channel II (SUB) heard from the right speaker.
Heard in stereo. (left channel and right channel)
Heard in monaural.
5 Press the ❿button to select AUTO ➝ ON ➝ OFF.
Left channel heard from both the left and right speakers.
Channel I (MAIN) heard from both the left and the right speakers.
OSD :ON TAPE SELECT :E180 COLOUR SYSTEM :AUTO FORMAT 16:9 :AUTO NICAM :ON ECO. MODE :OFF IPC :ON
AUTO Set when you use a wide TV. The VCR automatically detects if programmes being played back or recorded are in normal or Wide Screen format.
Heard in monaural.
ON The VCR always plays back and records in 16:9 Wide Screen format. Set if the VCR cannot detect Wide Screen TV programmes with “AUTO” set.
Channel II-(SUB) heard from both the left and the right speakers.
Right channel heard from both the left and right speakers.
Heard in monaural.
OFF Set if you do not use a Wide Screen TV.
6 On completion, press MENU twice to exit the menu.
Sound mixed the left and right channels, and the normal audio track.
Channel I (MAIN) heard from both the left and the right speakers.
Heard in monaural.
Heard in monaural.
Before recording or playing back a cassette, you can select the required system standard. Otherwise, the system automatically selects the reception standard when you select AUTO. ➢N When playing back a cassette, the standard is automatically selected by the VCR. N When you playback an NTSC-recorded tape on this VCR make a setting on the colour system according to your TV. If your TV is a PAL system only TV, set NTPB. If your TV is Multi System TV (NTSC 4.43 compatible), set NT4.43 and you can record NT4.43.
Selecting the Audio Mute Mode # (SV-265B/SV-261B/ SV-262B/SV-261I Only)
PTIONS OSD :ON TAPE SELECT :E180 COLOUR SYSTEM :AUTO FORMAT 16:9 :AUTO NICAM :ON ECO. MODE :OFF IPC :ON

1 Press MENU on the remote control. Result: The programming menu is displayed.
To select the audio mute mode on and off, simply press the AUDIO button on the remote control.
# (SV-265B/SV-261B/SV-262B/SV-261I)
2 Press the corresponding ,❷or ➛, ❿buttons to select the USER SET option.
3 Press the OK button to select this option. Result: The USER SET menu is displayed.
PTIONS OSD :ON TAPE SELECT :E180 COLOUR SYSTEM :AUTO ECO. MODE :OFF IPC :ON
4 Press the corresponding or ❷buttons, until the COLOUR SYSTEM option is selected.
5 Press the ❿button to select AUTO ➝ PAL ➝ B/W.
AUTO When playing back a cassette, the system standard is
automatically selected by the VCR. B/W Black and White
6 On completion, press MENU twice to exit the menu.


Playing a Sequence Frame by Frame

➢ No sound is heard when playing back a cassette in slow motion.
N Stop the cassette at a given frame (image) N Advance one frame at a time ➢ No sound is heard when playing back frame by frame.
N SLOW ( ) as many times as required to decrease or increase the speed respectively
N ❿ll to stop the tape at a given frame
N To return to the normal speed, press the ❿ll button twice.
N F.ADV ( ) to advance frame by frame
2 To return to normal playback, press ❿ll. ☛ When you have been using the Frame-by-Frame function for more than about five minutes, the VCR will auto- matically play to protect the cassette and video heads. ➢ Vertical stability: When playing back frame by frame, interference may be seen on the screen. Press the V-LOCK ( ) buttons to minimize this effect.
2 When playing back in slow motion, picture interference may occur. Press the PROG/TRK ( or ❷) / TRK ( or ) buttons to minimize this effect. ☛ When you have been using the Slow Motion function for more than about five minutes, the VCR will automatically play to protect the:
Picture Search enables you to Fast Forward or Rewind and look for a particular part of a tape.
1 Press PLAY, the VCR will enter normal play mode. While in play, press and release the ❿❿(or ➛➛) button. The VCR will search at 5 times the normal playback speed.
2 To return to normal playback mode, press the ❿II button.
3 If you press and HOLD down the ❿❿(or ➛➛) button the VCR will search at 9 times the normal speed. Releasing the ❿❿button will return the VCR to search at 5 times the normal speed. To return to normal playback mode, press the ❿II button.
4 Whilst in Picture Search mode, if you press the ❿❿button again, the VCR will enter normal Fast Forward mode.
5 Likewise, whilst in Picture Search ➛➛mode, if you press the ➛➛ button again, the VCR will enter normal Rewind mode.
6 If, when Rewinding (➛➛) or Fast Forwarding (❿❿), you press the ➛➛ (or ❿❿) button, the VCR will enter the Picture Search mode.

Auto Repeat Play
You can set repeat play to repeat the tape continuously from beginning to end.
Each time you record a cassette on this VCR, an “index” is automatically marked on the tape when recording starts.

The Search function allows you to fast-forward or rewind to a specific index and start playback from that point. Depending on the direction selected, the indexes are numbered as follows:
1 Press MENU on the remote control. Result: The programming menu is displayed.
VIDEOPLUS EXTEND :OFF AUTO POWER OFF :OFF REPEAT PLAY :OFF NO. OF
2 Press the corresponding ,❷or ➛, ❿buttons to select the EASY OPERATION option.
Seq. being
3 Press the OK button to select this option. Result: The EASY OPERATION menu is displayed.
etc.
Seq.
Seq. etc.
2 1 1 2
4 Press the corresponding or ❷buttons, until the REPEAT PLAY option is selected.
➢ This VCR uses a standard indexing system (VISS). As a result, it will recognize any indexes marked by other VCRs using the same system and vice versa.
5 To... Press ➛or ❿, until...
AUTO POWER OFF :OFF REPEAT PLAY :OFF NO. OF
Repeat play ON is displayed.
Do not wish to repeat play OFF is displayed.
1 To search for a specific index, press INDEX.
6 On completion, press MENU twice to exit the menu.
2 Press the ➛➛or ❿❿buttons depending on the direction where your desired programme is located.
3 When an Index mark is found the VCR will playback the tape for 5 seconds, after which it will continue searching for the next Index mark.
4 If you want to watch the tape from a particular Index, simply press ❿II.
You can set Interval Repeat Play so that the cassette is repeated a number of times according to a specified set interval.
1 Press MENU on the remote control. Result: The programming menu is displayed.
Index Skip Search: This feature will enable you to fast forward/rewind to a specific point on a tape: E.g. if you have recorded 3 different programmes on a tape and you have rewound the tape to the beginning, by using this feature you can go directly to the start of programme 2 simply by pressing the INDEX button.
2 Press the corresponding ,❷or ➛, ❿buttons to select the EASY OPERATION option.
3 Press the OK button to select this option. Result: The EASY OPERATION menu is displayed.
1 Press the INDEX to start the Index search.
4 Press the corresponding or ❷buttons, until the NO. OF INTERVAL REPEAT option is selected.
VIDEOPLUS EXTEND :OFF AUTO POWER OFF :OFF REPEAT PLAY :OFF NO. OF
2 Press the ➛➛or ❿❿buttons twice more. This will take you directly to the start of the desired programme is located.
5 To... Press ❿, until...
Interval Repeat Play 5, 10, 15 is displayed. (choose an interval repeat of 5, 10 or 15 times)
3 These Index searches can be made forwards: (press ❿❿) or backwards: (press ➛➛).
4 To cancel an Index search simply press the ❿II or I button.
Cancel Interval Repeat Play OFF is displayed.
6 On completion, press MENU twice to exit the menu.
SV-262B/SV-261I)
7 To select Interval Repeat Play during playback, press the INPUT/REPEAT button at the desired start point. Result: “INTERVAL REPEAT SETTING” is displayed. Press the INPUT/REPEAT button one more time at the desired end point. Result: The tape is automatically rewound to the start point. “INTERVAL REPEAT” is displayed.
AUTO POWER OFF :OFF REPEAT PLAY :OFF NO. OF
INTERVAL REPEAT : 5

Connecting an RCA Audio/Video Input Cable # (SV-665B/SV-661B/SV-662B/SV-661I Only)
To prevent delays or over-runs the VCR has a function called Videoplus EXTEND allowing you to extend the recording time by up to 60 minutes.
You can connect other audio/video equipment to your VCR using audio/video cables if the appropriate outputs are available on the equipment chosen.
➢ Only use if PDC is not available or set to OFF.
1 Press the MENU button on the remote control.
second VCR (see page 40). N You wish to play back and/or copy pictures taken
STANDBY/ON
EJECT
EJECT
2 Press the corresponding ,❷or ➛, ❿buttons to select the EASY OPERATION option.
with a camcorder (see page 40). ☛ N Regardless of the type of connection chosen, you
VIDEO L AUDIO R
AUX
AUX
3 Press the OK button to select this option. Result: The EASY OPERATION menu is displayed.
must always connect the coaxial cable supplied. Otherwise, no picture will be visible on the screen when the VCR is switched off.
4 Press the corresponding or ❷buttons, until the VIDEOPLUS EXTEND option is selected.
PDC/VPS DEFAULT :OFF VIDEOPLUS EXTEND :OFF AUTO POWER OFF :OFF REPEAT PLAY :OFF NO. OF
N Make sure that both the television and the VCR are
5 Press ➛or ❿buttons to set the Videoplus EXTEND time by increments of 10 minutes.
switched off before connecting the cables.
6 To turn off, press ➛or ❿buttons repeatedly until OFF shows.
1 Connect one end of the RCA audio/video cable into the VIDEO INPUT socket on the front of the VCR.
2 Plug the other end of the audio/video cable into the appropriate output connector on the other system (VCR or camcorder).
3 Connect one end of the RCA audio cable supplied into the AUDIO INPUT sockets on the front of the VCR. ➢ Take care to respect the colour coding of the left and right channels.
The tape counter:
N Indicates the elapsed time in the play and record modes
(hours, minutes and seconds) N Is reset when a cassette is inserted in the VCR
4 Plug the other end of the audio cable into the appropriate output connectors on the other system (VCR, camcorder or Hi-Fi sound system).
N Allows you to find the beginning of a sequence easily ☛ If the remaining time is to be calculated correctly, you must indicate the type of cassette being used.
0:00:00
1 Insert a cassette in your VCR.
2 To set the tape counter to zero at the beginning of a sequence: N Press DISP./ or DISPLAY twice to display the counter N Press CLR/RST when you want to set the tape counter to zero 3 When you are ready, N Start playback or Recording. N Press the I button. N To fast-forward or rewind to the sequence at which the counter was set to zero, press ➛➛or ❿❿. ➢ Some VCR information, such as the counter, can be displayed on the television screen (unless you have deactivated the OSD mode; refer to page 17).
CLR/RST F.ADV INDEX
CLR/RST F.ADV INDEX
TV VCR INPUT
SELECT
A.TRK IPC INPUT
UDIO
DISP./
DIO
DISPLAY
VOL PROG/TRK
Press DISP./ or DISPLAY:
N Once to display the current function, programme number, recording speed, date, time and counter
N Twice to display the counter only
N Three times to display the time remaining on the cassette
N Four times to clear the display
-/--

Using the Assemble Edit Function
This function allows you to start a new recording at a specific position on the cassette while maintaining a very smooth scene change.
Your VCR remote control will work with Samsung televisions and compatible brands.
1 Insert the cassette to be edited in your VCR.

To determine whether your television is compatible, follow the instructions below.
2 Press the ❿ll button to start playback.
3 When you reach the position from which you wish to start the new recording, press the ❿ll button.
1 Switch your television on.
4 Press the F.ADV ( ) button again as often as necessary to advance frame by frame, until the exact recording position is located.
2 Point the remote control towards the television.
3 Hold down the TV button and enter the two-figure code corresponding to the brand of your television, by pressing the appropriate numeric buttons.
5 While the VCR is in still mode, hold the REC button down for a while to activate the Assemble Edit function. Result: Record symbol flashes in the display.
Brand Codes Brand Codes
6 Select the source from which you wish to record by pressing:
N The PROG/TRK ( or ❷) / PROG ( or ❷) buttons for television channels
SAMSUNG 01 to 06 PHILIPS 02, 20, 22 AKAI 09, 23 SABA 13, 14, 22 to 24 GRUNDIG 09, 17, 21 SONY 15, 16 LOEWE 02 THOMSON 13, 14, 24 PANASONIC 08, 23 to 27 TOSHIBA 07, 16 to 19, 21
N The INPUT button for the AV1, AV2 or AUX# (SV-665B/ SV-661B/SV-662B/SV-661I only) input sources
7 Press the ❿ll button to start recording.
8 When you have finished recording, press I .
Result: If your television is compatible with the remote control, it is switched off. It is now programmed to operate with the remote control. ➢ If several codes are indicated for your television brand, try each one in turn until you find one that works. ☛ When you change the batteries in the remote control, you must reprogramme the code, following the same procedure.
You can copy a cassette to your VCR from another video source, such as another VCR or a camcorder.
☛ It is an infringement of copyright laws to copy prerecorded cassettes or to re-record them in any form without the permission of the owners of the corresponding copyright.
You can then control the television using the following buttons.

1 Connect the VCR, from which the cassette is to be copied, to the appropriate SCART audio and video input connectors on the rear of your VCR. You can also use a RCA audio and video cable to connect the AUX input on the front of your VCR. #(SV-665B/SV-661B/SV-662B/ SV-661I only) 2 Insert a blank cassette in your VCR. 3 Insert the pre-recorded cassette in the other video source (VCR or camcorder). 4 Press the INPUT button to select the appropriate input on your VCR: N AV1 or AV2 #(SV-665B/SV-661B/SV-662B/SV-661I only) for the SCART input N AUX for the RCA input #(SV-665B/SV-661B/SV-662B/ SV-661I only)
TV STANDBY/ON ➀ Used to switch the television on and off.
TV or VCR ➁ Used to switch between the TV and VCR modes. Only the VOL (+ or – ) and TV STANDBY/ON buttons are operational in VCR mode.
-/-- ➂ Used to enter a two-figure programme number. Example: For programme 12, press -/-- followed by numeric buttons 1 and 2.
INPUT ➃ Used to select an external source.
VOL + or – ➄ Used to adjust the volume of the television.
PROG/TRK ➅ Used to select the required programme. (or❷)
5 Start playing back the cassette to be copied. 6 Hold REC down for a while to start recording on your VCR. 7 When you have finished recording, press I on both VCRs. ➢ If you wish to view the cassette being copied:
DISP./ ➆ Used to switch between an external source and the television tuner. ➢ The various functions will not necessarily work on all televisions. If you encounter problems, operate the television directly.
N Your VCR must be connected as usual to the television (see page 12 for further details)
Button Function

Technical Specifications
The Auto Power Off feature automatically turns off your VCR if no signal is received and you do not press any button for the selected time.
Design and specifications are subject to change without notice.
VIDEOPLUS EXTEND :OFF AUTO POWER OFF :OFF REPEAT PLAY :OFF NO. OF
1 Press MENU on the remote control. Result: The programming menu is displayed.
INTERVAL REPEAT : 5
2 Press the corresponding ,❷or ➛, ❿buttons to select the EASY OPERATION option.
Format VHS PAL standard VHS PAL standard Heads Video: 4 rotary heads Video: 2 rotary heads Hi-Fi audio: 2 rotary heads Audio/Control: 1 stationary head Audio/Control: 1 stationary head Erase: 1 full track erase head Erase: 1 full track erase head Receiving channel UHF (SV-665B/SV-661B/SV-662B) UHF (SV-265B/SV-261B/SV-262B) VHF-I, VHF-III, UHF, (SV-661I) VHF-I, VHF-III, UHF,(SV-261I) lnterband/Hyperband lnterband/Hyperband Television system STANDARD I STANDARD I Luminance FM azimuth recording FM azimuth recording Colour system PAL/NT4.43: Down PAL/NT4.43: Down converted subcarrier phase shifted converted subcarrier phase shifted direct recording direct recording NTSC PB on PAL TV NTSC PB on PAL TV Tape speed SP 23.39 mm/sec SP 23.39 mm/sec LP 11.69 mm/sec LP 11.69 mm/sec Recording/playback time SP 3 hours (E-180 Tape) SP 3 hours (E-180 Tape) LP 6 hours (E-180 Tape) LP 6 hours (E-180 Tape) REW time About 60 sec in REW with E-180 About 60 sec in REW with E-180
3 Press the OK button to select this option. Result: The EASY OPERATION menu is displayed.
SV-262B/SV-261I)
4 Press the corresponding or ❷buttons, until the AUTO POWER OFF option is selected.
AUTO POWER OFF :OFF REPEAT PLAY :OFF NO. OF
5 Press the ❿button, until you select the time of Auto Power off interval.
OFF 2HOUR 3HOUR
6 On completion, press MENU twice to exit the menu.
VIDEO Input 0.5 to 2.0 Vp-p; 75 ohm unbalanced 0.5 to 2.0 Vp-p; 75 ohm unbalanced Output 1.0 ± 0.2 Vp-p; 75 ohm unbalanced 1.0 ± 0.2 Vp-p; 75 ohm unbalanced Signal-to-noise ratio Better than 43 dB (SP) Better than 43 dB (SP) Horizontal resolution More than 240 lines More than 240 lines
With this mechanism you can prevent children from harming themselves or the VCR. It stops fingers and small articles from entering your VCR.
AUDIO Input -8 dBm, 47 Kohm unbalanced -8 dBm, 47 Kohm unbalanced Output -8 ± 3 dBm, 1 Kohm unbalanced -8 ± 3 dBm, 1 Kohm unbalanced Wow and flutter (WTD) 0.4% max (SP) 0.4% max (SP) Signal-to-noise ratio 68 dB min (IHF A filter) 42 dB min (IHF A filter) Frequency response 20Hz - 20kHz 100Hz - 8kHz
Low Power Mode reduces the Standby power consumption of the VCR when in Standby mode. Useful, for example, when you are away from the house on holiday. It saves actually turning the VCR off.
PTIONS OSD :ON TAPE SELECT :E180 COLOUR SYSTEM :AUTO FORMAT 16:9 :AUTO NICAM :ON ECO. MODE :OFF IPC :ON
Power requirement 220-240V~, 50 Hz 220-240V~, 50 Hz Power consumption Approx. 17 watts Approx. 15 watts Operation temperature 41°F-104°F (5°C-40°C) 41°F-104°F (5°C-40°C) Operation humidity 10%-75% 10%-75% Weight 2.8 Kg (net) 2.8 Kg (net) Dimensions (WxHxD) 360 x 94 x 240 mm 360 x 94 x 240 mm
1 Press MENU on the remote control. Result: The programming menu is displayed.
2 Press the corresponding ,❷or ➛, ❿buttons to select the USER SET option. 3 Press the OK button to select this option. Result: The USER SET menu is displayed.
4 Press the corresponding or ❷buttons, until the ECO. MODE is selected. 5 Press the ❿button to turn LOW(3Watts) mode on. Now, when the VCR is standby mode the front display panel will shut off. Even the clock disappears. By pressing the VCR STANDBY/ON (STANDBY/ON) button again the display panel will reappear.
PTIONS OSD :ON TAPE SELECT :E180 COLOUR SYSTEM :AUTO ECO. MODE :OFF IPC :ON
6 On completion, press MENU twice to exit the menu.

Problems and Solutions
AUTHORISED SERVICE CENTERS
In the event of warranty service being required, please contact your retailer first. If they cannot provide service, please contact your nearest service centre listed below. Service facilities are return to base, however some agents may provide an in-home service (there may be a cost for call out). Please refer to your warranty card or retailer for terms and conditions of the warranty.
Before contacting the Samsung after-sales service, perform the following simple checks.
ESSEX
LONDON
WEST MIDLANDS
BRISTOL GOGGLEBOX TV TEL: 01275 838083
WICKFORD CENTRAL SERVICE TEL: 01268 766333
WILLESDEN ATLANTIC ELECTRIC TEL: 0181 451 6155
DUDLEY J S STOREY ELECTRICAL TEL: 01384 455608 WALSALL BEAVER ELECTRONICS TEL: 01922 725554 WARLEY MERRIVALE TV SVCS TEL: 0121 544 6273/6350
No power N Check that the power plug is connected to a wall outlet.
N Have you pressed the VCR STANDBY/ON (STANDBY/ON)
BRIDGEND BRIDGEND SERVICE TEL: 01656 663463
MANCHESTER
READING A & W SOUND & VISION TEL: 01734 872000 MAIDENHEAD J F ASSOCIATES TEL: 01628 25709 WARGRAVE J F ASSOCIATES TEL: 01734 401525
ASHTON UNDER LYNE VIDEOTECH UK TEL: 0161 308 4092 NORTHENDEN G H SUMNER LTD TEL: 0161 998 2705
You cannot insert a video cassette N A video cassette can only be inserted with the window
side up and the safety tab facing you.
MERSEYSIDE
The television programme was not recorded N Check the VCR aerial connections.
ELLESMERE PORT H & H VIDEO & TV TEL: 0151 357 1011 LIVERPOOL P & A AUDIO VIDEO LTD TEL: 0151 924 7287
N Is the VCR tuner properly set?
WORCESTERSHIRE
N Check if the safety tab is intact on the cassette.
WORCESTER THE HI FI CAR RADIO REPAIR TEL: 01905 26623
FAREHAM SOUND & VISION TEL: 01329 286551 FARNBOROUGH ICTV TEL: 01252 510118 PORTSMOUTH ICTV TEL: 01705 653654 SOUTHAMPTON OLYMPIC TV & AUDIO TEL: 01703 703401
Timer recording was unsuccessful N Was the VCR STANDBY/ON (STANDBY/ON) button pressed
to activate the timer?
HAYES A & A REPAIRS TEL: 0181 561 2900/4104
N Re-check the recording start/stop time settings.
N If there was a power failure or interruption during timer
CHESTER H & H VIDEO & TV TEL: 01244 379579 WARRINGTON W L ELECTRONICS TEL: 01925 764387
recording, the recording will have been cancelled.
No playback picture or the picture N Check to see if you are using a prerecorded tape. is distorted
YORK DBS SERVICE CENTRE TEL: 01904 789789
HEREFORD
CORNWALL
HEREFORD J P MICRO SVCS TEL: 01432 356353
You cannot see normal broadcasts N Check the TUNER/EXTERNAL setting. It should be on
BUDE H B H WOOLACOTTS TEL: 01288 352269 LAUNCESTON H B H WOOLACOTTS TEL: 01566 772096 NEWQUAY GREENBANK ELECTRONICS TEL: 01637 880576 WADEBRIDGE H B H WOOLACOTTS TEL: 01208 816155
TUNER.
WEST YORKSHIRE
N Check the TV/VCR aerial connections.
Noise bars or streaks on playback N Press the PROG/TRK ( or ❷) / TRK ( or ) buttons to minimize this effect.
When the ❿II button is pressed N A still picture may have “noise bars”, depending on the condition during playback, the still picture of the tape. Press the PROG/TRK ( or ❷) /TRK ( or ) has severe “noise bars” streaks buttons during SLOW motion to minimize this effect.
GOOLE HEADLAND ELECTRCS TEL: 01977 661223
CHANNEL ISLANDS
CUMBRIA
SHROPSHIRE
GUERNSEY TELESKILL LTD TEL: 01481 56508 JERSEY ALTERNATIVE ELECT TEL: 01534 68277 ISLE OF WIGHT AUDIO VISION SVCS TEL: 01983 752023
BARROW IN FURNESS KENNETH GARDNER TEL: 01229 821202 SEARLE AUDIO TEL: 01229 839692 PENRITH CANNAN & BROWN TEL: 01768 864829
SOUTH HUMBERSIDE
Video Head Cleaning N If poor pictures appear on a variety of cassettes, the video
heads may need cleaning. This is not a common problem and unless it appears, the heads should not be cleaned. When cleaning the video heads, read all instructions provided with the head cleaning cassette. Incorrect head cleaning can permanently damage the video heads.
CANTERBURY BARRETTS OF CANTERBURY TEL: 01227 766582 DARTFORD BUDGET REPAIR CENTRE TEL: 01322 227668 MAIDSTONE AVERY ELECTRONICS TEL: 01622 682138
NORTHERN IRELAND
HOLSWORTHY H B H WOOLACOTTS TEL: 01409 253280 NEWTON ABBOT TELLI-SCOPE ELECTRONICS TEL: 01626 63907 PLYMOUTH ARGYLE TV & VIDEO TEL: 01752 779933 CTV ELECTRONICS TEL: 01752 350950
STAFFORDSHIRE
If when tuning in your TV to the VCR test 1. Remove the aerial input plug from the socket marked (aerial pattern your TV does not find the test pattern symbol) on the rear of the VCR. or the pattern when found suffers from 2. Carry out the instructions “Tuning Your Television for the VCR” interference, it may be due to the VCR output (see page 15). channel clashing with the normal TV 3. Carry out the instructions “Setting the VCR output Channel” transmissions in your area. To prevent this (see page 17), move the channel number several channels you will need to change the VCR output down from the original setting. (example: from 60 to 57). channel in the following way 4. Replace the aerial plug into the socket marked (aerial symbol) on the rear of the VCR. 5. Re-tune your TV to the VCR again by following instructions “Tuning Your Television for the VCR” (page 15). 6. If the problem still exists repeat steps 1 to 5 moving several more channels away from the original setting.
STOKE ON TRENT TELEFAULTS (S.O.T.) LTD TEL: 01782 813757
LANCASHIRE
CO CORK TVAE REPAIRS TEL: 00353 21 273457
IPSWICH GGN LTD TEL: 01473 744300
GRAMPIANS
FRASERBURGH RODGERS ELECTRICAL TEL: 01346 518540
SURREY
DORSET
HIGHLANDS
ULLAPOOL R & R ELECTRONICS TEL: 01854 612608
DURHAM
LEICESTERSHIRE
EAST SUSSEX
LOTHIAN
SEAFORD CLEARVIEW RENTAL & RELAY TEL: 01323 898989 EASTBOURNE STARTEC SVCS TEL: 01323 412012
EDINBURGH RETEC AUDIO & VISUAL TEL: 0131 478 7779
BRANSTON STUART WALLACE TEL: 01522 791496
If you are unable to solve the problem after reading the above instructions, note:
DYFED
GLASGOW DSC ELECTRONICS TEL: 0141 941 3711
N The model and serial number on the rear of your VCR
TYNE & WEAR
HIGH HOLBORN BERRYS OF HOLBORN TEL: 0171 405 1157
NEWCASTLE UPON TYNE M SINGH RADIO & TV TEL: 0191 226 0446
N The warranty information
DUNDEE ANCRUM ELECTRONICS TEL: 01382 454511
N A clear description of the problem
Then contact your nearest SAMSUNG after-sales service.
COVENTRY D & J HENRY TEL: 01203 431393
BRAINTREE GWYNNE TV & ELECTRICAL TEL: 01376 322567
Problem Explanation/Solution · button?

c) Misuse, including the faiure to use this product for its normal
War, Public Disturbances, incorrect mains voltage, improper
force in any Country other than the one for which the product
was originally designed and manufactured. This warranty will
warranty. Unless there is national legislation to the contrary,
the rights under this warranty are the consumers sole rights
conform to national or local technical or safety standards in
d) Damage caused by Lightning, Water, Fire, Acts of God,
and Samsung, its subsidiaries and distributors shall not be
records, compact discs, videos or audio taper or any other
b) Cost relating to transport, removal or installation of the
liable for indirect or consequential loss or any damage to
not cover, and no re-imbursement will be made for such
SAMSUNG ELECTRONICS (U.K.) LTD.
ventilation or any other cause beyond the control of
purchase contract or otherwise are not affected by this
Naam van klant, Nom du client, il nome del clinte, Onomatepwvnumo tou agopasthv, Sarjanro, Kundens navn, Kundens namn
Naam van handelaar, Nom du marchand, il nome del commerciante, Onoma tou katasthvmatoı, Jalleenmyyjan, Forhandler,
Telefonnummer des Kunden, Telefoon nummer van klant, Numéro de téléphone du client, il numero de telefono del client ,
Handlendesnavn, Forhandler, Nombre de negociante, Nombre del vendedor, Nome de vendedor, Name des Händlers,
Número de telefone de vendedor, Telefonnummer des Handlers, Telefoon nummer van handelaar, Numéro tél´phone du
marchand, il numero di telefono del commeciante, Ariqmovı thlefwvnou tou katasthvmatoı, Myyjän osoite, Forhandlerens
adaptation nor any damage which may result.
Kundeasdress, Kundeadresse, Dirección de client, Direccion del cliente, Endereco de cliente, Adresse des Kunden,
Adres van klant, adresse du client, L’indrizzo del cliente. Dieuvqunsh tou agopasthv, Ostopäivä, Kundens adresse,
Handlendesadress, Forhandleradresse, Dirección de negociante, Dirección del vendedor. Endereco de vendedor,
Adresse des Händlers, Adres van handelaar, Adresse du marchand, Dieuvqunsh tou katasthmatoı, Asiakkaan nimi,
Kundesadress, Kundetelefonnummer, No. de Tel. de client, No. de Tel del cliente, Número de telefone de cliente,
of parts due to normal wear and tear.
Handlendestelesonnummer, Forhandlertelefonnummer, No. de Tel. de negociante, No. de Tel. del vendedor,
Modelnavn, Nombre de modelo, Nombre del modelo, Nome de modelo, Modellbezeichnung, Modelnaam,
purposes or incorrect installation.
Kóbetid, Købsadato, Fecha de compra, Data de compra, Kaufdatum, Datum van aankoop, Date d’achat,
Kundesnavn, Kundenavn, Nombre de cliente, Nombrre del cliente, Nome de cliente, Name des Kunden,
present it to the dealer to quality for guarantee service,
Please ensure the form above is completed at the time of purchase and
Nom du modèle, II nome di modello, Montevlo proi>ovntoı, Asiakkaan puh.nro, Modelnaven, Modell
La data d’acquisto, Hmeromhniva agoravı agorasthv, Asiakkaan osoite, Salgsdato, Inköpsdatumv
related equipment or material.
Serienummer, No. de serie, Número serial, Seriennummer, Serie nummer, Numéro de série,
Ariqmovı thlefwvnou tou agorasthv, Myyjän puh.nro, Kundens telefonnr, Kundens telefonnr.
II numero di matricola, Ariqmovı kataskeuhvı, Malli, Serienummer., Serienr
Samsung.
product.
otherwise your guarantee may be affected.
Forhandlerens adresse, Handlarens adress
tel.nr., Handlarens telefonnr.
the terms issued to purchasers in the country concerned. In case
and, any such repair work and damage to the products caused
CUSTOMER’S TEL. NO.
This Samsung product is warranted for the period of twelve (12)
materials and workmanship. In the event that warranty service is
required, you should return the product to the retailer from whom
However, Samsung Authorised Dealers and Authorised Service
presented with the original invoice or sales slip or confirmation,
will be made for repairs carried out by non Samsung Dealers
CUSTOMER’S NAME
DEALER’S ADDRESS
Centres in other EC Countries will comply with the warranty on
and the serial number on the product has not been defaced.
DEALER’S TEL. NO.
months from the original date of purchase, against defective
DEALER'S STAMP & SIGNATURE
MODEL NAME
Euro Service Centre, Stafford Park 12,
Tel: 0870) 2420303, Fax: 01952) 297617
by such repair work will not be covered by this warranty.
SERIAL NO.
of difficulty, details of our Authorised Service Centres are
TELFORD, Shropshire TF3 3BJ,
GUARANTEE
ELECTRONICS
GARANZIA
GARANTÍA
GARANTIA
GARANTIE
GARANTI
ΕΓΓΥΗΣΗ
I WARRANTY CONDITIONS
TAKUU
it was purchased.
available from:
Customer’s address · Aterforsaljare

ELECTRONICS
www.samsungvcr.com AC68-01880C
(Rev.01)
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.