EN
Topcom logo
Official user manual

Topcom 4056C

72 pages·983 KB·Telephone·PDF·ENDEFRITNLJA
Topcom 4056C
Table of Contents 29 sections BUTLER 4056/4056C · USER GUIDE KULLANICI KILAVUZU · Safety Instructions · Disposal of the device (environment) · … ShowHide
Page 1 of the Topcom 4056C user manual — USER GUIDE KULLANICI KILAVUZU
Page 1 · click to enlarge
Page 1

BUTLER 4056/4056C

Topcom 4056C — BUTLER 4056/4056C diagram (page 1)
Fig. 1
Topcom 4056C — BUTLER 4056/4056C diagram (page 1)
Fig. 2

USER GUIDE KULLANICI KILAVUZU

Page 2 of the Topcom 4056C user manual — BUTLER 4056/4056C
Page 2 · click to enlarge
Page 2

numbers will NOT be shown on the display of your telephone.

Önemli ’Caller ID’ (arayanı gösterme) hizmetinden yararlanabilmek için, telefon hattında bu servisin etkinleútirilmiú olması gerekir. Normalde, bu fonksyonu etkinleútirmek için telefon úirketinden ayrı bir abonelik almanız gerekir. Telefon hattınızda Caller ID fonksyonu yoksa, gelen telefon

numaraları telefonunuzun ekranında GÖSTERøLMEZ.

This product is in compliance with the essential requirements and other relevant provisions of the R&TTE directive 1999/5/EC.

The Declaration of conformity can be found on : http://www.topcom.net/support/cedeclarations.php

To be connected to the public analogue telephone network.

Kamu analog telefon úebekesine ba÷lanmak için.

The CE symbol indicates that the unit complies with the essential

requirements of the R&TTE directive.

CE simgesi, ünitenin R&TTE direktifinin temel úartlarına uygun oldu÷unu gösterir.

The features described in this manual are published with reservation to modifications.

Bu kullanım kılavuzunda açıklanan özellikler, de÷iúiklik hakkı saklı tutularak

yayınlanmaktadır.

Page 3 of the Topcom 4056C user manual — BUTLER 4056/4056C
Page 3 · click to enlarge
Page 3

1 Installation 6 1.1 Base 6 1.2 Charger (only in Twin, triple or quattro pack) 6 1.3 Handset 7 2 Keys/LED 7 3 Display (LCD) 9 4 Handset operation 10 4.1 Setting the language 10 4.2 Making Calls 11 4.3 Receiving a Call 12 4.4 Activate/deactivate handsfree function 12 4.5 Transferring a call to another handset 13 4.6 Out of Range Warning 13 4.7 Setting the speaker volume 13 4.8 Call Duration Indicator on the Display 13 4.9 Turning off the microphone (mute) 14 4.10 Pause key 14 4.11 Conference call (two internal DECT handsets and one external caller) 14 4.12 Locating a misplaced handset (paging) 14 4.13 Using the alphanumeric handset keypad 14 4.14 The Phone Book 15 4.15 Switch the handset on/off 17 4.16 Setting the ring volume level on the handset 17 4.17 Setting the ringer melody on the handset 18 4.18 Setting the ring volume and melody Of the base 18 4.19 Locking the key pad 19 4.20 Turning key click on/off 19 4.21 The R key (flash) 19 4.22 Changing the PIN code 20 4.23 Subscribing a handset to a B24xx, 28xx, 29xx, 32xx, 40xx 20 4.24 Subscribing Butler 4056 handset on another base (other brand/model) 21 4.25 Removing subscription of a handset to a base unit 21 4.26 Selecting a base unit 22 4.27 Barring outgoing calls 23 4.28 Direct Call 23 4.29 Default settings (reset) of the parameters 24 4.30 Complete Reinitialisation of the telephone 24 4.31 Setting the handset dialling mode 25 5 Caller ID/CLIP 25 5.1 Setting the date and time 25 5.2 The Call List 26 5.3 Calling a number from the Call List 26 5.4 Storing a number from the Call List in the Phone Book 26 5.5 Deleting numbers from the Call List 27 6 Voice mail indicator 27

Page 4 of the Topcom 4056C user manual — BUTLER 4056/4056C
Page 4 · click to enlarge
Page 4

7 Base telephone operation 27 7.1 Making a call 27 7.2 Adjusting the speaker volume 27 7.3 Transfer a call from base to handset 27 8 Answering Machine 28 8.1 Setting the internal voice prompt language 28 8.2 LED Display 28 8.3 Base Key Functions 28 8.4 Outgoing Messages 29 8.5 Turning Answering Machine On/Off 30 8.6 Setting Number of Rings 30 8.7 Checking Number of Rings 30 8.8 Setting Day and Time 30 8.9 Checking Day/Time 31 8.10 Programming the VIP Code 31 8.11 Operation 32 8.12 Recording a Memo 32 8.13 Playback of Incoming Messages and Memos 32 8.14 Erasing Messages 32 8.15 Memory Full 33 8.16 Remote Operation 33 8.17 Turning Answering Machine On Remotely 34 9 Trouble shooting 35 10 Topcom warranty 36 10.1 Warranty period 36 10.2 Warranty handling 36 10.3 Warranty exclusions 36 11 Technical characteristics 36

Page 5 of the Topcom 4056C user manual — Cleaning
Page 5 · click to enlarge
Page 5

Safety Instructions

  • Only use the charger plug supplied. Do not use other chargers, as this may damage the battery cells.
  • Only insert rechargeable batteries of the same type. Never use ordinary, nonrechargeable batteries. Insert rechargeable batteries so they connect to the right poles (indicated in the battery compartment of the handset).
  • Do not touch the charger and plug contacts with sharp or metal objects.
  • The operation of some medical devices may be affected.
  • The handset may cause an unpleasant buzzing sound in hearing aids.
  • Do not place the basic unit in a damp room or at a distance of less than 1.5 m away from a water source. Keep water away from the handset.
  • Do not use the telephone in environments where there is a risk of explosions.
  • Dispose of the batteries and maintain the telephone in an environment-friendly manner.
  • As this telephone cannot be used in case of a power cut, you should use a mainsindependent telephone for emergency calls, e.g. a mobile phone.

Disposal of the device (environment)

At the end of the product lifecycle, you should not throw this product into the normal household garbage but bring the product to a collection point for the recycling of electrical and electronic equipments. The symbol on the product, user guide and/or box indicate this.

Some of the product materials can be re-used if you bring them to a recycling point. By re- using some parts or raw materials from used products you make an important contribution to the protection of the environment. Please contact your local authorities in case you need more information on the collection points in your area.

Cleaning

Clean the telephone with a slightly damp cloth or with an anti-static cloth. Never use cleaning agents or abrasive solvents.

Page 6 of the Topcom 4056C user manual — 1 Installation
Page 6 · click to enlarge
Page 6

1 Installation

Before you use the telephone for the first time, you must first make sure the battery is charged for 20 hours. If you do not do this, the telephone will not work optimally.

  • 1.1 Base For installation, do the following:
  • Plug one end of the adaptor into the outlet and the other end into the adapter jack on the bottom of the telephone.
  • Connect one end of the telephone cord with the wall phone jack and the other end to the bottom of the telephone.
Topcom 4056C — 1 Installation diagram (page 6)
Fig. 3 · 1 Installation

adapter outlet wall phone jack

1.2 Charger (only in Twin, Triple or Quattro pack) • Connect the AC adaptor to the electric socket.

adapter jack · telephone connection

Page 7 of the Topcom 4056C user manual — /P
Page 7 · click to enlarge
Page 7
Topcom 4056C — 2 Keys/LED diagram (page 7)
Fig. 4 · 2 Keys/LED
  • 1.3 Handset
  • Open the battery compartment (see below).
  • Insert the batteries respecting the (+ and -) polarity .
  • Close the battery compartment.
  • Leave the handset on the base unit for 20 hours. The Line/Charge indicator (LED) on the base unit will light up.
  • Battery indicator:
  • The battery is fully charged.
  • The battery is half drained (50%)
  • The battery is low. When the battery is low, you will hear warning signals and the battery symbol on the display will blink.

2 Keys/LED

Topcom 4056C — 2 Keys/LED diagram (page 7)
Fig. 5 · 2 Keys/LED

Handset

1. Display 2. Line key 3. Up/Handsfree key / 4. Programming key/INT key 5. Phonebook key 6. Redial/Pause key 7. Microphone 8. Volume/Ringer key / 9. Alphanumeric keys 10. Delete/Mute key/Escape key 11. Down/Flash key / R

/P

Page 8 of the Topcom 4056C user manual — Base
Page 8 · click to enlarge
Page 8

Charger

Topcom 4056C — Charger diagram (page 8)
Fig. 6 · Charger
12. Charge indicator

Base

13. Paging key 14. Line/Charge indicator (LED) 15. Base telephone dialling keys 16. Line/Handsfree base telephone key 17. Flash key R/ Ring volume base 18. Redial key / Ring melody base 19. Voice prompt select switch 20. Numbers of rings setting key 21. VIP code key 22. OFF-hook base telephone LED 23. Memory full LED 24. Messages/answering ON-OFF LED 25. Answering machine key 26. Microphone 27. Speaker
Topcom 4056C — Base diagram (page 8)
Fig. 7 · Base

24 14 13 17 16

Page 9 of the Topcom 4056C user manual — DISPLAY LANGUAGES DISPLAY LANGUAGES VOICE PROMPT 20
Page 9 · click to enlarge
Page 9

DISPLAY LANGUAGES DISPLAY LANGUAGES VOICE PROMPT 20

3 Display (LCD)

13 12 11 10 9 7 6 14 5

1. Number of calls received. 2. Date (day/month) of calls received. 3. Time (hour:minutes) of calls received. 4. Call information. 5. Symbol display ( ): – this symbol means that the handset is located within the range of the base unit. – when this symbol starts blinking, this means you are beyond the range of the base unit. Move closer to the base unit so that the connection between the base unit and the handset can be restored. 6. Symbol display ( ): – this symbol means that the telephone has received calls that are automaticallystored in the Call List.

Page 10 of the Topcom 4056C user manual — 4 Handset operation
Page 10 · click to enlarge
Page 10

7. Symbol display ( ): – this symbol means that the mute function is activated, the microphone is turned off during a conversation. 8. Symbol display ( ): – this symbol appears on the display when you make or receive a call. 9. Symbol display ( ): – this symbol means that the ringer is turned off. When you receive a call, the telephone does not ring. The telephone will ring when you receive an internal call. 10. Symbol display ( ): – this symbol is the battery indicator. 11. Symbol display ( ): – this symbol means you are in the menu. 12. Symbol display ( ): – this symbol appears when you browse the numbers in the Phone Book. 13. Symbol display ( ): – this symbol appears when you have received a voice mail message (see chapter 6). 14. Symbol display ( ): – this symbol means that the handsfree function is activated. You can now talk without having to pick up the handset. – Blinks when base telephone is active. You can’t take the line with the handset as long as base telephone is active!

4 Handset operation

4.1 Setting the language The telephone has 14 display languages: see display languages table on packaging!!

  • To set the language, do the following:
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘SETTING’ appears on the display
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘LANGUAGE’ appears on the display.
  • Press the Programming key .
  • The language set appears on the display.
  • Press the Up or Down key repeatedly to select the language you would like to use.
  • Once the desired language appears on the display, press the Programming key to confirm your selection or repeatedly press the ESC key to leave the menu.
Page 11 of the Topcom 4056C user manual — 4 Handset operation
Page 11 · click to enlarge
Page 11

4.2 Making Calls When making external calls through the handset, base telephone operation is not possible!!!

  • 4.2.1 External Call
  • Press the Line key .
  • The Line/Charge indicator (LED) on the base unit will blink. ‘EXT’ and the Call symbol appear on the display.
  • You will hear the dial tone. Dial the telephone number you wish to call.
  • The number appears on the display and is dialled.
  • After finishing your call, press the Line key to hang up.
  • 4.2.2 Number preparation
  • Dial the telephone number you wish to call. You can correct the number by pressing the Delete/Mute key .
  • Press the Line key .
  • The Line/Charge indicator (LED) on the base unit will blink. ‘EXT’ and the Call symbol appear on the display.
  • The telephone number is dialled automatically.
  • After finishing your call, press the Line key to hang up.
  • 4.2.3 Redialling the last number dialled
  • Press the Line key .
  • The Line/Charge indicator (LED) on the base unit will blink. ‘EXT’ and the Call symbol appear on the display.
  • You will hear the dial tone.
  • Press the Redial key . The number you last called is dialled automatically.
  • 4.2.4 Redial one of the last 5 numbers dialled
  • Press the Redial key . The number you last called appears on the display. If you would like to dial one of the last 5 numbers dialled, press the Redial key a few times until the desired number appears on the display.
  • Press the Line key .
  • The number shown on the display is dialled automatically.
  • After finishing your call, press the Line key to hang up.
  • 4.2.5 Calling a programmed number from the Phone Book The telephone has a Phone Book in which you can program the telephone number with name. If you would like to call a number from the Phone Book:
  • Press the Phone Book key . The first number of the Phone Book appears on the display.
  • Press the Up or Down key repeatedly to select the telephone number you wish to call.
  • Press the Line key .
  • The number shown on the display, is dialled automatically.
  • After finishing your call, press the Line key to hang up.
Page 12 of the Topcom 4056C user manual — 4.3 Receiving a Call
Page 12 · click to enlarge
Page 12
  • 4.2.6 An internal call: calling another handset This function only works if multiple handsets are subscribed to the base unit !
  • Press the INT key twice.
  • ‘INT‘ appears on the display
  • Dial the number of the handset you would like to call.
  • After finishing your call, press the Line key to hang up.

4.3 Receiving a Call

  • 4.3.1 Receiving an external call
  • All subscribed handsets will ring when you receive a call.
  • The Call symbol blinks on the display.
  • The telephone number of the caller appears on the display if you have Caller ID service (CLIP). Consult your telephone company. The name of the caller also appears on the display if:
  • – the name is programmed into the Phone Book – the network sends the name together with the telephone number (FSK CID system only).
  • Press the Line key to accept the external call.
  • During the call ‘EXT’ and the symbol appear on the display. The call timer starts running.
  • After finishing your call, press the Line key to hang up or put the handset back on the base unit.
  • 4.3.2 Receiving an internal call This function only works if multiple handsets are subscribed to the base unit!
  • The handset rings.
  • ‘INT’ and the number of the handset calling, appear on the display. The Call symbol blinks on the display.
  • Press the Line key to accept the internal call.
  • During the call, ‘INT’, the handset number of the caller and the symbol appear on the display. The call timer starts running.
  • After finishing your call, press the Line key to hang up.
  • 4.3.3 Receiving an external call during an internal call If you receive an external call during an internal call, you will hear a call waiting tone (double beep) on both handsets being used for an internal call.
  • Press the Line key twice to accept the external call.
  • After finishing your call, press the Line key to hang up.

4.4 Activate/deactivate handsfree function This function allows you to communicate without having to pick up the handset. When you are talking, press the Up/Handsfree key / to activate the handsfree function. Press the same button to deactivate the handsfree function.

Page 13 of the Topcom 4056C user manual — 4.3 Receiving a Call
Page 13 · click to enlarge
Page 13
  • 4.5 Transferring a call to another handset
  • You have an external caller on the line.
  • Press the INT key twice.
  • The external call is now on hold.
  • ‘INT‘ appears on the display.
  • Dial the number of the handset to which you would like to transfer the call.
  • If the handset dialled is answered, you can have an internal conversation. Press the Line key and the external call is transferred.
  • If the handset dialled is not answered, press the Down key to speak to the external caller again.
  • 4.6 Out of Range Warning If the handset is out of range of the base unit, a warning signal will sound.
  • ‘SEARCHING’ appears on the display and the symbol blinks on the display.
  • Move closer to the base unit.
  • As soon as you are back within range of the base unit, a signal sounds and the symbol

stops blinking.

  • 4.7 Setting the speaker volume Use the Volume/Ringer key / to set the volume of the speaker (handset). You can select from 5 levels. The telephone is set to level ‘3’ by default. During a call, you can change the volume:
  • Press the Volume/Ringer key / .
  • The volume level currently set appears on the display.
  • Use the number keys to set the desired level (1-5).
  • Press the Volume/Ringer key / to confirm your selection.

4.8 Call Duration Indicator on the Display As soon as you press the Line key the call duration appears on the display (minutes- seconds). E.g. “ 01-20 “ for 1 minute and 20 seconds. The call duration remains visible on the display for 5 seconds after each call.

Page 14 of the Topcom 4056C user manual — 4.3 Receiving a Call
Page 14 · click to enlarge
Page 14
  • 4.9 Turning off the microphone (mute) It is possible to turn off the microphone during a call by pressing the Delete/Mute key . Now you can speak freely without the caller being able to hear you.
  • You are on the phone. The Line/Charge indicator (LED) on the base unit will blink and the Call symbol appears on the display.
  • Press the Delete/Mute key to turn off the microphone.
  • The symbol ‘X’ appears on the display ( ).
  • When you want to resume the conversation, press the Delete/Mute key again.
  • The symbol ‘X’ disappears from the display ( ). The person on the other end of the line can hear you again.

4.10 Pause key If you dial a telephone number and you would like to add a pause to this number, press the Pause key at the desired place in the number. When you call this number, this pause (3 seconds) is automatically included.

  • 4.11 Conference call (two internal DECT handsets and one external caller) You can have a telephone conversation with one internal and one external caller at the same time.
  • While on the line with an external caller, press the INT key twice.
  • The external call is now on hold.
  • ‘INT‘ appears on the display.
  • Dial the number of the handset you would like to include in the call.
  • Once the handset dialled is answered, keep the ‘#’ key pressed for 3 seconds.
  • ‘CONFERENCE’ appears on the display.
  • Now you are connected to one external and one internal caller (conference call).

4.12 Locating a misplaced handset (paging) If you cannot find the handset, briefly press the Paging key on the base unit. All handsets subscribed with the base unit will sound a signal so you can locate the misplaced handset. To stop the signal, briefly press the Line key on any handset.

4.13 Using the alphanumeric handset keypad Use the alphanumeric keypad to type text. To select a letter, press the corresponding key. E.g. if you press the alphanumeric key ’5’, the first character (j) appears on the display. Press it repeatedly to select other characters from this key.

Press the ‘2’ key twice to select the letter ‘B’. If you would like to select both ‘A’ and ‘B’ after each other, first press the ‘2’ key once to select ‘A’, wait 2 seconds until the cursor moves to the next position and then press the ‘2’ key twice to select ‘B’. You can delete characters mistakenly typed by using the Delete key . The character in front of the cursor will be deleted. You can move the cursor by pressing the Up and Down keys .

Page 15 of the Topcom 4056C user manual — 4.3 Receiving a Call
Page 15 · click to enlarge
Page 15

Available characters Press the right keys to get the following characters:

1. / 1

2 A B C a b c 2

3 D E F d e f 3

4 G H I g h i 4

5 J K L j k l 5

6 M N O m n o 6

7 P Q R s p q r s 7

8 T U V t u v 8

9 W X Y Z w x y z 9

4.14 The Phone Book The phonebook allows you to memorise 50 telephone numbers and names. You can enter names of up to 9 characters length and numbers of up to 25 digits length.

  • 4.14.1 Adding a number and a name to the Phone Book
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘PHONE BOOK’ appears on the display.
  • Press the Programming key .
  • ‘SEARCH‘ appears on the display.
  • Press the Up or Down key repeatedly until ‘ADD NEW’ appears on the display.
  • Press the Programming key .
  • ‘NAME‘ appears on the display.
  • Enter the name. Use the alphanumeric keys.
  • Press the Programming key .
  • Enter the telephone number. Use the alphanumeric keys.
  • Press the Programming key .
  • You will hear a long beep. The name and the number are stored in the Phone Book.
Show 10 more labels / short text on this page
Keys 1st press · 2nd press · 3rd press · 4th press · 5th press · 6th press · 7th press · 8th press · 9th press · 0 space 0
Page 16 of the Topcom 4056C user manual — 4.3 Receiving a Call
Page 16 · click to enlarge
Page 16
  • 4.14.2 Looking up a number in the Phone Book
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘PHONE BOOK’ appears on the display.
  • Press the Programming key .
  • ‘SEARCH‘ appears on the display.
  • Press the Programming key .
  • Enter the first letters of the desired name.
  • Press the Programming key .
  • The first name, corresponding with these letters appears on the display.
  • Press the Up or Down key to browse for other numbers in the Phone Book.
  • Once the desired number appears on the display, the number will be automatically dialled once the Line key is pressed.
  • 4.14.3 Changing a name or number in the Phone Book
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘PHONE BOOK’ appears on the display.
  • Press the Programming key .
  • ‘SEARCH‘ appears on the display.
  • Press the Up or Down key repeatedly until ‘EDIT’ appears on the display.
  • Press the Programming key .
  • The first number in the Phone Book appears on the display.
  • Press the Up or Down key until the desired number appears on the display.
  • Press the Programming key to change the selected number programmed into the memory.
  • Press the Delete key to delete each letter of the name and use the alphanumeric keypad to enter the correct name.
  • Press the Programming key .
  • Press the Delete key to delete each digit of the number and use the alphanumeric keypad to enter the correct number.
  • Press the Programming key to save the changes made.
  • 4.14.4 Deleting name and number from the Phone Book
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘PHONE BOOK’ appears on the display.
  • Press the Programming key .
  • ‘SEARCH‘ appears on the display.
  • Press the Up or Down key repeatedly until ‘DELETE’ appears on the display.
  • Press the Programming key .
  • The first number in the Phone Book appears on the display.
  • Press the Up or Down key until the number you want to delete appears on the display.
  • Press the Delete key .
  • ‘DELETE ?’ appears on the display.
  • Press the Programming key to confirm that you want to delete it.
Page 17 of the Topcom 4056C user manual — 4.15 Switch the handset on/off
Page 17 · click to enlarge
Page 17

4.15 Switch the handset on/off

  • 4.15.1 Switch the handset off The handset is turned on.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘POWER OFF?’ appears on the display.
  • Press the Programming key . The telephone turns itself off. You cannot dial any more numbers, nor receive any calls. Note : If you would like to leave the menu without turning off the handset, press the Delete/Mute key .

4.15.2 Switch the handset on The handset is turned off. • Press the Programming key . The telephone turns itself on.

4.16 Setting the ring volume level on the handset You can change the ring volume of an incoming call. You have 10 levels. You can set the ring volume of internal and external calls separately so you can hear a difference. If you select level ‘0’, the symbol appears on the display and you no longer hear the phone ring when an external call is received (you still hear it ring for internal calls). Level ‘9’ is the highest level. The telephone is set to level ‘5’ by default.

  • 4.16.1 Setting the ring volume for external calls (0-9)
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘RING SEL’ appears on the display.
  • Press the Programming key .
  • ‘EXTERNAL‘ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘VOLUME’ appears on the display.
  • Press the Programming key .
  • The current volume level used appears on the display.
  • Enter a number between 0 and 9 to select the desired ringer volume. Use the number keypad to do this.
  • Press the Programming key to confirm your selection.
  • 4.16.2 Setting the ringer volume for internal calls (1-9)
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘RING SEL’ appears on the display.
  • Press the Programming key .
  • ‘EXTERNAL‘ appears on the display.
  • Press the Up or Down key repeatedly until ‘INTERNAL’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘VOLUME’ appears on the display.
  • Press the Programming key .
  • The current volume level appears on the display.
Page 18 of the Topcom 4056C user manual — 4.18 Setting the ring volume and melody Of the base
Page 18 · click to enlarge
Page 18
  • Enter a number between 1 and 9 to select the desired ringer volume. Use the number keypad to do this.
  • Press the Programming key to confirm your selection.

4.17 Setting the ringer melody on the handset You can change the ringer melody for an incoming call. You have 9 ringer melodies to choose from (1-9). By default, the ringer melody is set to ‘5’.

  • 4.17.1 Setting a ringer melody for external calls (1-9)
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘RING SEL’ appears on the display.
  • Press the Programming key .
  • ‘EXTERNAL‘ appears on the display.
  • Press the Programming key .
  • ‘MELODIES‘ appears on the display.
  • Press the Programming key .
  • The currently set ringer melody appears on the display.
  • Enter a number between 1 and 9 to select he desired ringer melody. Use the number keypad to do this.
  • Press the Programming key to confirm your selection.
  • 4.17.2 Setting a ringer melody for internal calls (1-9)
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘RING SEL’ appears on the display.
  • Press the Programming key .
  • ‘EXTERNAL‘ appears on the display.
  • Press the Up or Down key repeatedly until ‘INTERNAL’ appears on the display.
  • Press the Programming key .
  • ‘MELODIES‘ appears on the display.
  • Press the Programming key .
  • The currently set ringer melody appears on the display.
  • Enter a number between 1 and 9 to select the desired ringer melody. Use the number keypad for this.
  • Press the Programming key to confirm your selection.

4.18 Setting the ring volume and melody Of the base

  • 4.18.1 Setting the base melody
  • Press the redial key at the base
  • The current ring melody will be played
  • Press 1-5 on the base for the desired ring melody
  • 4.18.2 Setting the base ring volume
  • Press the Flash R key at the base
  • The current volume will be heard
  • Press 1-5 to select the desired volume, or ‘0’ to turn the base ringer off.
Page 19 of the Topcom 4056C user manual — 4.18 Setting the ring volume and melody Of the base
Page 19 · click to enlarge
Page 19
  • 4.19 Locking the key pad If you lock the alphanumeric keypad, it is impossible to dial a telephone number. Only the Programming key can still be used. ‘KEY LOCKED’ will be displayed on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘KEY SETUP’ appears on the display.
  • Press the Programming key .
  • KEY LOCK‘ appears on the display.
  • Press the Programming key .
  • The current status of the keypad appears on the display:
  • – ‘LOCK’: the keypad is locked – ‘UNLOCK’: the keypad is not locked
  • Press the Up or Down key to make your selection.
  • Press the Programming key to confirm your selection.
  • 4.20 Turning key click on/off You can set the telephone to make a sound whenever you press a key.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘KEY SETUP’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘KEY CLICK’ appears on the display.
  • Press the Programming key .
  • The current status appears on the display:
  • – ‘CLICK ON’: turn on key click – ‘CLICK OFF’: turn off key click
  • Press the Up or Down key to make your selection.
  • Press the Programming key to confirm your selection.
  • 4.21 The R key (flash) Press the Flash key ‘R’ to use certain services such as “call waiting” (if your telephone company offers this feature); or to transfer calls if you use a telephone exchange (PABX). The Flash key ‘R’ is a brief interruption of the line. You can set the flash time to 100ms or 300ms. This is set to 100ms by default! However, if your system requires a longer flash time, do the following:
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘SETTING’ appears on the display
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘RECALL’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly to select the flash time: – SHORT = 100ms – LONG = 300ms
  • Press the Programming key to confirm your selection.
Page 20 of the Topcom 4056C user manual — 4.18 Setting the ring volume and melody Of the base
Page 20 · click to enlarge
Page 20
  • 4.22 Changing the PIN code Certain functions are only available if you know the PIN code of the telephone. The PIN code has 4 digits. The default PIN code setting is ‘0000’. If you would like to change the default PIN code and set your own secret code, do the following:
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘SETTING’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘PIN CODE’ appears on the display.
  • Press the Programming key .
  • ‘OLD CODE’ appears on the display.
  • Enter the old PIN code. Use the number keys.
  • Press the Programming key .
  • ‘NEW CODE’ appears on the display.
  • Enter the new PIN code in. Use the number keys.
  • Press the Programming key .
  • ‘AGAIN’ appears on the display.
  • Enter the new PIN code again. Use the number keys.
  • Press the Programming key .
  • You hear a confirmation tone. The new PIN code has been set.
  • 4.23 Subscribing a handset to a B24xx, 28xx, 29xx, 32xx, 40xx In order to be able to make and receive telephone calls, a new handset has to be subscribed to the base unit. You can subscribe 5 handsets to one base unit. By default, each handset is subscribed as handset 1 on the base unit upon delivery (base unit 1). !!! You only need to subscribe the handset if:
  • the handset subscription has been removed from the base unit (e.g. for reinitialisation)
  • you want to subscribe a different handset to this base unit. The underlined procedure is only applicable to a B40XX handset and base unit!! Keep the Paging key on the base unit pressed for 10 seconds until The Line/Charge indicator on the base unit begins to blink rapidly. The Line/Charge indicator will blink rapidly for one minute. During this minute, the base unit is in subscribing mode and you must do the following to subscribe the handset:
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘BASE SUB’ appears on the display.
  • Press the Programming key .
  • ‘BASE _‘ appears on the display.
  • Enter a number of the base unit you would like to subscribe the handset to (1-4).
  • Use the number keypad. Note: Each handset can be subscribed to 4 different DECT base units. Each base unit is assigned a number from 1 to 4 in the handset. When you subscribe a new handset, you can assign a base unit number. It is best to use ‘1’ .
Page 21 of the Topcom 4056C user manual — 4.18 Setting the ring volume and melody Of the base
Page 21 · click to enlarge
Page 21
  • ‘SEARCHING’ and the symbol appears on the display.
  • The RFPI code (each base unit has a unique RFPI code) appears on the display and a signal sounds when the handset has found the base unit.
  • Press the Programming key .
  • ‘PIN’ appears on the display.
  • Enter the 4-digit PIN code of the base unit in (default PIN code is ‘0000’). Use the number keypad.
  • Press the Programming key .
  • The handset is subscribed to the base unit.
  • 4.24 Subscribing Butler 4056 handset on another base (other brand/model) Put the base in subscription mode (see manual of the base). If the base is in subscribing mode, you have to do the following to subscribe the handset:
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘BASE SUB’ appears on the display.
  • Press the Programming key .
  • ‘BASE _‘ appears on the display.
  • Enter a number for the base unit to which you would like to subscribe the handset (1-4).
  • Use the number keypad.
  • ‘SEARCHING’ and the symbol appear on the display.
  • The RFPI code (each base unit has a unique RFPI code) appears on the display and a signal sounds once the base unit is found by the handset.
  • Press the Programming key .
  • ‘PIN’ appears on the display.
  • Enter the 4-digit PIN code of the base unit (default PIN code is ‘0000’). Use the number keypad.
  • Press the Programming key .
  • The handset is subscribed to the base unit.

4.25 Removing subscription of a handset to a base unit It is possible to cancel subscription of a handset to a base unit. You would do this if a handset is damaged and has to be replaced by a new one.

  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘SETTING’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘REMOVE HS’ appears on the display.
  • Press the Programming key .
  • ‘PIN’ appears on the display.
  • Enter your 4-digit PIN code in (default PIN code is ‘0000’). Use the number keypad.
  • Press the Programming key .
Page 22 of the Topcom 4056C user manual — 4.18 Setting the ring volume and melody Of the base
Page 22 · click to enlarge
Page 22
  • ‘REMOVE HS’ appears on the display.
  • Dial the number of the handset you want to remove (1 –5). Use the number keypad.
  • Press the Programming key .
  • ‘REMOVE HS’ appears on the display and the handset is removed
  • NOT SUB’ appears on the handset removed.

4.26 Selecting a base unit If your handset is subscribed to several base unit stations (max. 4) , you must select a base unit because the handset can only communicate with one base unit at a time. There are two possibilities:

  • 4.26.1 Automatic selection If you set the handset to ‘automatic selection’, the handset will automatically choose the closest base unit in standby.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘SETTING’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘BASE SEL’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘AUTO’ appears on the display.
  • Press the Programming key .
  • ‘SEARCHING’ and the symbol appear on the display.
  • A signal sounds once the handset has found a base unit.
  • 4.26.2 Manual selection If you set the handset to ‘manual selection’, the handset will only choose the base unit you have set.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘SETTING’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘BASE SEL’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘MANUAL’ appears on the display.
  • Press the Programming key .
  • ‘BASE -‘ appears on the display.
  • Enter the number of the base unit you want to select (1-4). Use the number keypad.
  • Press the Programming key .
  • ‘SEARCHING’ and the symbol appear on the display.
  • A signal sounds once the selected base unit has been found.
  • Notes:
  • Before you can select a base unit, the base unit must be subscribed to the handset first.
  • If ‘NOT SUB’ appears on the display, this means the selected base unit does not exist or the handset has not been subscribed.
Page 23 of the Topcom 4056C user manual — 4.18 Setting the ring volume and melody Of the base
Page 23 · click to enlarge
Page 23
  • 4.27 Barring outgoing calls You can program the handsets to bar calls to certain telephone numbers so that for instance ‘00’ international numbers cannot be called. Up to 5 numbers (of max. 5 digits) can be barred. To do this, do the following:
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘SETTING’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘BARRING’ appears on the display.
  • Press the Programming key .
  • ‘PIN’ appears on the display.
  • Enter your PIN code
  • Press the Programming key .
  • ‘BAR NUM ’ appears on the display. You are in memory “1. _ _ _ _ _”.
  • Press the Up or Down key to select one of the 5 memories.
  • Enter the number (max. 5 digits) to be barred, e.g. 01486.
  • Press the Programming key .
  • ‘HS _ _ _ _ _’ (= number on the handset (1-5)) ‘01486’ (= the barred numbers) appear on the display.
  • Enter the numbers of the handsets from which the barred numbers cannot be called.
  • e.g. Press the number key 2, 3 and 5. On the display, this will appear: HS _2 3_5 01486 These handsets can no longer dial numbers beginning with ‘01486’.
  • Press the Programming key to confirm your selection. Repeat the same procedure described above if you would like to bar other numbers (max. 5)!

4.28 Direct Call By setting a Direct Call number, the phone will automatically take the line and dial out this number. This function is useful to use the phone as a emergency phone.

  • 4.28.1 To program the Direct Call number
  • Press the Programming key
  • Press the Up or Down key until ‘DIRECT’ appears on the display
  • Press the Programming key
  • If necessary, delete the existing number by pressing the Delete-key a few times
  • Enter the direct number
  • Press the Programming key
  • 4.28.2 Turn the Direct Call function ON/OFF To turn it ON:
  • Press the Programming key
  • Press the Up or Down key until ‘DIRECT’ appears on the display
  • Press the mute-key for 2s
  • ‘DIRECT ON’ appears on the display
To turn if OFF• Quick press the Programming key twice
Page 24 of the Topcom 4056C user manual — 4.18 Setting the ring volume and melody Of the base
Page 24 · click to enlarge
Page 24

4.29 Default settings (reset) of the parameters You can reset the standard (default) settings in the telephone. You need the PIN code to do this.

The default settings are: Keypad: not locked Key clicks: active Speaker volume: level Ringer melody: 1 Ringer volume : 5 Selection base unit: automatic Flash time: 100ms

  • To restore the default settings, do the following:
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘SETTING’ appears on the display.
  • Press the Programming key .
  • Press the Up or Down key repeatedly until ‘RESET’ appears on the display.
  • Press the Programming key .
  • ‘PIN’ appears on the display.
  • Enter your PIN code.
  • Press the Programming key .

4.30 Complete Reinitialisation of the telephone This function allows you to completely reinitialise the telephone without requiring your PIN code. This will delete all Phone Book memory entries, all handsets will be removed, all default settings will be restored and the default PIN code will be restored to ‘0000’.

  • Do the following:
  • Disconnect the battery in the telephone.
  • Keep the ‘*’ key pressed and reconnect the battery until the handset rings continually and the display lights up. Release the ‘*’ button and press the Programming key .
  • The handset finds the base unit and a signal sounds.
  • Briefly press the ‘*’ key.
  • ‘RESET ?‘ appears on the display.
  • Press the Programming key to confirm your selection of disconnect the battery to discontinue the procedure.
  • ‘RESETTING‘ appears on the display and a long beep tone sounds.
  • ‘NOT SUB‘ appears on the display. The handset is completely reinitialised.

Afterwards, you must resubscribe all handsets as described in point 4.23! However you no longer need to set the base unit to subscription mode, because this now happens automatically!

Page 25 of the Topcom 4056C user manual — 5 Caller ID/CLIP
Page 25 · click to enlarge
Page 25
  • 4.31 Setting the handset dialling mode There are two types of dialling modes:
  • DTMF/Tone dialling (the most common)
  • Pulse dialling (for older installations)
  • To change the mode of numeration:
  • Press the Programming key
  • Press the Up or Down key repeatedly until ‘SETTING’ appears on the display.
  • Press the Programming key
  • Press the Up or Down key repeatedly until ‘DIAL MODE’ appears on the display.
  • Press the Programming key
  • Select ‘TONE’ or ‘PULSE’ by means of the UP and Down key
  • Press the Programming key to confirm

5 Caller ID/CLIP

  • (This service only works when you have a Caller ID/Clip subscription. Contact your telephone company). When you receive a call, the telephone number of the caller, the date and time appears on the handset display. The telephone can receive calls in both FSK and DTMF. If the name is programmed in the Phone Book, the name in the Phone Book is displayed! The telephone can store 30 calls in a Call List that can be reviewed later. The telephone never stores the same call twice. When the memory is full, the new calls automatically replace the oldest calls in the memory. The symbol on the display blinks if the call is not read or not answered. If the Call List is empty and you press the Up key , three beep tones will sound. You can view the information of an incoming call as follows:
  • Press the Up key . The name (if sent by the network or present in the Phone Book memory) of the caller, the sequence number of the call in the Call List, the date and time of the call appear on the display.
  • Press the Down key . The telephone number of the caller appears on the display.
  • 5.1 Setting the date and time When you receive an incoming call and the date and time are not sent together with the telephone number, this means that the date and the time will not be shown on the display. By setting the date and time, they will be shown on the display, together with the telephone number, every time a call comes in !
  • Press the Programming key .
  • Press the Up or Down key a few times until ‘SETTING’ appears on the display.
  • Press the Programming key .
  • ’DATE/TIME’ appears on the display.
  • Press the Programming key again.
  • When ‘YEAR’ appears on the display, enter the 2 last numbers of the year (00=2000, 01=2001, ...) and press the Programming key to confirm.
Page 26 of the Topcom 4056C user manual — 5 Caller ID/CLIP
Page 26 · click to enlarge
Page 26
  • When ‘MONTH’ appears on the display, enter the month (01=January, 02=February, ...) and press the Programming key to confirm.
  • When ‘DAY’ appears on the display, enter the day of the month and press the Programming key to confirm.
  • When ‘HOUR’ appears on the display, enter the current hour (in 24h format) and press the Programming key to confirm.
  • When ‘MINUTES’ appears on the display, enter the minutes and press the Programming key to confirm. The date and time are now set !
  • 5.2 The Call List The calls received are stored in the Call List (max. 30 numbers).
  • Briefly press the Up key to view the most recent call.
  • The name of the most recent caller appears on the display. If no name is available, ‘NO NAME’ appears on the display.
  • If it is a private number, ‘UNAVAL’ appears on the display.
  • The date and time the call was received are linked to each call.
  • Briefly press the Down key to view the telephone number of the call.
  • Briefly press the Down key to browse other numbers on the list. Notes:
  • If neither the Up or Down key is pressed for 15 seconds, the telephone will return to standby mode.
  • After a call is received, the number of the caller remains on the display for 15 seconds after the last ring.
  • Caller ID is not available while you are on the line.
  • 5.3 Calling a number from the Call List
  • Press the Up key to go to the Call List
  • Press the Up key to look up the desired call. Press the Down key to view the telephone number.
  • Once the number is on the display, press the Line key and the number is dialled automatically. (The symbols and ‘EXT’ appear on the display and the call timer starts.)
  • 5.4 Storing a number from the Call List in the Phone Book
  • Press the Up key to go to the Call List.
  • Press the Up key to look up the desired number.
  • Press the Phone Book key twice.
  • ‘STORE’ appears on the display.
  • The number is stored in the Phone Book. If the call was displayed without a name (NO NAME), you can add a name to this number in the Phone Book afterwards
  • The telephone returns to standby-modus.
Page 27 of the Topcom 4056C user manual — 7 Base telephone operation
Page 27 · click to enlarge
Page 27

5.5 Deleting numbers from the Call List

  • 5.5.1 Deleting one number
  • Press the Up key to go to the Call List.
  • Press the Up key to find the call you would like to delete.
  • Once this call appears on the display, press the Delete key .
  • ‘DELETE?’ appears on the display.
  • Press the Programming key to confirm your selection or the Delete key to cancel.
  • The call is deleted and the next call appears on the display.
  • 5.5.2 Delete all numbers
  • Press the Up key to go to the Call List.
  • Keep the Delete key pressed until ‘DELETE ALL’ appears on the display.
  • Press the Programming key to confirm your selection or the Delete key to cancel.
  • All calls are deleted.

6 Voice mail indicator

This function only works if you have the voice mail or phone mail service and if the network sends this indication along with the caller ID (CLIP) information! When you receive a new message in your voice mail system, the icon will appear on the display. Once you have listened to your messages, the icon will disappear.

7 Base telephone operation

You can also make a telephone call by using the base station handsfree speakerphone.

  • 7.1 Making a call
  • Press the Handsfree base dialling key to take the line
  • Press the numeric keys on the base to form a telephone number
  • Press again the Handsfree base dialling key to end the telephone conversation

7.2 Adjusting the speaker volume Press the ‘+’ or ‘-’ key during base handsfree conversation to adjust the speaker volume. If the speaker volume is too loud there is the possibility that the speaker starts to oscillate (flute tone). To avoid this, please lower the speaker volume.

  • 7.3 Transfer a call from base to handset During base handsfree conversation you can transfer the call to any registered handset by pressing the paging key . The line indicator LED will start to blink.
  • You can take over the line by any registered handset when pressing the line-key .
  • Or press the paging key again if you don’t want to transfer the call
Page 28 of the Topcom 4056C user manual — 8 Answering Machine
Page 28 · click to enlarge
Page 28

8 Answering Machine

  • The Butler 4056 has a built-in digital answering machine with a recording capacity of 9 min. The answering machine can be operated remotely and features the possibility of recording two outgoing messages (OGM 1 and OGM 2) (maximum of 2 min). There are 2 possibilities:
  • With OGM 1, the caller has the possibility to leave a message
  • With OGM 2, only the outgoing message is given without the caller having the opportunity to leave a message The max. recording time for each incoming message = 3 min.

An internal voice will state various information, such as day and time of the call, as well as settings such as VIP code, ringer tones. The languages of the internal voice is stated on the packaging!

8.1 Setting the internal voice prompt language There are 3 voice prompt languages which can be selected by the switch at the bottom of the base. Please set the switch at the desired language and press the play key to confirm the language setting.

8.2 LED Display The new message LED / will flash if new messages have been received; the number of flashes between each long pause indicates how many new calls have been recorded. If the answering machine is switched off, the On-Off LED / does not light. MEMORY FULL-LED is turned on when the internal memory is full and no new messages can be recorded.

8.3 Base Key Functions NoteThe & keys are at the bottom of the base

Key Stand-by mode During message

play-back Press key briefly press key for 2 seconds

1 Play OGM Record OGM Go to previous

2 Playback messages None Pause

3 None Record memo Skip message

4 Set volume speech +ringing

5 / Select OGM Switch On-Off Stop

1,2 · message · None Set volume

Page 29 of the Topcom 4056C user manual — 8 Answering Machine
Page 29 · click to enlarge
Page 29

6 Play VIP-code Set VIP-code None

7 Current number of

8 Playback Time Set date/time None

9 None Delete all messages Delete message or

  • 8.4 Outgoing Messages Two outgoing messages of 2 minutes can be recorded (OGM1 and OGM2).
  • Outgoing message 1 for the answering function and possibility for callers to leave a message.
  • Outgoing message 2 for the answering function without allowing callers to leave a messages on the machine.
  • 8.4.1 Recording outgoing messages (OGM 1 or OGM 2)
  • Press the / -key to select the OGM.
  • A voice will playback the recorded OGM
  • Press the -key for two seconds
  • Record the outgoing message after the beep
  • Press the Stop -key to stop recording. Note: The recording cannot exceed 2 minutes. If no outgoing message is recorded, the prerecorded outgoing message is used.

8.4.2 Playback the Outgoing Message To check the outgoing message now set: • Press the -key. Note: To stop playing the welcome note briefly press the Stop -key .

  • 8.4.3 Select outgoing message
  • Press the / -key to switch between the 2 outgoing messages.
  • The internal voice will confirm the set outgoing message.
  • Notes:
  • It is only possible to select an outgoing message if the answering machine is turned on.
  • If the memory is full, only outgoing message 2 can be selected (only answering without recording messages)
Show 7 more labels / short text on this page
Set numbers of · None · ring tones · ring tones · delete OGM · 1,2 · 1,2
Page 30 of the Topcom 4056C user manual — 8 Answering Machine
Page 30 · click to enlarge
Page 30
  • 8.4.4 Erasing the Outgoing Message If you erase the outgoing message, the default message will be played ‘Please call later’. Erase the outgoing message as follows:
  • Select the desired outgoing message by pressing the / -key.
  • Press the key to play the outgoing message.
  • Keep the key pressed down when the OGM is played back.
  • 8.5 Turning Answering Machine On/Off If the answering machine is on, the -LED will light up and the machine will automatically pick up the line after a number of rings (see 'Setting Number of Rings').
  • Press the key for 2 secs to switch on the answering machine. A voice confirms the setting and says which outgoing message is active (OGM 1 or OGM 2).
  • Press the key for another 2 secs to switch off the answering machine. A voice confirms the setting. Note: Even if the answering machine is off, the machine will automatically pick up after 10 rings in order to enable remote activation (see 8.16 Remote operation)
  • 8.6 Setting Number of Rings The number of rings after which the answering machine will answer calls can be set from 2 – 9 and TS (Toll saver). The standard setting is 3 rings. In Toll saver mode, the machine will answer after 5 rings if there are no new messages, and after 2 rings if there are new messages. If there are no new messages and you call your machine to check your messages remotely (see 8.16 Remote operation), you can hang up after the 2nd ring. You do not need to pay connection fees and you know that you do not have any new messages.
  • Briefly press the key. A voice will state the current number of rings.
  • Press the key for 2 secs to set the number of ringing tones.
  • Press the or key to change the current number of rings.
  • Confirm the setting by pressing the key. The current ring setting is confirmed by the internal voice.
  • Notes:
  • If you do not press any keys for 3 seconds, the machine will revert back to the answering machine menu, without changing the settings.
  • If there is a loss of power in the base, the number of rings will revert to 3.
  • 8.7 Checking Number of Rings
  • Press the key briefly.
  • The internal voice will state the number of rings set.

8.8 Setting Day and Time The day and time setting of the answering machine is independent of the telephone component. The day and time of each call is registered and announced during play-back. The format of the hour depends on the language of the internal voice. e.g. English is in 12- hour format and German is in 24-hour format.

1,2

Page 31 of the Topcom 4056C user manual — 8 Answering Machine
Page 31 · click to enlarge
Page 31
  • Programming the day and time:
  • Keep the -key pressed down for 2 secs.
  • The internal voice will ask you to set the day.
  • Press a few times on or keys to set the day. The internal voice states the current settings.
  • Press the key to confirm the day.
  • The internal voice will ask you to set the hour.
  • Press a few times on or keys to set the hour.
  • Press the key to confirm the hour.
  • The internal voice will ask you to set the minutes.
  • Press a few times on or keys to set the minutes.
  • Press the key to confirm the minutes. The complete day and time setting is then repeated for confirmation.
  • Notes:
  • If you do not press any keys for 8 seconds, the previous day/time setting is saved and the machine automatically exits the day/time setting mode.
  • When you use the machine for the first time and have not yet set the day/time, no day/time registration of incoming messages is recorded.
  • If there is a loss of power to the base, the day/time must be re-entered.

8.9 Checking Day/Time • Press the key to announce the day/time. The internal voice will say the current day/ time setting.

8.10 Programming the VIP Code The VIP code is a 3-digit code used to operate the machine remotely (see Remote Operation). The VIP code is set to '321' by default. Note: If there is a loss of power to the base, the VIP code will revert to '321'.

  • 8.10.1 Changing the VIP Code
  • Keep the - key pressed down for 2 secs to change the VIP code.
  • The internal voice asks you to set the VIP code and says the first number.
  • Press a few times on or keys to set the first number of the VIP code.
  • Press the key to confirm the first number. The internal voice says the current set 2nd digit of the VIP code.
  • Press a few times on or keys to set the second digit of the VIP code.
  • Press the key to confirm the second number. The internal voice says the current set 3rd digit of the VIP code.
  • Press a few times on or keys to set the third digit of the VIP code.
  • Press the key to confirm the VIP code. You will hear a long beep. The internal voice says the new VIP code for confirmation. Note: If you do not press any keys for 8 seconds, the previous VIP code is saved and the machine automatically exits the VIP setting mode.
Page 32 of the Topcom 4056C user manual — 8.14 Erasing Messages
Page 32 · click to enlarge
Page 32

8.10.2 Checking the VIP Code • Press the key to play the VIP code. The internal voice says the current VIP code.

  • 8.11 Operation If a call is received and the answering machine is turned on, the answering machine will automatically pick up the line after the set number of rings. If
  • Outgoing message 1 has been selected, it will be played. After the outgoing message, a beep will be heard and the caller can leave a message (of a max. 3 minutes).
  • Outgoing message 2 has been selected, it will be played. After the beep, the line will automatically be disconnected. The caller does not have the possibility to leave a message. Note: If, during pick-up, nothing is said for 8 seconds, the line will be automatically disconnected.
  • 8.12 Recording a Memo With the Butler 4056, you can record memos. These memos are considered an incoming message that can be picked up later by the user. The max. recording time for a memo is 2 minutes.
  • Press the key for 2 seconds. After the beep, say your memo.
  • Press the Stop -key to stop recording.
  • 8.13 Playback of Incoming Messages and Memos
  • Press the key to play the messages and memos.
  • An internal message tells you how many messages there are (total) and how many new (unheard) messages.
  • The messages are played one at a time. If there are new messages, only the new messages (those that have not been heard) are played.
  • For each message, the internal voice says the day and time the message was recorded
  • During playback, you can:

– go to the beginning of the current message by pressing the key once. – go to the previous message by pressing the key twice. – stop playback by pressing the Stop key . – interrupt playback by pressing the Pause key . Press the Pause key again to restart playback. – go to the next message by pressing the key.

8.14 Erasing Messages

  • 8.14.1 Erasing Messages One at a Time during Playback Start message playback as explained above.
  • When the message to be erased starts playing, press the delete key for 2 secs
  • During erase the internal voice will tell you that the message is being erased.
  • The machine will start playing the next message.
Page 33 of the Topcom 4056C user manual — 8.14 Erasing Messages
Page 33 · click to enlarge
Page 33
  • 8.14.2 Erase all messages One can also erase all heard messages at one time. This erases only the messages that have already been heard. New messages are not erased.
  • Press the delete key for 2 secs.
  • The internal voice confirms that the messages have been erased by saying how many new (unheard) messages there are.
  • 8.15 Memory Full If the memory is full, MEMORY FULL-LED will flash. If the answering machine is turned on and a call comes in, the machine will automatically play OGM 2 (answering machine function without recorded caller message). When listening to the messages, the internal voice will say that the memory is full and then play back the messages.
  • Erase all the messages after listening to them.
  • The memory is free again.
  • 8.16 Remote Operation The answering machine can only be operated remotely using a tough-tone phone (DTMF tone selection system).
  • Call your machine.
  • The answering machine picks up the line, you hear the outgoing message and a beep.
  • After the beep, slowly dial the VIP code (default 321).
  • You will hear two short beeps for confirmation.
  • Enter the next codes to use the desired function:

8.16.1 Listening to Messages • Press ‘2’ (listen to messages). The answer machine will play the messages.

  • During playback, you have the following options:
  • Press ‘2’ to stop playback.
  • Press ‘2’ to restart playback.
  • Press ‘3’ to go to the next message.
  • Press ‘1 1' to go to the previous message.
  • Press ‘1’ to repeat the current message.
  • Press ‘6’ to stop playback.
  • Press ‘7’ to erase the current message.

8.16.2 Erasing All Old Messages After listening to all messages, press ‘0’ to erase all messages.

8.16.3 Playing Outgoing Message Press ‘4’ to play the current outgoing message.

Page 34 of the Topcom 4056C user manual — 8.14 Erasing Messages
Page 34 · click to enlarge
Page 34
  • 8.16.4 Recording Outgoing Message
  • Press ‘9’ to select OGM 1 or OGM 2.
  • Press ‘5’ to start recording
  • A beep will indicate that you can start recording.
  • Say your message.
  • Press ‘6’ to stop recording. Note: Recording will be automatically interrupted after 2 minutes.
  • 8.16.5 Turning Answering Machine On/Off
  • Press the '9 ' key to switch on the answering machine.
  • Press the '8' key to turn off the answering machine.

8.16.6 Ending Remote Operation If you want to end remote operation, press ‘6’.

  • 8.17 Turning Answering Machine On Remotely If the answering machine is switched off, you can turn it on remotely.
  • Call your machine.
  • The machine will pick up automatically after 10 rings and play outgoing message 2.
  • Dial the VIP code (default 321) slowly during the message plays.
  • Press the '9' key.
  • The internal voice will say that the answering machine has been turned on.
  • Press ‘6’ to stop operation
Page 35 of the Topcom 4056C user manual — 9 Trouble shooting
Page 35 · click to enlarge
Page 35

9 Trouble shooting

Symptom Possible cause Solution

No display Batteries uncharged Check the position of the batteries Recharge the batteries

Handset turned OFF Turn ON the handset

No tone Telephone cord badly connected

Check the telephone cord connection

The line is occupied by another handset

Wait until the other handset hangs up

The icon flashes Handset out of range Bring the handset closer to

The base has no power supply

Check the mains connection to the base

The handset is not registered to the base

Register the handset to the base

Base or handset do not ring

The ringing volume is zero or low

Adjust the ringing volume

Tone is good, but there is no communication

The dialling mode is wrong

Adjust the dialling mode (pulse/tone)

Telephone does not react to pressing the keys

Manipulation error Remove the batteries and but them back in place

Keypad lock ON Turn OFF the Keypad Lock

Flash (R) Key does not work

Wrong Flash time Change the flash time

the base

Page 36 of the Topcom 4056C user manual — 11 Technical characteristics
Page 36 · click to enlarge
Page 36

10 Topcom warranty

10.1 Warranty period

The Topcom units have a 24-month warranty period. The warranty period starts on the day the new unit is purchased. The warranty on batteries is limited to 6 months after purchase. Consumables or defects causing a negligible effect on operation or value of the equipment are not covered. The warranty has to be proven by presentation of the original purchase receipt, on which the date of purchase and the unit-model are indicated.

10.2 Warranty handling

A faulty unit needs to be returned to a Topcom service centre including a valid purchase note. If the unit develops a fault during the warranty period, Topcom or its officially appointed service centre will repair any defects caused by material or manufacturing faults free of charge. Topcom will at its discretion fulfil its warranty obligations by either repairing or exchanging the faulty units or parts of the faulty units. In case of replacement, colour and model can be different from the original purchased unit. The initial purchase date shall determine the start of the warranty period. The warranty period is not extended if the unit is exchanged or repaired by Topcom or its appointed service centres.

10.3 Warranty exclusions

Damage or defects caused by incorrect treatment or operation and damage resulting from use of non- original parts or accessories not recommended by Topcom are not covered by the warranty. Topcom cordless phones are designed to work with rechargeable batteries only. The damage caused by the use of non-rechargeable batteries is not covered under warranty. The warranty does not cover damage caused by outside factors, such as lightning, water and fire, nor any damage caused during transportation. No warranty can be claimed if the serial number on the units has been changed, removed or rendered illegible. Any warranty claims will be invalid if the unit has been repaired, altered or modified by the buyer or by unqualified, non-officially appointed Topcom service centres.

11 Technical characteristics

Standard: DECT ( Digital Enhanced Cordless Telecommunications ) GAP ( Generic Access Profile ) Frequency range: 1880 MHZ to 1900 MHz Number of channels: 120 duplex channels Modulation: GFSK Speech coding: 32 kbit/s Emission power: 10 mW ( average power per channel ) Range: 300 m in open space /50 m maximum inhouse Base power supply: 230 V / 50 Hz for the base Handset Batteries: 2 rechargeable batteries AAA, NiMh 600mAh Handset autonomy: 100 hours in standby Talk time: 8 hours Charging time: 6-8 hours Normal conditions of use: +5 °C to +45 °C Dialling mode: Pulse / Tone

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
No displayBatteries unchargedCheck the position of the batteries Recharge the batteries p.35
No displayHandset turned OFFTurn ON the handset p.35
No toneTelephone cord badly connectedCheck the telephone cord connection p.35
No toneThe line is occupied by another handsetWait until the other handset hangs up p.35
The icon flashesHandset out of rangeBring the handset closer to p.35
The icon flashesthe base p.35
The icon flashesThe base has no power supplyCheck the mains connection to the base p.35
The icon flashesThe handset is not registered to the baseRegister the handset to the base p.35
Base or handset do not ringThe ringing volume is zero or lowAdjust the ringing volume p.35
Tone is good, but there is no communicationThe dialling mode is wrongAdjust the dialling mode (pulse/tone) p.35
Telephone does not react to pressing the keysManipulation errorRemove the batteries and but them back in place p.35
Telephone does not react to pressing the keysKeypad lock ONTurn OFF the Keypad Lock p.35
Flash (R) Key does not workWrong Flash timeChange the flash time p.35

Ask about the Topcom 4056C

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Topcom 4056C

Be the first to ask — other owners or our team will answer.

Original document

Topcom 4056C manual PDF

72 pages·983 KB·Telephone·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…