EN
Toshiba logo
Official user manual

Toshiba 1000

54 pages·3.2 MB·Power Supply·PDF·ENDEFRITNLJA
Toshiba 1000
Table of Contents 55 sections IMPORTANT NOTICE · UNINTERRUPTIBLE POWER SYSTEM · Manual’s Purpose and Scope · Contacting Toshiba International Corporation’s Customer Support Center · … ShowHide
Page 1 of the Toshiba 1000 user manual
Page 1 · click to enlarge
Page 1
Toshiba 1000 diagram (page 1)
Fig. 1
Page 2 of the Toshiba 1000 user manual — IMPORTANT NOTICE
Page 2 · click to enlarge
Page 2

IMPORTANT NOTICE

The instructions contained in this manual are not intended to cover all of the details or

variations in equipment, or to provide for every possible contingency concerning

installation, operation, or maintenance. Should further information be required or if

problems arise which are not covered sufficiently, contact your local Toshiba sales

office or (800) 231-1412 or by e-mail at toshibaups@tic.toshiba.com.

The contents of this instruction manual shall not become a part of or modify any prior or

existing agreement, commitment, or relationship. The sales contract contains the entire

obligation of Toshiba International Corporation (TIC) 's Uninterruptible Power Systems

(UPS) Division. The warranty contained in the contract between the parties is the sole

warranty of TIC's UPS Division and any statements contained herein do not create new

warranties or modify the existing warranty.

Any electrical or mechanical modifications to this equipment without prior

written consent of Toshiba International Corporation will void all warranties and

may void the UL/CUL listing. Unauthorized modifications can also result in

personal injury, death, or destruction of the equipment.

Page 3 of the Toshiba 1000 user manual — UNINTERRUPTIBLE POWER SYSTEM
Page 3 · click to enlarge
Page 3

UNINTERRUPTIBLE POWER SYSTEM

Complete the information below for the UPS received.

Unless otherwise specified on the warranty card, the warranty period for the UPS or

UPS part is 36 months from the shipment date (see TIC Bill of Lading).

Unless otherwise specified on the warranty card, the warranty period for a UPS battery

is 24 months from the shipment date (see TIC Bill of Lading).

Please complete the following information and retain for your records.

Job Number________________________________________________________
Model Number_____________________________________________________
Serial Number______________________________________________________
Application________________________________________________________
Shipment Date______________________________________________________
Installation Date____________________________________________________
Inspected By_______________________________________________________
Document Number57723-003

January, 2007

Page 4 of the Toshiba 1000 user manual — UNINTERRUPTIBLE POWER SYSTEM
Page 4 · click to enlarge
Page 4
Page 4 of the Toshiba 1000 user manual — UNINTERRUPTIBLE POWER SYSTEM
Page 5 of the Toshiba 1000 user manual — UNINTERRUPTIBLE POWER SYSTEM
Page 5 · click to enlarge
Page 5
Page 5 of the Toshiba 1000 user manual — UNINTERRUPTIBLE POWER SYSTEM
Page 6 of the Toshiba 1000 user manual — Manual’s Purpose and Scope
Page 6 · click to enlarge
Page 6

Manual’s Purpose and Scope

The purpose of this manual is to provide information on how to safely install, operate,

and maintain your TIC power electronics product. This manual includes a section of

general safety instructions that describes the warning labels and symbols that are used

throughout the manual. Read the manual completely before installing, operating, or

performing maintenance on this equipment.

The scope of this manual is to describe the requirements for an On-Line Uninterruptible

Power System (UPS). The UPS will supply a computer grade AC output sine wave

which is unaffected by the quality of the AC input. The input voltage is single phase and

the output voltage is single phase.

This manual and the accompanying drawings should be considered a permanent part of

the equipment and should be readily available for reference and review. Dimensions

shown in the manual are in metric and/or the English equivalent.

TIC reserves the right, without prior notice, to update information, make product

changes, or to discontinue any product or service identified in this publication.

Page 7 of the Toshiba 1000 user manual — Manual’s Purpose and Scope
Page 7 · click to enlarge
Page 7

TOSHIBA is a registered trademark of Toshiba Corporation. All other product or trade

references appearing in this manual are registered trademarks of their respective

owners.

Toshiba International Corporation (TIC) shall not be liable for direct, indirect,

special, or consequential damages resulting from the use of the information

contained within this manual.

This manual is copyrighted. No part of this manual may be photocopied or reproduced

in any form without the prior written consent of Toshiba International Corporation.

© Copyright 2006 Toshiba International Corporation.

All rights reserved.

Printed in the U.S.A.

Page 8 of the Toshiba 1000 user manual — Contacting Toshiba International Corporation’s Customer Support Center
Page 8 · click to enlarge
Page 8

Contacting Toshiba International Corporation’s Customer Support Center

Toshiba International Corporation’s Customer Support Center can be contacted to

obtain help in resolving any Uninterruptible Power System problems that you may

experience or to provide application information.

The center is open from 8 a.m. to 5 p.m. (CST), Monday through Friday. The Support

Center’s toll free number is US (800) 231-1412, Fax (713) 896-5212.

The email address is toshibaups@tic.toshiba.com.

You may also contact Toshiba International Corporation by writing to:

13131 West Little York Road

Attn: 1000 Series UPS Product Manager.

For further information on Toshiba International Corporation’s products and services,

please visit our website at www.toshiba.com/ind

Toshiba International Corporation · Houston, Texas 77041-9990

Page 9 of the Toshiba 1000 user manual — ICES-003
Page 9 · click to enlarge
Page 9

EMC Statements

complies with the conditions of a Class B digital device. The product has been

established as offering sufficient protection against dangerous interference for

installations in a residential area. Installation and use of the equipment should comply

with the instructions provided in order to avoid interference due to the amount of radio

frequency energy that is radiated and generated by the equipment.

TIC cannot assure that no interference will occur. Turn the unit on and off to help

determine if the radio or television reception is found to be influenced by harmful

interference from the equipment. If required, use one of the following measures to

minimize the negative effects of interference:

  • Place the receiving antenna in a separate location or orientation.
  • Increase the distance between the receiver and the equipment.
  • Ensure that your equipment and the receiver are on separate circuits.
  • Contact a technician experienced with radio and TV or a dealer for further

assistance.

ICES-003

This Class B Interference Causing Equipment meets all requirements of the Canadian

Interference Causing Equipment Regulations ICES–003. Cet appareil numérique de la

classe B respecte toutes les exigences du Reglement sur le matériel brouilleur du

Canada.

FCC Part 15

Page 10 of the Toshiba 1000 user manual — EMC Statements
Page 10 · click to enlarge
Page 10

Declaration of Conformity Request

Units labeled with a CE mark comply with the following standards and directives:

Harmonic Standards: EN 50091-1-1 and EN 50091-2.

EU Directives73/23/EEC, Council Directive on equipment designed for use within

certain voltage limits.

93/68/EEC, Amending Directive 73/23/EEC.

89/336/EEC, Council Directive relating to electromagnetic compatibility.

92/31/EEC, Amending Directive 89/336/EEC relating to EMC.

The EC Declaration of Conformity is available upon request for products with a CE

mark.

Page 11 of the Toshiba 1000 user manual — DANGER
Page 11 · click to enlarge
Page 11

General Safety Instructions

DO NOT attempt to install, operate, maintain or dispose of this equipment until you

have read and understood all of the product safety information and directions that are

contained in this instruction manual.

Safety Alert Symbol / Signal Words

The Safety Alert Symbol indicates that a potential personal injury hazard exists. The

symbol is comprised of an equilateral triangle enclosing an exclamation mark.

Signal Words

Listed below are the signal words that are used throughout this manual followed by their

descriptions and associated symbols. When the words DANGER, WARNING, and

information that must be carefully adhered to.

1. Danger — The word DANGER in capital letters preceded by the safety alert

symbol indicates that an imminently hazardous situation exists that, if not avoided,

will result in death or serious injury to personnel.

DANGER

Page 12 of the Toshiba 1000 user manual — CAUTION
Page 12 · click to enlarge
Page 12
2. Warning — The word WARNING in capital letters preceded by the safety alert

symbol indicates that a potentially hazardous situation exists that, if not avoided,

could result in death or serious injury to personnel.

WARNING

3. Caution/Attention — The word CAUTION or ATTENTION in capital letters

preceded by the safety alert symbol indicates that a potentially hazardous situation

exists that, if not avoided, may result in minor or moderate injury.

CAUTION / ATTENTION

4. The word CAUTION without the safety alert symbol indicates a potentially

hazardous situation exists which, if not avoided, may result in equipment and

property damage.

CAUTION

Page 13 of the Toshiba 1000 user manual — WARNING
Page 13 · click to enlarge
Page 13

Other warning symbols may appear in conjunction with the Danger, Warning, and

particular areas where special care and/or procedures are required in order to prevent

serious injury and possible death.

1. ELECTRICAL HAZARD SYMBOL – Indicates a hazard that may cause injury

from an electrical shock or burn. The symbol is comprised of an equilateral triangle

enclosing a lightning bolt.

2. EXPLOSION HARZARD SYMBOL – Indicates a hazard that may cause injury

from exploding parts. It is comprised of an equilateral triangle enclosing an

explosion image.

Special Symbols

Page 14 of the Toshiba 1000 user manual — Important Safety Instructions
Page 14 · click to enlarge
Page 14

Important Safety Instructions

This manual contains important instructions that should be followed during the

installation, maintenance, and operation of the UPS and its batteries to assure safe and

proper operation.

1. Turn off, lockout, and tagout all power sources before connecting the power wiring

to the equipment or when performing maintenance.

2. Hardwire type UPS units are not equipped with an over-current protection device,

nor do they have an output disconnect for the ac output. Therefore, a user-installed

circuit breaker should be provided between the UPS output and the load input.

3. The maximum ambient operating temperature is 104° F (40° C).
4. Battery servicing should be performed by a qualified Toshiba Representative only.
5. Unauthorized personnel should not service batteries.
6. Contact your nearest Toshiba authorized service center for battery replacement.

Qualified Personnel is one that has the skills and knowledge relating to the

construction, installation, operation, and maintenance of the electrical equipment and

has received safety training on the hazards involved (Refer to the latest edition of NFPA

70E for additional safety requirements).

Qualified Personnel shall:

1. Have read the entire operation manual.
2. Be trained and authorized to safely energize, de-energize, ground, lockout and tag

circuits and equipment, and clear faults in accordance with established safety

practices.

3. Be trained in the proper care and use of protective equipment such as safety shoes,

rubber gloves, hard hats, safety glasses, face shields, flash clothing, etc., in

accordance with established safety practices.

4. Be trained in rendering first aid.
5. Be knowledgeable of batteries and the required handling and maintenance

precautions.

Qualified Personnel ONLY!

Page 15 of the Toshiba 1000 user manual — DANGER
Page 15 · click to enlarge
Page 15

For further information on workplace safety visit www.osha.gov

WARNING

Misuse of this equipment could result in injury and equipment damage. In no event will

Toshiba Corporation be responsible or liable for either indirect or consequential damage

or injury that may result from the misuse of this equipment.

CAUTION

Do not dispose of the batteries in a fire. The batteries may explode.

CAUTION

Do not open or mutilate the batteries. Released electrolyte is harmful to the eyes and

skin and could also be toxic.

DANGER

A battery can present a risk of electrical shock and high short circuit current.

Page 16 of the Toshiba 1000 user manual — Important Safety Instructions
Page 16 · click to enlarge
Page 16

—Strict adherence to the following precautions is a requirement when working with

To be performed by Qualified Personnel only.

1. Verify that the UPS is off and that the power cord is disconnected from the power

source.

2. Remove watches, rings or other metal objects.
3. Use tools with insulated handles to prevent inadvertent shorts.
4. Wear rubber gloves and boots.
5. Do not place tools or any metal parts on top of batteries.
6. Determine if the battery is inadvertently grounded. If inadvertently grounded,

remove source of ground.

Contact with any part of a grounded battery can result in electrical shock.

The likelihood of shock will be reduced if such grounds are removed prior to

installation or maintenance.

batteries—

Page 17 of the Toshiba 1000 user manual — ATTENTION
Page 17 · click to enlarge
Page 17

Instructions Importantes Concernant

LA SÉCURITÉ CONSERVER CES INSTRUCTIONS

Cette notice contient des instructions importantes concernant la sécurité.

ATTENTION

Une battery peut présenter un risque de choc électrique, de brûlure par transfert d'

énergie.

ATTENTION

L' élimination des batteries est règlementèe. Consulter les codes locaux à cet effet.

Page 18 of the Toshiba 1000 user manual — Inspection/Storage/Disposal
Page 18 · click to enlarge
Page 18

Inspection/Storage/Disposal

CAUTION

Upon receipt of the UPS, an inspection for shipping damage should be performed. Use

attached to packing material.

Check the unit for loose, broken, bent or otherwise damaged parts. If damage has

occurred during shipping, keep all original crating and packing materials for return to

the shipping agent. The warranty does not apply to damage incurred during shipping.

Ensure that the rated capacity and the model number specified on the nameplate

conform to the order specifications.

During periods of non-use, the following guidelines are recommended for storage.

1. Power up the UPS and allow it to operate with no load for 24 hours to fully charge

the batteries.

2. Stop the unit.
3. Place the MCCB switch in the Off position.
  • For best results, store the UPS in the original shipping container and place on a

wood or metal pallet.

  • Storage temperature — -20 – 40° C (-4 – 104° F).
  • The optimum storage temperature is 21° C (70° F). A higher ambient temperature

will require recharging more frequently during storage.

Avoid the following storage locations:

Show 5 more labels / short text on this page
Inspection · Uncrating · Storage · Storage Preparation · Storing Conditions
Page 19 of the Toshiba 1000 user manual — Inspection/Storage/Disposal
Page 19 · click to enlarge
Page 19
  • Locations that are subject to extreme temperature changes or high humidity.
  • Locations that are subject to high levels of dust or metal particles.
  • Locations that are subject to excessive vibration.
  • Inclined floor surfaces.
  • If stored at an ambient temperature less than 20° C (68° F), recharge the batteries

every 9 months.

  • If stored at an ambient temperature of 20° – 30° C (68° – 86° F), recharge the

batteries every 6 months. • If stored at an ambient temperature of 30° – 40° C (86° – 104° F), recharge the batteries every 3 months.

Please contact your local or state environmental agency for details on disposal of

electrical components and packaging in your particular area.

It is illegal to dump lead-acid batteries in landfills or dispose of improperly.

Please help our Earth by contacting the environmental protection agencies in your area,

the battery manufacturer, or call Toshiba toll-free at (800) 231-1412 for more

information about recycling.

Storage Maintenance · Disposal

Page 20 of the Toshiba 1000 user manual — Installation Precautions
Page 20 · click to enlarge
Page 20

Installation Precautions

CAUTION

1. Install the unit in a well-ventilated location; allow at least 10 cm (4 inches) on all

sides for air ventilation and for maintenance.

2. Install the unit in a stable, level and upright position that is free of excessive

vibration.

3. Install the unit where the ambient temperature is within the range specified.
4. Do not install the UPS in areas that are subject to high humidity.
5. Do not install the UPS in areas that allow exposure to direct sunlight.
6. Do not install the UPS in areas that allow exposure to high levels of airborne dust,

metal particles, or flammable gases.

7. Do not install the UPS in areas near sources of electrical noise. Ensuring a proper

earth ground will reduce the effects of electrical noise and will reduce the potential

for electrical shock.

8. Do not install the UPS in areas that would allow fluids or any foreign object to get

inside the UPS.

9. The UPS generates and can radiate radio-frequency energy during operation.

Although RFI noise filters are installed inside of the unit, there is no guarantee that

the UPS will not influence some sensitive devices that are operating near by. If such

interference is experienced, the UPS should be installed farther away from the

affected equipment and/or powered from a different source than that of the affected

equipment.

10. The user should provide output over-current protection for hardwired UPS systems.
11. After ensuring that all power sources are turned off and isolated in accordance with

established lockout/tagout procedures, connect the power source wiring of the

correct voltage to the input terminals of the UPS.

Page 21 of the Toshiba 1000 user manual — CAUTION
Page 21 · click to enlarge
Page 21
12. Connect the output terminals of the UPS to the load (refer to NEC Article 300 –

Wiring Methods and Article 310 – Conductors For General Wiring). Size the

branch circuit conductors in accordance with NEC Table 310.16.

Conductor Routing and Grounding

1. Use separate metal conduits for routing the input power, output power, and control

circuits.

2. Follow the wire size and tightening torque specifications.
3. Always ground the unit to reduce the potential for electrical shock and to help

reduce electrical noise.

4. A separate ground cable should be run inside the conduit with the input power,

output power, and control circuits.

CAUTION

THE METAL OF CONDUIT IS NOT AN ACCEPTABLE GROUND.

Page 22 of the Toshiba 1000 user manual — Operating Precautions
Page 22 · click to enlarge
Page 22

Operating Precautions

CAUTION

1. The UPS should not be powered up until the entire operation manual has been read.
2. The voltage of the input power source must be within the range of +10% to -30% of

the rated input voltage. The input frequency must be within the rated input

frequency range. Voltages and frequencies outside of the permissible range may

activate the internal protection devices.

3. The UPS should not be used with a load that has a rated input that is greater than the

rated output of the UPS.

4. Do not use the UPS to provide power to motors that require high starting current or

with motors that require a long starting time, such as vacuum cleaners and machine

tools (over sizing the UPS for lock rotor current would be required).

5. Do not insert metal objects or combustible materials in the ventilation slots of the

UPS.

6. Do not place, hang, or paste any objects on the exterior surfaces of the UPS.
7. The capacitors of the UPS maintain a residual charge for a while after turning the

UPS off. The required discharge time for each UPS typeform is provided via a

cabinet label and a CHARGE LED. Wait for at least the minimum time indicated on

the label and ensure that the CHARGE LED has gone out before opening the door

of the UPS once the UPS power has been turned off.

8. Do not attempt to disassemble, modify, or repair the UPS. Call your Toshiba sales

representative for repair information.

9. Turn the power on only after attaching ALL of the covers.
10. Do Not remove any covers of the UPS when the power is on.
11. If the UPS should emit smoke or an unusual odor or sound, turn the power off

immediately.

Page 23 of the Toshiba 1000 user manual — CAUTION
Page 23 · click to enlarge
Page 23
12. The heat sink and other components may become extremely hot to the touch. Allow

the unit to cool before coming in contact with these items.

13. Warning signs should be placed on or near the load as a notification that the load is

being powered by the UPS.

14. Additional warnings and notifications shall be posted at the equipment installation

location as deemed required by Qualified Personnel.

WARNING

While operating in the inverter mode, placing the breaker in the OFF position will

switch the UPS to the battery backup mode. The output of the UPS will continue

uninterrupted to the load. The unit must be in the bypass mode at the time that the

breaker is placed in the OFF position for the UPS to shutdown power to the load. After an Emergency Power Off (EPO), do not reset the breaker until the UPS has been

CAUTION

fully discharged. The UPS could be damaged if the unit is not fully discharged before

the breaker is reset.

Page 24 of the Toshiba 1000 user manual — 1. Introduction
Page 24 · click to enlarge
Page 24

1. Introduction

The information provided in this manual covers single phase 1000 – 3000 VA

uninterruptible power systems (UPS). Included in this manual is information on the

installation, operation, safety precautions, shipping, and storage of the equipment.

Installation must be carried out in accordance with this manual. Electrical installations

must also follow local legislation and regulations. Only qualified personnel should

install this equipment. Failure to comply with the warnings and precautions could prove

to be fatal. 2. System Description

The purpose of the UPS is to protect sensitive systems from poor quality utility power,

complete loss of power, or other associated problems. System types include computers,

workstations, process control systems, telecommunications systems, sales terminals, or

other critical instrumentation.

Electrical interference may occur causing problems in AC power. Interference may

come from lightning, the power company, radio transmissions, or motors. Normal

operation of sensitive electrical equipment requires protection against power outages,

low or high voltage levels, frequency variations, differential and common-mode noises,

and transients.

In order to prevent power line problems from reaching critical systems and causing

damage to software, hardware or causing equipment to malfunction, the UPS helps by

maintaining a constant voltage, isolating critical load output, and cleaning the utility AC

power.

Page 25 of the Toshiba 1000 user manual — 1. Introduction
Page 25 · click to enlarge
Page 25

2.1 General Description

As a double conversion on-line UPS, it is able to supply uninterrupted, clean

single-phase power to your critical systems while keeping batteries charged

continuously, even if the utility power fails.

Other features of the UPS includes

  • Auto-Restart and Cold Start features
  • Programmable Load Shed Receptacle
  • Intelligent Charger with Rapid Charge in only 4 hours to 90%
  • Wide Input Voltage Window
  • Wide Input Frequency Window for Complete Generator Compatibility
  • Input Power Factor greater than 0.97
  • Output Power Factor 0.70
  • Multiple Languages LCD Display
  • Efficiency Optimizer Function – See detail explanation on page 4
  • Free Run Mode - See detail explanation on page 4.
  • Diagnostic Tests - See detail explanation on page 4
  • Optional Network Interface Card, RemotEye II
  • Optional Environmental Monitoring Device
  • No Cold Starts on first use ( safety purpose )

In the event that a power failure lasts longer than the UPS backup time, the UPS will

shut down. Upon power restoration, the UPS will restart automatically, which includes

output power being restored to the load and the start of battery recharge.

See following Figure 1 for systemic applicable of the UPS system.

Page 26 of the Toshiba 1000 user manual — 1. Introduction
Page 26 · click to enlarge
Page 26
Toshiba 1000 — 1. Introduction diagram (page 26)
Fig. 2 · 1. Introduction
Toshiba 1000 — 1. Introduction diagram (page 26)
Fig. 3 · 1. Introduction

Figure 1. Block diagram

  • An input filter reduces transients on the main supply.
  • For maintaining full battery charge, AC-power is rectified and regulated in the

rectifier feeding power to the inverter and battery converter.

  • DC power is converted to AC in the inverter and passes it on to the load.
  • Power to the load is maintained from the battery during a power failure.
  • The converter increases voltage for the inverter as required.

2.2 Efficiency Optimizer Function

The Efficiency Optimizer function is a new feature for the UPS that increases the cost

effectiveness of the UPS by minimizing power losses and reduces power consumption.

IGBT Control · SNMP Port/Dry Contact · IGBT Control

Page 27 of the Toshiba 1000 user manual — 1. Introduction
Page 27 · click to enlarge
Page 27

Alternating between bypass and on-line modes is achieved automatically and in

accordance with the conditions of the utility power. On-line mode may be used during

times of utility power irregularities. The bypass mode should be used when power flows

smoothly in order to obtain the greatest efficiency. Irregularities can be detected in less

than a second and the on-line mode can be reactivated immediately. Switching back to

online mode occurs when the input voltage exceeds ±10% (or ±15% selectable), when

the input frequency exceeds ±3Hz, or when no input line is available.

Although high efficiency is standard, the default operation is the on-line mode. From

the LCD display panel, Bypass can be activated as required or On-line operation can be

run permanently if preferred.

2.3 Free Run Mode

Free run mode is a mode of operation in which the output frequency does not match

input frequency. The UPS operates in free run mode when the input frequency is outside

of the selected input frequency range. When starting the UPS, the targeted frequency is

50 or 60 Hz ±0.25Hz. Refer to Section 4.3 to set up bypass availability while running in

free run mode.

2.4 Diagnostic Tests

When the UPS is started, a diagnostic test is executed automatically that checks the

electronics and battery, and reports any problems on the LCD display.

The advanced battery management system monitors the performance of the battery and

will indicate if battery replacement is required. The battery management system tests

the battery every 30 days of normal mode operation. A battery discharge test is

performed and reports any problems on the LCD display.

Except during the first 24 hours after startup while the UPS is in charging mode,

diagnostic tests can be performed manually from the front panel when required.

2.5 System Configuration

The UPS device and the internal backup battery make up the system. Depending on the

site and load requirements of the installation, available options may be utilized to create

a tailored solution.

Page 28 of the Toshiba 1000 user manual — 1. Introduction
Page 28 · click to enlarge
Page 28

Planning a UPS system should include the following considerations:

  • The total demand of the protected system shall dictate the output power rating (VA).

Allow a margin for future expansion or calculation inaccuracies from measuring

power requirements.

  • Backup time needed will determine the battery size needed. If the load is less than

the UPS nominal power rating then the actual backup time will be longer.

  • The following options are available:
  • External Battery Cabinets, and
  • Connectivity options (Remote Contact, SNMP/WEB card).

The following UPS models are available.

Model Backup time Internal

Recharge time to 90%

UPS 1000VA 7 min 4 hours

UPS 1500VA 6 min 4 hours

UPS 2000VA 7 min 4 hours

UPS 3000VA 6 min 4 hours

Additional External Battery Cabinets are available if more back-up time is needed.

batteries · capacity

Page 29 of the Toshiba 1000 user manual — 3. Storage
Page 29 · click to enlarge
Page 29

3. Storage

Please adhere to the following instructions if the UPS is not installed when received:

  • Store the equipment in its original packing and shipping carton.
  • Store the unit in a temperature of 15° C to 25° C.
  • Ensure that the equipment is fully protected from wet or damp areas and from moist

air.

In order to maintain the vitality of the batteries, ensure that the UPS is recharged every 6

months for at least 8 hours during storage.

Page 30 of the Toshiba 1000 user manual — 4. Installation
Page 30 · click to enlarge
Page 30

4. Installation

4.1 Environment

To ensure safe and proper operation, ensure that the installation conforms to the

following specifications.

Ensure that the installation location is consistent with the following:

  • Avoid extreme temperature and humidity. Maximal battery life can be attained with

a recommended temperature range of 15° C to 25° C.

  • Protect the equipment from moisture.
  • Space and ventilation requirements must be met. Ensure there is at least 100mm (4

inch) behind and 50mm (2 inch) on the sides of the UPS for ventilation.

  • Ensure that the front of the UPS remain supply clear for user access.

The External Battery Cabinets must be installed next to or underneath the UPS.

Page 31 of the Toshiba 1000 user manual — 4. Installation
Page 31 · click to enlarge
Page 31

4.2 Rear Panel Views

1000VA – 1500VA Tower Rear Panel

Toshiba 1000 — 4. Installation diagram (page 31)
Fig. 4 · 4. Installation

2000VA – 3000VA Tower Rear Panel

Toshiba 1000 — 4. Installation diagram (page 31)
Fig. 5 · 4. Installation
Page 32 of the Toshiba 1000 user manual — 4. Installation
Page 32 · click to enlarge
Page 32

1000 – 1500 VA Rack mount (2U) Rear Panel

Toshiba 1000 — 4. Installation diagram (page 32)
Fig. 6 · 4. Installation

2000 – 3000 VA Rack mount (2U) Rear Panel

Page 33 of the Toshiba 1000 user manual — 4. Installation
Page 33 · click to enlarge
Page 33

4.3 Connection to main supply and loads (1000 – 3000 VA)

The input cable is supplied with all models.

  • Ensure that the UPS is disconnected from the main supply and loads while

connecting the External Battery Cabinets.

  • Use the battery cable supplied with the External Battery Cabinet to connect the

External Battery Cabinet to the UPS. If more than one battery cabinet is required,

use the supplied cable.

  • A familiarity with the UPS parameter settings is required if changing the Battery

pack quantity as when using the External Battery Cabinets.

  • Connect the input cable to the UPS and connect the other end to a grounded outlet.

The batteries will charge automatically when connected to the main supply.

The UPS may be used immediately to power a load. However, the maximum

battery back-up time will not be available until the recommended 8-hour minimum

charge time has completed.

  • If a Site Wiring Fault is displayed, rotate the connector.
  • After charging the UPS, connect the load to the UPS.
  • Do not connect any devices to the UPS that may cause overloading of the UPS or

that draws half-wave rectified current, such as hair dryers or vacuum cleaners.

  • See section 5 Computer and Alarm Connections if computer or alarm (rear panel)

connections are used.

  • The installation is now complete.
Page 34 of the Toshiba 1000 user manual — 4. Installation
Page 34 · click to enlarge
Page 34
Toshiba 1000 — 4. Installation diagram (page 34)
Fig. 7 · 4. Installation

Figure 2 Example of Installation of Plug & Play products.

Page 35 of the Toshiba 1000 user manual — ON/OFF
Page 35 · click to enlarge
Page 35

4.4 Front Panel Settings

Listed below are the default settings of the primary UPS parameters.

Settings Options Default Remarks 1) O/P VOLT SET (output voltage set)

100V/110V/115V/120V/127V 208/220/230/240 Vac 120V 230V

120V (FOR LV series) 230V (FOR HV series)

2. I/P FREQ SET (input frequency setting)

+/- 2% +/- 5% +/- 7%

+/- 5% Input Frequency range in Free Run mode

3. I/P BYPASS SET (input bypass setting)

+/- 10% +10% -15% +15% -20%

Input Voltage range when Bypass mode is on

4) FREE RUN SET

If ON, enable UPS runs on Asynchronous mode. For example: If input freq 55Hz output freq stays at 60Hz. If OFF, disable UPS runs on synchronous mode. For example: If input freq 55Hz, UPS will go to battery mode. 5) HE MODE SET

ON/OFF

ON

If ON, enable UPS runs in High efficiency mode. The unit will be in bypass mode with 95% or higher efficiency. If OFF, the unit will be in the online mode with 85% efficiency. 6) MANUAL BYPASS

ON/OFF

OFF

ON/OFF OFF If ON, enable UPS switch to Bypass mode immediately.

+10% -15%

Page 36 of the Toshiba 1000 user manual — 14) RS232 CONTROL
Page 36 · click to enlarge
Page 36

Settings Options Default Remarks 7) OUTLET SETTING

GROUP1/GROUP2 Option 1: 1 On /2 On Option 2: 1 Off /2 On Option 3: 1 Off /2 Off Option 4: 1 On /2 Off

This is a load-shed feature.

8)BATTERY TEST TEST?

Perform battery test immediately

9) SILENCE SET

ON/OFF

OFF

10)BAT CABINET SET

0. EXT B. PACKS 1: EXT B. PACKS 2: EXT B. PACKS

Shown options when battery Cabinets are connected

11) SITE FAULT SET

Alarm on main computer connected at wrong polarity or Installation to main supply without group. 12) LANGUAGE ENGLISH GERMAN FRENCH SPANISH ITALIAN

ENABLE/DISABLE

DISABLE

ENGLISH

13. GENERATOR ON/OFF OFF If ON, UPS will work with a very large range of voltages and frequencies, without switching back and forth from Line battery mode.

14) RS232 CONTROL

ENABLE/CHANGE ENABLE Option to enable and disable the RS232 port. USB share the communication line with RS232. Only one option may be used at a time.

Complete the installation entirely before changing the default settings or connecting a load to the

UPS.

Option 1

Page 37 of the Toshiba 1000 user manual — 5. Computer and Alarm Connections
Page 37 · click to enlarge
Page 37

5. Computer and Alarm Connections

At the rear of the UPS is an interface that allows direct communication with a computer

system (see figure 2). There is a RS232 serial data interface, a USB data interface, and

an emergency power off switch. The RS232 port and the USB interface cannot be used

simultaneously.

In addition there is an optional interface slot that allows for the installation of

communications cards. It may be used in parallel with either the RS232 or USB ports.

An SNMP/WEB card is available for the optional interface slot that allows for the

RemotEye II to manage and monitor the system over a network or over the internet.

5.1 RS-232 Standard Interface Port

Only the communication cable provided with the UPS may be used to connect the UPS

to a computer when using the RS232 port of the UPS. Ensure that the operating system

of the computer supports RS232 communications. Other advanced power protection

solutions, such as SNMP, are available from your dealer.

The RS-232 interface uses a 9-pin D-sub connector. The names and functions of the port

pins are listed in the following table.

Toshiba 1000 — 5. Computer and Alarm Connections diagram (page 37)
Fig. 8 · 5. Computer and Alarm Connections

DB9 Female Connector Outline

Pin # Signal Direction (re UPS) Functions

2 TxD Output TxD Output

3 RxD Input RxD / Inverter Off Input

6 Output Ac Fail Output

8 Output Low Battery Output

9 Output 8–24 VDC Power

Table 1RS232 Pin Out Signal

(facing connector) · 5 Common Common

Page 38 of the Toshiba 1000 user manual — 5. Computer and Alarm Connections
Page 38 · click to enlarge
Page 38

5.2 Dry Contact Interface (optional card)

DB9 Male Connector Outline

Toshiba 1000 — 5. Computer and Alarm Connections diagram (page 38)
Fig. 9 · 5. Computer and Alarm Connections

Pin # Description I/O Type

1 UPS fail, relay contact, normally open, active close. output

2 Summary alarm, relay contact, normally open, active close.

One of the following signals activate this signal:

1. Output fault
2. Bus fault
3. Over temperature
4. Overload
5. Over Charging
6. Battery test fail
7. Charger failure

3 GND for secondary

4 Remote shutdown input

6 Bypass active, normally open, active close output

7 Battery low, normally open, active close output

8 Battery mode shutdown input

9 Utility fail, normally open, active close output

Table 2DryContact Pin Out Signal Chart

5.3 USB Port

Connecting the UPS to a computer using the USB port of the computer requires USB

compliant hardware, PC operating system support, and a UPS driver. The RS232 serial

(facing connector) · output · 5 Common

Page 39 of the Toshiba 1000 user manual — 5. Computer and Alarm Connections
Page 39 · click to enlarge
Page 39

port cannot be used when using the USB port. The USB cable is a standard cable and

may be purchased separately.

5.4 EPO Port (emergency power off)

A customer-supplied switch located remotely may be used to open the EPO connection

and force the UPS output receptacles to be switched off. The EPO function shuts down

the equipment immediately. An EPO will not provide an orderly shutdown. The UPS

will have to be manually restarted in order to regain power to the outlets.

After an Emergency Power Off (EPO), do not reset the breaker until the UPS has been

fully discharged. The UPS could be damaged if the unit is not fully discharged before

the breaker is reset.

5.5 Network Transient Protector

The network transient protector, located on the back panel, has both IN and OUT RJ45

10 baseT jacks and will protect a single network connector. Connect the input connector

to the jack labeled IN, and the output connector to the jack labeled OUT.

5.6 Load Segments

The sets of receptacles known as load segments provide organized shutdown and

startup of the equipment. Less critical equipment can be turned off during power

outages saving battery power for critical loads. The load group status can be viewed

from the LCD display and can be changed if necessary.

Toshiba 1000 — 5. Computer and Alarm Connections diagram (page 39)
Fig. 10 · 5. Computer and Alarm Connections

Load 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%

1000VA Backup (min) 150 56 38 30 23 19 15 12 10 7

1500VA Backup (min) 80 37 21 19 18 15 13 11 8 6

2000VA Backup (min) 150 68 38 26 19 14 11 9 8 7

3000VA Backup (min) 80 40 25 19 15 12 9 8 7 6

Page 40 of the Toshiba 1000 user manual — 6. User’s Guide to Operations
Page 40 · click to enlarge
Page 40

6. User’s Guide to Operations

Normal ongoing UPS operation requires little or no user input. Startup and shutdown requirements of the user are discussed in this section.

6.1 UPS Startup and Shutdown

  • Ensure that installation is correct and that the input power cable is connected to a

properly grounded outlet.

  • Start the UPS by pressing the On/Off button on the front panel.
  • The UPS will start the inspection of internal functions, main synchronization, and

inverter startup. A successful completion allows for output power via the outlets.

  • During the startup inspection the LCD will display Ready On. The LED will light

up when output power has started and the LCD display will show Line Mode.

  • Switch on the load.

Shutting Down the UPS

  • Shut off and disconnect the load.
  • Press and hold the UPS On/Off button for five seconds. The alarm will sound and

the UPS will shut down.

  • The LCD will momentarily display UPS OFF.

6.2 Button Operation

1. “ ” is the Load ON/OFF button.

(a) Press and hold the Load ON/OFF button for at least 3 seconds to turn on the UPS.

(b) While the UPS is operating, press and hold the Load ON/OFF button for at least 3 seconds to turn off the UPS.

Starting the UPS

Page 41 of the Toshiba 1000 user manual — 6. User’s Guide to Operations
Page 41 · click to enlarge
Page 41
2. “

” is the Enter button.

(a) Press and hold the Enter button for at least 2 seconds to read the parameter settings of the UPS. Press the Enter button again to read the next parameter.

(b) Ten seconds of inactivity will return the display to the original status.

3. “ ” is the Function button.

(a) Press and hold the Function button for at least 2 seconds to access the selectable

parameters. Press the Function button again to view the next parameter.

(b) Press the Enter button to view or change the displayed parameter.

(c) Ten seconds of inactivity will return the display to the original status.

6.3 Control Panel Functions The front panel is composed of five LED indicators, an LCD screen, and a speaker for audible alarms.

ON/ — is on when the UPS is turned on (green).

ON-LINE/ — is on when in the Normal or Static Bypass modes. Also indicates

that there is voltage at the output terminals (green).

ON-BAT/ — is on while operating in the Battery mode.

BYPASS/ — is on while operating in the Bypass mode (yellow).

ALARM/ — is on during active UPS internal errors (red). FAULT is accompanied by an audible alarm. Press any of the front panel buttons to cancel the alarm.

Page 42 of the Toshiba 1000 user manual — 6. User’s Guide to Operations
Page 42 · click to enlarge
Page 42

Status of the UPS, measurements, and alarms are all indicated on the LCD screen.

Rack Unit Tower Unit

Figure 3 Control panel

6.4 Normal Display

The UPS status is shown in the normal display mode. The UPS Meters display and the

Setting display may be accessed by pressing the Return button on Tower Unit and

FUNC button on the Rack Unit.

6.5 UPS Meters Display

Listed below are the parameters available for viewing from the UPS meters display.

Press this button to scroll through the parameters.

O/P VOLT= xxx.xV Shows Output AC Voltage

O/P FREQ= xx.x Hz Shows Output Frequency

I/P VOL T= xxx.xV Shows Input AC Voltage

I/P FREQ= xx.x Hz Shows Input Frequency

BAT VOLT= xx.xV Shows Battery Voltage

O/P LOAD%= xx% Shows Load % of Max Load

O/P W= xW Shows Output Watts

O/P VA= xVA Shows Output VA

O/P CURR= xA Shows Output Current

LCD Message Description

Page 43 of the Toshiba 1000 user manual — 6. User’s Guide to Operations
Page 43 · click to enlarge
Page 43

BACKUP TIME= xx min Shows Estimated Backup Time in Minutes

BAT CHARG= xx% Shows Approximate Percentage of Battery Capacity

TEMPERATURE= xxC Shows Approximate Ambient Temperature

BAT PACK NUM= x Shows External Battery Pack Number

RATING = xxxxVA Shows UPS Rating

CPU VERSION xx.x Shows CPU Version

6.6 UPS Configurations

1. Parameter settings may be viewed from the UPS Settings display.
2. To enter the configuration mode, press and hold the Function button for one second.

The first configuration parameter will be shown on the LCD display.

3. Press the Function button again to scroll through the remaining parameters.
4. Press the Enter button to select a displayed parameter.
5. Press the Function button to scroll through the options for the selected parameter.

Press the Enter button to select the setting.

6. If prompted to save the selection, press the Enter button to either confirm or save

the selection. See the table on page 12 for a complete listing of the user-settable

parameters.

7. If there is no user input for ten seconds, the UPS will exit the configuration mode

and return to normal mode displaying Line mode.

Page 44 of the Toshiba 1000 user manual — 6. User’s Guide to Operations
Page 44 · click to enlarge
Page 44

6.7 UPS Manual Test

Manual UPS and Battery tests may be performed from the UPS configuration screen.

Tests may be performed when the battery is not being charged.

To run the battery test scroll to the “Manual Bat Test” parameter press the Enter button

twice.

** NoteIn order for the UPS to operate normally, Manual Bypass should always be set

to OFF because the load will not be protected by the unit when Manual Bypass is ON.

*** Note: Turn off the UPS and keep the AC power on to use the Generator function.

(go to normal mode for \Generator\OFF).

6.8 Interpreting UPS Messages

Troubleshooting procedures described here provide instructions to be used to isolate

UPS malfunctions.

Start the troubleshooting procedure in the event of a control panel alarm.

6.9 Audible Alarms

  • While operating on battery power (ON BAT LED is on) the UPS will beep once at

5-second intervals.

  • While operating on battery power and the battery power is low (ON BAT LED is

flashing) the UPS will beep twice at 5-second intervals.

  • In the event of an internal fault with an active alarm (ALARM LED is on), the UPS

will provide a constant audible alarm and display an error message on the LCD

display.

  • While operating in the Bypass mode (BYPASS LED is on) the UPS will not beep.

6.10 Silencing an Alarm

With the exception of a LOW BATTERY Alarm, pressing any of the front panel buttons

will turn off the alarm. Select Silent Alarm Mode to disable all audible alarms.

Page 45 of the Toshiba 1000 user manual — 6. User’s Guide to Operations
Page 45 · click to enlarge
Page 45

6.11 Troubleshooting

Displayed on LCD Audible Alarm Alarm Description What You Should Do Output Overload Two Beeps/sec The UPS is overloaded (in

Remove loads from the UPS; least to most critical. If this solves the problem, the UPS will return to normal operation.

Line Mode). More power required than the UPS can provide. The UPS operates in bypass.

Battery Test No Beeps Battery test active. No action needed.

User Notification only.

Over-Charge Constant Beep Overcharged Batteries. Turn off loads. Turn off UPS. Call service @ 1-877-867-8773 Low Battery 2 Beeps/5 sec UPS operating on Battery Power and will shut down soon due to low battery voltage.

The unit will restart Automatically when acceptable power returns.

On-Battery 1 Beep/5 sec UPS operating on Battery Power.

Save your data and perform a controlled shutdown. Charger Failure Constant Beep Failed Charger. Call service @ 1-877-867-8773

Over-Temperature Constant Beep High ambient

Ensure that the UPS fans and vents are not blocked, and that the ambient temp. is < 40° C. If problem persists call service @ 1-877-867-8773 Output Short Constant Beep Output short circuit. Call service @ 1-877-867-8773 High output Voltage Constant Beep High output voltage. Call service @ 1-877-867-8773 Low Output Voltage Constant Beep Low output voltage. Call service @ 1-877-867-8773

Temperature.

Bus Fault 2 Beeps/sec High internal DC bus Voltage.

Turn off loads. Turn off UPS. Call service @ 1-877-867-8773 Site Wiring Fault 1 Beep/sec Voltage detected between neutral and ground.

UPS main connector wrong polarity. Rotate the connector (Schuko-electric contact). UPS installed to main supply without ground. See section 4.4 for information on how to disable the Site wiring alarm.

Line Abnormal 1 Beep/sec Wrong AC Line backed up during auto restart.

Page 46 of the Toshiba 1000 user manual — 7. Maintenance
Page 46 · click to enlarge
Page 46

7. Maintenance

With a minimal amount of maintenance you can expect years of satisfactory operation

from the UPS unit. The most critical issues for the reliability of the UPS are

environmental issues. Ensure that the temperature and humidity are always in

accordance with the specifications and keep the area around the unit clean and dust free.

The typical battery lifetime is 4 years when operated at 25° C.

Check the back-up time capability of the UPS/battery at 6 to 12 month intervals to

ensure adequate support for the application.

Page 47 of the Toshiba 1000 user manual — UT1A1A010C6 UT1A1A015C6 UT1A1A020C6 UT1A1A030C6
Page 47 · click to enlarge
Page 47

8. Technical Specifications

8.1 Power Range 1000-3000 VA (120V)

Tower US 120V Model

UT1A1A010C6 UT1A1A015C6 UT1A1A020C6 UT1A1A030C6

UT1A1A010C6R KB2

UT1A1A015C6R KB2

UT1A1A020C6R KB2

UT1A1A030C6R KB2

Input Voltage 120 VAC (80 – 144 V) Voltage Range +20% to -33% Capacity (VA) 1000 VA 1500 VA 2000 VA 3000 VA Capacity (W) 700 W 1050 W 1400 W 2100 W Frequency 50 / 60 Hz auto sensing Power Factor Greater than 0.97 Topology True on-line Double conversion Input PF correction Output Voltage 120 VAC Frequency 50 / 60 Hz auto sensing Wave Form Sine wave, zero transfer time Load Power Factor

Rated Current 8.3 A 12.5 A 16.6 A 25 A Overload Capacity

125% for 1 min 150% for 10 sec

Crest Factor 3.0 at full load Battery DC Voltage (Tower & 2U)

36 V / 12 V 9 AH x 3 72V / 12 V 7.2AH x 6 72V / 12 V 9AH x 6 Backup Time (Tower & 2U)

6 min (full load) Interface RS-232 and USB standard RemotEye II® and EMD option Physical Dimensions (Tower)

7 min (full load)

6 min (full load)

7 min (full load)

16.5”L x 6.0”W x 9.4”H 16.7"L x 8.9"W x 14.2"H

16.7”L x 16.9”W x 3.5”H 25.0"L x 16.9"W x 3.5"H

35.6 lbs / 37.6 lbs 37.4 lbs / 37.6 lbs 68.4 lbs / 69.5 lbs 72.6 lbs / 71.5 lbs

Line Cord 5-15P 5-20P L5-30P Receptacles (Tower/2U)

NEMA 5 - 15 P (6 / 6) NEMA 5-15 P (12 / 4)

0. 40 ° C (32 - 104 ° F)

Altitude 11500 ft (3500 m) above sea level Warranty Three years on electronics Two years full replacement on battery (See Toshiba warranty policy for full details.)

Show 8 more labels / short text on this page
Rack- mount (2U) · US 120V Model · Efficiency AC/DC/AC · Greater than 86% · Dimensions (2U) · Weight (Tower/2U) · Environ- ment · Operating Temperature
Page 48 of the Toshiba 1000 user manual — IEC 320
Page 48 · click to enlarge
Page 48

8.2 Power Range 1000-3000 VA (230V)

Tower International 230V Model UT1E1E010C6 UT1E1E015C6 UT1E1E020C6 UT1E1E030C6

International 230V Model UT1E1E010C6R KB2

UT1E1E015C6R KB2

UT1E1E020C6R KB2

UT1E1E030C6R KB2

230 VAC (161 – 276 V)

Capacity (VA) 1000 VA 1500 VA 2000 VA 3000 VA Capacity (W) 700 W 1050 W 1400 W 2100 W Frequency 50 / 60 Hz auto sensing Power Factor Greater than 0.97 Topology True on-line, Double conversion Input PF correction Output Voltage (International)

230 VAC

Frequency 50 / 60 Hz auto sensing Wave Form Sine wave, zero transfer time Load Power Factor

4.3 A 6.5 A 8.7 A 13 A

125% for 1 min., 150% for 10 sec.

Crest Factor 3.0 at full load Battery DC Voltage (Tower & 2U)

36 V / 12 V 9 AH x 3 72V / 12 V 7.2AH x 6 72V / 12 V 9AH x 6 Backup Time (Tower & 2U)

6 min (full load) Interface RS-232 and USB standard RemotEye II® and EMD option Physical Dimensions (Tower)

7 min (full load)

6 min (full load)

7 min (full load)

16.5”L x 6.0”W x 9.4”H 16.7" L x 8.9" W x 14.2" H

16.7”L x 16.9”W x 3.5”H "25.0""L x 16.9""W x 3.5""H"

35.6 lbs / 37.6 lbs 37.4 lbs / 37.6 lbs 68.4 lbs / 69.5 lbs 72.6 lbs / 71.5 lbs

IEC 320

IEC 320 (4 / 4) IEC 320 (8 / 8)

0. 40 ° C (32 - 104 ° F)

Altitude 11500 ft (3500 m) above sea level Warranty Three years on electronics Two years full replacement on battery (See Toshiba warranty policy for full details.)

Standards - SafetyEN50091-1-1, Emissions: EN50091-2, Immunity: EN50091-2 B (1000-1500VA)
Show 14 more labels / short text on this page
Rack- mount (2U) · Input Voltage (International) · Voltage Range (International) · +20% to -30% · Efficiency AC/DC/AC · Greater than 86% · Rated Current (International) · Overload Capacity · Dimensions (2U) · Weight (Tower/2U) · Line Cord (International) · Receptacles (Tower/2U) International · Environ- ment · Operating Temperature
Page 49 of the Toshiba 1000 user manual — (UNINTERRUPTIBLE POWER SYSTEM)
Page 49 · click to enlarge
Page 49

9. Warranty Information

TOSHIBA INTERNATIONAL CORPORATION

LIMITED WARRANTY POLICY

(48 contiguous U.S. States, Canada & Mexico)

(UNINTERRUPTIBLE POWER SYSTEM)

TOSHIBA INTERNATIONAL CORPORATION (“TIC”) warrants that any Uninterruptible Power System (“UPS”) and Uninterruptible Power System Battery (“BATTERY”) (internal UPS battery and/or external battery cabinet) sold by TIC to an end user (“User”) shall be free of defects in material and workmanship. This warranty applies to all UPS series in table below:

UPS Unit Battery UPS Series Unit kVA UPS Warranty (1)

1000 1.0, 1.5, 2, 3 36 months from shipment

24 months from shipment

No, Depot Depot Only

Note (1) Shipment date is determined by date on the TIC Bill of Lading. Note (2) For 1000 Series UPS the warranty applies if the units are sent and returned (paid for) by the user to/from the Toshiba Plant or a Toshiba designated Authorized Service Center. Note (3) Shipment date is determined by date on the TIC Bill of Lading * 24 month full replacement, 36 month pro-rated warranty (5 yr total) Note (4) For 1000 Series UPS the warranty applies if the units are sent and returned (paid for) by the user to/from the Toshiba Plant or a Toshiba Designated Authorized Service Center. Note (5) Toshiba Service dispatch available at normal business hours. Contacting Toshiba is possible 24 hours 7 days a week. User can purchase 24x7 dispatch programs offered through TIC’s Service Department. TIC also encourages users to review TIC’s UPS Preventative and Scheduled Maintenance/Parts Programs for Premium coverage. If any UPS, UPS parts, and/or BATTERY fail to conform or is defective then TIC, at its option, will repair or replace it at the premises of the User (On-Site), The warranty period for a UPS or a UPS part is 12-36 months from shipment except for cases stated in table above. The warranty period for the BATTERY is 24 months from shipment except for cases stated in the table above.

Show 7 more labels / short text on this page
Toshiba Dispatch (5) · On-Site · Battery Warranty (3) · On-Site · (2) · (4) · No, Depot
Page 50 of the Toshiba 1000 user manual — LIMITATIONS AND EXCLUSIONS
Page 50 · click to enlarge
Page 50

LIMITATIONS AND EXCLUSIONS

1. This limited warranty shall not cover the UPS, UPS parts, or BATTERY during their respective warranty periods, if the following storage, maintenance, installation, operating conditions are not met throughout the warranty periods (5 conditions below):

Valve Regulated Lead Acid (VRLA) Batteries for Toshiba UPS Required Operating, Installation, and

1. Temperature Annual Average Temperature is to be 77 ° F (25 ° C) with no greater temperature of 89 ° F (32 ° C) for more than 30 days Maximum Number of Cycles (24 Months)*** Discharge Time Battery > 9AHr Battery < 9AHr 30 min 20 69 15 min 25 86 10 min 32 110 5 min 38 130
2. Maximum # of Full Charge/Discharge Cycles

*** > 9AHr Typically extended runtimes < 9AHr Typically Single Phase Systems.

3. Storage While UPS is in Transit or in storage, it must always be in a suitable temperature (as stated above) 4. External Battery Parallel battery string applications must be approved by TIC in writing
5. Idle Batteries User must recharge the batteries if not in use (charged) for more than 6 months
Toshiba 1000 — LIMITATIONS AND EXCLUSIONS diagram (page 50)
Fig. 11

Credit for Replacement Battery When Approved Warranty Time from Shipments UPS Batteries Cost to Customer Months % Credit % List Price 0-24 100 0 25-30 55 45 31-36 45 55 37-42 35 65 43-48 25 75 49-54 15 85 55-60 5 95

Maintenance Conditions

Page 51 of the Toshiba 1000 user manual — LIMITATIONS AND EXCLUSIONS
Page 51 · click to enlarge
Page 51

2. This Warranty does not cover damage or defect caused by misuse, improper application, wrong or inadequate electrical current/voltage/frequency, inadequate connections, inadequate water or drain services, user negligence, repair by non-Toshiba designated personnel, accident during shipment, tampering, alterations, a change in UPS and/or BATTERY location or application, exposure to the elements, acts of God, force nature, theft, sabotage, installation contrary to TIC's recommendations or specifications (Published Operation Manuals), also if serial numbers have been altered, defaced, or removed. 3. Repair or replacement of a defective UPS, UPS part, and/or BATTERY does not extend the respective original warranty period. All defective UPS, UPS parts, and/or BATTERIES shall be the property of TIC upon replacement. 4. This warranty shall constitute the sole and exclusive remedy of all purchasers and users of the UPS, UPS part, and/or BATTERY. TIC’s responsibility for UPS, UPS Parts, and/or BATTERY shall not exceed one times the net UPS and/or BATTERY purchase price. TIC HEREBY EXPRESSLY DISCLAIMS ALL OTHER EXPRESS, STATUTORY AND IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

PROCEDURE User must contact TIC via e-mail upsservice@tic.toshiba.com, or phone 1-800-231-1412, no later than 90 days after User’s discovery of occurrence or defect in UPS, UPS part, and/or BATTERY but in no event after the expiration of the respective warranty period. Subject to the limitations of this policy and product type, TIC service or TIC service representative shall repair/replace the UPS/part warranted hereunder, without charge for material, labor (on-site except in cases presented herein). If TIC determines that the requested repair is not covered under this limited warranty policy, then TIC shall advise customer and quote cost of repair. Repair charges shall be based on service parts price and prevailing service charges at the time of repair. If the case in process is a BATTERY (stand-alone and/or cabinet) TIC will use its published Battery Diagnostic Document to evaluate warranty applicability. First, TIC will make sure that the storage, maintenance, installation, and operating conditions were met; then the BATTERY capacity will be tested in accordance with the “performance test” guidelines IEEE STD 450. If the BATTERY fails to deliver 70% of its rated capacity it shall be deemed defective and be replaced. Either float or cyclic service will be used to determine the warranty credit (as per published Battery Diagnostic Document). The typical credit applied will be as in the table above.

MODIFICATIONS No representative, salesperson, agent, distributor, or employee of TIC is authorized to modify any of the terms of this warranty, unless modifications are made in writing and signed by an authorized TIC officer.

Page 52 of the Toshiba 1000 user manual — LIMITATIONS AND EXCLUSIONS
Page 52 · click to enlarge
Page 52

THIS WARRANTY REPRESENTS THE ENTIRE AGREEMENT BETWEEN TIC AND USER WITH RESPECT TO THE SUBJECT MATTER HEREIN AND SUPERSEDES ALL PRIOR OR CONTEMPORANEOUS ORAL OR WRITTEN COMMUNICATIONS, REPRESENTATIONS, UNDERSTANDINGS OR AGREEMENTS RELATING TO THIS SUBJECT.

End User:

Model Number:

Serial Number:

Startup DateWarranty End Date:
Page 53 of the Toshiba 1000 user manual — LIMITATIONS AND EXCLUSIONS
Page 53 · click to enlarge
Page 53
Page 53 of the Toshiba 1000 user manual — LIMITATIONS AND EXCLUSIONS
Page 54 of the Toshiba 1000 user manual — LIMITATIONS AND EXCLUSIONS
Page 54 · click to enlarge
Page 54
Toshiba 1000 — LIMITATIONS AND EXCLUSIONS diagram (page 54)
Fig. 12
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Toshiba 1000

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Toshiba 1000

Be the first to ask — other owners or our team will answer.

Original document

Toshiba 1000 manual PDF

54 pages·3.2 MB·Power Supply·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…