EN
Toshiba logo
Official user manual

Toshiba TLP-ET1U

50 pages·4.4 MB·Projector·PDF·ENDEFRITNLJA
Toshiba TLP-ET1U
Table of Contents 80 sections OWNER’S MANUAL 3LCD PROJECTOR TLP-ET1B TLP-ET1E TLP-ET1U · CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS PROVIDED IN · 6. Water and Moisture · S3125A · … ShowHide
OWNER’S MANUAL 3LCD PROJECTOR TLP-ET1B TLP-ET1E TLP-ET1Up.1CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS PROVIDED INp.36. Water and Moisturep.3S3125Ap.5LABEL LOCATIONSp.6TLP-ET1Bp.6IMPORTANT PRECAUTIONSp.7Save Original Packing Materialsp.7Moisture Condensationp.7Avoid Volatile Liquidp.7LCD Panelp.7EXEMPTION CLAUSESp.7Copyrightsp.8Disposalp.8Notational Conventions Used in This Manualp.8Checking the package contentsp.8(1)p.10(6)p.10(3)p.10(7)p.10(5)p.10(9) (10)p.10(8)p.10(11)p.10(15)p.10(12)p.10(14)p.10(13)p.10Parts on the control panel and remote controlp.11Control panel Remote controlp.11YP B P R /AVp.11(2)p.12(5) (6)p.12Preparing and using the remote controlp.13Loading batteries into the remote controlp.13Operating the remote controlp.13Placing the projectorp.14Connecting a video devicep.15VCRp.15Connecting an input source device (Continued)p.16Connecting a DVD player with component video terminalsp.16Connecting a computerp.16TEMP FAN LAMP ONp.17Turning the power onp.18Safety lockp.18Turning the power offp.19FAN TEMP LAMP ONp.19PRECAUTIONSp.19Projectingp.20Cutting off the sound/Pausing the picturep.26Cutting off the sound temporarily (Mute)p.26Cutting off both the picture and sound temporarily (Sleep)p.26Pausing the picture (Freeze)p.26Switching to surround soundp.27Calling up a user profilep.29Picture adjustment menup.32Audio adjustment menup.34Default setting menup.35USp.35Status display menup.36User memory menup.37LIVINGp.38USER MEMORY2p.38USER MEMORY3p.38Lens cleaningp.41Replacing air intake and exhaust fans, and air filterp.41Trouble indicationsp.45ON LAMP TEMP FANp.45No powerp.45Lamp went out during usep.45Power went out during use, or won’t come onp.45Power went out during usep.45Before calling service personnelp.46Specificationsp.47List of general specificationsp.47List of supported signalsp.48XGA_60 XGA_70 XGA_75 XGA_85p.48SXGA3_60 SXGA3_75 SXGA3_85p.48I List of supported signals (Y/P B /P R signals)p.49Pin assignment of COMPUTER terminalp.49
Page 1 of the Toshiba TLP-ET1U user manual — OWNER’S MANUAL 3LCD PROJECTOR TLP-ET1B TLP-ET1E TLP-ET1U
Page 1 · click to enlarge
Page 1

OWNER’S MANUAL 3LCD PROJECTOR TLP-ET1B TLP-ET1E TLP-ET1U

Page 2 of the Toshiba TLP-ET1U user manual — OWNER’S MANUAL 3LCD PROJECTOR TLP-ET1B TLP-ET1E TLP-ET1U
Page 2 · click to enlarge
Page 2
Toshiba TLP-ET1U — OWNER’S MANUAL 3LCD PROJECTOR TLP-ET1B TLP-ET1E TLP-ET1U diagram (page 2)
Fig. 1

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.

FCC Radio Frequency Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.

authorized by Toshiba, could void the user’s authority to operate the equipment.

Show 4 more labels / short text on this page
USA only · USA only · USA only · CANADA only
Page 3 of the Toshiba TLP-ET1U user manual — 6. Water and Moisture
Page 3 · click to enlarge
Page 3
Toshiba TLP-ET1U — CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS PROVIDED IN diagram (page 3)
Fig. 2

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS PROVIDED IN

THIS OWNER'S MANUAL AND THOSE MARKED ON THE UNIT. KEEP THIS BOOKLET FOR FUTURE REFERENCE.

This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that can be repaired by the user. DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1. Read Owner's Manual After unpacking this product, read the owner's manual carefully, and follow all the operating and other instructions.
4. Ventilation Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been followed.
Toshiba TLP-ET1U — CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS PROVIDED IN diagram (page 3)
Fig. 3
2. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
5. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
3. Source of Light Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes or sight.

6. Water and Moisture

Do not use this product near water. - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and the like.

Page 4 of the Toshiba TLP-ET1U user manual — CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS PROVIDED IN
Page 4 · click to enlarge
Page 4
7. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a soft cloth for cleaning.
11. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
8. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
12. Do not place the product vertically Do not use the product in the upright position to project the pictures at the ceiling, or any other vertical positions. It may fall down.
9. Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
13. Stack Inhibited Do not stack other equipment on this product or do not place this product on the other equipment. Top and bottom plates of this product may develop heat and damage other equipment.
10. Lightning storms For added protection for this product during a storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and power-line surges. When lightning starts, do no touch this product, the connection cable, or the power code plug.
14. Attachments Do not use attachments not recommended by the product manufacturer as they may cause a hazard.

Before Using

Page 5 of the Toshiba TLP-ET1U user manual — S3125A
Page 5 · click to enlarge
Page 5

15. Accessories Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

18. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. (The only part the user should replace is the lamp.)
Toshiba TLP-ET1U — S3125A diagram (page 5)
Fig. 4

S3125A

16. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged. b) If liquid has been spilled, or objects have fallen
20. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

into the product. c) If the product has been exposed to rain or water. d) If the product does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e) If the product has been dropped or damaged in

any way. f) When the product exhibits a distinct change in

21. Do not leave thermal-paper documents or easily damaged items on top of the unit or near the air exhaust for long periods of time. The heat from the unit could erase the information on the thermal paper, or cause damage or warping. Also, when you touch a metal object put near the air exhaust, it could be hot and burn you.

performance.

17. If glass components, including lens and lamp, should break, contact your dealer for repair service. This product incorporates glass components, including a lens and a lamp. If such parts should break, please handle with care to avoid injury and contact your dealer for repair service. The broken pieces of glass may cause to injury. In the unlikely event of the lamp rupturing, thoroughly clean the area around the projector.
Page 6 of the Toshiba TLP-ET1U user manual — TLP-ET1B
Page 6 · click to enlarge
Page 6
22. If smoke is coming out of this product or you could smell something, unplug the power cord plug from the wall outlet. Wait until you can confirm that no more smoke is coming out, and then contact your product dealer. Using this product without taking the action mentioned above may cause a fire or an electric shock.
23. If you wish to install the projector to the ceiling, replace a lamp or clean a filter of the ceiling mounted projector and the like, be sure to ask your product dealer to do so. Doing these things by yourself may cause injury due to a fall, etc.

LABEL LOCATIONS

TLP-ET1B

Toshiba TLP-ET1U — TLP-ET1B diagram (page 6)
Fig. 5

Before Using

Page 7 of the Toshiba TLP-ET1U user manual — EXEMPTION CLAUSES
Page 7 · click to enlarge
Page 7

IMPORTANT PRECAUTIONS

Save Original Packing Materials

The original shipping carton and packing materials will come in handy if you ever have to ship your LCD projector. For maximum protection, repack the set as it was originally packed at the factory.

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location. When the unit is exposed to such a change in temperature, moisture may condense on the crucial internal parts. To prevent the unit from possible damage, do not use the unit for at least 2 hours when there is an extreme or sudden change in temperature.

  • Place and Manner of Installation
  • Do not place the projector in hot locations, such as near heating equipment. Doing so could cause malfunction, and shorten the life of the LCD panel.
  • Avoid locations with oil or cigarette smoke. Doing so will dirty the LCD panel and other optical parts, shortening their lives, and darkening the screen.
  • Do not place slantwise in angle of 20 ° or more. Doing so could shorten the life of the lamp.
  • Using this product near a TV or radio may cause interference to the images or audio sound. If this happens, move it away from the TV or radio.
  • Moving the projector from a low-temperature room to a high-temperature room may cause condensation on the lens or internal parts of the product. If you continue to use it in that situation, the malfunction may result. Ensure to wait until the condensation naturally disappears.
  • In a high altitude location where air is thin, cooling efficiency of the projector is reduced. In this case, lower the ambient temperature and use it.

Avoid Volatile Liquid

Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic products touching the unit for a long time. They will leave marks on the finish. If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.

LCD Panel

  • The life of the LCD panel is limited. Take care over the points below so as to use the panel for years.
  • To prolong the life of this panel, never fail to turn the power off when the panel is not in use and make sure that the lamp has gone out. The state of the lamp being extinguished helps enhance the effect of energy saving.
  • If the air filter is stained and is clogged up, the main unit inner temperature rises. As a result, the life of the LCD is shortened and a malfunction may also occur. Clean the air filter from time to time and replace it regularly. It is recommended that this replacement be done at the time of replacing a lamp. (Ask a dealer where the unit was purchased or your nearby service station about an air filter for replacement.)

In the spaces provided below, record the Model and Serial No. located at the bottom of your LCD projector. Model No. Serial No.

Retain this information for future reference.

EXEMPTION CLAUSES

  • Toshiba Corporation bears no responsibility in the case of damages arising from natural disaster (such as earthquakes, lightning, etc.), fires not liable to Toshiba Corporation, operating by third parties, other accidents, or use under abnormal conditions including erroneous or improper operation and other problems.
  • Toshiba Corporation bears no responsibility for incidental damages (lost profit, work interruption, corruption or loss of the memory contents, etc.) arising from the use of or the inability to use this unit.
  • Toshiba Corporation accepts no liability whatsoever for any damages arising from not having followed the descriptions in this Instruction Manual.
  • Toshiba Corporation accepts no liability whatsoever for any damages arising from malfunctions arising from combination with equipment or software that is not related to Toshiba Corporation.

Before Using

Page 8 of the Toshiba TLP-ET1U user manual — Checking the package contents
Page 8 · click to enlarge
Page 8
Toshiba TLP-ET1U — Copyrights diagram (page 8)
Fig. 6 · Copyrights

Copyrights

Showing or transmitting commercial imaging software or broadcast or cable-broad casting programs with the purpose of other than the personal and private viewing, including modifying images using the freeze or resize functions, or displaying with the varying aspect ratio of the images, could violate the direct or indirect copyrights of the imaging software or broadcast program, etc., if done without first consulting with the copyright holder. For this reason, please take appropriate measures before performing one of the actions listed above, including obtaining a license from the copyright holder.

Disposal

  • This product contains substances which are harmful to humans and the environment.
  • Solder used in the internal parts contains the lead.
  • The lamp contains inorganic mercury. Please dispose of this product or used lamps in accordance with local regulations.
  • Trademarks
  • VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of International Business Machines Corporation.
  • Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.
  • “DCDi” and “TrueLife by Faroudja” are trademarks of Faroudja, a division of Genesis Microchip Corp.

Notational Conventions Used in This Manual

References to pages with related information are annotated as follows. For example, if making a reference to page 36: ( p.36)

Checking the package contents

Please make sure that the following items are included in the box, along with the main unit. If any item is missing, please contact the store immediately where you purchased the product.

I (1) Remote control I (2) R03 (SIZE AAA) batteries for remote control I (3) Owner’s Manual (this document) I (4) Quick Reference I (5) Power cord (see note)

I (6) AV cable

(1) (2) (3) · (4) (5) (6)

Page 9 of the Toshiba TLP-ET1U user manual — Copyrights
Page 9 · click to enlarge
Page 9
Page 9 of the Toshiba TLP-ET1U user manual — Copyrights
Page 10 of the Toshiba TLP-ET1U user manual — (11)
Page 10 · click to enlarge
Page 10
Toshiba TLP-ET1U — (1) diagram (page 10)
Fig. 7

(1)

Toshiba TLP-ET1U — (1) diagram (page 10)
Fig. 8
Toshiba TLP-ET1U — (1) diagram (page 10)
Fig. 9

(6)

(3)

(7)

(5)

(9) (10)

(8)

Toshiba TLP-ET1U — (6) diagram (page 10)
Fig. 10

(11)

(15)

(12)

(14)

(13)

NameFunction
(1) Control panelOperates the projector. ( p.11)
(2) Focusing ringAdjusts the screen focus. ( p.20)

(3) Lens: Projects an expanded video image.

(4) Infrared remote sensorSenses commands from the remote control. ( p.13)

(5) Air exhaust: Expels air that has grown hot inside the unit.

(6) Speaker (Right): Plays the sound input to AUDIO terminal (R).

(7) Connection terminalsConnect external devices. ( p.12, 15, 16)
(8) AC IN socketConnect the supplied power cord here. ( p.17)

(9) Speaker (Left): Plays the sound input to AUDIO terminal (L).

(10) Air intake: Draws in air from outside the unit.

(11) Air filter cover: Remove when cleaning the air filter. ( p.40)

(12) Anti-theft lock hole: Attach a security chain, etc. here.

( 13 ) Tilt standAdjusts the vertical projection angle and the projector's horizontal tilt. ( p.20)

This tilt stand is removable. ( p.39)

(14) Safety lock switch: Prevents the projector's power from being turned on accidentally. ( p.18)

( 15 ) Lamp coverRemove when replacing the lamp.( p.42)
Page 11 of the Toshiba TLP-ET1U user manual — Control panel Remote control
Page 11 · click to enlarge
Page 11

Parts on the control panel and remote control

Control panel Remote control

YP B P R /AV

(2) (3) (5) (6) (7)

NameMain function

(1) ON/STANDBY button: Turns the power on/off (standby). ( p.18, 19) (2) INPUT buttons: Select input. ( p.21) (3) MENU button: Displays menus. ( p.30) (4) Select buttons: Make menu selections and adjustments, etc. ( p.30) In this manual, select buttons are represented by . (5) OK button: Accepts the current selection, e.g., on a menu. ( p.31) (6) EASY button: Displays the easy setting menu. ( p.22) (7) USER button: Calls up a registered user profile. ( p.29) (8) ON indicator: Shows whether the unit is powered on or standby. ( p.17, 18, 45) (9) LAMP indicator: Displays the current lamp mode. ( p.18, 19, 45) (10) TEMP indicator: Lights when internal temperature is too high. ( p.45) (11) FAN indicator: Displays the current cooling fan mode. ( p.18, 19, 45)

( 12 ) LIGHT buttonBy pressing this button, the operation buttons light

up for about 10 seconds. Pressing the button again, while the lights are on, turns off the lights. Pressing another button while the lights are on turns on the lights for another 10 seconds. (13) EXIT button: Turns off the menu screen, etc. ( p.31) (14) PICTURE MODE button: Selects a picture mode. ( p.27) (15) SURROUND button: Selects a surround-sound effect mode. ( p.27) (16) SIZE button: Selects a screen size. ( p.25) (17) MUTE button: Cuts off the sound temporarily. ( p.26) (18) SLEEP button: Cuts off the picture and sound temporarily. ( p.26) (19) D.ZOOM button: Zooms in or out the image. ( p.28) (20) FREEZE button: Pauses the image. ( p.26)

Buttons only on the remote control

* Although the center INPUT button is represented as “YPBPR/AV” in this manual, the button is represented as “YPBPR” on the TLP-ET1U.

Show 18 more labels / short text on this page
Preparations · Remote control transmitter · (12) (1) · (2) · (8) (9) (10) · (11) · (6) · (7) (5) · (4) · (4) · (13) · (3) · (14) (15) (18) · (16) · (17) · (1) · (19) · (20)
Page 12 of the Toshiba TLP-ET1U user manual — (7)
Page 12 · click to enlarge
Page 12
Toshiba TLP-ET1U — (2) diagram (page 12)
Fig. 11

(2)

Toshiba TLP-ET1U — (2) diagram (page 12)
Fig. 12

(7)

(5) (6)

NameFunction

(1) COMPUTER terminal: Inputs RGB signals from a computer or other equipments.

(2) Y, PB/CB, and PR/CR terminals: Input component video signals (Y/PB/PR) from a video device.

(3) SERVICE terminal: Leave this unconnected. Used for repair purposes.

(4) S-VIDEO terminal: Inputs S-Video signals from a video device.

(5) AUDIO terminal: Inputs audio signals from a computer or video device.

(6) VIDEO terminal: Inputs video signals from a video device.

(7) AV IN terminal *Inputs audio and video signals from a video device. The AV IN terminal

cannot receive S-Video signals.

* Although the AV IN terminal is included in illustrations in this manual, the terminal exists only on the TLP-ET1B and TLP-ET1E. TLP-ET1U is not equipped with the AV IN terminal. The AV IN terminal automatically identifies the RGB and composite signals. Check the setting on the connected device as well.

Page 13 of the Toshiba TLP-ET1U user manual — Loading batteries into the remote control
Page 13 · click to enlarge
Page 13

Preparing and using the remote control

Toshiba TLP-ET1U — Preparing and using the remote control diagram (page 13)
Fig. 13 · Preparing and using the remote control

Loading batteries into the remote control

Operating the remote control

Point the remote control toward the projector's infrared remote sensor, and press a button on the remote control.

Remove the battery cover.

  • Operating the projector from the front

Insert dry cell batteries.

Approx. 15°

Check the positive and negative terminals of each battery to load it correctly.

Approx. 5m

  • Operating the projector from the rear

Use two AAA (LR03 or R03) dry cell batteries.

Put back the battery cover.

Approx. 15°

Approx. 5m

G Dry cell batteries

  • Remove the batteries from the remote control when it is not used for an extended period of time.
  • If the remote control stops working or its controlling range decreases, replace all the batteries with new ones.

G The remote control

  • The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting.
  • Do not drop or bang it.
  • Do not leave it in hot or humid locations.
  • Do not get it wet or place it on top of wet objects.
  • Do not take it apart.
  • In rare cases, ambient conditions could impede the operation of the remote control. If this happens, point the remote control at the main unit again, and repeat the operation.

Preparations

Page 14 of the Toshiba TLP-ET1U user manual — Placing the projector
Page 14 · click to enlarge
Page 14

Placing the projector

  • Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
  • If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge. Improper mounting could cause the projector to fall, resulting in an accident.
  • If you wish to mount the projector on the ceiling, remove the tilt stand attached to this unit. Mounting the projector with the tilt stand on the ceiling could cause it to fall, resulting in an accident.
  • If the projector is ceiling-mounted, install the breaker for turning off the power in case of emergency. Let everyone involved with the use of the projector know that fact.

Determine the placement style.

As shown in the figures below, this unit can be placed in four different styles. The factory setting is “Front” and “Standard.” Set “Projection mode 1” and “Projection mode 2” in the “Default setting” menu (see p.35) in accordance with your needs.

Toshiba TLP-ET1U — Placing the projector diagram (page 14)
Fig. 14 · Placing the projector

Determine the projection distance from the lens to the screen to obtain the desired screen size. (The screen sizes listed below are approximate values for a full-size image projected with no keystone adjustment.) The screen size decreases as the lens comes closer to the screen; it increases as the lens goes away from the screen.

As seen from above

Toshiba TLP-ET1U — Placing the projector diagram (page 14)
Fig. 15 · Placing the projector

60 (0.75×1.33) 80 (1.00×1.77) 100 (1.25×2.22) 120 (1.5 ×2.66)

As seen from the side

Projection size (inches) – 0.9317

L (projection distance) =

“L” is the lens-to-screen distance (m) ranging from approximately 0.74 to 3.04 m.

Show 6 more labels / short text on this page
Preparations · Screen · 90° · Lens center · 90° · Reference equation
Page 15 of the Toshiba TLP-ET1U user manual — VCR
Page 15 · click to enlarge
Page 15
Toshiba TLP-ET1U — Connecting a video device diagram (page 15)
Fig. 16 · Connecting a video device
  • Before connection
  • Read the owner’s manual of the device to connect to the projector.
  • Turn off the power of both devices before connecting.
Toshiba TLP-ET1U — Connecting a video device diagram (page 15)
Fig. 17 · Connecting a video device

Connecting a video device

I Using the AV or S-Video cable

Toshiba TLP-ET1U — Connecting a video device diagram (page 15)
Fig. 18 · Connecting a video device
Toshiba TLP-ET1U — Connecting a video device diagram (page 15)
Fig. 19 · Connecting a video device

VCR

I Using the SCART cable

Toshiba TLP-ET1U — VCR diagram (page 15)
Fig. 20

VCR

* The TLP-ET1U cannot use the SCART cable for connection since it has no AV IN terminal.

Page 16 of the Toshiba TLP-ET1U user manual — Connecting a computer
Page 16 · click to enlarge
Page 16

Connecting an input source device (Continued)

Toshiba TLP-ET1U — Connecting an input source device (Continued) diagram (page 16)
Fig. 21 · Connecting an input source device (Continued)

Connecting a DVD player with component video terminals

Toshiba TLP-ET1U — Connecting a DVD player with component video terminals diagram (page 16)
Fig. 22 · Connecting a DVD player with component video termina…

Component video cable (not supplied) Audio cable (not supplied)

Toshiba TLP-ET1U — Connecting a DVD player with component video terminals diagram (page 16)
Fig. 23 · Connecting a DVD player with component video termina…

Connecting a computer

  • Some types of computer cannot be connected to or used with this projector. Check the computer for an RGB output terminal, supported signal, and so on. (See p.47.)
Toshiba TLP-ET1U — Connecting a computer diagram (page 16)
Fig. 24 · Connecting a computer

RGB cable (not supplied)

  • Connect this cable to use the projector’s speaker.

Preparations · DVD player · Computer

Page 17 of the Toshiba TLP-ET1U user manual — TEMP FAN LAMP ON
Page 17 · click to enlarge
Page 17
Toshiba TLP-ET1U — TEMP FAN LAMP ON diagram (page 17)
Fig. 25

Connect the power cord.

q Insert the power cord connector into the AC IN socket on the

projector.

w Insert the power cord plug into a wall or other power outlet.

When the power cord is plugged in, the ON indicator comes on in orange, indicating that the unit is on standby.

TEMP FAN LAMP ON

(Supplied) Power cord connector

Remove the lens cover.

Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat.

  • LCD Panels LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the following precautions:
  • In order to extend the lifetime of the LCD panel, always turn off the power when not in use, and make sure that the lamp is off. Keeping the lamp off is also very effective at saving electricity.
  • If the air filter becomes dirty and clogged, the projector’s internal temperature will rise, shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter from time to time (see p.40), and replace it periodically. Contact the store where you purchased your projector, or your local Service Station for replacement of the air filters. The projector’s LCD panel is made using extremely advanced technology, but there may be black spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please note that these are not malfunctions.

(Orange) · Lit

Page 18 of the Toshiba TLP-ET1U user manual — Safety lock
Page 18 · click to enlarge
Page 18

Turning the power on and off (Continued)

Turning the power on

Press the ON/STANDBY button.

Remote control Control panel

The power is turned on, and three (ON, LAMP, and FAN) indicators come on in green. After a moment, the startup screen appears.

TEMP FAN LAMP ON

  • Do not look into the lens during operation. Doing so could damage your vision.
  • Families with children should be particularly careful.
  • Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
  • Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns or deform, discolor, or break the object.
  • Notes
  • The startup screen will disappear after a moment. You can dismiss the startup screen before this by performing any operation.
  • After the startup screen disappears, the language menu is displayed when you use the projector for the first time after purchase. (See p.20.)
  • Turning the power on starts the cooling fan running with operating sound .
Toshiba TLP-ET1U — TEMP FAN LAMP ON diagram (page 18)
Fig. 26

Safety lock

You can prevent the projector’s power from being turned on accidentally. Set the safety lock switch on the bottom of the main unit to ON.

In standby mode with the safety lock switch set to ON, the ON indicator lights in orange and in green alternately. Once you have set the safety lock switch to ON, you have to hold down the ON/ STANDBY button for at least two seconds to turn on the power of the projector. Other operations are the same.

Show 5 more labels / short text on this page
Lit (Green) · (Green) · (Green) · Lit · Lit
Page 19 of the Toshiba TLP-ET1U user manual — PRECAUTIONS
Page 19 · click to enlarge
Page 19

Turning the power off

Press the ON/STANDBY button.

Remote control Control panel

A message appears on the screen, confirming that you wish to shut off the power. This message will disappear after a moment. (This operation is no longer valid after the message disappears.)

Press the ON/STANDBY button again.

Remote control Control panel

The screen is turned off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode.

During cooling, the LAMP indicator flashes. In this state, the power cannot be turned back on. In addition, unplugging the power cord in this state will shorten the life of the lamp.

FAN TEMP LAMP ON

The LAMP and FAN indicators go off, and the projector goes into standby mode.

FAN TEMP LAMP ON

PRECAUTIONS

  • Before unplugging the power cord, make sure that the LAMP indicator is off. Unplugging the power cord to cut off the power while the projector is running or being cooled will shorten the life of the lamp. However, please unplug the power cord if the projector locks up or acts abnormally.
  • If the power cord was unplugged before cooling was completed, give the lamp sufficient time to cool down before plugging it back in. If the lamp overheats, it may fail to light, and its lifetime will be shortened.
  • Before turning the power off, turn down the volume if possible.
Show 6 more labels / short text on this page
Cooling in progress · (Orange) (Green) · (Green) · Flashing · Cooling completed · (Orange) (Off) (Off)
Page 20 of the Toshiba TLP-ET1U user manual — Projecting
Page 20 · click to enlarge
Page 20

Projecting

Turn on the power.

Turn on the power by following the instructions in “Turning the power on” (see p.18).

Adjust the projection angle.

Adjust the angle of the main unit as you like. • The angle can be adjusted within a range of approximately ±10° in a horizontal position.

Adjust the screen focus.

Adjust the focus using the focusing ring.

Select the language (when using the unit for the first time).

When the projector is used for the first time after purchase, the menu for selecting the language for on-screen messages and menu items is displayed in English.

English French German Italian Spanish Portuguese Japanese

Remote control Control panel

q Use the and buttons to select the desired language.

Remote control Control panel

w Press the OK button to accept the

language setting. The message for setup confirmation is displayed in a selected language.

  • The language can also be set via the “Language” option in the “Default setting” menu (see p.35).
  • This owner’s manual assumes that English has been selected.

English Français · Deutsch Italiano Español · Português

Page 21 of the Toshiba TLP-ET1U user manual — YP B P R /AV
Page 21 · click to enlarge
Page 21

Place the connected device in operating status.

Turn on the connected device such as a video device.

YP B P R /AV

Select the connected input.

(Using the remote control) Press an INPUT button (VIDEO/S, YPBPR/ AV, or COMPUTER) to select the input. The picture from the selected input will be projected.

YP B P R /AV

  • Pressing the VIDEO/S button switches the projected picture between the VIDEO and S-VIDEO inputs.
  • Pressing the YP B P R /AV button switches the projected picture between the Y/P B /P R and AV inputs. (This function is available only for the TLPET1B and TLP-ET1E.)

(Using the control panel) Press the INPUT button on the main unit to select the input. Pressing the INPUT button switches the inputs as shown below.

Video → S-video→ Y/PB/PR → AV → Computer

  • “AV” is available only for the TLP-ET1B and TLP-ET1E.

Adjust the volume with the ( ) and ( ) buttons.

Remote control Control panel

The speaker volume can be adjusted when an audio signal is being input.

  • Notes
  • Note that because of the lamp characteristics, the brightness of the lamp may fluctuate slightly.
  • A lamp is a consumable supply. If the lamp is used for an extended period, images will appear dark, and the lamp could burn out. This is characteristic of a lamp, and is not a malfunction.
  • Although this projector supports a wide range of RGB signals (see p.48), any resolution signals that exceed the number of pixels of the LCD panel of this projector will enlarge or compress the pictures, causing lack of some information or affecting image quality.
  • With some models of computer having LCD displays or the like, displaying images simultaneously on the projector and the monitor’s display may cause the images to be shown improperly. If this happens, turn off the computer’s LCD display. For information on how to turn off the LCD display, see the owner’s manual of your computer.
  • If a signal not supported by the projector is input, the icon will appear.
  • If a no signal is being input from the connected device, the icon will appear. The screen color will also change to blue and the TOSHIBA logo will appear.
  • If no signal is being input for more than 10 minutes, the power will be automatically turned off and the unit will be placed in the standby state.
  • If an unavailable operation button is pressed, the icon will appear.
  • The audio input to the Audio terminals is played regardless of the input source. (When the AV input is selected, however, AV IN audio is played.)
Page 22 of the Toshiba TLP-ET1U user manual — Projecting
Page 22 · click to enlarge
Page 22
Toshiba TLP-ET1U — Projecting diagram (page 22)
Fig. 27 · Projecting

You can use the EASY button to configure frequently used adjustments and settings. For any settings (adjustments) other than the settings (adjustments) described in this section, see “Using the menus” ( p.30) to make the settings (adjustments) as required.

Toshiba TLP-ET1U — Projecting diagram (page 22)
Fig. 28 · Projecting

Use the and buttons to select the menu item you want to set or adjust.

The selected item can now be set or adjusted.

Use the and buttons to set or adjust the selected item.

Set or adjust the selected item by referring to the table on p.23. Some items need to be set with and buttons after pressing OK button.

Repeat steps 2 and 3 above to complete settings or adjustments, then press the EASY button.

The menu disappears. •You can also dismiss the menu by pressing the EXIT button on the remote control.

Page 23 of the Toshiba TLP-ET1U user manual — Projecting
Page 23 · click to enlarge
Page 23

Projection size Change the picture area size on the screen.

Use to decrease the projection size or to increase it. See p.24 for details.

Keystone Correct the keystone (trapezoid) distortion of the screen. (For keystone distortion, see “Correction of keystone distortion” described below.)

Use to shrink the lower part or to shrink the upper part.

Picture mode Switch to the picture mode suitable for movie or game screens. Press OK button first, and then set the item with and buttons. Standard/Cinema/Game

Screen size Switch the screen size. Press OK button first, and then set the item with and buttons. Full/Theater wide/4:3/Zoom See p.25 for details.

Up/down shift Scroll the screen up or down, for example, when subtitles are outside the picture area. (Adjustable only when the screen size is “Zoom”.)

Lamp power Lower lamp power to decrease the cooling fan noise.

Standard/Low Setting lamp power “Low” makes the screen a little darker but makes the cooling fan noise quieter.

Projection mode 1 Select whether the placement style is front or rear projection.

  • Notes
  • “Projection size” can also be adjusted by using ( ) and ( ) buttons, on the remote control or main unit. (See p.24.)
  • Decreasing the projection size may affect image quality slightly. (It does not change the menu size.)
  • “Picture mode” can also be set via the PICTURE MODE button on the remote control or the “Picture adjustment” menu. (See p.27, 32.)
  • “Screen size” can also be set via the SIZE button on the remote control or the “Default setting” menu. (See p.25, 35.)
  • “Keystone”, “Up/down shift”, “Lamp power”, and “Projection mode 1” can also be adjusted via the “Default setting” menu. (See p.35.)
  • The items set and adjusted on the “Easy setting” menu are saved when the power is turned off with the ON/ STANDBY button. They are not saved if power is disconnected by unplugging the power cord or by a power failure.

G Correction of keystone distortion

When the tilt stand (see p.20) is used to change the projection angle, the picture will undergo keystone (trapezoid) distortion. The projector is capable of correcting this keystone distortion.

Before correction After correction

  • Depending on the amount of keystone adjustment and the content of images, some information may be lost or the picture quality may suffer. Keystone adjustment will not change the shape of the menus.

Item Description · Down Up · Front/Rear

Page 24 of the Toshiba TLP-ET1U user manual — Projecting
Page 24 · click to enlarge
Page 24
Toshiba TLP-ET1U — Projecting diagram (page 24)
Fig. 29 · Projecting

You can change the projection size (picture area size on the screen).

Toshiba TLP-ET1U — Projecting diagram (page 24)
Fig. 30 · Projecting

The adjustment bar is displayed. Pressing the ( ) button decreases the projection size.

The adjustment bar is displayed. Pressing the ( ) button increases the projection size. You cannot make the image larger than its original size.

  • Notes
  • The “Projection size” can also be adjusted via the “Easy setting” menu. (See p.22.)
  • Decreasing the projection size may degrade the images more or less.
Page 25 of the Toshiba TLP-ET1U user manual — Projecting
Page 25 · click to enlarge
Page 25
Toshiba TLP-ET1U — Projecting diagram (page 25)
Fig. 31 · Projecting

The projection screen of this projector is 16:9, though the screen size can be changed depending on the input signal.

Press the SIZE button on the remote control.

Pressing the SIZE button for the first time displays the current screen size. Pressing the SIZE button while the current screen size is displayed cycles the screen size through the following options:

Full → Theater wide → 4:3 → Zoom

Full : This mode is best for squeeze-signal video images. Theater wide: This mode is best for 4:3-signal video images on the wide screen. 4:3 : This mode is best for 4:3-signal video images on the 4:3-

size screen. Zoom : This mode is best for video images of letter-box or cinema signals.

Input signal Projection screen

4:3 signal Full Theater wide (O)

4:3 signal Zoom

Squeeze signal Full (O) Theater wide

4:3 signal Zoom

  • Notes
  • The screen size cannot be changed when the 16:9 signal is input.
  • You cannot select “Theater wide” and “Zoom” when the input is COMPUTER.
  • An adjustment bar of “Up/ down shift” is displayed in “Zoom” mode and you can make the adjustment (See

Letter box signal Full Theater wide

4:3 Zoom (O)

p. 23, 35.) • If you use this function on commercial video soft- ware or on a broadcast or cable broadcast except for the purpose of your private viewing and listening, it may infringe the copyright protected by the copyright laws. (O): Optimum screen size

Cinema signal Full Theater wide

4:3 Zoom (O)

Show 12 more labels / short text on this page
→ · ↑ ↓ · ← · → · ↑ ↓ · ← · → · ↑ ↓ · ← · → · ↑ ↓ · ←
Page 26 of the Toshiba TLP-ET1U user manual — Pausing the picture (Freeze)
Page 26 · click to enlarge
Page 26

Cutting off the sound/Pausing the picture

Cutting off the sound temporarily (Mute)

You can turn off the projector’s sound temporarily.

Press the MUTE button on the remote control.

The sound are cut off. Pressing the MUTE button again cancels the Mute function and releases the sound.

  • Notes
  • The icon will appear while Mute is in effect.
  • Operating any other function cancels the muting.
  • It can also be canceled by pressing the EXIT button on the remote control.
Toshiba TLP-ET1U — Cutting off the sound temporarily (Mute) diagram (page 26)
Fig. 32 · Cutting off the sound temporarily (Mute)

Cutting off both the picture and sound temporarily (Sleep)

You can turn off both the projector’s picture and sound temporarily.

Press the SLEEP button on the remote control.

The picture and sound are cut off. Pressing the SLEEP button again cancels the Sleep function and releases the picture and sound.

  • Notes
  • The icon will appear while Sleep is in effect.
  • Operating any other function cancels the sleeping.
  • It can also be canceled by pressing the EXIT button on the remote control.
Toshiba TLP-ET1U — Cutting off both the picture and sound temporarily (Sleep) diagram (page 26)
Fig. 33 · Cutting off both the picture and sound temporarily (…

Pausing the picture (Freeze)

You can pause the picture being projected.

Press the FREEZE button on the remote control.

The picture pauses. Pressing the FREEZE button again cancels the Freeze function.

  • Notes
  • The icon will appear while Freeze is in effect.
  • The Zoom function can be used on a frozen image to enlarge it. The freeze is canceled by performing any other operation or by pressing the EXIT button on the remote control.
  • Even if an image is frozen on the projector, the pictures are running on the video or other device. Audio continues to be output as well.
  • If you use this function on commercial video software or on a broadcast or cable broadcast except for the purpose of your private viewing and listening, it may infringe the copyright protected by the copyright laws.
Page 27 of the Toshiba TLP-ET1U user manual — Switching to surround sound
Page 27 · click to enlarge
Page 27
Toshiba TLP-ET1U — Switching to surround sound diagram (page 27)
Fig. 34 · Switching to surround sound

You can switch the picture mode suitable for the movie or game screen.

Press a PICTURE MODE button (STD./CINEMA/ GAME) on the remote control.

The projector will switch to the selected picture mode.

STD. : Standard picture mode CINEMA : Suitable for watching movies GAME : Suitable for game screens

  • Select the desired picture mode.
Toshiba TLP-ET1U — Switching to surround sound diagram (page 27)
Fig. 35 · Switching to surround sound

Switching to surround sound

Surround sound reproduces deep and expanded atmospheres through natural, realistic sensations.

Press the SURROUND button on the remote control.

Pressing the SURROUND button for the first time displays the current surround mode. Pressing the SURROUND button while the current surround mode is displayed cycles the sound through the following options:

: Surround (Off)

: Surround (Soft)

: Surround (Hard)

: Turns a mono signal into quasi-stereo.

  • Notes
  • Surround sound can also be set via the “Audio adjustment” menu (see p.34).
  • Surround sound effect depends on each input source.
  • Selecting with a stereo source may lose its true-stereo sensation.

→ → →

Page 28 of the Toshiba TLP-ET1U user manual — Switching to surround sound
Page 28 · click to enlarge
Page 28
Toshiba TLP-ET1U — Switching to surround sound diagram (page 28)
Fig. 36 · Switching to surround sound

You can enlarge (zoom in) the image being projected.

Toshiba TLP-ET1U — Switching to surround sound diagram (page 28)
Fig. 37 · Switching to surround sound

To decrease the zoom magnification, press the D.ZOOM button on the remote control.

Pressing the D.ZOOM button decreases the zoom magnification. (The image cannot be shrunk to less than its original size.)

Use the , , , and buttons to move the enlarged area.

  • Notes
  • The icon will appear while Zoom is in effect.
  • An enlarged image can be frozen using the FREEZE button. The Zoom function on the frozen image can also be used.
  • Since the enlargement is performed by digital processing, enlarging will cause the image to appear jagged.
  • Rarely, the picture could become garbled while the enlarged area is being moved.
  • Operations other than Freeze will cancel the zooming.
  • It can also be canceled by pressing the EXIT button on the remote control.
  • If you use this function on commercial video software or on a broadcast or cable broadcast except for the purpose of your private viewing and listening, it may infringe the copyright protected by the copyright laws.
Page 29 of the Toshiba TLP-ET1U user manual — Calling up a user profile
Page 29 · click to enlarge
Page 29

Calling up a user profile

You can easily switch the projector to the settings saved on the “User memory” menu (see p.37).

Press the USER button.

Remote control Control panel

The “User memory call” menu will appear.

Pressing the USER button again will dismiss the “User memory call” menu. Pressing the EXIT button on the remote control will also dismiss the “User memory call” menu.

Use the and buttons to select the settings saved (as a user profile) in user memory, then press the OK button.

Remote control Control panel

The projector is switched to the selected user memory settings. Selecting “A/V reset” resets only the items in the “Picture adjustment” and “Audio adjustment” menus to their default settings.

User memory call · A/V reset · Call

Page 30 of the Toshiba TLP-ET1U user manual — Calling up a user profile
Page 30 · click to enlarge
Page 30
Toshiba TLP-ET1U — Calling up a user profile diagram (page 30)
Fig. 38 · Calling up a user profile

You can call up on-screen menus, and conduct a number of adjustments and settings using the operation buttons on the remote control and on the main unit’s control panel. For details on each adjustment and setting item, see the corresponding page. Menus shown below are only for operation instructions and might be different from the actual display.

Status display ( p. 36)

User memory ( p. 37)

( p. 32)

( p. 34)

( p. 35)

Toshiba TLP-ET1U — Calling up a user profile diagram (page 30)
Fig. 39 · Calling up a user profile

Use the and buttons to select a desired menu icon, then press the button.

and indicate you can change the adjustment and setting item.

Picture adjustment · Audio adjustment · Default setting

Page 31 of the Toshiba TLP-ET1U user manual — Calling up a user profile
Page 31 · click to enlarge
Page 31
Toshiba TLP-ET1U — Calling up a user profile diagram (page 31)
Fig. 40 · Calling up a user profile

Use the and buttons to select a desired adjustment or setting item.

Press the OK button if an adjustment bar or selection items did not displayed on the Step 3. A selection list will appear.

Toshiba TLP-ET1U — Calling up a user profile diagram (page 31)
Fig. 41 · Calling up a user profile

Use the and buttons to adjust the selected item.

and indicate you can select options for the current item.

Press the OK button if an adjustment bar or selection items did not displayed on the Step 3.

A confirmation dialog box will appear, asking you whether to execute the item.

Use the and buttons to set the selected item.

To execute the item, select “Yes” using the and buttons, then press the OK button.

and indicate you can select options for the current item.

  • Notes
  • Pressing the MENU button with a menu screen displayed returns you to the previous menu screen.
  • Pressing the EXIT button on the remote control dismisses the menu screen.
  • The items adjusted and set with these menus are saved when the power is turned off with the ON/STANDBY button. They are not saved (except the user memory and lamp time settings) if power is disconnected by unplugging the power cord or by a power failure.
Page 32 of the Toshiba TLP-ET1U user manual — Picture adjustment menu
Page 32 · click to enlarge
Page 32

Using the menus (Continued)

Picture adjustment menu

Use this menu to adjust image-related items.

e.g.

Toshiba TLP-ET1U — Picture adjustment menu diagram (page 32)
Fig. 42 · Picture adjustment menu

Use the and buttons to select the picture adjustment menu icon [ ], then press the button.

Use the and buttons to select an item you want to adjust, then adjust it according to the table shown below.

Item Description Video S-video Y/PB/PR AV Computer

TrueLife by Enhance uneven edges, for example, of Faroudja skins without highlighting outlines. Yes – Lower Higher

Lower Higher Yes Yes Yes*1 Yes –

Picture mode Switch the picture mode using and . Standard/Cinema/Game Yes –

Reddish Greenish Yes*2 Yes*2 – Yes –

R-gain Adjust the base level of red in pictures.

G-gain Adjust the base level of green in pictures.

B-gain Adjust the base level of blue in pictures.

*1 “Noise reduction” can be adjusted only when the signal formats are 480i and 576i. *2 “Tint” can be adjusted only when the video modes are NTSC and NTSC4.43.

Page 33 of the Toshiba TLP-ET1U user manual — Picture adjustment menu
Page 33 · click to enlarge
Page 33

Item Description Video S-video Y/PB/PR AV Computer

Auto setting Adjust items, such as the sampling phase, depending on the type of input signal. – Yes Press the OK button.

Phase Adjust with and to minimize flicker. – – Yes – Yes

Frequency Adjust with and to minimize periodic patterns and flickering when many vertical – Yes lines appear on the screen.

H-position Adjust the horizontal position of the picture screen. – Yes Move left Move right

V-position Adjust the vertical position of the picture screen.

Move up Move down – Yes

Clamp 1) Press the OK button. 2) Use or to select Clamp 1 or 2. Clamp 1: Adjust the position of the clamp pulse.

Down Up – Yes Clamp 2: Adjust the width of the clamp pulse.

Signal format Set the Y/PB/PR signal DTV format. 1) Press the OK button. 2) Select one from the displayed list with and , then press the OK button. Auto: Automatically identifies the type of input signal. If this fails, select one from the following: – – Yes – –

480i(525i)@60/480p(525p)@60/ 576i(625i)@50/576p(625p)@50/ 720p(750p)@60/720p(750p)@50/ 1080i(1125i)@60/1152i(1250i)@50/ 1035i(1125i)@60/1080i(1125i)@50

Video mode Set the VIDEO and S-VIDEO color system. 1) Press the OK button. 2) Select one from the displayed list with and , then press the OK button. Auto: Yes Yes – Yes –

Automatically identifies the type of input signal. If this fails, select one from the following: NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43

  • Notes
  • Items can be adjusted/set (marked with “Yes”) or cannot (marked with “–”) depending on each type of input.
  • Pressing the EXIT button on the remote control dismisses the menu screen.

Shorter Longer

Page 34 of the Toshiba TLP-ET1U user manual — Audio adjustment menu
Page 34 · click to enlarge
Page 34

Using the menus (Continued)

Toshiba TLP-ET1U — Audio adjustment menu diagram (page 34)
Fig. 43 · Audio adjustment menu

Audio adjustment menu

Use this menu to adjust audio-related items.

e.g.

Toshiba TLP-ET1U — Audio adjustment menu diagram (page 34)
Fig. 44 · Audio adjustment menu
Toshiba TLP-ET1U — Audio adjustment menu diagram (page 34)
Fig. 45 · Audio adjustment menu

Use the and buttons to select the audio adjustment menu icon [ ], then press the button.

Use the and buttons to select an item you want to adjust, then adjust it according to the table shown below.

Remote control Control panel

Toshiba TLP-ET1U — Audio adjustment menu diagram (page 34)
Fig. 46 · Audio adjustment menu

Treble Adjust the higher frequency range of audio output.

Bass Adjust the lower frequency range of audio output.

Balance Adjust the balance in volume level between the left and right speakers.

Surround Select a surround sound effect mode with and .

  • Notes
  • Pressing the EXIT button on the remote control dismisses the menu screen.
  • On rare occasions, turning up the volume or bass may cause the projected screen to flutter, depending on the input audio signal level. If this is the case, turn it down.
Page 35 of the Toshiba TLP-ET1U user manual — US
Page 35 · click to enlarge
Page 35

Default setting menu

Use this menu to make settings such as the placement style (projection mode).

e.g.

Press the MENU button.

Use the and buttons to select the default setting menu icon [ ], then press the button.

Use the and buttons to select an item you want to set, then set it according to the table shown below.

Remote control Control panel

US

Item Description Keystone Correct the keystone (trapezoid) distortion of the screen.

Shrinking lower part Shrinking upper part Screen size Set the screen size mode. 1) Press the OK button. 2) Select one from the displayed list with and , then press the OK button. Full/Theater wide/4:3/Zoom (“Theater wide” and “Zoom” cannot be selected when the input is COMPUTER.) This item can also be set with the SIZE button on the remote control. (See p.25.) Up/down shift Scroll the screen up or down, for example, when subtitles are outside the picture area. (Adjustable only when the screen size is “Zoom”.)

Down Up Lamp power Select lamp power with and . Standard/Low Projection mode 1 Select projection mode 1 with and , according to the projector’s placement style. Front/Rear Projection mode 2 Select projection mode 2 with and , according to the projector’s placement style. Standard (floor-mounted)/Ceiling Language Select the language for on-screen menus and messages. 1) Press the OK button. 2) Select one from the displayed list with and , then press the OK button. English/Français/Deutsch/Italiano/Español/Português/ NTSC mode Set with and . US : NTSC (US) mode JAPAN: NTSC (JAPAN) mode All reset Reset all of the adjustment and setting items to the defaults. 1) Press the OK button. 2) In the dialog box displayed, use or to select whether to execute this function, then press the OK button. Lamp time reset Reset the lamp timer. (See p.44)

Show 17 more labels / short text on this page
Menu Exit Enter · Default setting · Keystone · Screen size · Zoom · Up/down shift · Lamp power · Low · Projection mode 1 · Front · Projection mode 2 · Standard · Language · English · NTSC mode · All reset · Lamp time reset
Page 36 of the Toshiba TLP-ET1U user manual — Status display menu
Page 36 · click to enlarge
Page 36

Using the menus (Continued)

Status display menu

This menu displays information about the input signal, lamp use time, etc.

e.g.

Press the MENU button.

Toshiba TLP-ET1U — Status display menu diagram (page 36)
Fig. 47 · Status display menu

Use the and buttons to select the Status display menu icon [ ].

The “Status display” menu will appear.

Remote control Control panel

Item Description Video S-video Y/PB/PR AV Computer

Input Displays the input source name. Yes

Mode name Displays the RGB signal mode name.*1 – Yes

H-resolution Displays the horizontal resolution (in dots). – Yes

V-resolution Displays the vertical resolution (in dots). – Yes

H-frequency Displays the horizontal sync frequency. – Yes

V-frequency Displays the vertical sync frequency.*2 – Yes

Sync Displays the sync signal polarity.*3 – Yes

Signal format Displays the Y/PB/PR signal format. – – Yes – –

Video mode Displays the video signal color system. Yes Yes – Yes –

Lamp time Displays the total time of lamp use.*4 Yes

Version Displays the firmware version.*5 Yes

*1 : The mode of supported RGB signals ( p.48) is shown. *2 : Same as the refresh rate of the computer signal. *3 : Sync signal polarity shown as P (positive) or N (negative) for “H/V”. *4 : Display “Lamp time” as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) *5 : “Version” shows the version of the projector’s internal control program. This version is referred for customer service, etc.

  • Notes
  • Items can be displayed (marked with “Yes”) or cannot (marked with “–”) depending on each type of input.
  • Pressing the EXIT button on the remote control dismisses the menu screen.
Page 37 of the Toshiba TLP-ET1U user manual — User memory menu
Page 37 · click to enlarge
Page 37

User memory menu

Use this menu to register up to three sets of adjustments and settings made on the menu screen as user profiles. You can call any of the user profiles later using the USER button. (See p.29.)

Toshiba TLP-ET1U — User memory menu diagram (page 37)
Fig. 48 · User memory menu
Toshiba TLP-ET1U — User memory menu diagram (page 37)
Fig. 49 · User memory menu

Use the or button to select the user memory menu icon [ ].

Use the or button to select the user memory number with which you want to register the current settings, then press the OK button.

Press the OK button, use the , , , or button to select a desired icon, then press the OK button.

The cursor will move to the user memory registration icon.

Page 38 of the Toshiba TLP-ET1U user manual — LIVING
Page 38 · click to enlarge
Page 38

Using the menus (Continued)

Press the button, move the cursor to the user memory registration name, then press the OK button.

Remote control Control panel

The user memory name input screen will appear.

Use the , , , and buttons to select each character you want to enter, then press the OK button.

Remote control Control panel

Press the OK button after selecting each character. To clear all the input characters, select “ CA ” and press the OK button.

When you finish entering characters, use the , , , and buttons to select “ OK ”, then press the OK button.

Remote control Control panel

The cursor will be moved to the user memory registration name.

Use the button to select “Registration”, then press the OK button.

Remote control Control panel

The current settings are registered in the selected user memory number. To return to the screen of Step 3, select “Cancel” and press the OK button.

LIVING

USER MEMORY2

USER MEMORY3

  • Notes
  • To change a registered icon or user memory name, re-register it from the beginning.
  • Pressing the EXIT button on the remote control will dismiss the menu screen.
Show 10 more labels / short text on this page
User memory · Registration Cancel · User memory · Registration Cancel · User memory · Registration Cancel · Menu · User memory · User1 · Setting
Page 39 of the Toshiba TLP-ET1U user manual — PRECAUTIONS
Page 39 · click to enlarge
Page 39
Toshiba TLP-ET1U — LIVING diagram (page 39)
Fig. 50

Do not remove the tilt stand unless when you replace the lamp or mount the projector on a ceiling. Removing the tilt stand leaves the projector unstable and may block the air intake at the bottom. Usually, the projector must be used with the tilt stand.

PRECAUTIONS

  • Before removing the tilt stand, be sure to turn off the power and unplug the power cord.

Place the unit upside down.

Turn the projector over and place it carefully. It is recommended to lay a soft cloth, such as a thick towel, under the unit to prevent it from shaking or getting scratched.

Loosen the three screws.

Position the tilt stand where you can see three screws in the centers of their respective screw holes. Loosen the screws by turning them counterclockwise several times.

Detach the tilt stand.

Hold the tilt stand with both hands, turn it counterclockwise, then lift it to remove.

To put the tilt stand back in place, take the above steps in reverse order. At this time, always make sure that the three screws have been tightened.

Page 40 of the Toshiba TLP-ET1U user manual — LIVING
Page 40 · click to enlarge
Page 40
Toshiba TLP-ET1U — LIVING diagram (page 40)
Fig. 51

The air filter prevents dust and debris from getting inside the projector. Never run the projector with the filter removed. The air filter should be cleaned regularly.

  • The

icon message, “Check the air filter for dirt,” is displayed every 100 hours. (If the usage time exceeds 100 hours, this message is displayed for 30 seconds when the image is displayed for the first time after the power is turned on. The message will be dismissed with any operation.) • Check out the filter and, if any debris is found, use the following procedure for cleaning.

Toshiba TLP-ET1U — LIVING diagram (page 40)
Fig. 52
  • Request cleaning and maintenance of a ceiling-mounted unit to your projector dealership.

Pull out the air filter by taking the catch shown in the figure with your fingertips. After turning the projector over, place it carefully. It is recommended to lay a soft cloth, such as a thick towel, under the unit to prevent it from shaking or getting scratched.

Carefully remove the dust and dirt from the air filter with a vacuum cleaner or the like.

  • Notes
  • Allowing dirt and dust to build up in the air filter will worsen the air circulation inside the projector, causing the internal temperature to rise, the projector to stop working or malfunction.
  • Insert the air filter all the way in. Leaving gaps will allow dust and dirt to get inside the projector again.
  • If the air filter is torn, consult with your dealer about replacing it with a new one. Continuing to use a ripped filter will allow dust and dirt to get inside the projector.
Page 41 of the Toshiba TLP-ET1U user manual — Replacing air intake and exhaust fans, and air filter
Page 41 · click to enlarge
Page 41
Toshiba TLP-ET1U — Lens cleaning diagram (page 41)
Fig. 53 · Lens cleaning
  • Request cleaning and maintenance of a ceiling-mounted unit to your projector dealership.

Lens cleaning

  • Clean the lens with a commercially available blower and/or lens cleaner.
  • The lens is easily scratched, so do not rub it with hard objects, or strike it.
Toshiba TLP-ET1U — Lens cleaning diagram (page 41)
Fig. 54 · Lens cleaning
  • Clean the main unit after unplugging the power cord.
  • Wipe dirt off the main unit gently with a soft cloth.
  • If the soiling is severe, dip the cloth in a neutral detergent diluted in water, wring well, and gently wipe off the dirt, then finish up by wiping with a dry cloth.

Replacing air intake and exhaust fans, and air filter

To maintain the performance, it is recommended that these should be replaced about every two or three years. Consult with your dealer for details.

Page 42 of the Toshiba TLP-ET1U user manual — Lens cleaning
Page 42 · click to enlarge
Page 42
Toshiba TLP-ET1U — Lens cleaning diagram (page 42)
Fig. 55 · Lens cleaning

A lamp is a consumable supply. If the lamp is used for an extended period, images will appear dark, and the lamp could burn out. This is a characteristic of a lamp, and is not a malfunction. (The lifetime of the lamp depends on conditions of use.) If this happens, replace it with a new one.

Toshiba TLP-ET1U — Lens cleaning diagram (page 42)
Fig. 56 · Lens cleaning
  • If the projector is mounted on a ceiling, request lamp replacement to your projector dealership.
  • When replacing, always use dedicated lamp “TLPLET1” (sold separately).
Toshiba TLP-ET1U — Lens cleaning diagram (page 42)
Fig. 57 · Lens cleaning
  • If you have been using the projector, the lamp will be very hot, and may cause burn injuries. Wait for the lamp to cool (for longer than one hour) before replacing it.
  • If the lamp should break, please handle with care to avoid injury due to broken pieces (see p.8) and contact your dealer for repair service.
  • Notes
  • “Lamp time” in the “Status display” menu indicates the time of lamp use (as a rough guide).
  • When “Standard” is set for the lamp power mode in the “Default setting” menu, replace the lamp after 2,000 hours of use as a guide. Using the unit with the “Low” lamp power mode extends the lifetime of the lamp.
  • The lamp may stop lighting before the Lamp time reaches the hours as a guide or before a replacement message appears.

G Lamp replacement messages

  • This unit displays lamp replacement messages at appropriate timings depending on the total time of lamp usage in the “Standard” or “Low” lamp power mode.
  • The message, “Lamp life is approaching the end. Replace the lamp in earlier time,” starts appearing whenever you turn on the power from 100 hours before the replacement deadline. The message will be dismissed either after 30 seconds or with any operation.
  • Once the lamp has reached the replacement deadline, the message, “Lamp life has ended. Replace the lamp immediately,” appears whenever you turn on the power. The message will be dismissed with any operation. The power is turned off automatically about seven minutes after the message appears (the LAMP indicator remains on in orange during that period).
Toshiba TLP-ET1U — Lens cleaning diagram (page 42)
Fig. 58 · Lens cleaning

Wait for at least one hour.

Remove the tilt stand.

Follow the instructions in “Removing the tilt stand” (see p.39) to remove the tilt stand.

Page 43 of the Toshiba TLP-ET1U user manual — Lens cleaning
Page 43 · click to enlarge
Page 43
Toshiba TLP-ET1U — Lens cleaning diagram (page 43)
Fig. 59 · Lens cleaning

Loosen the screw, put your fingers on the hollow, then pull up to the direction of the arrow as shown in the figure to remove the lamp cover.

Toshiba TLP-ET1U — Lens cleaning diagram (page 43)
Fig. 60 · Lens cleaning

Loosen the two lamp locking screws, and pull up the handle to remove the lamp.

Align the orientation, press down the new lamp until it reaches to the bottom, and lock it in place using the two lamp locking screws.

Align the lamp cover, and press it in, then tighten the screws loosened in Step 4 until the lamp cover is no longer loose.

Put back the tilt stand using the reverse procedure to remove it. (Continued)

Page 44 of the Toshiba TLP-ET1U user manual — PRECAUTIONS
Page 44 · click to enlarge
Page 44

Reset the lamp timer.

q Turn on the power of this unit.

The startup screen appears, followed by the replacement message screen.

w Press the MENU button.

The menu screen appears.

e Select “Lamp time reset” in the “Default setting” menu and press the OK button.

r Select “Yes” on the dialog screen, then press the OK button.

The lamp time is reset.

PRECAUTIONS

  • Take Step 9 above within seven minutes after turning on the power.
  • Be sure to reset the lamp time after replacing the lamp.
  • The lamp may burst if you continue to use it without replacing while resetting the lamp time.
  • Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the lamp will not come on (see p.45).
  • Always replace the lamp with a new one.
  • The lamp is made out of glass. Do not touch the glass surface with your bare hands, bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)

This projector’s lamps contain trace amounts of environmentally harmful inorganic mercury. Be careful not to break used lamps, and dispose it in accordance with local regulations.

Maintenance · Lamp replacement (Continued) · G Used lamps

Page 45 of the Toshiba TLP-ET1U user manual — PRECAUTIONS
Page 45 · click to enlarge
Page 45

Trouble indications

The indicator lights inform you of internal abnormalities.

ON LAMP TEMP FAN

No power

⇒Problem with projector

  • Unplug the power cord, and contact your dealer.

ON LAMP TEMP FAN

Lamp went out during use

⇒Lamp temperature is high so that it is difficult to turn on, the lifetime of the lamp

(Red lit) (Red lit) (Green lit)

  • has ended, or the projector is malfunctioning.
  • Unplug the power cord and wait for a short while, then turn the power back on.
  • If a lamp burns out, replace it with a new one. ❈ After approx. one minute of abnormal display, the projector returns to the

standby state waiting for internal cool down.

ON LAMP TEMP FAN

Power went out during use, or won’t come on

⇒Internal overheating, or the outside temperature is too high.

(Red lit) (Red lit or flashing)

  • Replace the projector so that the air intake and exhaust are not blocked.
  • Unplug the power cord and wait for a short while, then turn the power back on.
  • Clean the air filter. (See p.40.) ❈ The

(Orange lit or flashing)

icon will appear before the power goes out. ❈After approx. two minutes of error display, the projector returns to the standby

state waiting for internal cool down.

ON LAMP TEMP FAN

Power went out during use, or won’t come on

⇒Problem with internal cooling fan.

(Red lit) (Red lit or flashing)

  • Unplug the power cord, and contact your dealer. ❈ The

icon will appear before the power goes out. ❈After approx. one minute of abnormal display, the projector returns to the

(Orange lit or flashing)

standby state waiting for internal cool down.

(Green lit or flashing)

Power went out during use

ON LAMP TEMP FAN

⇒The lamp cover is not properly attached.

  • Unplug the power cord, and reattach the lamp cover. (See p.42.) ❈ After approx. one minute of abnormal display, the projector returns to the

standby state waiting for internal cool down.

PRECAUTIONS

  • Make sure to unplug the power cord if something goes wrong.
  • If the power cord is unplugged before cooling is complete, give the lamp enough time to cool before plugging it back in. If the lamp overheats, it may fail to light. Unplugging the power cord repeatedly when the temperature is high will shorten the life of the lamp. (Even if you are not concerned about lamp lifetime, the light may not come on if you do not wait for at least three minutes.)
Show 11 more labels / short text on this page
Others · (Off) · (Green lit) · or · or · (Green lit) · or · or · (Red lit) (Orange · (Green lit) · flashing)
Page 46 of the Toshiba TLP-ET1U user manual — Before calling service personnel
Page 46 · click to enlarge
Page 46

Before calling service personnel

If you think something is wrong, check the followings before contacting customer service. Please see “Trouble indications” ( p.45) as well.

If This Happens Check

  • No power
  • Is the safety lock on? (See p.18)
  • Is the power cord plugged in? Is it connected to the projector?
  • Is the lamp cover loose? (See p.44)
  • Is the lamp correctly mounted? (See p.42)
  • Power goes out during use
  • Is the ambient temperature high? (See p.45.)
  • Is the air filter clogged? (See p.45.)
  • Is the air intake or air exhaust blocked? (See p.45.)
  • Was the lamp timer reset after the lamp was replaced? (See p.44)
  • Was no signal being input for 10 minutes? (See p.21)
  • No picture
  • Is a wrong input selected? (See p.21.)
  • Is the Sleep function on? (See p.26.)
  • Is the brightness setting minimized? (See p.32.)
  • Are the connections set up correctly? (See p.15, 16.)
  • Are all the connected devices functioning properly?
  • No audio
  • Is the mute function on? (See p.26.)
  • Is the volume setting minimized? (See p.21.)
  • Are the connections set up correctly? (See p.15, 16.)
  • Are all the connected devices functioning properly?
  • Picture not displayed correctly
  • Is the input signal supported by the projector? (See p.48, 49.)
  • Is the correct video mode selected? (See p.33.)
  • Is the correct signal format selected? (See p.33.)
  • Are there any problems with the signal source such as the video tape?
  • Picture blurred
  • Is the lens dirty? (See p.41.) Part of picture out of focus
  • Is the lens focus adjusted optimally? (See p.20.)
  • Is the projection distance within the projector's supported range? (See p.14.)
  • Is the projector or its screen placement angle tilted too far? (See p.14.)
  • Is the sharpness or sampling phase misadjusted? (See p.32, 33.)
  • Image is dark
  • Is the brightness or contrast misadjusted? (See p.32.)
  • Is the lamp approaching the end of its service life? (See p.36.)
  • Colors too light
  • Are the color, tint, R-gain, G-gain, or B-gain misadjusted? (See p.32.) Bad shading
  • Is the screen dirty?
  • Is the lamp approaching the end of its service life? (See p.36.)
  • Remote control doesn’t work
  • Are the remote control's batteries drained?
  • Are the batteries inserted into the remote control correctly? (See p.13.)
  • Is the remote control being used within the effective range? (See p.13.)
  • Are there any obstructions between the remote control and projector?
  • Are there any fluorescent or other bright lights shining at the projector’s infrared remote sensor?

Others

Page 47 of the Toshiba TLP-ET1U user manual — List of general specifications
Page 47 · click to enlarge
Page 47

Specifications

List of general specifications

Power consumption 220 W (At standby: 1 W (AC 100 - 120 V) or 3 W (AC 220 - 240 V))

Weight 3.5 Kg

External dimensions 320 × 85 × 320 (W × H × D) (Tilt stand excluded) (including protrusions) 320 × 131 × 320 (W × H × D) (Tilt stand included)

Cabinet materials* PC+ABS resin and ABS resin

Operating environmental conditions Temperature: 0 to 35°C; Relative humidity: 30 to 70%

LCD panel Display method Three-panel transmission

Panel size 0.5 type

Drive system TFT active matrix

Number of pixels 409,920 (854 H × 480 V)

Lens F = 2.3

Lamp High-pressure mercury lamp

Projection screen size 32 - 120 type

Projection distance 0.74 - 3.04 m

Speaker 5 W + 5W (Stereo)

COMPUTER terminal Mini D-sub 15-pin

Y terminal RCA pin pack

PB/CB terminal RCA pin pack

PR/CR terminal RCA pin pack

S-VIDEO terminal Mini DIN 4-pin

VIDEO terminal RCA Pin jack, 1V (p-p), 75Ω

AUDIO (L/R) terminals RCA Pin jack × 2, 1.5 V (rms); 22 kΩ or more

SERVICE terminal Mini DIN 8 pin

AV IN terminal Scart socket (21 pin)

* Major parts of this product display the names of their materials in order to facilitate recycling after it becomes no longer usable.

Others · Item Specification · Connection terminals

Page 48 of the Toshiba TLP-ET1U user manual — SXGA3_60 SXGA3_75 SXGA3_85
Page 48 · click to enlarge
Page 48

List of supported signals

I List of supported signals (RGB signals)

This projector supports the following RGB signals. However, the screen may show flicker or streaking depending on the computer model. Please adjust the projector if this happens. (Either execute “Auto setting” in the “Picture adjustment” menu or manually adjust picture-related items such as “Phase”. (See p.32.))

Clock (MHz) 35.500 25.175 31.500 31.500 36.000 36.000 40.000 50.000 49.500 56.250 57.283 44.900 65.000 75.000 78.750 94.500 79.857 108.000 108.000 148.500 108.000 135.000 157.500 118.094 162.000 175.500 189.000 202.500 229.500 204.750 218.250 234.000

(Hz) 85.039 59.940 72.809 75.000 85.008 56.250 60.317 72.188 75.000 85.061 74.550 86.957 60.004 70.069 75.029 84.997 74.700 75.000 60.000 85.002 60.020 75.025 85.024 60.012 60.000 65.000 70.000 75.000 85.000 60.000 60.000 60.000

(kHz) 37.927 31.469 37.861 37.500 43.269 35.156 37.879 48.077 46.875 53.674 49.725 35.522 48.363 56.476 60.023 68.667 60.134 67.500 60.000 85.938 63.981 79.976 91.146 63.973 75.000 81.250 87.500 93.750 106.250 83.640 86.333 90.000

720 x 400 640 x 480

720x400_85 VGA_60 VGA_72 VGA_75 VGA_85 SVGA_56 SVGA_60 SVGA_72 SVGA_75 SVGA_85

832 x 624 1024 x 768

XGA_60 XGA_70 XGA_75 XGA_85

MAC19" SXGA1_75 QuadVGA_60 QuadVGA_85

1152 x 864 1280 x 960

SXGA3_60 SXGA3_75 SXGA3_85

1400 x 1050 1600 x 1200

SXGA+ UXGA_60 UXGA_65 UXGA_70 UXGA_75 UXGA_85 1792x1344_60 1856x1392_60 1920x1440_60

1792 x 1344 1856 x 1392 1920 x 1440

Show 9 more labels / short text on this page
Others · Specifications (Continued) · Refresh rate · H-frequency · Resolution · Mode · 800 x 600 · MAC16" XGA_43i · 1280 x 1024
Page 49 of the Toshiba TLP-ET1U user manual — Separately sold product
Page 49 · click to enlarge
Page 49

I List of supported signals (Y/P B /P R signals)

Signal format fh(kHz) fv(Hz) 480i(525i)@60Hz 15.73 59.94 480p(525p)@60Hz 31.47 59.94 576i(625i)@50Hz 15.63 50.00 576p(625p)@50Hz 31.25 50.00 720p(750p)@60Hz 45.00 60.00 720p(750p)@50Hz 37.50 50.00 1080i(1125i)@60Hz 33.75 60.00 1080i(1125i)@50Hz 28.13 50.00 1035i(1125i)@60Hz 33.75 60.00 1152i(1250i)@50Hz 31.25 50.00

I List of supported signals (Video and S-Video signals)

Video mode fh(kHz) fv(Hz) fsc(MHz) NTSC 15.73 60 3.58 PAL 15.63 50 4.43 SECAM 15.63 50 4.25 or 4.41 PAL-M 15.73 60 3.58 PAL-N 15.63 50 3.58 PAL-60 15.73 60 4.43 NTSC4.43 15.73 60 4.43

Toshiba TLP-ET1U — I List of supported signals (Y/P B /P R signals) diagram (page 49)
Fig. 61 · I List of supported signals (Y/P B /P R signals)

Pin assignment of COMPUTER terminal

Pin No.

Pin description Video signal (R) Video signal (G) Video signal (B) GND GND GND(R) GND(G) GND(B)

Pin No.

Pin description N.C GND GND N.C

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15

10 15 6 11 Mini D-sub 15-pin connector

Vertical sync signal N.C

Input signal • RGB input R/G/B signals: 0.7 V (p-p), 75Ω Horizontal sync signal: TTL level (Positive/negative polarity) Vertical sync signal: TTL level (Positive/negative polarity)

Toshiba TLP-ET1U — Pin assignment of COMPUTER terminal diagram (page 49)
Fig. 62 · Pin assignment of COMPUTER terminal

Separately sold product

Replacement lamp Model TLPLET1

Horizontal sync signal

Page 50 of the Toshiba TLP-ET1U user manual — I List of supported signals (Y/P B /P R signals)
Page 50 · click to enlarge
Page 50
Page 50 of the Toshiba TLP-ET1U user manual — I List of supported signals (Y/P B /P R signals)

Ask about the Toshiba TLP-ET1U

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Toshiba TLP-ET1U

Be the first to ask — other owners or our team will answer.

Original document

Toshiba TLP-ET1U manual PDF

50 pages·4.4 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…