
Before using the iron, read the use instructions completely. Keep the use instructions during the entire life of the appliance.
1 Preconditioning nozzles 2 Spray nozzle 3 Water tank opening 4 Precision shot button 5 Spray button 6 Steam regulator 7 Temperature selector 8 Temperature pilot light 9 «auto-off» light 10 Heel rest 11 Textile Protector 12 Soft Textile Protector
This iron is designed for tap water. If you have extremely hard water, we recom- mend that you use a mixture of 50 % tap water and 50 % distilled water. Fill the water tank to «max» marking. Never use distilled water exclusively. Do not add any additives (e.g. starch). Do not use condensation water from a tumble dryer. • Before fi lling with water, turn off the steam regulator (6) («0» = steam off).
5712710094_TS_780-755_S06-84.indd 9 5712710094_TS_780-755_S06-84.indd 9 18.11.13 08:38 18.11.13 08:38

To turn on the iron again, just move it. When the «auto-off» pilot light stops fl ashing, the electrical power is on again. The automatic shut-off will be activated approximately 2 minutes after the iron is plugged into a socket.
Soft Textile Protector (12) (STPl) The Soft Textile Protector ensures an increased heat protection and utmost care for most delicate fabrics thanks to its specially designed SoftTouch cushion. Even most delicate, ironable* fabrics are protected against heat damage and shiny patches are avoided. With the Soft Textile Protector attached, you can iron all ironable fabrics without an intermediate cloth. The Soft Textile Protector is perfectly suited for touching up e.g. creases of delicate business suits without having to use an ironing cloth.
Spray function Press the spray button (5).
Dry ironing Set the steam regulator (6) on position «0» (= steam off).
(* in order to know whether a piece of garment is ironable, please refer to its care label.)
Automatic shut-off The «auto-off» mechanism causes a slight rattling noise during ironing. This is normal and in no case indicates a fault of the iron. The red «auto-off» light (9) will fl ash when the automatic shut-off is activated. This happens when the iron has rested: – horizontally on its sole plate for about 30 seconds or – vertically on its heel rest for about 8 minutes.
Unplug the iron and turn the steam regulator to position «0». To prolong the life of the iron, empty the water tank. Store the cool iron in a dry place always standing on its heel rest.
5712710094_TS_780-755_S06-84.indd 10 5712710094_TS_780-755_S06-84.indd 10 18.11.13 08:38 18.11.13 08:38

Trouble-shooting guide
To clean the sole plate, use steel wool. Never use a scouring pad, vinegar or other chemicals. To clean the soft material on the handle, use soapy water.
The anticalc valve located on the lower end of the steam regulator has to be decalcifi ed regularly (e.g. whenever steam development is insuffi cient). For this, the water tank has to be empty.
Removing the steam regulator with the anticalc valve Turn the steam regulator clockwise towards the steam setting «6». Keep on turning fi rmly beyond the resistance until the steam regulator is lifted. When positioned at x, pull it out vertically. Do not touch the anticalc valve at its lower end. Immerse the anticalc valve in vinegar (not vinegar essence) or lemon juice for a minimum of 30 minutes. Brush off remaining residues and rinse under running water (fi g. H, 1-7).
Subject to change without notice.
Please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at a Braun Service Centre or at appropriate collection points provided in your country.
Re-inserting the steam regulator When re-inserting the steam regulator, make sure the steam regulator base still points on setting x (fi g. H, 8). Firmly push down the steam regulator until it turns back to setting «6» (fi g. H) where it catches. Notice: The iron must never be used without steam regulator.
In order to clean the steam chamber from residues, decalcify it as shown in picture section I, 1-8. Caution: Hot water and steam will come out from the sole plate when the steam regulator is turned clockwise beyond setting «6». Wait for the sole plate to cool down, then clean it as described above. Then refi ll the tank with water, heat up the iron and press the precision shot button 4 times to rinse the iron before ironing (fi g. I, 9-13). Do not use commercial decalcifi ers, they may damage the iron.
5712710094_TS_780-755_S06-84.indd 11 5712710094_TS_780-755_S06-84.indd 11 18.11.13 08:38 18.11.13 08:38
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Drops coming out of the steam vents. | Turn the steam regulator anti-clock- wise to reduce the steam or turn it off. Take longer intervals when pressing the precision shot button. Select a higher temperature setting. | p.3 | |
| Less steam develops or no steam at all. | Check water level. Clean the anticalc valve. | p.3 | |
| Calcium particles coming through the steam vents. | Decalcify the steam chamber. | p.3 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.