EN
Official user manual

Emstim AST-300C - Electrical Muscle Stimulation

20 pages·819 KB·Miscellaneous·PDF·ENDEFRITNLJA
Emstim AST-300C - Electrical Muscle Stimulation
Table of Contents 1 sections Guaranteed card ShowHide
Page 1 of the Emstim AST-300C - Electrical Muscle Stimulation user manual
Page 1 · click to enlarge
Page 1
Emstim AST-300C - Electrical Muscle Stimulation diagram (page 1)
Fig. 1

Shenzhen OSTO Technology Company Limited

No 43,Long feng Road, Xinsheng Community

Longgang Street, Longgang District, 518116 Shenzhen

City, Guangdong, China

Page 2 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — You have nothing more to lose,
Page 2 · click to enlarge
Page 2

A British blood circulation device electronic

Emstim AST-300C - Electrical Muscle Stimulation — A British blood circulation device electronic diagram (page 2)
Fig. 2 · A British blood circulation device electronic
Emstim AST-300C - Electrical Muscle Stimulation — A British blood circulation device electronic diagram (page 2)
Fig. 3 · A British blood circulation device electronic

Muscle stimulator

Electric Stimulator E.M.S Scientifically proven instruction manual

Emstim AST-300C - Electrical Muscle Stimulation — Muscle stimulator diagram (page 2)
Fig. 4 · Muscle stimulator

You have nothing more to lose,

than only their pain

Emstim AST-300C - Electrical Muscle Stimulation — You have nothing more to lose, diagram (page 2)
Fig. 5 · You have nothing more to lose,
Page 3 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Content
Page 3 · click to enlarge
Page 3

Thank you for purchasing the electronic muscle stimulator. Before using the device, please read the user manual. Above all, read the precautions carefully so that you can operate the device correctly. Please keep this instruction manual.

Content

Identification of Parts 1

Functions 2

Use of electrode gel pads 2

Operation 3

Storage/maintenance 7

Specifications 7

Error correction 8

Description of Modes 9

Diagram of the reflex zones of feet 12

Guaranteed card

Page 4 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Identification of parts
Page 4 · click to enlarge
Page 4

Identification of parts

1. Electrode silicon surface for feet 2. Instructions for use 3. Foot sole massage roller 4. Adaptor 5 LCD screen 6. Handle 7. electrode pads 8 . Remote control 9. Electrode cables
Emstim AST-300C - Electrical Muscle Stimulation — Identification of parts diagram (page 4)
Fig. 6 · Identification of parts
Page 5 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Use of electrode gel pads
Page 5 · click to enlarge
Page 5

Function and intended use of the equipment

The principle of our electronic muscle stimulator is that the low frequency current stimulates pain points in the human body and causes muscular contractions or relaxation. When muscle relaxation occurs, a large amount of blood can enter. When muscle restriction occurs, blood containing metabolites is sent out. These types of measures will recycle, which can help speed up circulation and ease pain, swelling, fatigue, and other symptoms.

The expected purpose of our electronic muscle stimulator is to relieve or reduce human muscular pain, swelling, fatigue pain and promote blood circulation.

1. Appropriate to better ABS materials and designs, in accordance with human construction. The device looks very modern and fine. 2. 99 types of electromagnetic wave intensity with a stepless setting will meet the required ideal result in the correct order. 3. 25 minutes automatic time setting 4. There are 25 types of massage modes for the soul and body. Each impulse massage mode improves the various symptoms and eliminates fatigue. 5. All functions can be operated by remote control and are easy to use.

Use of electrode gel pads

1. The size of the pads is 5.5 x 8.5 cm. 2. Connect the output cable to the electrode gel pads. 3. Then connect the output cable to the electric muscle stimulator. 4. Remove the protective film from gel pads. 5. Attach the electrode gel pads evenly to the skin. 6. Hold the power button for 3 seconds to turn on the device and set stimulation mode and output intensity as you wish (the display shows your chosen mode and level). 7. Keep the pads clean and never expose them to sunlight. 8. If the electrode gel pads are not sufficiently sticky or dirty, clean the pad or take new ones. Do not clean the electrode gel pads with chemicals. 9. After repeated use, the pads must be replaced. Please take new pads if the current pad has not been used within one year.

Page 6 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — This is how you proceed with the remote control:
Page 6 · click to enlarge
Page 6

Operation

Emstim AST-300C - Electrical Muscle Stimulation — Operation diagram (page 6)
Fig. 7 · Operation

Before you start using the device, check that it is in its original state: MODE intensity level, SOLE intensity level and time display show zero, MODE display 1. Other values may affect the functioning of the device and lead to inaccurate results.

1. Put your feet on the device. 2. Press the power button for about 3 seconds to turn on the device. The LCD display will light up blue. 3. Then you can adjust the mode by pressing “” and ““ to select different modes. The maximum mode is 25. 4. The intensity can be increased by pressing the buttons “” ” or decreased by pressing of the keys ““ ” . 5. You can set the modes at any time, but once you reset the mode, the intensity is reset to "0". To avoid a user shock from the new mode, the user should reset intensity. 6. To finish the massage, the user can turn off the device by pressing on power button for about 3 seconds.

ON/OFFPress the button for about 3 seconds to turn the device on or off

: Increase the initial intensity of the sole

Select a mode from 25 pre-modified massage modes upward

: Increase the initial intensity of electrodes

: Reduce the initial intensity of the sole

Select a mode from 25 preset massage modes downward

: Reduce the initial intensity of electrodes

This is how you proceed with the remote control:

1. Open the battery cover on the back of the remote. 2. Insert the two AAA batteries (7#) into the battery cassette with correct polarity. 3. Close the battery cover.
Page 7 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Warnings:
Page 7 · click to enlarge
Page 7

Comments:

1. Please note that it is a recognized accessory, removable parts and materials approved by default. 2. It is not necessary to check and replace the original power source regularly. 3. Normally, this device is affected by high frequency electromagnetism and microwave irradiation machine. Please stay away from these devices at a distance of more than 500 mm when using them.

Caution:

It is used mainly in adults and requires energy and intelligence. The following patients can only use this device after consultation with the doctors, otherwise there may be accidents or physical complaints:

1. Patients with extreme impairment and critical disease. 2. Patients with tumor, cancer, hyperthyroidism, tuberculosis-active period, purulent inflammation. 3. Patients with heart disease and at some age. 4. Patients who are nervous have fear of electronic muscle stimulators. 5. Patients suffering from severe diabetes, high fever, skin allergies, traumatic hemorrhage and fractures. 6. Patients with high blood pressure. 7. Patients with abnormal skin diseases. 8. Patients suffering from psychopathy. 9. Patients who are currently undergoing treatment or feel body abnormalities. 10. If the product performance changes as follows: The output level becomes weaker, strong, even no output, the display is not correct, etc. To end the use of the machine and send it back to the manufacturer or professional maintenance office. 11. The Medical Electrical Equipment requires special precautions regarding EMC and must be installed and put into service in accordance with the EMC information contained in attached documents (see page 13-16). 12 Portable and mobile RF communication devices can affect the medical equipment. 13. The use of accessories, converters and cables other than those specified except the converters or cables sold by the manufacturer of the equipment or system as spare parts for internal components may result in increased EMISSION or reduced IMMUNITY of the apparatus or system.

Warnings:

1. It is forbidden to use the patient with an implanted electronic device (e.g. B. a pacemaker) without medical advice. 2. Please note that the stimulator can have an impact on surgical procedures in patients. Follow the doctor’s advice. 3. Do not operate the device in close proximity (e.g. B. 1 m) to short wave or microwave therapy devices, as this can lead to instabilities in the stimulator output. 4. Please note that the following people should follow the doctor’s advice if they want to use the device: pregnant women and those who suffer from tumor, chronic disease, serious illnesses, severe heart disease or mental disorder. 5. Please do not leave the electrodes with metal substances such as bracelet, watch, necklace etc. come into contact. 6. Make sure your skin is clean before using the electrodes.

Page 8 of the Emstim AST-300C - Electrical Muscle Stimulation user manual
Page 8 · click to enlarge
Page 8
7. Do not use the device in wet conditions, such as in the bathroom. 8. Please do not sit or stand on it and throw or drop anything onto the device. 9. Please do not use it immediately if you feel discomfort and nausea while using. 10. Do not put electrodes near the thorax, as this can increase your risk of heart fibrillation.

Explanation of images, symbols, warnings and abbreviations on the device.

1(symbol for ‘BATCH CODE’). This symbol should be marked with the production number B and next diagram, batch code and LOT number and batch number etc. Example: ABC123 2(symbol for ‘DATE OF PRODUCTION’). This symbol should be next to the number.) Date of manufacture of medical device (the symbol is before the date of manufacture). 3SYMBOL FOR “ATTENTION, LOOK UP IN OUR INSTRUCTIONS OF USE” 4After acceptance of the CE certification, the CE mark is shown as follows. The vertical height shall not be less than 5 mm, clearly visible, clear and indelible. CEConformity assessment procedures shall be carried out by a notified body. The registration number of the notified body should be the side of the CE mark (usually at bottom right). The diameter of the CE marking should not be smaller than the 5 mm semi-circle of both composite parts. The XXXX in the lower right corner is the identification number of the notified body, for example ITS-0473. All medical products sold on the EU market must have the "CE" mark. The CE mark means that: A. the device meets the essential requirements of MDD; the device can be legally sold on the market within the EU. C. the apparatus has passed conformity assessment procedures. There are two types of CE markings affixed to medical devices. That is, the CE mark without a notified body identification number and the CE label with the notified body's identification number.
Page 9 of the Emstim AST-300C - Electrical Muscle Stimulation user manual
Page 9 · click to enlarge
Page 9
5The symbol for the manufacturer (the "Manufacturer" tag), the tag should contain the company name and address of the producer. Product manufacturers, EC represent the name and address of importer and/or distributor. 6Symbol for 'People's Representative in the European Community. The symbol for the authorised representative in the European Community (‘EU authorised representative’) shall include on the label the name and address of the undertaking approved by the European Union. 7Waste products should be handled legally. 8BF equipment 9Up 10Fragile 11Keep dry 12Stacks 13Serial number of the apparatus
Page 10 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Specification
Page 10 · click to enlarge
Page 10

Storage/maintenance

1. Wipe the device with a damp cloth or neutral cleaning agent. Do not use explosive liquids such as thinner or gasoline to clean the device. 2. Keep it away from the magnetic field and range of children. 3. Keep the device away from moisture, high temperatures, direct sunlight or splash water. 4. If the electrode pads are not sufficiently adhered or dirty, wipe them with damp cloth or exchange them for new ones. Do not clean the electrode pads with chemicals. 5. The machine must not be rebuilt or repaired on its own, otherwise we the manufacturer will not consider the warranty. 6. If you are not using it for a long time, please remove the batteries from the remote control.

Environmental protection

After use, please make a waste classification and divide the components into electrode pads, cardboard boxes and so on.

Specification

Model number: AST-300C The apparatus belongs to type BF class II as defined in Section 5.

Emstim AST-300C - Electrical Muscle Stimulation — Specification diagram (page 10)
Fig. 8 · Specification

Rated voltage: 5V DC, 1000 mA power supply by adapter: WT0502400 Rated Voltage: 100-240V nominal input: 0,1A output waveform: square-wave frequency pulse repetition frequencies: 10-100 HZ Maximum amplitude of the output voltage: 72V Software version No: MC0188F-REV-V1.0

Rated frequency50-60Hz nominal power: 5V 100mA pulse duration: 115 Effect of load impedance: 1K
Condition of the operation10 – 40 °C 30% RH ~ 75%RH 860 hPa to 1060 hpa
Storage and transport status10 - 40 860 hPa to 1060 hpa
Page 11 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Error correction
Page 11 · click to enlarge
Page 11

Beware of electrode gel pads (cleaning)

Never glue two adhesive pads to each other. Keep the adhesive pads clean and never expose them to high temperatures and direct sunlight.

To protect the gel pads, always place them on the gel-pad protection after use. Do not touch the gel of pads, as it reduces the gel and its function. Do not clean the electrodes with hot water or chemicals.

If the electrode pads are dirty, it may lack adhesive strength and skin can become irritated. If this is the case, pads should be moistened with water and the dirty part wiped. This enables a pad restoration of the adhesive poser. However, if there is too much water it loses its adhesive strength. The best way is to buy another pad.

The electrode contact points have passed the biocompatibility test (test report is SDFY-2006-2623). The test report shows that the device does not cause skin irritation.

Error correction

QuestionsReasonSolution No stimulationIs the cable connected? Has the protective membrane been removed from the pads?Connect the cable properly. Remove the protective membrane from the pads. Weak stimulationDo the pads stick firmly to your skin? Do the pads overlap? Are the pads dirty? Is the intensity weak? Is the place where they stick not good?Give the pads tightly. Untighten the pads and glue it again. Clean the pads. Set the intensity more strongly. Change the place where the pads stick. The skin becomes red and curledIs the therapy time too long? Are the pads too dry? Are the pads sticking too tightly? Are the pads dirty? Are the pads damaged?The therapy time is always 10-15 minutes. Clean with the wet cloth and use it again. Give the pads firmly to your skin. Clean the pads. Change the pads. Power supply was interrupted during therapyDo the pads fall off of your skin? Is the cable damaged? No battery? Is the therapy time over?Turn off the power supply and glue on the pads again. Turn off the power and reconnect pads. Change the battery. The power supply is switched off after 15 minutes.
Page 12 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Description of the modes
Page 12 · click to enlarge
Page 12

Description of the modes

Emstim AST-300C - Electrical Muscle Stimulation — Description of the modes diagram (page 12)
Fig. 9 · Description of the modes
MODEMODEL 1Acupuncture boost 2Acupuncture 3Acupuncture kneading 4Acupuncture knocking 5Scrapping 6Presses 7Massage 8Massage boost 9Pressure pressing 10Acupuncture presses 11Acupuncture hammers 12Kneading 13Knocking 14Scrapping pressures 15Cupping 16Body shape 17Hammers 18Massage knocking 19Pushing 20Rolling stamping 21Presses 22Scam 23Acupuncture therapy massage 24Shiatsu 25Rolling kneading
Page 13 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Example of the Use of Electrode Pads
Page 13 · click to enlarge
Page 13

Example of the Use of Electrode Pads

Emstim AST-300C - Electrical Muscle Stimulation — Example of the Use of Electrode Pads diagram (page 13)
Fig. 10 · Example of the Use of Electrode Pads

shoulder, back muscle pain etc.

Emstim AST-300C - Electrical Muscle Stimulation — Example of the Use of Electrode Pads diagram (page 13)
Fig. 11 · Example of the Use of Electrode Pads
Emstim AST-300C - Electrical Muscle Stimulation — Example of the Use of Electrode Pads diagram (page 13)
Fig. 12 · Example of the Use of Electrode Pads

waist muscle pain, etc.

Emstim AST-300C - Electrical Muscle Stimulation — Example of the Use of Electrode Pads diagram (page 13)
Fig. 13 · Example of the Use of Electrode Pads
Show 4 more labels / short text on this page
Shoulder, back · symptom · waist · syndrome
Page 14 of the Emstim AST-300C - Electrical Muscle Stimulation user manual
Page 14 · click to enlarge
Page 14
Emstim AST-300C - Electrical Muscle Stimulation diagram (page 14)
Fig. 14

Arm numbness, muscle pain etc.

Emstim AST-300C - Electrical Muscle Stimulation diagram (page 14)
Fig. 15
Emstim AST-300C - Electrical Muscle Stimulation diagram (page 14)
Fig. 16

Leg muscle pain, etc.

Emstim AST-300C - Electrical Muscle Stimulation diagram (page 14)
Fig. 17
Show 4 more labels / short text on this page
Arm · Symptom · Leg · Symptom
Page 15 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Diagram of the reflex zones of feet e
Page 15 · click to enlarge
Page 15

Diagram of the reflex zones of feet e

Emstim AST-300C - Electrical Muscle Stimulation — Diagram of the reflex zones of feet e diagram (page 15)
Fig. 18 · Diagram of the reflex zones of feet e

Cerebellar - Brain-series

Show 31 more labels / short text on this page
Forehead cavity forehead circumcision · brain · nose · pituitary · trigeminal · neck · hypertension point · esophagus · adrenal · thyroid · adjunct - heart · abdomen · spleen · Celiac plexus · pancreas · gallbladder · duodenum · kidney · descending colon · ascending colon · urate · ileoceccal valve · bladder · sigma, rectum · blind appendix · anus · insomnia · gonade (sex gland) · sciatic nerve
Page 16 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Emissions Fulfilment level Electromagnetic environment - Guidance
Page 16 · click to enlarge
Page 16

Attached documents:

Instructions for use

1. AST-300C requires special precautions regarding EMC and must be installed and put into service in accordance with the EMC information contained in accompanying documents. 2. Portable and mobile RF communication devices can affect the ST-300C.
1. It is warned that the use of accessories, converters and cables other than those used by AST-300C manufacturer as spare parts for internal components may result in increased EMISSIONS or reduce safety of AST -300C. 2. It is warned that the AST-300C must not be used or stacked alongside other devices. 3.

Guidance and manufacturer’s declaration – electromagnetic

Immunity

The AST-300C is intended for use in the electromagnetic environment specified below. The customer or user of the AST-300C must ensure that it is used in such an environment.

Emissions Fulfilment level Electromagnetic environment - Guidance

The AST-300C uses RF energy only for its internal function. Therefore, RF emissions are very low and it is unlikely that neighboring electronic devices will be disturbed.

HF emissions CISPR 11 Group 1

HF emissions CISPR 11 Class B

The AST-300C is suitable for use in all facilities, including residential buildings and those directly connected to the low voltage public grid that supplies buildings used for residential purposes.

Voltage fluctuations/flicker emissions IEC 61000-3-3

Show 4 more labels / short text on this page
Technical description · Harmonic emissions IEC 61000-3-2 · Class A · Corresponds
Page 17 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — IEC 61000-4-8
Page 17 · click to enlarge
Page 17

Guidance and manufacturer's declaration - electromagnetic

Immunity

The AST-300C is intended for use in the electromagnetic environment specified below. The customer or user of the AST-300C must ensure that it is used in such an environment.

Immunity test IEC 60601

Test level Fulfilment degree Electromagnetic environment - instructions

Floors should be made of wood, concrete or ceramic tiles. If the floor is covered with synthetic material, relative humidity should be at least 30%. Fast electrical transition to IEC 61000-4-4

Electrostatic discharge (ESD) IEC 61000-4-2

± 6 kV Contact to ± 8 kV air

± 6 kV Contact to ± 8 kV air

± 2 kV for power lines

The quality of the network should correspond to that of a typical business or hospital environment.

± 2 kV for power lines

±1 kV line(s) and neutral conductor

The quality of the network should correspond to that of a typical business or hospital environment.

±1 kV line(s) and neutral conductor

± 2 kV line(s) to earth 95% decrease in UT for 0.5 cycles 40% UT (60% dip in ut) for 5 cycles 70% UT (30% decrease in the UT) for 25 cycles 95% decrease in UT for 5s

± 2 kV line(s) to earth 95% decrease in UT for 0.5 cycles 40% UT (60% dip in ut) for 5 cycles 70% UT (30% decrease in the UT) for 25 cycles 95% decrease in UT for 5s

The quality of the network should correspond to that of a typical business or hospital environment.

Voltage dips, short interruptions and voltage fluctuations of the power supply input lines IEC 61000-4-11

If a dip or interruption of the mains voltage occurs, the current of the AST-300C can drop from normal level. You may need to use an uninterruptible power supply or battery.

If image distortions occur, it may be necessary to position the AST-300C image intensifier further away from sources of magnetic fields with mains frequency or to install a magnetic shield. The magnetic field of the mains frequency should be measured at the intended installation location to ensure that it is sufficiently low. NOTE UT is the AC current of the mains voltage before application of test level.

3 A/m 3 A

IEC 61000-4-8

Overvoltage IEC 61000-4-5 · mains frequency (50/60Hz) · magnetic field

Page 18 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Immunity test IEC 60601
Page 18 · click to enlarge
Page 18

Guidance and manufacturer's declaration - electromagnetic

Immunity

The AST-300C is intended for use in the electromagnetic environment specified below. The customer or user of the AST-300C must ensure that it is used in such an environment.

Immunity test IEC 60601

Compliance

Electromagnetic environment -

Test level

Degree

Guidance

3 Vrms 150 kHz to 80 MHz

Portable and mobile RF communication devices should not be used closer to any part of the AST-300C, including cables than the recommended distance calculated from the equation applicable to transmitter frequency. Recommended distance

d=f,2 80 MHz to 800 MHz

Radiated HF 3 V/m 3 V /m d=2.3 80 MHz to 2.5 GMHz IEC 61000-4-3 80 MHzto 2.5 GHz where P is the maximum output power of the transmitter in watts (W) according to the manufacturer of the sender and d is the recommended distance in meters (m).

The field strengths of fixed RF transmitters, as determined by an electromagnetic location survey should be below the matching level in each frequency range.

In the vicinity of devices, interference may occur with the following symbol marked:

Telephones) and land radio, amateur radio, AM and FM radio broadcasting and television broadcasting, cannot theoretically be accurately predicted. In order to assess the electromagnetic environment based on fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength at the location where AST-300C is used exceeds the allowed RF conformity value, then the AST - 300C should be monitored for normal operation verification. If unusual performance characteristics are observed, additional measures may be required e.g. B. a realignment or other location of the AST-300C. b. In the frequency range from 150 kHz to 80 MHz, field strengths should be below 3 V/m.

RF line IEC 61000-4-6 · d=f,2

Page 19 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Distance by frequency of transmitter m
Page 19 · click to enlarge
Page 19

Recommended distances between portable and mobile HF communication devices and the AST-300C

The AST-300C is intended for use in an electromagnetic environment that controls radiated RF interference. The customer or user of the AST-300C can help to avoid electromagnetic interference by maintaining a minimum distance between portable and mobile RF communication devices (transmitters) and the ast-300 C, as recommended below, depending on maximum output power of the communication device.

Distance by frequency of transmitter m

150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz

0.12 0.12 0.23

0.38 0.38 0.73

1 1.2 1.2 2.3

10 3.8 3.8 7.3

100 12 12 23

For transmitters with a maximum output power not listed above, the recommended separation distance d in meters (m) may be estimated from the equation for the frequency of the transmitter where P is the maximum output energy of the sender in watts (W), as specified by the transmitting manufacturer. NOTE 1 At 80 MHz and 800 MHz the distance is for the higher frequency range. NOTE 2 This rule may not apply in all situations. Electromagnetic propagation is influenced by absorption and reflection of structures, objects and persons.

Page 20 of the Emstim AST-300C - Electrical Muscle Stimulation user manual — Guaranteed card
Page 20 · click to enlarge
Page 20

Guaranteed card

1. We guarantee that the product is insured against all defects for one year from the date of purchase. There is no cost for accessories or maintenance. The prerequisite is that the product be used in accordance with the instructions contained in the user manual. 2. Costs for accessories can only be incurred if components that are older than one year have to be replaced. No maintenance costs are incurred. 3. Please send the defective product to us or a local dealer. We will take care of it immediately.

Valid for the guarantee 1 year after purchase date

Date of purchase:

Address of the consumer:

Name of the consumer:

Consumer's telephone:

Trader name:

Address of the dealer:

Dealer’s telephone:

Description:

Ask about the Emstim AST-300C - Electrical Muscle Stimulation

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Emstim AST-300C - Electrical Muscle Stimulation

Be the first to ask — other owners or our team will answer.

Original document

Emstim AST-300C - Electrical Muscle Stimulation manual PDF

20 pages·819 KB·Miscellaneous·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…