

For English Parlez-vous français? ¿Habla español? See page 2 Voir page 15 Ver página 28

Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use and reduce the risk of electric shock. Refer to “Recommended sizes of Extension Cords” in the Accessory section of this manual.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
Personal Safety Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
Keep by-standers, children, and visitors away while operating a power tool. Distractions can cause you to lose control.
Electrical Safety Double Insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double Insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Before plugging in the tool, be certain the outlet voltage supplied is within the voltage marked on the nameplate. Do not use “AC only” rated tools with a DC power supply.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Keep handles dry, clean and free from oil and grease.
Avoid accidental starting. Be sure switch is “OFF” before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch “ON” invites accidents.
Remove adjusting keys or wrenches before turning the tool “ON”. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. If operating the power tool in damp locations is unavoidable, a Ground Fault Circuit Interrupter must be used to supply the power to your tool. Electrician’s rubber gloves and footwear will further enhance your personal safety.
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Tool Use and Care Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.
Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Develop a periodic maintenance schedule for your tool.
Do not use tool if switch does not turn it “ON” or “OFF”. Any tool that cannot be controlled with the switch is dangerous and must be repaired.
Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.
Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.
Service Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. For example: internal wires may be misplaced or pinched, safety guard return springs may be improperly mounted.
Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. Any alteration or modification is a misuse and may result in a dangerous condition.
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.
Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools
Secure the material being planed. Never hold it in your hand or across legs. Small workpiece must be adequately secured so that the rotating planer blades will not pick it up during forward motion of the planer. Unstable support can cause the blades to bind causing loss of control and injury.
Check the workpiece for nails, if there are nails, either remove or set them well below intended finished surface. If the planer blades strike objects like nails it may cause the tool to kickback and serious personal injury may result.
Never leave the trigger locked “ON”. Unplug the planer before changing accessories. Before plugging the tool in, check that the trigger lock is "OFF". Accidental start-ups may occur if planer is plugged in while changing an accessory.
Make sure the spring operated automatic retracting rabbet guard returns to blade covering position instantly. The blades are hidden from view and you may be cut if blade is contacted.
Always start the plane before blade is in contact with the workpiece and allow the blade to come to full speed. Tool can vibrate or chatter if blade speed is too slow at beginning of cut and possibly kickback.
After changing blades, rotate the blade drum to make sure blades are not hitting any part of the blade head housing and the blade locking screws are tight. Spinning blades could strike tool housing and damage tool as well as possible injury.

Always hold the tool firmly with both hands for maximum control.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
Never pull the plane backward over the workpiece. Loss of control may occur.
Do not put fingers or any objects into the chip ejector or clean out chips while tool is running. Contact with blade drum will cause injury.
Remove plug from power source if it becomes necessary to remove chips. The blades are hidden from view and you may be cut if blade is contacted.
Never place the plane down until the blade is completely at rest. Surface contact with coasting blade drum may cause the plane to walk out of control.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
Never use dull or damaged blades. Sharp blades must be handled with care. Damaged blades can snap during use. Dull blades require more force to push the tool, possibly causing the blade to break.

This symbol designates that this tool is listed to Canadian Standards by Underwriters Laboratories. This symbol designates that this tool complies to NOM Mexican Standards.
This symbol designates that this tool is listed by Underwriters Laboratories.
This symbol designates that this tool is listed by Underwriters Laboratories, and listed to Canadian Standards by Underwriters Laboratories.
This symbol designates that this tool is listed by the Canadian Standards Association.


Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.
BUTTON


Model number 1594 Voltage rating 120 V 50 - 60Hz Amperage rating 6.5 A No load speed n0 16,500/min
Maximum Capacities Planing depth 0 - 3/32" (0 - 2.6mm) Rabbeting depth 0 - 5/16" (0 - 9mm) Planing width 3-1/4" (82mm)

CHIP EXTRACTION The planer comes with two chip exhaust ports, which may be used with a chip bag (Fig.2) or a shop vacuum and vacuum connector (Fig.3) to keep your work environment cleaner. The chip bag or vacuum connector may be attached to either end of the exhaust port. Moving the port selector lever to position 1 (towards front of tool) discharges chips to the left, while position 2 (towards rear of tool) discharges chips to the right. (Fig. 1) Included is the VAC002 adapter that will connect the hood to 1-1/4” and 1-1/2” vacuum hoses. An adapter to connect the hood to 2-1/2" hoses is also available separately.
EXHAUST
PORTS
(OPTIONAL)
Always changes both blades at the same time. Otherwise, imbalance can cause vibration and reduce the useful service life of the tool. Use only blades designated for use with this model, because other blades can cause vibration, decrease performance and may not clamp securely in blade holder. Do not attempt to sharpen or use re-sharpened any TC blades. To remove the blades: 1. Rotate the blade drum until the clamping jaw is parallel to the planer shoe. 2. Loosen the three clamp screws by about one revolution each. (It is not necessary to remove the clamping jaw.) (Fig.4) 3. Slightly rotate the blade drum and use a piece of wood to push the blade sideways and out from under the clamping jaw. Make sure to keep your fingers away from the sharp edges of the blade. If the blade is gummed and difficult to remove, you may clean the blade and clamp with mineral spirits, lacquer thinner or alcohol. (Fig. 5)
Wear protective gloves when changing planer blades. Edges are sharp and may cause injury.
CARBIDE BLADES Mini TC planer blades have two cutting edges, and may be reversed when one of the cutting edges becomes dull or chipped. (Fig. 6) Before any work on the machine itself, pull the power plug.


JAW
CLAMPING
INSTALLING AND ADJUSTING MINI

DRUM
FRONT
SHOE
BLADE HOLDER RIDGE


INSTALLATION PROCEDURE 1. Align the groove on top of the blade with the ridge of the blade holder and carefully slide the blade onto the blade holder, as shown in Figure 6. 2. Using a block of wood push the TC blade back towards the blade holder so that the inner side of the blade is pressed against the sloping part of the blade holder. (This will ensure that the blades are level.) 3. Then tighten the Torx clamping screws using the correct tightening sequence (1,2,3), as shown in Figure 4, and your planer is ready for use. Blade Retainer Screws - Under normal circumstances, the position of the retainer on the mini TC blade holders does not require readjustment. If fact, the screws that attach the retainer to the blade holder are factory sealed with a yellow fastening compound that should not be disturbed. However, if you believe that adjustments must be made, proper adjustment is critical, and it is best performed by a Bosch Factory Service or Bosch Authorized Service Center.

STEEL BLADES The 1594 Planer can be converted to accept large HSS blades. The conversion requires the optional PA1204 HSS Blades with Retainers (pair). (Fig. 7) Additional pairs of HSS blade, the PA1205 large HSS blades, can also be purchased separately.



HSS BLADE
HOLDERS AND RETAINERS 1. Rotate the blade drum until the clamping jaw is parallel to the planer shoe. 2. Loosen the three clamp screws completely and remove the screws and clamping jaw. 3. Slightly rotate the blade drum and use a piece of wood to push the blade, holder and retainer off of the blade drum. Make sure to keep your fingers away from the sharp edges of the blade. If the blade is gummed and difficult to remove, you may clean the blade and clamp with mineral spirits, lacquer thinner or alcohol. 4. Rotate the blade drum 180° and repeat the procedure to remove the second blade.

To remove the blades: 1. Rotate the blade drum until the clamping jaw is parallel to the planer shoe. 2. Loosen and remove the three clamp screws with the Torx key. 3. Also remove the clamping jaw. 4. Slightly rotate the blade drum and use a piece of wood to push the blade and retainer sideways and out of the blade drum. Make sure to keep your fingers away from the sharp edges of the blade. If the blade is gummed and difficult to remove, you may clean the blade and clamp with mineral spirits, lacquer thinner or alcohol. Rotate the blade drum 180° and repeat the procedure to remove the second blade.


RESHARPENING HSS BLADES Worn or dull HSS plane blades can be re- sharpened. The optimal blade angle of 50º should be maintained when sharpening. Once a total of 6 mm of steel has been removed from tips of the blades, both blades must be replaced because the minimum HSS blade height is 23 mm from back to tip.
LEVELING OF HSS BLADES A PA1206 HSS Blade Leveling Fixture (optional accessory) is required to level new or resharpened HSS blades. (Not necessary with the PA1204 HSS Blades and Retainers, which are leveled at the factory.) 1. Place the blade and blade retainer on the leveling fixture and make sure that the blade retainer engages in the grooves intended for this purpose. (Fig. 9) 2. Press the plane blade against the stop in front of the cutting edge to achieve the proper depth and evenness (levelness) and with the blade retainer in this position and tighten it with the locking screws. This will automatically adjust the blade to the correct height and levelness. 3. Tighten the retainer screws. 4. Remove blade and retainer assembly from the leveling fixture. 5. Repeat the procedure for the second blade.

Hold the tool with both hands while starting the tool, since torque from the motor can cause the tool to twist.
REST
To turn tool "ON": depress the “Lock-Off” release button from either side and squeeze the trigger switch.
To turn the tool "OFF": release the trigger switch and it will return to "OFF" position automatically.
steadily until the full length of the rear shoe passes over the edge of the workpiece. (Fig. 10)
To increase switch life, do not turn switch on and off while tool and drum are held against a workpiece.
PLANING ACTION Proper planing action helps to achieve the desired result. With practice and experience, it will become second nature. Make sure that the workpiece is held in place securely on your work surface, and standing comfortably, hold the planer firmly with both hands.
The motor may stall if improperly used or overloaded. Reduce the pressure (feed rate) or depth of cut to prevent possible damage to the tool if the motor labors.
DEPTH OF CUT & FEED RATE The cutting depth (planing depth) is determined by the difference in height between the adjustable front shoe and the fixed rear shoe of the planer. The depth knob adjusts the front shoe, which retracts and exposes the blade and determines the amount of material removed from the workpiece. The cutting depth range is from 0 to 3/32” or 2.6 mm per pass. (Fig. 1)
rather than with the grain, a shallower cut and/or slower feed rate is required. Whenever possible, test by planing a similar piece of scrap material.
Use multiple, progressive cuts to achieve the total desired depth.
Start with a shallow cut. If the plane moves freely through the workpiece with no excessive load on the motor, the depth setting can be increased before the next cut. (Do not change depth of cut while planing.)
The appropriate depth of cut and feed rate depends on the workpiece material:
When near the desired total depth, re-adjust the planing depth to a shallow setting for the final cut to obtain a good surface finish.
To avoid clogging and/or damage to the motor, a more shallow (thin) cut and/or a slower feed rate may be needed if the material has any of these characteristics: hardness; gumminess, sappiness, moisture, paint, varnish and/or knots. Also, when planing against the grain or across the grain
Adjusting the Depth of Cut: Rotate depth adjustment knob clockwise until the indicator is aligned with the desired cutting depth on the depth scale (Fig. 1).

PARK REST STAND The park rest stand automatically springs down to help keep the blade from coming in contact with the work surface when planer is not in use (Fig. 11). The park rest stand is designed to swing up and out of the way by it itself when the back of the plane crosses the leading edge of the workpiece (Fig. 10). It will also swing up when planing begins in the middle of the work piece (in from the edge of the work piece).
REST
UNCLOGGING THE CHIP EXHAUST
SYSTEM Remove plug from power source if it becomes necessary to manually remove chips. The blades are hidden from view and you may be cut if contacted.
To minimize the possibility of clogging, make sure:
(See FEED RATE & DEPTH OF CUT)
If clogging occurs, stop the planer and move the chip eject lever back and forth. If this does not break up the clog, unplug the planer and carefully insert a screwdriver or similar object into the dust port to break up the clog.
DELUXE BEVEL GUIDE FENCE The Deluxe Bevel Guide Fence (Fig. 12) can be used to cut various desired widths, with the additional capability of guiding the planer on any angle up to 45 degrees, to allow edge chamfering (Fig. 13).
Installing the angle fence: Place the wing knob through the appropriate hole in the guide bracket and screw into the housing. Securely tighten wing knob (Fig. 1).
Setting the cutting width: Loosen wing knob and using the width scale, slide the fence along the guide bracket to the desired position. Securely tighten wing knob (Fig. 1).
Setting the cutting angle: Loosen round knobs and pivot the fence to the desired position. Securely tighten round knobs (Fig. 1).
9 mm max · 82 mm max · 45°

STRAIGHT GUIDE FENCE The optional Straight Guide Fence can be used to cut various desired widths. (Fig. 14)
Installing the guide fence: Place the wing knob through the appropriate hole in the guide bracket and screw into the housing. Securely tighten wing knob.
Setting the cutting width: Loosen wing knob and slide the fence along the guide bracket to the desired position. Securely tighten wing knob. Be certain that the flat washer (supplied) is fitted between the bottom of the guide fence and wing knob or the guide fence is likely to slip.
GUIDE FENCE
DRIVEN PULLEY
RABBETING DEPTH STOP The optional rabbeting depth stop accessory (Fig. 1) allows the user to set any rabbeting depth from 0 to 5/16 inch. For best results, it is important that the blade be properly aligned (See "BLADE ALIGNMENT"). The width of the rabbet is controlled by the width fence. The final depth is achieved by repetitive cutting until the rabbeting depth guide contacts the workpiece. The maximum rabbeting depth is 5/16"










Setting the rabbet depth: Loosen wing knob and using the depth scale on the rabbeting depth stop, set the desired rabbet depth. Securely tighten wing knob.
DRIVE
BELT DRIVE
BELT COVER
DRIVE BELT The drive belt is a normal maintenance part and should be inspected periodically for wear. If the drive belt shows signs of drying out, cracking or tearing, it should be replaced. If the drive belt will not track properly or comes off the pulleys, it should be replaced.
Installing new drive belt: Loosen screw and remove the drive belt cover. Cut and remove the worn drive belt. Before installing the new drive belt, clean both pulleys thoroughly. First place the new drive belt onto the drive pulley then rotate clockwise while pushing the belt onto the driven pulley. Reinstall the drive belt cover and securely tighten screw (Fig. 15).
9 mm max · 82 mm max

Service Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Autho- rized Bosch Service Station.
Center or Authorized Bosch Service Station. Bearings which become noisy (due to heavy load or very abrasive material cutting) should be replaced at once to avoid overheating or motor failure.
Cleaning To avoid accidents always disconnect the tool from the power supply before cleaning or performing any maintenance. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air. Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.
TOOL LUBRICATION Your Bosch tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regreased with a special gear lubricant at every brush change.
CARBON BRUSHES The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. Only genuine Bosch replacement brushes specially designed for your tool should be used.
Certain cleaning agents and solvents damage plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia. Clean the park rest shoe regularly and ensure that it springs back freely.
BEARINGS After about 300-400 hours of operation, or at every second brush change, the bearings should be replaced at Bosch Factory Service
If an extension cord is necessary, a cord with adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3-wire extension cords that have 3-prong plugs and receptacles. NOTE: The smaller the gauge number, the
120 VOLT ALTERNATING CURRENT TOOLS ! WARNING
Cord Size in A.W.G. Wire Sizes in mm2
Cord Length in Feet Cord Length in Meters
25 50 100 150 15 30 60 120
3-6 6-8 8-10 10-12 12-16
18 16 16 14 0.75 0.75 1.5 2.5 18 16 14 12 0.75 1.0 2.5 4.0 18 16 14 12 0.75 1.0 2.5 4.0 16 16 14 12 1.0 2.5 4.0 — 14 12 —
heavier the cord.
Woodrazor reversible micro grain
High-Speed Steel Blades ** HSS Blade Leveling Fixture ** High-Speed Steel Blades with Retainers **
TC blades (2) * T-30 Torx blade wrench * Deluxe Bevel Guide Fence * Vacuum hose adapter ** Straight Guide Fence ** Rabbeting depth stop ** Chip bag *
(*= standard equipment) (**= optional accessories)
Tool’s Ampere · Rating
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.