


Installation Manual ENGLISH

7. Do not defeat the purpose of a polarized or grounded mains plug. A polarized plug has dissimilar prongs (one wider than the other) to ensure correct polarity, while a grounded plug has an additional 'ground' prong provided for your safety. If the plug supplied with the apparatus does not fit into your outlet, consult an electrician for advice. 8. Protect the power-supply cord from being walked on or pinched, particularly close to plugs, receptacles and the point where it exits from the apparatus. 9. Only use attachments and accessories (including stands, tripods, mounting brackets and housings) specified or recommended by the manufacturer. 10. Unplug the apparatus during lightning storms and when unused for extended periods. 11. Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 12. Servicing is required when the apparatus does not function in the normal way, has been dropped, if liquid has been spilled on it, or if it has been exposed to rain or water. Unplug the unit from the outlet and refer servicing to qualified service personnel. 13. An all-pole mains switch with contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building.



Power
LTC 04x5/1x and /2x LTC 04x5/5x and /6x

To open the quick-connect, push in on the tabs. Connections are not polarity sensitive Use stranded or solid wire AWG16 to AWG22, cut back 10mm (0.4") of insulation.
Y/C output (LTC 0455/x1 only)
2 GND C
3 Y
LENS MOUNTING
Pin Y/C Socket


Notes: 1. To optimize picture sharpness in both bright and low-level lighting, it is recommended to adjust the back focus when carrying out the set-up procedure. The camera's unique 'Lens Wizard' allows focusing at maximum lens opening to ensure that the object of interest always remains in focus. 2. When back focusing vari-focus lenses, it must be possible to obtain a sharp picture in both wide-angle and tele positions, and for both far and near focus. 3. When back focusing zoom lenses, ensure the object of interest remains in focus throughout the entire zoom range of the lens. (See Advanced Set up).
The camera can be mounted from the top or bottom.

The camera will normally give an optimal picture without the need for further adjustments. However for special circumstances advanced set up options are available.
How to use the 5 keys

Press the menu button
SHUT/AGC MENU
LEVEL 0 SHUT/AGC BLC OFF COLOR ATW SYNC LINE LOCK VPHASE 0¡
EXIT
EXIT
COLOR MENU
WHITE BAL ATW RED-GAIN 0 BLUE-GAIN 0
EXIT
Press the menu button for more than 5sec.
INSTALLER
DETECTED LENS DCIRIS SET BACK FOCUS NOW
VERSION 00.0010.XX LENS AUTO SPEED FAST WIZARD
EXIT
LENS WIZARD
COAX COMM ON
DEFAULTS
DETECTED LENS VIDEO SET BACK FOCUS NOW
EXIT
SET LVL
EXIT

*Note: If the camera (LTC 0455/x1 only) is in black & white high sensitivity mode (via NightSense™), the color settings and color menu are not accessible. The NightSense™ sensitivity boost must be selected OFF to make color adjustments.

SHUTTER AES (AES) Auto-shutter sets the optimum shutter speed FL for manual iris lenses. (FL) Flickerless mode avoids OFF interference from light sources (recommended for use with video-iris or DC-iris lenses only).
AGC ON/OFF Automatic gain control
AUTOBLACK ON/OFF Autoblack automatically increases the visibility of details.
Nightsense™* extends the low-light performance of the camera. AUTO mode, the camera automatically inches to monochrome in low-light conditions. Forced mode, the picture remains a high-sensitivity monochrome image. Some active noise or white spots may appear in the picture.
EXIT Exit the menu.
*Note: NightSense™ is only available on the LTC 0455/x1 cameras.
ATW: Auto tracking white balance allows the camera to automatically adjust for optimal color reproduction. AWB HOLD: Puts the ATW on hold and preserves the color settings.
RED- GAIN* -5 - 0 - +5 Offset factory white point alignment (reducing red introduces more cyan).
BLUE- GAIN* -5 - 0 - +5 Offset factory white point alignment (reducing blue introduces more yellow).
EXIT Exit the menu.
*Note: For special scene conditions only, it will be necessary to change the white point offsets.
Function Selection Description · Function Selection Description

VERSION Read-only firmware release number (for service purposes).
LENS AUTO Automatically detect lens type. A different lens type can be selected.
SPEED FAST Selects the response time of DC-iris lenses. Some lenses require slow lens control to avoid overshoots.
WIZARD Access the lens wizard menu.
COAX COM ON/OFF If OFF Bilinx™ communication is disabled
DEFAULTS Select next menu Return all set-up settings to factory defaults.
EXIT Exit the menu.
SET BACK FOCUS NOW Back focus the lens (see 'Back focus adjustment'). The scene is focused at maximum lens opening to ensure that the object of interest remains in focus in bright and low-light conditions.
SET LVL When a Video-iris lens is detected, a level potentiometer is displayed to obtain the best picture performance. The lens wizard includes a level detector meter that must be set to the center using the potentiometer for best results.
EXIT Exit the menu.
Function Selection Description · Function Description


Bosch Security Systems B.V.
P.O. Box 80002
www.bosch-sicherheitssysteme.de
3122 165 23071 04-05
© 2003 Bosch Security Systems B.V.
Subject to change Printed in Portugal
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.