Instruction/ maintenance manual of the product ME10-GN Cecilware
Go to page of 11
ME10-GN ME15-GN AUTOMATIC GAS WATER BOILER Operation Manual NQ24A 12-2006 CONTENTS Specifications Start up Instructions Trouble Shooting Guide Parts List Wiring Diagram 18 Gauge Type 304L Stainless Steel construction to resist corrosion.
WATER INLET (1/4 " FLARE) 16.0 3.4 SIDE ACCESS DOOR (SLIDES UP) OVERFLOW THERMOMETER 4.0 "B" 14.0 5.0 CAUTION HOT SURFACES ME10-GN NP87A TEMPERATURE CONTROL NOTE: UNIT IS SUPPLIED WITH A GROUNDED 120V-15A LINE CORD AND PLUG (NEMA 5-15P).
2 FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. THIS INSTALLATION MUST CONFORM WITH THE NATIONAL FUEL GAS CODE , ANSI Z223.1 (LATEST EDITION). WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH.
3 ASSEMBLY: T he four legs and vent cap drain are packed separately with the water boiler. Install legs by tilting the water boiler on its side and screwing the legs into the leg supports until hand tight.
4 NOTE: On the first lighting it may be necessary to hold the dial for a longer period to allow trapped air to escape from the line. DIAL SETTINGS AND CORRESPONDING WATER TEMPERATURES: “1”= 50F, “10”=198F RELIGHTING: Shut off all gas and wait approximately 5 minutes before relighting the pilot.
5 BURNER: The b urner is factory set for maximum performance. Should further adjustments be required loosen slotted hex screw on side of ventur i and rotate air shutter until flame with soft blue inner core is obtained. BURNER REMOVAL: The burner can be removed with the unit standing in operating position.
.
.
No. PART # DESCRIPTION ME10-GN ME15-GN 1 B012A HEYCO BUSHING STRAIGHT, SMALL 1 1 2 B033A TERMINAL BLOCK 3 POSITION 1 1 3 C032S LINE CORD W/ PLUG 120V 15A 1 1 4 CD257 WATER INLET VALVE 120V 1 1 5 CH32A.
B) Water Inlet Valve Test Turn power OFF. If the water level rises inside a partially filled tank, the Water Inlet Valve is leaking. Disconnect wires from the Water Inlet Valve coil and connect a 2 wire line cord to the terminals. Plug it into a 115V outlet.
CECILWARE CORPORATION RED WHT BLU YEL WATER LEVEL CONTROL WATER LEVEL PROBES GND 6 COMMON 4 L-LEVEL 5 H-LEVEL 3 AC-2N 1 FILL 2 AC-1L WATER LED L1 N WATER INLET VALVE POWER LIGHT GND GRN POWER SWITCH N.
An important point after buying a device Cecilware ME10-GN (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cecilware ME10-GN yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cecilware ME10-GN - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cecilware ME10-GN you will learn all the available features of the product, as well as information on its operation. The information that you get Cecilware ME10-GN will certainly help you make a decision on the purchase.
If you already are a holder of Cecilware ME10-GN, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cecilware ME10-GN.
However, one of the most important roles played by the user manual is to help in solving problems with Cecilware ME10-GN. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cecilware ME10-GN along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
