Instruction/ maintenance manual of the product MWHUS Chief
Go to page of 12
INSTALLATION INSTRUCTIONS Instrucciones de inst alación Installationsanleitung Instruções de Inst alação Istruzioni di inst allazione Installatie-instructies Instructions d´installation Medium F.
MWH Installation Instructions 2 DISCLAIMER Milestone A V T echnologies, and its affiliated corporations and subsidiaries (collectively , "Milestone "), intend to make this manual accurate and complete.
Installation Instructions MWH 3 TOOLS REQUIRED FOR IN ST ALLA TION AND P ARTS 7/32" (Ø 6mm) x1 I/M B (2) F (4) C (1) D (1) A (1) E (4) G (4) H (4) 5/16 x 2- 1/2" 5/16".
MWH Installation Instructions 4 DIMENSIONS Figure 1 24.90 632 3.43 87 18.61 473 B 15° C 5° 2.5° Tilted Down Tilted Up Extended Retracted Tilt Adjustment Roll Adjustment .
Installation Instructions MWH 5 Mount Inst allation W ARNING: IMPROPER INST ALLA TION CAN LEAD TO MOUNT F ALLING C AUSING SERIOUS PERSONAL INJURY O R DAMAGE TO EQUIPMENT! It is the inst aller’s resp.
MWH Installation Instructions 6 Cover Inst allation T o install channel covers: 1. Install upper and lower wall channel covers (B) by tipping cover top down and positioning as shown in en d view of figure below . (See Figure 4) 2. T ap firmly across bottom of channels to lock in place as shown in figure below .
Installation Instructions MWH 7 Display Inst allation If the mounting pattern of the display being installed is a VESA standard 200 x 200 pattern the mounting b uttons can be installed directly to the back of the di splay . If the di splay has any other mounting pattern an interface bracket must be obtained before proceeding.
MWH Installation Instructions 8 Figure 7 (E) x 4 x 4 From Display (A) x 4 ADJUSTMENTS Pitch T ension Adjustment T o adjust display pitch tension: 1. With display installed, tight en or loosen two screws , one on each side, using the 5/32” hex wrench.
Installation Instructions MWH 9 Roll Adjustment The MWH allows for the horizontal alignment (R oll)of the display to be adjusted up to 2 deg. rig ht or left to level the display after installing. T o ad just Roll : 1. Loosen the roll tensions adju stment nut located on the back side of the faceplate assemb ly .
MWH Installation Instructions 10.
Installation Instructions MWH 11.
MWH Installation Instructions Chief Manufacturing, a division of Milestone A V T echnologies 8831-000009 RevI © 2008 Milestone A V T echnologies www .chiefmfg.com 07/08 USA/International A 8401 Eagle Creek Parkway , Savage, MN 55378 P 800.582.6480 / 952 .
An important point after buying a device Chief MWHUS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chief MWHUS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chief MWHUS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chief MWHUS you will learn all the available features of the product, as well as information on its operation. The information that you get Chief MWHUS will certainly help you make a decision on the purchase.
If you already are a holder of Chief MWHUS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chief MWHUS.
However, one of the most important roles played by the user manual is to help in solving problems with Chief MWHUS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chief MWHUS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
