Instruction/ maintenance manual of the product Version-1.4_12_03_08_E Clearaudio
Go to page of 16
Ovation Hi-Fi Components clearaudio electronic GmbH Spardorfer Str. 150 ● D-91054 Erlangen ● Tel. +49(0) 9131/40 300 100 ● FAX +49(0) 9131/51683 www.clearaudio.de ● www.analogshop.de ● info@cl earaudio.de /clearaudio copyright 2012 User manual Made in Germany Version-1.
Ovatio n User manual Page 2 clearaudio elect ronic GmbH 2012 Dear clearaudio -customer, you have purchased a state-of-the-art turntable, the Ovation , a world class product of clearaudio electronic GmbH.
Ovatio n User manual Page 3 clearaudio elect ronic GmbH 2012 User manual 4 – 14 Contents 1. Packaging overview 4 2. Set-up and operation 5 3. Service 12 4.
Ovatio n User manual Page 4 clearaudio elect ronic GmbH 2012 1. Packaging overview The clearaudio Ovation -turntable is delivered in specially designed custom packaging. Please check the contents according to the following list before you set up your new clearaudio Ovation -turntable.
Ovatio n User manual Page 5 clearaudio elect ronic GmbH 2012 2. Set-up and operation The Ovation -turntable consists of several elements, as described in section 1 (Packing overview). To simplify set up some of the components are pre-assembled at the factory.
Ovatio n User manual Page 6 clearaudio elect ronic GmbH 2012 2.1 Place the pre-mounted chassis on your hi-fi rack or another suitable base. 2.2 Please remove the protective seal from the bearing shaft and place two drops of the synthetic bearing oil (also available at: www.
Ovatio n User manual Page 7 clearaudio elect ronic GmbH 2012 2.3 Very carefully place the upper bearing housing carefully onto the bearing shaft. To avoid damage make sure you slide the upper bearing part slowly and carefully on to the polished ceramic shaft.
Ovatio n User manual Page 8 clearaudio elect ronic GmbH 2012 Please note: The marks (dots) on the sub-platter and the top of the bearing have been carefully measured. Please make sure they align exactly as shown in picture below: 2.5 Now carefully place the platter onto the bearing.
Ovatio n User manual Page 9 clearaudio elect ronic GmbH 2012 2.6 Please check with the bubble level gauge that your Ovation turntable is in a levelled position. You can adjust each of the turntable feet to level the turntable. Best results will only be obtained with the turntable in a completely level situation.
Ovatio n User manual Page 10 clearaudio elect ronic GmbH 2012 1. Carefully install first the cables trough the smaller fitting in the mounting base until the position and cable cover (attached on the cable) fits in the cutout of the mounting base.
Ovatio n User manual Page 11 clearaudio elect ronic GmbH 2012 Now you can connect the Ovation turntable to the mains supply. 2.8 Fine speed adjustment The motor adjustment is already pre set at the factory. During transportation or due to contamination on the sensor or the sensor ring some small speed deviations can occur.
Ovatio n User manual Page 12 clearaudio elect ronic GmbH 2012 On the rear (close to power supply input) of your turntable there are three setting trimmers: - left trimmer = setting 33 1/3 rpm (nea.
Ovatio n User manual Page 13 clearaudio elect ronic GmbH 2012 3. Service If any service or repair on all clearaudio products is necessary, please contact your dealer / distributor or contact clearaudio direct. We can inform you about your nearest service location.
Ovatio n User manual Page 14 clearaudio elect ronic GmbH 2012 4. Special directions The clearaudio Ovation does not require any extensive maintenance. If the Ovation turntable is not used for a long time disconnect the motor from the mains supply.
Ovatio n User manual Page 15 clearaudio elect ronic GmbH 2012 5. Technical data Construction: Resonance-optimised chassis, Recommended tonearm with magnetic bearing technology Operating speeds: 33.
Ovatio n User manual Page 16 clearaudio elect ronic GmbH 2012 The warranty period for the Ovation turntable is 2 years. To achieve the extended clearaudio warranty of 5 years, it is necessary that.
An important point after buying a device Clearaudio Version-1.4_12_03_08_E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Clearaudio Version-1.4_12_03_08_E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Clearaudio Version-1.4_12_03_08_E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Clearaudio Version-1.4_12_03_08_E you will learn all the available features of the product, as well as information on its operation. The information that you get Clearaudio Version-1.4_12_03_08_E will certainly help you make a decision on the purchase.
If you already are a holder of Clearaudio Version-1.4_12_03_08_E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Clearaudio Version-1.4_12_03_08_E.
However, one of the most important roles played by the user manual is to help in solving problems with Clearaudio Version-1.4_12_03_08_E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Clearaudio Version-1.4_12_03_08_E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
