Instruction/ maintenance manual of the product GDO 18 CyberResearch
Go to page of 42
Displays USER’S MANUAL VER. 1 • 2002 No part of this manual may be reproduced without permission GDO 18 Series 18" TFT LCD Flat-panel Displays GDO 18: 18" Flat-panel Display GDO 18-T: GDO 18 w/ Resistive Touchscreen ® CyberResearch ® , Inc.
.
©Copyright 2002 All Rights Reserved. 2002 The information in this document is su bject to change without prior notice in order to improve reliability, desi gn, and function and does not represent a commitment on the part of CyberResearch, Inc. In no event will CyberResearch, Inc.
Intentionally Blank.
P REFACE FCC Compliance Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter ference when the equipment is operated in a residential installation.
User’s Manual i v Class B ITE (Following European Sta ndard EN 50082-2) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause r adio interference in which case the user may be required to take adequate measures.
User’s Manual v Important Safety Instructio n s Please read the following instructions carefully. This manual should be retained for future use. 1. To clean the LCD monitor screen, first, make sure the monitor is in the Power Off mode. Unplug the monitor from its power source before cleaning it.
User’s Manual vi • The monitor has been dropped or the case has been damaged..
User’s Manual vii T ABLE OF C ONTENTS CH A P T E R 1 ................................................................................................................................1 The LCD Monitor...................................................
User’s Manual v ii i T ABLE OF F IGURES Figure 1- 1: The LCD Monitor Panel and Controls ________________3 Figure 1-2: LCD Monitor’s Rear Ports _________________________4 Figure 1- 3: Angle Setting.
C HAPTER 1 The LCD Monitor Your new LCD Monitor Your LCD monitor has been designed to be versatile, ergonomic and user - friendly. The LCD monitor is c apable of displaying most standards, from 640 x 480 VGA to 1280 x 1024 SXGA. The digital controls located on the front panel allow the user to easily adjust the monitor’s display parameters.
User’s Manual 2 Using a computer for an extended period of time with a poor workstation se t - up and incorrect working habits c an cause health problems. The sc ience of ergonomics studies the relationship between health and a suitable working environment.
User’s Manual 3 Figure 1 - 1: The LCD Monitor Panel and Controls 1 . LCD Screen The RGB LCD monitor screen is capable of producing most display standards. 2 . Function Contro l Buttons These two buttons allow you to select one of the control functions.
User’s Manual 4 5 . Power- On Indicator This LED indicator lights when the power is on. The LED indi cator will blink when the LCD monitor is in Power Saving mode. 6 . Monitor Swivel Base The monitor swivel base supports the LCD panel and changes the monitor angles.
User’s Manual 5 2 . AC Power Connector Connect the power cable t o this AC power connector. 3 . PS/2-Type Connector for Touchscreen (optional) Connect this PS/2 6-pin connector to your PC’s R S-232 9- pin serial port connector to use the optional touchscreen.
User’s Manual 6 Figure 1 - 3: Angle Settings Do not force the monitor past its maximum extension in either direction. You could damage the monitor and the monitor stand. Positioning Take a moment to prepare a suitable place to set up your workstation.
User’s Manual 7 • Do not place the LCD monitor in direct sunlight or near a window. Moisture and direct sunlight exposure can be seriously damaging. Connecting AC Power Please refer to the following instructions for connecting AC power to the LCD monitor.
User’s Manual 8 Figure 1 - 5: Connecting the LCD Monitor to the PC 3. If your PC has a graphic card with a 24 - pin DVI connector, you should connect it with the digital 24- pin DVI signal cable. 4. Make sure the signal cable head is securely connected to the VGA port of your PC.
User’s Manual 9 2. Connect the other end of the 1.5M sound cable to the LCD monitor’s line- i n jack. Please refer to Figure 1 - 6 . Figure 1 - 6: Connecting the Stereo Speakers 3. You can adjust the sound volume of the stereo speakers by u s ing the speaker volume control function on the OSD (On - Screen Display).
User’s Manual 10 Figure 1 -7 : Connecting the Optional Touchscreen Cable 2. Connect the D - su b 9 - pin RS-232 connector end of the PS/2 to RS-232 cable provided with the optional t ouchscreen package to the 9 - pin RS-232 serial port at the back of your PC.
C HAPTER 2 The Display Controls The LCD Monitor Display Controls This chapter covers the LCD monitor’s On-Screen Display (OSD). Using the OSD y ou can adjust the contrast, brightness, display position, display clarity, and color temperature, etc. You can also adjust the stereo speaker volume and set OSD parameters.
User’s Manual 12 Figure 2 - 1: The OSD Main Menu The control functions are grouped into seven categories as shown on the Main Menu. Continue pressing the Function buttons to sc roll through the menu item. Press the Adjustment buttons to enter the sub- menu of each function group.
User’s Manual 13 Basic Setting CONTRAST To adjust the contrast level of the display. B R IGHTNESS To adjust the brightness level of the display. VIDEO LEVEL To fine tuning the matching input signal voltage level. Perform this function whenever the graphics card is changed.
User’s Manual 14 Miscellaneous Menu AUDIO VO LUME To adjust the audio volume of the monitor’s speakers. (Only available in the models with built -i n speakers.) OSD H - POSITION To adjust the horizontal position of the OSD menu. OSD V- POSITION To adjust the vertical position of the OSD menu.
User’s Manual 15 Pr ess the lower Function Control button (second button) to enable the small Brightness icon. Use the Adjustment Control button to increase (+) or de crease (-) the brightness level. Press the upper Adjustment Control button (third button) to enable the small volume icon.
.
A PPENDIX A Troubleshooting Troubleshooting Procedures This LCD Monitor was pre - adjusted in the factory with standard VGA ti m ing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected.
User’s Manual 18 horizontal dark and light lines appear. The number of lines i n crea ses as you press the button. Now press the bottom (or top) Adjustment Control button until the lines disappear and you have a clear display. PROBLEM: There is no LCD Display If there is no display on the LCD, please perform the following steps: 1.
19.
20.
21.
22.
23.
24.
25.
Intentionally Blank 26.
Product Service Diagnosis and Debug CyberResearch, Inc. maintains technica l support lines staffed by experienced Applications Engineers and Technicians. There is no charge to call and we will return your call promptly if it is received while our li nes are busy.
Intentionally Blank 28.
Warranty Notice CyberResearch, Inc. warrants t hat this equipment as furnished will be fr ee from defects in material and workman ship for a period of one year from the conf irmed date of purchase b y the original buye r and that upon written notice of any such defect, CyberResearch, Inc.
Intentionally Blank 30.
.
CyberResearch, Inc. 25 Business Park Drive Branford, CT 06405 USA P: (203) 483-8815; F: (203) 483-9024 www.cyberresearch.com.
An important point after buying a device CyberResearch GDO 18 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CyberResearch GDO 18 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CyberResearch GDO 18 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CyberResearch GDO 18 you will learn all the available features of the product, as well as information on its operation. The information that you get CyberResearch GDO 18 will certainly help you make a decision on the purchase.
If you already are a holder of CyberResearch GDO 18, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CyberResearch GDO 18.
However, one of the most important roles played by the user manual is to help in solving problems with CyberResearch GDO 18. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CyberResearch GDO 18 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
