Instruction/ maintenance manual of the product NANO-PV-D510A Dialogue Tech
Go to page of 169
NANO-PV -D510A User Manual Page i IEI T echnology Corp. User Manual NANO-PV -D510A MODEL: NANO-PV -D510A EPIC SBC with Intel® Atom™ D510 Dual Core Processor , Gigabit Ethernet, USB, PCI-104, PCIe Mini Card, RS-232, RS-232/422/485, SA T A, Comp actFlash® T ype II RoHS Compliant Rev .
NANO-PV -D510A User Manual Page ii Revision Date Version Changes 25 May , 2010 1.00 Initial releas e.
NANO-PV -D510A User Manual Page iii Copyright COPYRIGHT NOTICE The information in this do cument is subject to chan ge without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.
NANO-PV -D510A User Manual Page iv T able of Content s 1 INTRODUCTION.......................................................................................................... 1 1.1 I NTRODUCTION .......................................................
NANO-PV -D510A User Manual Page v 3.2.12 PCI-104 Connector ........................................................................................ 25 3.2.13 PCIe Mini Car d Slot ........................................................................
NANO-PV -D510A User Manual Page vi 4.6.2 Audio Cable Installation .................................................................................. 51 4.6.3 Keyboar d/Mouse Connector ...................................................................
NANO-PV -D510A User Manual Page vii 5.5.2 Boot Device Priority ...................................................................................... 102 5.5.3 Har d Disk Drives .........................................................................
NANO-PV -D510A User Manual Page viii D.3.2 Enable the DIO Output Function .................................................................. 145 E W A TCHDOG TIMER .......................................................................................
NANO-PV -D510A User Manual Page ix List of Figures Figure 1-1: NA NO-PV-D510A ...................................................................................................... ... 2 Figure 1-2: Connectors .........................................
NANO-PV -D510A User Manual Page x Figure 4-1: CompactFlash® Card Inst allation ........................................................................... 41 Figure 4-2: PCIe Mini Card Installation ....................................................
NANO-PV -D510A User Manual Page xi Figure B-14: Co mpress Image.......................................................... Error! Bookmark not defined. Figure B-15: Image Cr eation Conf irmation ..................................... Error! Bookmark not defined.
NANO-PV -D510A User Manual Page xii List of T ables Table 1-1: Technical Specifications ............................................................................................ .. 7 Table 3-1: Peripheral Interface Co nnectors .....................
NANO-PV -D510A User Manual Page xiii Table 4-3: AT/ATX Power Select Jumper Settings .................................................................... 44 Table 4-4: Clear BIOS Jumper Settings .........................................................
NANO-PV -D510A User Manual Page xiv BIOS Menus BIOS Menu 1: Main .............................................................................................................. ......... 65 BIOS Menu 2: Adva nced .......................................
NANO-PV -D510A User Manual Page 1 Chapter 1 1 Introduction.
NANO-PV -D510A User Manual Page 2 1.1 Introduction Figure 1-1: NANO-PV-D510A The NANO-PV-D5 10A EPIC CPU card is an embedded 45 nm Intel® Atom™ processo r platform. The Intel® Atom™ dual-core processor D510 embedded on the NANO-PV-D510A has a 1.
NANO-PV -D510A User Manual Page 3 1.3 Connectors The connectors on the NA NO-PV-D510A are shown in the figure below. Figure 1-2: Connectors 1.4 Dimensions The main dimensions of the NANO-PV-D510A are sh own in the diagram below.
NANO-PV -D510A User Manual Page 4 Figure 1-3: NANO-PV-D 510A Dimensions (mm).
NANO-PV -D510A User Manual Page 5 1.5 Dat a Flow 6 Figure 1-4 shows the data flow between the system chipset, the CPU an d other components installed on th e motherboa rd. Figure 1-4: Data Flow Diagram 1.6 T echnical S pecifications NANO-PV-D510A technical spec ifications are listed in 6 Table 1-1 .
NANO-PV -D510A User Manual Page 6 Specification NANO-PV-D510 A Memory One single-channel 2.0 GB (max.) 667/ 800 MHz DDR2 SDRAM SO-DIMM supported Audio Realtek ALC888 HD codec LAN Intel® GbE PHY W8 2567V and PCIe GbE W82583V Super I/O Controller Fintek F81865 BIOS AMI BIOS Watchdog Timer Software programm able supports 1 ~255 sec.
NANO-PV -D510A User Manual Page 7 Specification NANO-PV-D510 A Environmental and Power Specifications Power Supply 12 V only , A T/A TX support by jumper Power Consumption 12 V @ 1.
NANO-PV -D510A User Manual Page 8 Chapter 2 2 Unpacking.
NANO-PV -D510A User Manual Page 9 2.1 Anti-st atic Precautions W ARNING! Static electricity can destroy certain el ectronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user.
NANO-PV -D510A User Manual Page 10 2.3 Packing List NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Cont act the IEI reseller or vendo r the NANO-PV-D510A was purchased from or contact an IEI sales representative directly by sending an em ail to 32 sales@iei.
NANO-PV -D510A User Manual Page 1 1 1 Utility CD 1 Quick Installa tion Guide 2.3.1 Optional Items The NANO-PV-D510A is shippe d with the followi ng components: Item and Part Number Image SA T A cable .
NANO-PV -D510A User Manual Page 12 Chapter 3 3 Connectors.
NANO-PV -D510A User Manual Page 13 3.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 Layout The figures below show all the conn ectors and jumpers. Figure 3-1: Connectors and Jumpers Figure 3-2: Connectors and Jumpers (Solder Side) 3.
NANO-PV -D510A User Manual Page 14 Connector Typ e Label +12 V A TX power supply connector 4-pin A TX connector CPU12V1 Audio connector 10-pin header AUDIO1 Battery connector 2-pin header BA T1 Compa .
NANO-PV -D510A User Manual Page 15 Connector Typ e Label Ethernet connector RJ-45 LAN1, LAN2 Keyboard/Mouse connector PS/2 PT1 RS-232 serial port conne ctor 9-pin male COM1 USB port, dual USB port USB6_7 VGA port connector 15-pin female VGA1 Table 3-2: Rear Panel Connectors 3.
NANO-PV -D510A User Manual Page 16 Pin Description 3 EXT_12VIN 4 EXT_12VIN Table 3-3: AT Power Connector Pinouts 3.2.2 Audio Kit Connector CN Label: AUDIO1 CN Type: 10-pin header CN Location: See Figure 3-4 CN Pinouts: See Ta b l e 3 - 4 This connector co nne cts to an external audio kit.
NANO-PV -D510A User Manual Page 17 3.2.3 Battery Connector CN Label: BAT1 CN Type: 2-pin wafer (1x2) CN Location: See Figure 3-5 CN Pinouts: See Ta b l e 3 - 5 This is connected to the system battery. The battery p rovides power to the syste m clock to retain the time when power is turned off.
NANO-PV -D510A User Manual Page 18 Figure 3-6: CompactFlash® Slot Location Pin Description Pin Description 1 GROUND 26 VCC- IN CHECK1 2 DA T A 3 27 DA T A 11 3 DA T A 4 28 DA T A 12 4 DA T A 5 29 DA .
NANO-PV -D510A User Manual Page 19 Pin Description Pin Description 23 DA T A 2 48 DA T A 9 24 N/C 49 DA T A 10 25 VCC- IN CHECK2 50 GROUND Table 3-6: CompactFlash® Slot Pinouts 3.
NANO-PV -D510A User Manual Page 20 3.2.6 Fan Connector CN Label: CPU_FAN1, SYS_FAN1 CN Type: 3-pin header CN Location: See Figure 3-8 CN Pinouts: See Ta b l e 3 - 8 The fan connector attaches to a cooling fan. Figure 3-8: Fan Connector Location Pin Description 1 GND 2 +12V 3 F ANIO1 Table 3-8: Fan Connector Pinouts 3.
NANO-PV -D510A User Manual Page 21 The front panel connector connects to the indicator LEDs and buttons o n the computer's front panel. Figure 3-9: Front Panel Connector Pinout Locations (8-pin) .
NANO-PV -D510A User Manual Page 22 Figure 3-10: Backlight Inverter Conn ector L ocation Pin Description 1 BACKLIGHT ADJUST 2 GROUND 3 +12 V 4 GROUND 5 BACKLIGHT ENABLE Table 3-10: Backlight Inverter Conn ector Pinou ts 3.
NANO-PV -D510A User Manual Page 23 Pin Description 1 +5 V KB DA T A 2 MS DA T A 3 MS CLK 4 KB DA T A 5 KB CLK 6 GROUND Table 3-11: Keyboard/Mouse Connector Pinouts 3.
NANO-PV -D510A User Manual Page 24 Pin Description Pin Description 13 GROUND 14 GROUND 15 LDDC_DA T A 16 LDDC_CLK 17 VCC_LCD 18 VCC_LCD 19 VCC_LCD 20 VCC_LCD Table 3-12: LVDS Connector Pinouts 3.
NANO-PV -D510A User Manual Page 25 Pin Description Pin Description 19 GROUND 20 GROUND 21 GROUND 22 GROUND 23 GROUND 24 GROUND 25 GROUND 26 NC Table 3-13: Parallel Port Connector Pinouts 3.
NANO-PV -D510A User Manual Page 26 Pin Row A Row B Row C Row D 9 SERR# GND SB0# PAR 10 GND PERR# +3.3 V SDONE 11 STOP# +3.3 V LOCK# GND 12 +3.3 V TRDY# GND DEVS EL# 13 FRAME# GND IRDY# +3.3 V 14 GND AD16 +3.3 V C/BE2# 15 AD18 +3.3 V AD17 GND 16 AD21 AD20 GND AD19 17 +3.
NANO-PV -D510A User Manual Page 27 Figure 3-15: PCIe Mini Card Slot Location Pin Description Pin Description 1 PCIE_WAKE# 2 VCC3 3 N/C 4 GND 5 N/C 6 1.5 V 7 CLKREQ# 8 LFRAME# 9 GND 10 LAD3 11 CLK - 12 LAD2 13 CLK+ 14 LAD1 15 GND 16 LAD0 17 PCIRST# 18 GND 19 LPC 20 VCC3 21 GND 22 PCIRST# 23 PERN2 24 3 VDual 25 PERP2 26 GND 27 GND 28 1.
NANO-PV -D510A User Manual Page 28 Pin Description Pin Description 47 SA T A_TXP1 48 1.5 V 49 GND 50 GND 51 N/C 52 VCC3 Table 3-15: PCIe Mini Card Slot Pinouts 3.
NANO-PV -D510A User Manual Page 29 3.2.15 SA T A Power Connector CN Label: PWR1 CN Type: 2-pin header CN Location: See Figure 3-17 CN Pinouts: See T able 3-17 Use the SATA Power Connector to connect to SATA device powe r con nections.
NANO-PV -D510A User Manual Page 30 Figure 3-18: Serial Port Connector Locations Pin Description Pin Description 1 Data Carrier Direct (DCD) 2 Data Set Ready (DSR) 3 Rece ive Data (RXD) 4 Reque st T o .
NANO-PV -D510A User Manual Page 31 Pin Description Pin Description 1 DCD 2 NDSR2 3 RXD 4 NR TS2 5 TXD 6 NCTS2 7 DT R 8 NRI2 9 GND 10 GND 11 TXD485+ 12 TXD485- 13 RXD485+ 14 RXD485- Table 3-19: Serial Port Connector Pinouts 3.
NANO-PV -D510A User Manual Page 32 3.2.19 USB Connector CN Label: USB0_1, USB2_3 and USB4_ 5 CN Type: 8-pin header (2x4) CN Location: See Figure 3-21 CN Pinouts: See T able 3-21 The USB connectors conn ect to USB device s . Each pin header provides two USB ports.
NANO-PV -D510A User Manual Page 33 Figure 3-22: External Peripheral Interface Co nnector 3.3.1 Keyboard/Mouse Connector CN Label: PT1 CN Type: PS/2 CN Location: See Figure 3-22 CN Pinouts: See T able 3-22 The keyboard and mouse conne ctor i s a standard PS/2 connector.
NANO-PV -D510A User Manual Page 34 3.3.2 LAN Connector CN Label: LAN1 CN Type: RJ-45 CN Location: See Figure 3-24 CN Pinouts: See T able 3-23 A 10/100/1000 Mb/s connection can be made to a Local Area Net work.
NANO-PV -D510A User Manual Page 35 3.3.3 Serial Port Connectors (COM1) CN Label: COM1 CN Type: DB-9 c onnecto r CN Location: See Figure 3-22 CN Pinouts: See T able 3-25 and Figure 3-25 The serial port connects to a RS-2 32 serial communications device.
NANO-PV -D510A User Manual Page 36 Pin Description Pin Description 1 USBV3L 5 V 2 GND 3 USBP4N 4 USBP5P 5 USBP4P 6 USBP5N 7 GND 8 USBV3L 5 V Table 3-26: USB Port Pinouts 3.
NANO-PV -D510A User Manual Page 37 Chapter 4 4 Installation.
NANO-PV -D510A User Manual Page 38 4.1 Anti-st atic Precautions W ARNING: Failure to take ESD precautions during the installation of the NANO-PV-D510A may result in permanent damage to the NANO-PV-D510A and severe injury to the user. Electrostatic discharge (E SD) can cause se rious damage to electronic com ponents, including the NANO-PV-D510A.
NANO-PV -D510A User Manual Page 39 W ARNING: The installation instru ctions described in this manual should be carefully followed in order to prevent damage to the components and injury to the user.
NANO-PV -D510A User Manual Page 40 4.3 Memory Inst allation W ARNING: Do not run the CPU without a heatsi n k and fan. Without the heatsink and fan, the high temperatures ca n destroy the CPU and other components. CPUs marked as fanless don't need the fan, but still need adequate ventilation.
NANO-PV -D510A User Manual Page 41 Figure 4-1: CompactFlash® Card Installation 4.3.2 PCIe Mini Card Inst allation To install the PCIe Mini card, please refer to the diagram and instru ction s below.
NANO-PV -D510A User Manual Page 42 Step 4: Insert into the socket at a nd angle . Lin e up the notch on the card with the notch on the connector . Slide the PCIe Mini card into the socket at an angle of about 20º. Step 5: Push down until the card clip s into place .
NANO-PV -D510A User Manual Page 43 Description Label Type A T/A TX power select J_AUT OPWR1 2-pin header A T/A TX power select J_A TXCTL1 3-pin header CompactFla sh® ca rd setup JCF1 3-pin header Cle.
NANO-PV -D510A User Manual Page 44 4.4.2 A T/A TX Power Select Jumper Settings Jumper Label: J_ATXCTL1 Jumper Type: 3-pin h eader Jumper Settings: See Ta b l e 4 - 2 Jumper Location: See Figure 4-3 The AT Power Select jump er specifies the syst e ms power mode a s A T or A T X .
NANO-PV -D510A User Manual Page 45 Figure 4-5: Clear BIOS Jumper Location 4.4.4 COM 3 Function Select Jumper Jumper Label: J1 Jumper Type: 3-pin h eader Jumper Settings: See T able 4-5 Jumper Location.
NANO-PV -D510A User Manual Page 46 The CompactFlash ® slot is connected through an IDE conne ction. This jumper sets the CompactFlash® card as the master or sl ave IDE device. Setting Descri ption Open Slave Closed Master Table 4-6: CompactFlash® Setup Jumper Settings Figure 4-7: CompactFlash® Setup Jumper Location 4.
NANO-PV -D510A User Manual Page 47 Setting Descri ption 1-2 +3.3 V 3-4 +5.0 V 5-6 +12 V Table 4-7: LVDS Voltage Selection Jumper Settings Figure 4-8: LVDS Voltage Selection Jumper Locat ions 4.
NANO-PV -D510A User Manual Page 48 Pin Description Open 640 x 480 (18-bit) Short 1-2 800 x 480 (18-bit) Short 3-4 800 x 600 (18-bit) Short 1-2 and 3-4 1024 x 600 (18-bit ) Short 5-6 1024 x 768 (18-bit.
NANO-PV -D510A User Manual Page 49 Figure 4-10: PCI-104 Voltage Jumper Location 4.5 Chassis Inst allation 4.5.1 Airflow W ARNING: Airflow is critical for keeping components wit hin recommended operating temperatures. The chassis sho uld have fans and vents as necessary to keep things cool.
NANO-PV -D510A User Manual Page 50 4.6.1 A T/A TX Power Connection Follow the instructions below to conn ect the NANO-PV-D510A to an AT or A TX power supply. W ARNING: Disconnect the powe r supply power co rd from its A C power source to prevent a sudden power surge to the NA NO-PV-D510A.
NANO-PV -D510A User Manual Page 51 Step 3: Connect Power Cable to Po wer Supply . Connect o ne of the 4-pin (1x4) M olex type power cable connectors to an A T/A TX power supply . See Figure 4-12. Step 3: Figure 4-12: Connect Power Cable to Power Supply 4.
NANO-PV -D510A User Manual Page 52 Step 5: Align pin 1 . Align pin 1 on the on-board connecto r with pin 1 on the audio kit connector. Pin 1 on the audio cable connecto r is indi cated with a white dot. See Figure 4-13. Figure 4-13: Audio Cable Connection Connect the audio dev ices .
NANO-PV -D510A User Manual Page 53 Step 6: Locate the connector . The location of the keyboard/mouse Y -cable connector is shown in Chapter 3 . Step 7: Align the connectors . Correctly align pin 1 on the cable con nector with pin 1 on the NANO-PV -D510A keyboard/mouse connector .
NANO-PV -D510A User Manual Page 54 PS/2 connectors. The keyboard PS/2 connector an d mouse PS/2 con nector are both marked. Please make sure the keyboard and mo use a re connected to the correct PS/2 connector.
NANO-PV -D510A User Manual Page 55 Step 4: Connect the serial device . Once the single RS-23 2 connector is connected to a chassis or bracket, a serial communi cations device can be connected to the system.
NANO-PV -D510A User Manual Page 56 Figure 4-16: LAN Connection Step 3: Insert the LAN cable RJ-45 connector . Once aligned, gently inse rt the LAN cable RJ-45 connector into the onbo ard RJ-45 connector . Step 0: 4.7.2 PS/2 Y -Ca ble Connection The NANO-PV-D510A ha s a PS/2 connector on the external peripheral interfa ce panel.
NANO-PV -D510A User Manual Page 57 Figure 4-17: PS/2 Keyboard/Mouse Connec tor Step 3: Connect the key board and mouse . Connect the keyboard and mouse to the appropriate connector . The keyboard and mouse connect ors can be distinguished from each ot her by looking at the small graphic at the top of the connecto r .
NANO-PV -D510A User Manual Page 58 Figure 4-18: Serial Device Connector Step 3: Secure the connector . Secure the serial device conn ector to the e xternal interface by tightening the two retention screws o n either side of th e connector . Step 0: 4.
NANO-PV -D510A User Manual Page 59 Figure 4-19: USB Connector 4.7.5 VGA Monitor Connection The NANO-PV-D510A has a single fem ale DB-15 connector on the external periphe ral interface panel. The DB-15 connect or is connected to a CRT or VGA monitor. To connect a monitor to the NANO-PV-D510A, plea se follow the instructions below.
NANO-PV -D510A User Manual Page 60 Figure 4-20: VGA Connector Step 6: Secure the connector . Secure the DB-15 VGA connector from the VGA monitor to the external interface by tight ening the two retention screws on either side of the connector . Step 0: 4.
NANO-PV -D510A User Manual Page 61 Figure 4-21: Introduction Screen Step 3: Click NANO-P V - D510A. Step 4: A new screen with a list of available drivers appears ( Figure 4-22). Figure 4-22: Available Driv ers Step 5: Install all of the necessary drivers in this menu.
NANO-PV -D510A User Manual Page 62 Chapter 5 5 BIOS.
NANO-PV -D510A User Manual Page 63 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BI OS setup program allows changes to certain system settings. This chapter o u tlines the op t ions that ca n be changed. 5.1.1 St arting Setup The AMI BIOS is activated when the comput er i s turned on.
NANO-PV -D510A User Manual Page 64 Key Function F2 /F3 key Change color from tot al 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 5-1: BIOS Navigation Key s 5.
NANO-PV -D510A User Manual Page 65 5.2 Main The Main BIOS menu ( BI OS Menu 1 ) appears wh en the BIOS Setup p rogram is entered. The Main menu gives an overview of the basi c sy stem information.
NANO-PV -D510A User Manual Page 66 The System Overview field also has two user co nfig urable fields: System T ime [xx:xx:xx] Use the System Time option to set the system time. Manually e nter the hours, minutes and seconds. System Date [xx/xx/x x] Use the System Date option to set the system date.
NANO-PV -D510A User Manual Page 67 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯.
NANO-PV -D510A User Manual Page 68 Frequency: List s the CPU processing speed FSB S peed: Lists the FSB speed Cache L1: List s the CP U L1 cache size Cache L2: List s the CP U L2 cache size 5.
NANO-PV -D510A User Manual Page 69 Enhanced D EF AUL T Configures the on-board ATA/IDE controller to be in Enhanced mode. In this mode, IDE channel s and SATA channels are sepa rated. This mode supports up to 6 storage devices. Some legacy OS do n ot support this mode.
NANO-PV -D510A User Manual Page 70 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Primary IDE Master ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Device :Not Detected Type [Auto] LBA/Large Mode [Auto] Block (Multi-Sector Transfer) [Auto] PIO Mode [Auto] DMA Mode [Auto] S.
NANO-PV -D510A User Manual Page 71 32Bit Data T ransfer: Enables 32-bit dat a transfer . T ype [Auto] Use the Type BIOS option select the type of devic e the AMIBIOS attempts to boot from after the Power-On Self-T est (POST) is complete. Not Inst alled BIOS is prevented from searching for an IDE disk drive on the specified channel.
NANO-PV -D510A User Manual Page 72 Block (Multi Sector T ransfer) [Auto] Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect if the device suppo rt s mult i- sector transfe rs. Disabled BIOS is prevented from using Multi-Sector T ransfer on the specified channel.
NANO-PV -D510A User Manual Page 73 Auto D EF A UL T BIOS auto detects the DMA mode. Use this value if the IDE disk drive support cannot be determined. SWDMA0 Single W ord DMA mode 0 selected with a maximum data transfer rate of 2.1 MB/s SWDMA1 Single W ord DMA mode 1 selected with a maximum data transfer rate of 4.
NANO-PV -D510A User Manual Page 74 S.M.A.R.T [Auto] Use the S.M.A.R.T option to auto-dete ct, disable or enable Self-Monitoring Analysis and Reporting Technology (SMART) on t he drive on the specified chan nel. S.M.A.R.T predict s impending drive failures.
NANO-PV -D510A User Manual Page 75 Serial Port1 Address [3F8] Use the Serial Port1 Address option to select the Serial Port 1 base address. Disabled No base address is assi gn ed to Serial Por.
NANO-PV -D510A User Manual Page 76 Serial Port3 Address [2F8] Use the Serial Port3 Address option to select the Serial Port 3 base address. Disabled No base address is assi gn ed to Serial Por.
NANO-PV -D510A User Manual Page 77 Parallel Port Address [Disabled] Use the Parallel Port Address option to select the parallel port base ad dre ss.
NANO-PV -D510A User Manual Page 78 EPP+ECP The parallel port operates in the extended capabilities port (ECP) mode. The ECP mode support s bi-directional communication b etween the system and the .
NANO-PV -D510A User Manual Page 79 5.3.4 Hardware Heal th Configuration The Hardware Health Configura tion menu ( BIOS Menu 7 ) shows the operating temperature, fan speeds and system voltages.
NANO-PV -D510A User Manual Page 80 Auto Fan by RPM D EFA UL T The fan adjusts it s sp eed using these set tings by RPM: CPU T emp. Highest Limit CPU T emp.
NANO-PV -D510A User Manual Page 81 NOTE: PWM functions are supported only when using a 4-pin fan. When using a 3-pin fan, the PWM functions are not supp orted. CPU T emp. Highest Limit [05 0] W ARNING: CPU failure can result if this value is set too high The fan will turn off if the temperature falls below this value.
NANO-PV -D510A User Manual Page 82 When the fan is off, it will only start wh en the temperature exceeds this setting. Minimum V alue: 0°C Maximum V alue: 127°C CPU T emp.
NANO-PV -D510A User Manual Page 83 CPU Fan Fourth Setting [06 0] This value is always full speed and co rresponds to the CPU Temp. Fourth Limit. Minimum V alue: 0 (Auto Fan by Du tyCycle) o r 12 (Auto Fan by RPM) Maximum V alue: 100 CPU Fan Lowest Setting [050 ] This value is always full speed and co rresponds to the CPU Temp.
NANO-PV -D510A User Manual Page 84 allows a remote host ru nning a terminal program to displ ay and configure the BIOS settings. BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Conf.
NANO-PV -D510A User Manual Page 85 Serial Port Number [COM1] Use the Serial Port Number option to select the serial port used for rem ote access. COM1 D EF AUL T System is remotely accessed th.
NANO-PV -D510A User Manual Page 86 Boot Loader Redirection is active during POST and during Boot Loader Al w ays D EF AUL T Redirection is alway s active (Some OSes may not work if set to Always) T erminal T ype [ANSI] Use the Terminal Type BIOS option to specify the remote terminal type.
NANO-PV -D510A User Manual Page 87 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit Select AT/ATX Power [BY HARDWARE] Current Jumper Setting [ATX Power] > Power Configuratio.
NANO-PV -D510A User Manual Page 88 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit ACPI Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯.
NANO-PV -D510A User Manual Page 89 Resume on Keyboard/Mouse [Disabl ed] Use the Resume on Keyboard/Mouse BIOS option to enabl e activity on either the keyboard or mouse to rouse the system from a suspe nd or standby state. That is, the system is roused when the mouse i s moved or a button on the keyboard is pressed.
NANO-PV -D510A User Manual Page 90 Disabled D EF AUL T The real time clock (RTC) cannot gene rate a wake event Enabled If selected, the following appears with values that can be selected: RTC Alarm Date (Days) RTC Alarm Ti me After setting the ala rm, the computer turns itself on from a suspend st ate when the alarm goes of f.
NANO-PV -D510A User Manual Page 91 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit AHCI Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯.
NANO-PV -D510A User Manual Page 92 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit AHCI Port0 ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Device :Not Detected ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ SATA Port0 [Auto] S.
NANO-PV -D510A User Manual Page 93 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit USB Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Module Version – 2.24.5-13.4 USB Devices Enabled: None USB Functions [Enabled] USB 2.
NANO-PV -D510A User Manual Page 94 Disabled USB 2.0 controller disabled Enabled D EF AUL T USB 2.0 controlle r ena bled Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to en able USB mouse and USB keyboard support.
NANO-PV -D510A User Manual Page 95 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit USB Mass Storage Device Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ USB Mass Storage Reset Delay [20 Sec] Device #1 M-SysT5 Dell Memory Key 5.
NANO-PV -D510A User Manual Page 96 Auto D EF A UL T BIOS auto-detects the current USB. Floppy The USB device will be emulated as a floppy drive. The device can be either A: or B: resp onding to INT13h calls that return DL = 0 or DL = 1 respectively .
NANO-PV -D510A User Manual Page 97 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced PCI/PnP Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯.
NANO-PV -D510A User Manual Page 98 IRQ9 IRQ10 IRQ 1 1 IRQ 14 IRQ 15 DMA Channel# [A vailable] Use the DMA Channel# option to assign a specific DMA channel to a pa rticular PCI/PnP device.
NANO-PV -D510A User Manual Page 99 5.5 Boot Use the Boot menu ( BIOS Menu 16 ) to configure system boot options. BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Boot Settings ⎯⎯.
NANO-PV -D510A User Manual Page 100 Quick Boot [Enabled] Use the Quick Boot BIOS option to make the comp uter speed up the boot process. Disabled No POST procedures are skipp ed Enabled D .
NANO-PV -D510A User Manual Page 101 Bootup Num-Lock [On ] Use the Bootup Num-Lock BIOS option to specify if the number lock setting must b e modified during boot up.
NANO-PV -D510A User Manual Page 102 5.5.2 Boot Device Priority Use the Boot Dev ice Priority menu ( BIOS Menu 18 ) to specify the boot sequence from the available devices. The drive sequence also de pends on the boot sequen ce in the individual device section.
NANO-PV -D510A User Manual Page 103 5.5.3 Hard Disk Drives Use the Hard Disk Driv es menu to specify the boot sequence of the available HDDs. Only installed hard drives are shown.
NANO-PV -D510A User Manual Page 104 5.5.4 Removable Drives Use the Remov able Drives menu ( BIOS Menu 20 ) t o specify the boot sequence of the removable drives.
NANO-PV -D510A User Manual Page 105 The boot sequence from the available device s is selected. If the “ 1st Drive ” option is selected a list of available CD/ DVD drives is shown. Select the f irst CD/DVD drive the system boots from. If the “ 1st Drive ” is not used for booting this option may be disabled.
NANO-PV -D510A User Manual Page 106 Change Supervisor Password Use the Change Supervisor Pass word to set or change a supervisor password. The default for this option is Not Installed . If a superviso r password must be installed, sel ect this field and enter the password .
NANO-PV -D510A User Manual Page 107 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced Chipset Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below section may cause system to malfunction.
NANO-PV -D510A User Manual Page 108 Initiate Graphic Adapter Use the Initiate Graphic Adap ter option to select the graphi cs controller used as the primary boot device. Select either an integrate d graphics controlle r (IGD) or a combinatio n of PCI graphics cont roller, a PCI express ( PEG) controller or an IGD.
NANO-PV -D510A User Manual Page 109 5.7.2 Southbridge Configuration Use the Southbridge Configuration menu ( BIOS Menu 25 ) to configure the Southbridg e chipset.
NANO-PV -D510A User Manual Page 1 10 5.8 Exit Use the Exit menu ( BIOS Menu 26 ) to load default BIOS values, optimal failsaf e values and to save configuration changes.
NANO-PV -D510A User Manual P a g e 111 Load Failsafe Default s Use the Load Failsafe Defaults option to load failsafe default values for each of the parameters on the Setup menus.
NANO-PV -D510A User Manual Page 1 12 Appendix A A BIOS Options.
NANO-PV -D510A User Manual Page 1 13 Below is a list of BIOS configuration options in the BI OS cha pter. System Overview ................................................................................................................ . 65 System Time [xx:xx:xx] .
NANO-PV -D510A User Manual Page 1 14 CPU Fan Fourth Setting [060] ............................................................................................. 83 CPU Fan Lowest Setting [050] ...................................................
NANO-PV -D510A User Manual Page 1 15 AddOn ROM Display Mo de [Force BIOS] ....................................................................... 100 Bootup Num- Lock [On] .......................................................................
NANO-PV -D510A User Manual Page 1 16 Appendix B B One Key Recovery.
NANO-PV -D510A User Manual Page 1 17 B.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use fr ont end for the Norton Ghost syste m backup and recovery tool. The one key recovery provides quick and easy shortcut s for creating a backup and reverting to that backup or for re verting to the factory default settings.
NANO-PV -D510A User Manual Page 1 18 o Windows 7 o Windows CE 5.0 o Windows CE 6.0 o Windows XP Embedded Linux o Fedora Core 12 (Constanti ne) o Fedora Core 11 (Leonidas) o Fedora Core 10 (Cambridge) o Fedora Core 8 (Werewolf) o Fedora Core 7 (Moonshine) o RedHat RHEL-5.
NANO-PV -D510A User Manual Page 1 19 NOTE: The recovery CD can only be used with IEI products. The software will fail to run and a warning message will appear when use d on non-IEI hardwa re. B.2 Setup Procedure for Windows Prior to using the recovery tool to backup or restore system, a few setup procedures are required.
NANO-PV -D510A User Manual Page 120 NOTE: The setup procedures describe d below are for Microsoft Windows operating system users. For Lin ux system, most setup procedures are the same with Microsoft Windows except for several steps whi ch is described in Section B.
NANO-PV -D510A User Manual Page 121 Figure B-1: Recovery Tool Setup Me nu Step 5: Press < 5 > then <Enter>. Figure B-2: Command Mode Step 6: The command prompt win dow a ppears. T ype the following comm and s (marked in red) to create two partitions.
NANO-PV -D510A User Manual Page 122 Figure B-3: Partition Creation Commands.
NANO-PV -D510A User Manual Page 123 NOTE: Use the following commands to check if the partitions were created successfully . Step 7: Press any key to exit the recovery t ool and automatically reboot the system. Please continue to the following procedu re: Build-u p Recove ry Partition.
NANO-PV -D510A User Manual Page 124 Step 2: S tart the system. Step 3: Press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be p a tient. Step 4: When the recovery tool setup menu app ears, pre ss < 2 > then <Enter>.
NANO-PV -D510A User Manual Page 125 Step 6: After completing the syste m configuration, press any key in the following windo w to reboot the system. Figure B-6: Press any key to continue Step 7: Eject the recovery CD.
NANO-PV -D510A User Manual Page 126 Figure B-8: Recovery Tool Menu Step 3: The About Symantec Ghos t window appears. Click OK button to continue. Figure B-9: About Sy mantec G host Window Step 4: Use mouse to navigate to the option shown below ( Figure B-10 ).
NANO-PV -D510A User Manual Page 127 Figure B-10: Symantec Ghost Pa th Step 5: Select the local source drive as shown in Figure B-1 1 . Then click OK. Figure B-11: Select a Local Source Driv e Step 6: Select a source partition from basi c d rive as sho wn in Figure B-12 .
NANO-PV -D510A User Manual Page 128 Step 7: Select 1.2: [Recovery] NTFS driv e and enter a file name called iei ( Figure B-13 ). Click Sav e . The factory default image will then be saved in the selected recovery drive and named IEI.GHO. W ARNING: The file name of the factory default image must be iei.
NANO-PV -D510A User Manual Page 129 Step 8: When the Compress Image scree n in Figure B-14 prompts, clic k High to make the image file smaller . Figure B-14: Compress Image Step 9: The Proceed with partition image cre ation window appears, click Ye s to continue.
NANO-PV -D510A User Manual Page 130 Step 11: When the image creation completes, a screen prompt s as shown in Figure B-17 . Click Continue and close the Gho st window to exit the program. Figure B-17: Image Creation Complete Step 12: The recovery tool main menu window is shown as below .
NANO-PV -D510A User Manual Page 131 NOTE: If the Linux OS is not installed with GRUB (v0.97 or earlier) and Ext3, the Symantec Ghost may not function properly. While installi n g Linux OS, please create two partitions: Partition 1: / Partition 2: SW AP NOTE: Please reserve enough space for partition 3 for saving recovery images.
NANO-PV -D510A User Manual Page 132 system32> format N: /fs:nt fs /q /v:Recovery /y system32> exit Step 4: Build-up recovery p artition . Press any key to boot from the re covery CD. It will take a while t o laun ch the recovery tool. Please be patient.
NANO-PV -D510A User Manual Page 133 Step 7: The recovery tool menu appears. ( Figure B-22 ) Figure B-22: Recovery Tool Menu Step 8: Create a factory default image . Follow Ste p 2 ~ St ep 1 2 described in Section B.2.5 to create a factory default image.
NANO-PV -D510A User Manual Page 134 Figure B-23: Recovery Tool Main Menu The recovery tool has several functio ns including: 1. Factory Restore : Restore the factory default image (iei.GHO ) crea ted in Section B.2.5 . 2. Bac kup system : Create a system backup image (iei_ user .
NANO-PV -D510A User Manual Page 135 B.4.1 Factory Restore To restore the factory default image, please follow the steps b elow. Step 9: T ype < 1 > and press < Enter > in the main menu. Step 10: The Symantec Ghost window appears and sta rt s to restore the fa ctory default.
NANO-PV -D510A User Manual Page 136 B.4.2 Backup System To backup the system, please follow the steps belo w. Step 12: T ype < 2 > and press < Enter > in the main menu. Step 13: The Symantec Ghost window appears and sta rts to backup the system.
NANO-PV -D510A User Manual Page 137 B.4.3 Restore Y our Last Backup To restore the last system backu p, please follo w the steps below. Step 15: T ype < 3 > and press < Enter > in the main menu. Step 16: The Symantec Ghost window appears and st arts to restore th e last backup image (iei_user .
NANO-PV -D510A User Manual Page 138 B.4.4 Manual To restore the last system backu p, please follo w the steps below. Step 18: T ype < 4 > and press < Enter > in the main menu. Step 19: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually .
NANO-PV -D510A User Manual Page 139 Appendix C C Terminology.
NANO-PV -D510A User Manual Page 140 AC ’97 Audio Codec 97 (AC’97) refers to a codec st andard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (A CPI) is an OS-directed configuration, power management, and t hermal management interface.
NANO-PV -D510A User Manual Page 141 DMA Direct Memory Access (DMA) enabl es some peripheral device s to bypass the system processor and communi cate directly with the system memory . DIMM Dual Inline Memory Modules are a type of RAM that of fer a 64-bit data bus and have sep arate electrical cont acts on each sid e of the module.
NANO-PV -D510A User Manual Page 142 LCD Liquid cryst al display (LCD) is a flat, low-power display device that consists of two polarizin g p lates with a liquid crystal p anel in between.
NANO-PV -D510A User Manual Page 143 Appendix D D Digital I/O Interface.
NANO-PV -D510A User Manual Page 144 D.1 Introduction The DIO connector on th e NANO-PV-D510A is in terfaced to GPIO ports on the Super I/O chipset. The DIO has b oth 4-bit digital inputs and 4-bit digital out puts.
NANO-PV -D510A User Manual Page 145 D.3 Assembly Language Samples D.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the di gital I/O. An assembly program to enable digital I/O input functions is listed below. MOV AX, 6F08H Sets the digit al port as input INT 15H Initiates the INT 15H BIOS call D.
NANO-PV -D510A User Manual Page 146 Appendix E E Watchdog Timer.
NANO-PV -D510A User Manual Page 147 NOTE: The following discussi on applies to DOS. Conta ct IEI support or visit the IEI website for drivers for other operatin g sy stems. The Watchdog Timer is a hard ware-based timer that at tempts to restart the syste m when it stops working.
NANO-PV -D510A User Manual Page 148 NOTE: The Watchdog Timer is activated throug h software. The software application that activates the Watchdog Timer mu st also deactivate it when closed. If the Watchdog Timer i s not deactivated, the system will automatically restart after the Ti mer has finishe d its countdown.
NANO-PV -D510A User Manual Page 149 Appendix F F Compatibility.
NANO-PV -D510A User Manual Page 150 NOTE: The compatible items described here ha ve been tested by the IEI R&D team and found to be compatible with the NANO-PV-D510A F.1 Comp atible Operating Systems The following operating sy stems have been su ccessfully run on the NANO-PV-D510A.
NANO-PV -D510A User Manual Page 151 F.2 Comp atible Memory Modules NOTE: The memory modules listed below have been tested on the NANO-PV-D510A other memory m odules that comply with the specifications may also work on the NANO-PV-D510A but have not been tested.
NANO-PV -D510A User Manual Page 152 Appendix G G Hazardous Materials Disclosure.
NANO-PV -D510A User Manual Page 153 G.1 Hazardous Materials Disclosure T able for IPB Product s Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the produ ct is compliant with the Peoples Republic of Chin a (China) RoHS standards.
NANO-PV -D510A User Manual Page 154 Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (CR(VI)) Polybrominated Biphenyls (PBB) Polybrominated .
NANO-PV -D510A User Manual Page 155 此附件旨在确保本产品符合中国 RoHS 标准。以 下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的 限量要求。 .
An important point after buying a device Dialogue Tech NANO-PV-D510A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dialogue Tech NANO-PV-D510A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dialogue Tech NANO-PV-D510A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dialogue Tech NANO-PV-D510A you will learn all the available features of the product, as well as information on its operation. The information that you get Dialogue Tech NANO-PV-D510A will certainly help you make a decision on the purchase.
If you already are a holder of Dialogue Tech NANO-PV-D510A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dialogue Tech NANO-PV-D510A.
However, one of the most important roles played by the user manual is to help in solving problems with Dialogue Tech NANO-PV-D510A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dialogue Tech NANO-PV-D510A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
