Instruction/ maintenance manual of the product Rhodeus-LC LX800 PC/104 Diamond Systems
Go to page of 57
GF Rhodeus -LC Low Pow er AM D Geode™ LX800 PC/104 CPU Module with CRT/L CD, LAN and CF User’s Manu al Copy right 2008 Diamond Sy stems Corporation 1255 Terra Bella Ave.
- i - Index T able of Contents Chapter 1 - Introduction ....................................................1 1.1 Copyright Notice ............................................................. 2 1.2 About User ’ s Manual ............................
- ii - Index COM1/ COM2: Serial Port Connector ....................20 CFD1: CompactFlash II Socket ..............................21 2.3 The Installation Paths of CD Driver ......................... 22 Chapter 3 - BIOS .................................
- 1 - - 1 - Introduction 1 Chapter 1 Introduction Chapter 1 - Introduction.
- 2 - Introduction 1.1 Copyright Notice All Rights Reserved. The information in this document is subject to change without prior notice in order to improve the reliability , design and function. It does not represent a commitment on the part of the manufacturer .
- 3 - Introduction 1.4 Replacing the lithium battery Incorrect replacement of the lithium battery may lead to a risk of explosion. The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer . Do not throw lithium batteries into the trashcan.
- 4 - Introduction 1.6 W arranty This product is warranted to be in good working order for a period of two years from the date of purchase. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms.
- 5 - Introduct i on 1.7 Packing List If any of the above i tems i s damaged or m i ss i ng, contact your vendor i mmed i ately . 1.8 Ordering Information Rhodeus -LC PC/104 CPU module w i th AMD Geod.
- 6 - Introduction 6SHFL¿FDWLRQ Form Factor PC/104 CPU module Processor AMD Geode™ LX800 Cache 64K L1 cache and 128K L2 cache Chipset AMD LX800 + CS5536 System Memory 1 x 200 pins DDR SO-DIMM up to 1GB SDRAM VGA/ LCD Controller AMD Geode LX series CPU integrated VGA controller with 2D Engine (Shared memory Max.
- 7 - Introduction 1.10 Board Dimensions Unit:mm.
- 8 - Introduction Unit:mm.
- 9 - Installation 2 Chapter 2 Installation Chapter 2 - Installation.
- 10 - Installation 2.1 Block Diagrams 1 x 200pin SO-DIMM Socket PCI LAN Controller LAN RJ-45 Analog R.G.B. TTL 18/24 bit VGA LCD AMD Geode LX800 CPU 500MHz Memory Bus USB I/F IDE ATA I/F 1 x IDE 4 x .
- 1 1 - Installation 2.2 Jumpers and Connectors 10 9 1 2 JBA T1 13 COM1 17 KBM1 1 LAN1 2 IDE1 3 COM2 18 LCD1 16 LPT1 14 FDD1 12 USB1 1 1 VGA1 10 IR1 9 PWR1 4 JFRT1 8 LLED1 7 JRS1 6 PC/104 5 CON1 15 10.
- 12 - Installation Label Function JRS1 COM2 RS-232/422/485 Select JBA T1 CMOS Jumper Settings Jumper / Connector Quick Reference Jumpers DIMM1 200 pins DDR SDRAM DIMM Socket PC104_1 PC/104 for ISA In.
- 13 - Installation KBM1: Keyboard & Mouse Connector (1) Connector type: 2.0mm pitch 1x6 pins wafer connector Pin Description 1 KB_DA T A 2 GND 3 MS_DA T A 4 KB_CLK 5 KB_VCC 6 MS_CLK 1 LAN1: Fast Ethernet Connector (2) Pin Description Pin Description 1 TX+ 2 TX- 3 RX+ 4 N/C 5 N/C 6 RX- 7 N/C 8 N/C 9 GND 10 N/C (Key) 10 9 1 2 Connector type: 2.
- 14 - Installation PWR1: Power Supply Connector (4) Pin Description 1 +5V 2 GND 3 GND 4 +12V 1 IDE1: 44 pins IDE Connector (3) Pin Description Pin Description 1 IDE RESET 2 GND 3 DA T A7 4 DA T A8 5 .
- 15 - Installation PC/104: PC/104 ISA Interface (5) A 1 B 1 A 3 2 B 3 2 D 19 C 19 D 0 C 0 Pin Description Pin Description Pin Description Pin Description D0 GND C0 GND A1 IOCHCK# B1 GND D1 MEMCS16# C.
- 16 - Installation JFRT1: Switches and Indicators (8) It provides connectors for system indicators that provides light indication of the computer activities and switches to change the computer status.
- 17 - Installation USB1 supports two USB 2.0 w/ 480MB/s by pin header Pin Description Pin Description 1 +5V 2 +5V 3 USBD- 4 USBD- 5 USBD+ 6 USBD+ 7 GND 8 GND 9 GND 10 N/C (Key) USB1: USB Connector (1.
- 18 - Installation FDD1: 20 pins FDD Connector (12) Pin Description Pin Description 1 GND 2 Drive density Select 0 3 GND 4 N/C (Key) 5 GND 6 Drive Density Select 1 7 Write Data# 8 Index# 9 Write Gate.
- 19 - Installation CON1: RS-422/ 485 Output Connector (15) Pin RS-422 RS-485 1 TX+ Data+ 2 TX- Data- 3 RX+ N/C 4 RX- N/C 1 1 LPT1: 20 pins Parallel Port Connector (14) Pin Description Pin Description.
- 20 - Installation LCD1: TTL LCD Connector (16) Pin Description Pin Description 2 5V_SAFE 1 5V_SAFE 4 GND 3 GND 6 3V_SAFE 5 3V_SAFE 8 GND 7 N/C 10 PD1 9 PD0 12 PD3 1 1 PD2 14 PD5 13 PD4 16 PD7 15 PD6.
- 21 - Installation CFD1: CompactFlash II Socket CFD1 does not support hot swap. 'HIDXOWHGE¿UVW,'(6ODYH 2 5 5 0 2 6 1 Pin Description Pin Description 1 PDD3 26 GND 2 PDD4 27 .
- 22 - Installation 2.3 The Installation Paths of CD Driver Driver Path CHIPSET ChisetAMDLX ISA ISAITE8888 LAN EthernetREAL TEK8100C VGA GraphicsAMDLX.
- 23 - BIOS 3 Chapter 3 BIOS Chapter 3 - BIOS.
- 24 - BIOS The Award BIOS provides a Setup utility program for specifying the system FRQ¿JXUDWLRQVDQGVHWWLQJV7KH%,26520RIWKHVVWHPVWRUHVWKH6HWXS utility . When you turn on the computer , the Award BIOS is immediately activated.
- 25 - BIOS 3.3 Standard CMOS Features “Standard CMOS Features” allows you to record some basic hardware FRQ¿JXUDWLRQVLQRXUFRPSXWHUVVWHPDQGVHWWKHVVWHPFORFNDQG error handling. If the CPU card is already installed in a working system, you will not need to select this option.
- 26 - BIOS IDE Primary HDDs / IDE Secondary HDDs The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices. (DFKFKDQQHOFDQVXSSRUWXSWRWZRKDUGGLVNVWKH¿UVWLVWKH³0DVWHU´DQG the second is the “Slave”.
- 27 - BIOS Halt On 7KLV¿HOGGHWHUPLQHVZKHWKHURUQRWWKHVVWHPZLOOKDOWLIDQHUURULV detected during power up. All errors (default) Whenever the BIOS detects a non-fatal error , the system will stop and you will be prompted.
- 28 - BIOS 3.4 Advanced BIOS Features Quick Power On Self T est :KHQHQDEOHGWKLV¿HOGVSHHGVXSWKH3RZHU2Q6HOI7 HVW3267DIWHU the system is turned on. If it is set to Enabled, BIOS will skip some items. Setting: Enabled (Default), Disabled.
- 29 - BIOS Boot Up NumLock Status It allows you to activate the NumLock function after you power up the system. Setting: On (Default), Off. Security Option It allows you to limit access to the System and Setup. When you select System, the system prompts for the User Password every time you boot up.
- 30 - BIOS 3.5 Advanced Chipset Features CAS Latency Time It allows CAS latency time in HCLKs as 2 or 2.5. The system board designer VKRXOGVHWWKHYDOXHVLQWKLV¿HOGGHSHQGLQJR.
- 31 - BIOS Video Memory Size In order to determine how much memory is allocated to the video graphics device. Setting: None, 8M (Default), 16M, 32M, 64M, 128M, 254M. XOR MB0 Setting: Disabled (Default), Enabled. XOR Bit Select Setting: 18 (Default), 19, 20, 21.
- 32 - BIOS On-Chip IDE Channel 1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately . Setting: Disabled, Enabled (Default). OnChip IDE Devicev >>> 3.
- 33 - BIOS IDE Primary Master/Slave PIO It allows your system HDD controller to run faster . Rather than having the BIOS issue with a series of commands that transferring to or from the disk drive, PIO (Programmed Input/Output) allows the BIOS to communicate with the controller and CPU directly .
- 34 - BIOS SuperIO Device >>> Serial/ Onboard Parallel Port It allows you to select the onboard serial and parallel ports with their addresses. Setting: Serial Port 1 3F8/IRQ4 (Default) Serial Port 2 2F8/IRQ3 (Default) Parallel Port 378H/IRQ7 (Default) UART Mode Select It determines the UART 2 mode in your computer .
- 35 - BIOS Parallel Port Mode Setting: SPP (Default) EPP ECP ECP+EPP Normal EPP Mode Select Setting: EPP1.9, EPP1.7 (Default) ECP Mode Use DMA Setting: 1, 3 (Default). UR2 Duplex Mode Setting: Full, Half (Default). Use IR Pins Setting: RxD2,TxD2 , IR-Rx2Tx2 (Default).
- 36 - BIOS IT8888 ISA Decode IO >>> It allows you to use the IT8888 ISA Decode IO menu to set the IO memory range for the onboard ISA. Decode I/O Space 0/ 1/ 2/ 3/ 4/ 5 It allows you to allocate system resources to the ISA bridge and to enable the function correctly .
- 37 - BIOS IT8888 ISA Decode Memory >>> It allows you to use the IT8888 ISA Decode Memory to set the resources for the onboard ISA bus. Decode Memory Space 0/ 1/ 2/ 3 It allows you to allocate memory resources to the ISA bridge and to enable the function correctly .
- 38 - BIOS Decode Memory Speed 0/ 1/ 2/ 3 It allows you to specify the memory speed of the ISA bus. Setting: Subtractive Speed, Slow Speed, Medium Speed, Fast Speed. Decode Memory Addr . 0/ 1/ 2/ 3 [23: It allows you to allocate a memory address to the ISA bus.
- 39 - BIOS 5HVHW&RQ¿JXUDWLRQ'DWD ,WDOORZVRXWRGHWHUPLQHZKHWKHUWRUHVHWWKHFRQ¿JXUDWLRQGDWDRUQRW Setting: Disabled (Default), Enabled.
- 40 - BIOS IRQ Resources ,WDOORZVRXWRFRQ¿JXUHWKH,54'0$ 5HVRXUFHV PCI/VGA Palette Snoop Some non-standard VGA display cards may not show colors properly . It allows you to set whether or not MPEG ISA/VESA VGA cards can display with PCI/VGA.
- 41 - BIOS 3.8 PC Health Status Current CPU T emperature CPU/ MEM VCore VCC3/ +5V/ +12V/ VBA T(V)/ 5VSB.
- 42 - BIOS 3.9 Load Optimized Defaults ,WDOORZVRXWRORDGWKHGHIDXOWYDOXHVWRRXUVVWHPFRQ¿JXUDWLRQ7KH default setting is optimal and enabled all high performance features.
- 43 - BIOS 3.10 Set Password Using Password to set a password that will be used exclusively on the system. T o specify a password, highlight the type you want and press <Enter>.
- 44 - BIOS 3.1 1 Save & Exit Setup T yping “Y”, you will quit the setup utility and save all the changes into the CMOS memory . T yping “N”, you will return to Setup utility .
- 45 - BIOS 7 SLQJ³<´ZLOOTXLWWKH6HWXSXWLOLWZLWKRXWVDYLQJWKHPRGL¿FDWLRQV T yping “N” will return you to Setup utility .
- 46 - BIOS 3.13 BIOS Beep Sound code list Address Device Description E000:0000h - F000:FFFFh System BIOS Area D000:2000h - D000:FFFFh Free space D000:0000h - D000:1FFFh LAN ROM C000:E000h - CF00:FFFFh Free space C000:0000h - C000:DFFFh VGA BIOS A000:0000h - B000:FFFFh VGA RAM 0000:0000h - 9000:FFFFh DOS 640K 3.
- 47 - BIOS CFh T est CMOS read/write functionality C0h Early chipset initialization: Disable shadow RAM, L2 cache (socket 7 and below), program basic chipset registers C1h Detect memory: Auto detecti.
- 48 - BIOS 20h Reserved 21h HPM initialization (notebook platform) 22h Reserved 23h Check validity of RTC value; Load CMOS settings into BIOS stack. If CMOS checksum fails, use default value instead; Prepare BIOS resource map for PCI & PnP use.
- 49 - BIOS 47h Initialize EISA slot 48h Reserved 49h Calculate total memory by testing the last double last word of each 64K page; Program writes allocation for AMD K5 CPU 4Ah Reserved 4Bh Reserved 4.
- 50 - BIOS 70h Reserved 71h Reserved 72h Reserved 73h (QWHU $ :')/$6+(;(LI $ :')/$6+(;(LVIRXQGLQÀRSSGLYH and AL T+F2 is pressed 74h Reserved 75h Detect and install all IDE devices: HDD, LS120, ZIP , CDROM.
- 51 - Appendix 4 Chapter 4 Appendix Chapter 4 - Appendix.
- 52 - Appendix Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.
- 53 - Appendix 000003F8 - 000003FF Communications Port 00000778 - 0000077B Printer Port 00000A79 - 00000A79 ISAPNP Read Data Port 00000D00 - 0000FFFF PCI Bus 0000FC00 - 0000FCFF Realtek RTL8139/810x .
- 54 - Appendix 4.4 Memory Address Map Address Device Description EE000000 - EEFFFFFF Standard Floppy Disk Controller EFFE8000 - EFFEBFFF AMD Win 2K/XP Graphics Driver EFFEC000 - EFFEFFFF AMD Win 2K/X.
An important point after buying a device Diamond Systems Rhodeus-LC LX800 PC/104 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Diamond Systems Rhodeus-LC LX800 PC/104 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Diamond Systems Rhodeus-LC LX800 PC/104 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Diamond Systems Rhodeus-LC LX800 PC/104 you will learn all the available features of the product, as well as information on its operation. The information that you get Diamond Systems Rhodeus-LC LX800 PC/104 will certainly help you make a decision on the purchase.
If you already are a holder of Diamond Systems Rhodeus-LC LX800 PC/104, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Diamond Systems Rhodeus-LC LX800 PC/104.
However, one of the most important roles played by the user manual is to help in solving problems with Diamond Systems Rhodeus-LC LX800 PC/104. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Diamond Systems Rhodeus-LC LX800 PC/104 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
