Instruction/ maintenance manual of the product Digital 3000 AS Elinchrom
Go to page of 16
Instructions for use Instructions for use Instructions for use Instructions for use Instructions for use POWER POWER POWER POWER POWER UNIVERSALITY UNIVERSALITY UNIVERSALITY UNIVERSALITY UNIVERSALITY TOTAL ASYMMETRY ASYMMETRY ASYMMETRY ASYMMETRY ASYMMETRY elinca sa switzerland www.
2 page Table of contents Table of contents Table of contents Table of contents Table of contents Safety notice 3 3 3 3 3 Control panel 4 4 4 4 4 Before you start 5 5 5 5 5 Technical data 6 6 6 6 6 Mai.
3 FLASH SYSTEMS STORE ELECTRICAL ENERGY IN CAPACITORS BY APPLYING HIGH VOLTAGE. FOR YOUR SAFETY, NEVER OPEN YOUR FLASHES. ONLY AN AUTHORISED SERVICE ENGINEER SHOULD OPEN OR ATTEMPT TO REPAIR THE UNITS.
4 1 . Mains inlet power socket 2. Mains fuse (16 AT, slow blow) 3. Charge speed selectors - slow charge - normal charge - fast charge 4. Mains switch 5. Photocell and IR-Receiver 6. Photocell on/off 7. Sync.-socket with security lock 8. Open flash with charge indicator 9.
5 1) Mains connection The unit is manufactured to run on 200-240 V, 50/60 Hz. Before connecting them for the first time, make sure that your mains supply and the rating set on the equipment (electrical specification plate) are compatible.
6 Display Ws f-stop Power 9 3000 (180.3) 1/1 8 1500 (128.3) 1/2 7 750 (90.3) 1/4 6 375 (64.3) 1/8 5 188 (45.3) 1/16 5** 95 (32.3) 1/32 with 2 lampheads 5*** 62 (22.7) 1/48 with 3 lampheads on mains 230 V- 50 Hz 1.8 - 10 s 0.8 - 4.5 s 0.7 - 3.5 s on mains 115 V- 60 Hz 2 - 11s 0.
7 Standard type 5 x 20 mm, 16 AT (tempered). Before exchanging a blown fuse, switch off the unit and remove mains cable. Depress and turn the fuse holder anti-clockwise 1/8th and remove it. If the new fuse blows immediately upon reconnection return the pack to an ELINCHROM service centre for a check-up.
8 N.B. For even less load on the power supply line use and jointly. The modelling lamps automatically extinguish when the generator is charging but illuminate when the charge cycle ends. When the indicator of the touch (12) is illuminated and will sound whenever a command has been accepted by the generator (useful when using the IR handset).
9 10. POWER INDICATOR «BLINKS» 8. TOT AL POWER 9. INDIVIDUAL POWER OUTPUT This display indicates the total power released through the lampheads. The variation is a single steps or if the touch is held it will run continuously. The first number indicates charges by full f-stop, the second number by 1/10 f-stop.
10 11. SWITCHABLE PHOTOCELL (SLAVE) 12. SYNCHRONISATION SOCKET 12. ACCESSORY SOCKET The Amphenol secure locking system with standard 5 m cable is retained. Longer cables may be used. N.B. Do not link ELINCHROM units by cable to other manufacturers sync outlets.
11 The modelling lamp will only function when the lamphead is switched on (note : there is an overheating control switch ON/OFF in the lamphead). - Simple ON/OFF with ON setting indicated.
12 14. LAMPHEADS ON/OFF 15. FUSES FOR LAMPHEADS 13. LAMPHEADS Important : When plugging in a lamphead connector, first push in the front part, then firmly press in the whole plug, the rear part being secured by the locking spring. Different modelling lamps require corresponding fuses.
13 16. PROTECTIVE PIREX DOME For use with standard halogen lamp GX 6.35 socket. Transparent, matt or yellow (400 ° K colour correction), can be fitted to all lampheads, except R heads (rectangular heads) for which clear or matt security filters are available.
14 18. LAMPHEAD COMPATIBILITY * 2000 Ws with MICRO series ** 3000 Ws with MICRO series MAXIMUM Compatible with : Digital 1500/3000 AS and MICRO AS ADAPTABLE 4000 Ws Digital S S4000 T4 T A4 A4 A Box Li.
15 Accessories overview Accessories overview Accessories overview Accessories overview Accessories overview Reflectors Reflectors Reflectors Reflectors Reflectors code code code code code Wide angle .
16 Visit our W eb site : www.elinchrom.com Elinca s.a E. Digital 3000 AS (73316) Printed in Switzerland.
An important point after buying a device Elinchrom Digital 3000 AS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Elinchrom Digital 3000 AS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Elinchrom Digital 3000 AS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Elinchrom Digital 3000 AS you will learn all the available features of the product, as well as information on its operation. The information that you get Elinchrom Digital 3000 AS will certainly help you make a decision on the purchase.
If you already are a holder of Elinchrom Digital 3000 AS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Elinchrom Digital 3000 AS.
However, one of the most important roles played by the user manual is to help in solving problems with Elinchrom Digital 3000 AS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Elinchrom Digital 3000 AS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
