Instruction/ maintenance manual of the product C2RPS-SYS Enterasys Networks
Go to page of 34
SecureS t ack C2 Redundant Power System C2RPS-SYS Inst allation Guide C2RPS-CHAS8 C2RPS-PSM Powe r 9033977-01 Caution: Do not use this product with SecureS t ack C2 PoE devices.
.
i Notice Enterasys Networks reserv es the right to make changes in specifica tions and other information contained in this document and its web site without prior notice.
ii Regulatory Compliance Information Federal Communications Commission (FCC) Notice This device com plies with Pa r t 15 of the FCC rules.
iii Electromagnetic Compatibility (EMC) This product complies with the following: 47 CF R Pa r t s 2 and 15, CSA C108.8, 89/336/EEC, EN 55022, EN 61000 ‐ 3 ‐ 2, EN 61000 ‐ 3 ‐ 3, EN 55024, AS/NZS CISPR 22, VCCI V ‐ 3.
iv Declaration of Conformity Application of Co uncil Directiv e(s): 89/336/EEC 73/23/EEC Manufacturer’s Na me: Enterasys Networks, Inc. Manufacturer ’ s Address: 50 Minuteman Road Andover, MA 01810 USA European Representativ e Address: Enterasys Networks, Ltd.
v Enterasys Networks, Inc. Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCL OSED PRODUCT , CAREFULL Y READ THIS LICENSE AGREEMENT . This document is an agreement (“ Agreement”) betwee n the end user (“Y ou”) and Enterasys Network s, Inc.
vi 3. APPLICABLE LAW. This Agreem ent shal l be interpreted and governed under the laws and in the state and federal cour ts of the Commonwealth of Massachusetts wit hout regard to its conflicts of laws provisions.
vii 8. AUDIT RIGHTS. You here by acknowl edge that the intellectual property rights associated with the Program are of critical value .
viii.
ix Contents About this Guide Using This Guide ............ ............. ................ ............. ................ ............. ................ ........... ............ ....... xi Structure of This Guide ................ ................ .....
x Figures 1-1 SecureStack C2RPS-CHAS8 (front view without PSMs) ........ ................ ............. ................ .. 1-2 1-2 SecureStack C2RPS-CHAS8 (rear view with eigh t PSMs) ........ ............. ............. ................ .. 1-2 1-3 C2RPS-PSM (front view) .
SecureStack C2 Installation Guide xi About this Guide This guide provides an ov erview , installati on and troubleshooting instructions, and specifications .
Using the SecureStack C2 Manual Set xii About this Guide Using the SecureS t ack C2 Manual Set Other manuals have been dev eloped for the SecureStack C2 non ‐ PoE switch devices that can be connected to the RPS for pow er redundancy .
Conventions Used in This Guide SecureStack C2 Installation Guide xiii Conventions Used in This Guide The following conventions are used in this guide: Note: Calls the reader ’s attention to any item of information that may be of special import ance.
Conventions Used in This Guide xiv About this Guide.
SecureStack C 2 Installation Guide 1-1 1 Introduction This chapter provides a functional overview of the Re dundant Pow e r System (RPS), which incl.
RPS Overview 1-2 Introduction C2RPS-CHAS8 Chassis The chassis is a an eight ‐ slot frame without AC power connections or electronics. The chassis can be installed in a standar d 19 ‐ inch rack and populated with up to eight PSMs.
RPS Overview SecureStack C 2 Installation Guide 1-3 C2RPS-PSM Power Supply Module The PSM provides the following: •H o t sw ap capability . •O n e 12 Vdc, 150 Wa t t s of maximum ‐ continuous power output to a connected SecureStack C2 switch device.
RPS Deployment Strategies 1-4 Introduction RPS Deployment St rategies The RPS can be deploy ed in a va r i e t y of situations with mission ‐ critical applications.
Getting Help SecureStack C 2 Installation Guide 1-5 Getting Help For additional support related to the devices or thi s document, contact Enterasys Netw.
Getting Help 1-6 Introduction.
SecureStack C 2 Installation Guide 2-1 2 Installation This chapter provides the installation instructions to install all the components of an RPS. To correctly install an RPS, follow the order of information listed below .
Installing C2RPS-PSMs 2-2 Installation 3. P erform a visual inspection of the switch devices for any signs of physical damage. Contact Enterasy s Netw orks if there are any sig ns of da mage .
Installing C2RPS-PSMs SecureStack C 2 Installation Guide 2-3 5. Proceed to “ Installing C2RPS ‐ CHAS8 into the Rack ” on page 2 ‐ 4 for the rack mount installation instructions.
Installing C2RPS-CHAS8 into the Rack 2-4 Installation 3. Pull the PSM out and remove it from the chassis. 4. Repeat steps 1 through 3 for each additional PSM yo u plan to remove.
Installing C2RPS-CHAS8 into the Rack SecureStack C 2 Installation Guide 2-5 •A n amb ient temperature of between 5 ° C (41 ° F) and 40 ° C (104 ° F) must .
Connecting the PSM Cables and AC Power Cords 2-6 Installation Figure 2-2 Fastening the C2RPS-CHAS8 to the Rack Connecting the PSM Cables and AC Power Cords The PSMs are connected to the SecureStack Ethernet switch devices using PSM cables.
Connecting the PSM Cables and AC Power Cords SecureStack C 2 Installation Guide 2-7 5. On certain switches, an LED indicator will show that a redundant pow er supply is now in operation. .
Connecting the PSM Cables and AC Power Cords 2-8 Installation Figure 2-5 C2RPS-PSM Cable and AC Power Cord Co nnections 1 Switch device 4 Switch device Redundant Power Sup ply connector 2 PSM cable 5 .
SecureStack C2 Installation Guide A-1 A Specifications This appendix provides information about the foll owing: Enterasys Netw orks reserves the right to change the specifications at any time without notice.
C2RPS-PSM Specifications A-2 Specifications C2RPS-PSM Specifications Refer to Ta b l e A ‐ 2 for the input/output port specifications.
Compliance Standards SecureStack C2 Installation Guide A-3 Compliance S t andards The C2RPS ‐ PSM meets the safety and electromagnetic compati bility (EMC) requir.
Compliance Standards A-4 Specifications.
An important point after buying a device Enterasys Networks C2RPS-SYS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Enterasys Networks C2RPS-SYS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Enterasys Networks C2RPS-SYS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Enterasys Networks C2RPS-SYS you will learn all the available features of the product, as well as information on its operation. The information that you get Enterasys Networks C2RPS-SYS will certainly help you make a decision on the purchase.
If you already are a holder of Enterasys Networks C2RPS-SYS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Enterasys Networks C2RPS-SYS.
However, one of the most important roles played by the user manual is to help in solving problems with Enterasys Networks C2RPS-SYS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Enterasys Networks C2RPS-SYS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
