Instruction/ maintenance manual of the product XONE:S2L Allen & Heath
Go to page of 32
Allen & Heath 1 XONE:S2 Use r Guide USER GUIDE Publication AP6858_3.
Allen & Heath 2 XONE:S2 Use r Guide Limited One Y ear W arranty This product is warranted to be free from defects in materials or workmanship for period of one year from the date of purchase by the original owner.
Allen & Heath 3 XONE:S 2 User Gui de P A CKED ITEMS Check that you have received the f ollowing: Safety Sheet Important ! R e a d t h i s s h e e t before starting. Retain for future reference. Registration Card Complete and return to Allen & Heath to register your product.
Allen & Heath 4 XONE:S 2 User Gui de CONTENTS Congratulations on purchasing the A llen & Heath Xone:S 2 performance DJ mixer. To ensure that you get the maximum benefit from the unit please spare a few minutes familiarizing yourself with the controls and setup procedures outlined in this user gu ide.
Allen & Heath 5 XONE:S 2 User Gui de P ANEL DRA WINGS TO PC USB LR Rear P anel F ront P anel The Xone: S2 can be ordered with either rotary or linear faders.
Allen & Heath 6 XONE:S 2 User Gui de INTR ODUCTION T O THE XONE:S2 The Xone:S2 is a 19” rack mounted 4U analogue DJ mixe r featuring four stereo du al input channels, two Mono Mic/Stereo Line channels, and is available with either 45mm linear, or rotary VCA faders.
Allen & Heath 7 XONE:S 2 User Gui de SPECIFICA TIONS Operating Levels Input RIAA input sensitivity 7-100mV 47K/330pF Line Inputs -10dB to +15dB RCA Mic Sensitivity -57 to –27dBu Balanced XLR USB.
Allen & Heath 8 XONE:S 2 User Gui de BLOCK DIA GRAM STER EO INPUTS R 1,2,3,4 3 BAND E Q RIAA PHONO/LINE LEVEL RIAA DISABLE MET ER VCA BL OCK D IAGR AM XONE:S2 LEVE L TRIM PHO NO L R LINE L + DC FA.
Allen & Heath 9 XONE:S 2 User Gui de MIC / LINE INPUT CHANNEL 1 2 3 4 5 1 Mic Input Socket Standard 3-Pin XLR socket wired as Pin 1 = Ground, Pin 2 = hot (+), Pin 3 = cold (-). 2 Mic / Line Select Switch Selects either the XLR micro phone input or the alterna- tive RCA stereo line input.
Allen & Heath 10 XONE:S 2 User MIC / LINE INPUT CHANNEL 7 8 7 Channel Fader 60mm smooth travel fader ad justs the channel signal level from fully off to fully on.
Allen & Heath 11 XONE:S 2 User PHONO / LINE INPUT CHANNEL 1 2 3 4 5 6 1 Phono / Line Select Switch Selects either the RCA phono inp ut or the alternative RCA stereo line input. In the up position PHONO is selected, when pressed LINE is selected. 2 Channel Level Control This control has a range of –10 to +4dB dependant upon the channel trim.
Allen & Heath 12 XONE:S 2 User PHONO / LINE INPUT CHANNEL 7 8 7 Channel Fader A high quality, 45mm smooth travel dual-rail fader or rotary potentiometer adjusts the channel signal level from fully off to fully on. 8 XFade Switch Used to assign the channel to either the X (left) or Y (right) side of the cross-fa der.
Allen & Heath 13 XONE:S 2 User FIL TER SECTION 1 2 3 4 5 1 Filter Assign Selector Selects the channel to be rout ed thr ough the filter. The FILTER LED in the selected channel section will light when selected. The EXTERNAL LED will light when the selector is set to EXTE RNAL.
Allen & Heath 14 XONE:S 2 User 6 7 FIL TER SECTION 6 Frequency Sweep Control This control sets the –3dB cut- off fr equency of the filter. It ranges from very low fre quency (20Hz) to very high frequency (20kHz). NOTE: Both BPF and HPF f ilters are band limited to prevent them going above 10kHz.
Allen & Heath 15 XONE:S 2 User USB / HEADPHONE SECTION 1 2 3 4 1 USB Connector USB (Universal Serial Bus) V1.1 is an external peripheral interface standard for data transmission. Xone:S2 USB works at 12Mbps and provides two stereo uncom- pressed audio channels.
Allen & Heath 16 XONE:S 2 User USB / HEADPHONE SECTION 6 7 6 Split Cue Switch Press the Split Cue Sw itch to activate split cue mode. In split cue mode the cue signal is fed to the left side of the headphones and is displayed on the left output meter.
Allen & Heath 17 XONE:S 2 User HEADPHONE CABLE CLIPS 1 1 1 Wire Clips Two wire clips are provided for the purpo se of securing the headphone cabling away from the front panel controls of the mixer. NOTE: A third headphone socket is availa ble on the rear o f the mixer.
Allen & Heath 18 XONE:S 2 User EXTERNAL INPUT / AUT O DUCK / EFFECT LOOP 1 2 4 5 1 External Input Sockets Front-panel mounted stereo RCA sockets for easy con- nection of external line level audio sources. 2 External Input Level Control The external input level control ranges from - ∞ to +6dB based on the input level.
Allen & Heath 19 XONE:S 2 User 6 7 6 Ducker Active LED Lights when the main o utputs are being ducked. Also lights when the external alarm input switch closure is active. 7 Effect Loop Switch Switches in the FX insert circuit. The LED indicator around the switch lights when selected.
Allen & Heath 20 XONE:S 2 User MASTER SECTION 1 2 3 4 5 1 Mix / Monitor Meters The main meters follow the selected monitor source. The default display is the po st master level, which is overridden with an input channe l level if the channel cue switch is selected.
Allen & Heath 21 XONE:S 2 User 6 Monitor Mono Switch Sums the left and right signal levels to produce a mono mix from both outputs. 7 Balance Control Use to compensate for poor signal balance between left and right or as a panning effe ct. The balance control is disabled if the outputs are set to mono.
Allen & Heath 22 XONE:S 2 User CR OSSF ADER 1 2 3 1 Crossfader Curve Control This control adjusts the crossfader cu rve between dipped response, ideal for seamless beat mixing, and fast-attack, su itable for scratch or cut mixing . 2 Crossfader On Switch In its normal (out) position the crossfader is active.
Allen & Heath 23 XONE:S 2 User REAR CONNECT ORS 1 2 3 4 5 1 2 Mix Output Balanced XLR. This is th e main output that feeds the house PA system. Plug into the house processor/amplifier system using balanced cabl es. Use balanced cabl es a nd equipment.
Allen & Heath 24 XONE:S 2 User REAR CONNECT ORS 7 8 9 10 7 8 Headphone 3 Third headphone socket, stereo 1/4” TRS jack. Sound To Light A high impedance, ground isolated mono output designed to provide an audio feed for light- ing systems.
Allen & Heath 25 XONE:S 2 User REAR CONNECT ORS 11 12 13 11 12 Monitor Output RCA phono (–2dBu nominal). Provides a line le vel stereo feed to th e DJ local monitor am- plifier system. It is not affected by the master fader or cue system. FX Insert Point RCA phono.
Allen & Heath 26 XONE:S 2 User 16 Mic / Line Channel Line Input Stereo RCA Phono input for line source on Mic / Line channels. Co nnect stereo line level music sources such as CD, MD, DAT, drum ma chines, keyboards or other instruments. Do not connect turntables which require RIAA equalisation.
Allen & Heath 27 XONE:S 2 User REAR CONNECT ORS 19 20 AC Mains Input IEC cable with moulded mains plug suitable for your local supply. Important: Read the SAFETY INSTRUCTIONS sheet included with the Xone:S2 and printed on the rear panel. Check that the correct mains lead with moulde d plug has been supplied with your console.
Allen & Heath 28 XONE:S 2 User REAR CONNECT ORS - ZONE OUT 22 23 22 23 Zone Output Balanced TRS Jack outputs for se parate zone—nominal +4dBu. Th is output is ideal for feed- ing a separate room or bar area. Do not unbalance this output by shorting on e phase to ground.
Allen & Heath 29 XONE:S 2 User 26 Alarm Override Switch Input To interface to safety alarm systems , shorting these two connections together will mute th e four main music channels but leave the Mic channels open. The Duck L ED on the front panel also illuminates to show th at the alarm has been activated.
Allen & Heath 30 XONE:S 2 User USER LINK OPTIONS CAUTION: The following service instructions are for use by qualified personnel only. To reduce the risk of electric shock do not perform any servicing other than that described in the operating instruct ions unless you are qualified to do so.
Allen & Heath 31 XONE:S 2 User USER LINK OPTIONS Filter PCB Headphone PCB Remove JP1to disable the Filter On switch. To change the USB Audio input feed from the RCA sockets on the rear panel (default) to the internal left/right mix buss, move jumper links CN8 and CN9 from pins 2-3 to 1-2.
Allen & Heath 32 XONE:S 2 User REPLA CING THE CR OSSF ADER / F A CE PLA TE Replacing the Crossfader Use a medium size cross-point screwdriver to undo and remove the two outer screws on the crossfader plate. Do not remove the inner scre ws. Carefully pull the crossfader assembly away from the front panel.
An important point after buying a device Allen & Heath XONE:S2L (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Allen & Heath XONE:S2L yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Allen & Heath XONE:S2L - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Allen & Heath XONE:S2L you will learn all the available features of the product, as well as information on its operation. The information that you get Allen & Heath XONE:S2L will certainly help you make a decision on the purchase.
If you already are a holder of Allen & Heath XONE:S2L, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Allen & Heath XONE:S2L.
However, one of the most important roles played by the user manual is to help in solving problems with Allen & Heath XONE:S2L. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Allen & Heath XONE:S2L along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
