Instruction/ maintenance manual of the product PXA-H701 Alpine
Go to page of 48
EN FR ES R ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U.S.A. Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC.
.
1 -EN FR ES DE SE IT Contents Operating Instructions W ARNING W ARNING .................................................. 2 CAUTION ................................................... 2 PRECAUTIONS ......................................... 3 Basic Operation T urning the po wer on and of f .
2 -EN W ARNING WARNING This symbol means important instructions. F ailure to heed them can result in serious injur y or death. DO NOT OPERA TE ANY FUNCTION THA T T AKES YOUR A TTENTION AW A Y FROM SAFEL Y DRIVING YOUR VEHICLE. Any function that requires your prolonged attention should only be performed after coming to a complete stop.
3 -EN FR ES DE SE IT PRECAUTIONS T emperature Be sure the temperature inside the vehicle is between +60 ° C (+140 ° F) and –10 ° C (+14 ° F) before turning your unit on.
4 -EN About indicators • PRO LOGIC II indicator Lights amber in the Dolby Surround decode mode • Dolby Digital indicator Lights amber in the Dolby Digital decode mode • DTS indicator Lights amber in the DTS decode mode Operating the Rotary encoder This unit uses the Rotary encoder when establishing settings or adjustments.
5 -EN EN FR ES DE SE IT Adjusting the input level Using the analog, RCA-type connections, the PXA-H701 ’ s input lev el must be preset from the head unit. Adjust the input level using a sound source with a high recording le vel (such as pop or rock music).
6 -EN 3 Connect the microphone. 1) F asten the microphone included with control unit at the center of the driver ’ s seat ’ s headrest f acing upwards . 2) Connect the microphone to the PXA-H701. 4 Set the vehicle ’ s engine key to the A CC position.
7 -EN EN FR ES DE SE IT With the automatic adjustment function, the operation described below is perf or med. Adjustments are completed in about 10 seconds. Time correction. “ END ” is display ed for about 15 seconds and the automatic adjustment is completed.
8 -EN Performing time correction manually (TCR)/Switching the phase Because of the particular conditions inside the v ehicle, there are major diff erences in the distances between the diff erent speakers and the listening position.
9 -EN EN FR ES DE SE IT 9 T urn the Rotary encoder to s witch the phase, then press the CHANNEL button. Press the ENTER button to return to step 8. 0 180 10 Repeat steps 7 to 9 to adjust other channels. 11 Once the adjustments are completed, press the TCR/PHASE button.
10 -EN Settings/Adjustments Bass Focus The time diff erence between the front-rear/left- right speakers, can be adjusted a pair at a time . Audib le time correction can be made from 0.05 ms to 20.00 ms in 401 steps (0 to 400). 1 Check that the def eat mode is off.
11 -EN EN FR ES DE SE IT Example of Steps 4 and 5 Setting 1. After entering corrections for the front (left and right) speakers in STEP 30, the time diff erence is 1.5 ms for both front-left and front-right speakers. 2. After entering corrections for the left (front and rear) speakers in STEP 30, the time diff erence becomes 3.
12 -EN Settings/Adjustments (factory default) * 3 When center is set to subwoofer , it becomes Sub .W(R). 5 T urn the Rotary encoder to select the frequency , then press the ENTER button. Adjustable frequencies Front/Rear/Center: 20Hz~20kHz (1/3 octave step) Sub .
13 -EN EN FR ES DE SE IT Parametric equalizer adjustments The frequency bands of the graphic equaliz er are fix ed. This makes it v er y difficult to correct for undesired peaks and dips at specific frequencies. The parametric equalizer ’ s center frequency can be tuned these specific frequencies.
14 -EN NO TES • When the speaker is set to the “ OFF ” mode , the parametric equalizer for that speaker is inef fective. Refer to “ Setting the speakers ” (page 4). • It is not possible to adjust the fr equencies of adjacent bands within 7 steps.
15 -EN EN FR ES DE SE IT X-OVER The PXA-H701 is equipped with an activ e crossov er allowing the frequency bands to be split bef ore amplification. Because of this, there is no need f or a passive netw or k between the speakers and amplifiers . This mak es the amplifiers fully independent, eliminating the problem of interf erence.
16 -EN * 1 When center is set to subwoofer , it is not displa yed. * 2 When center is set to subwoofer , it becomes Sub .W(L). * 3 When center is set to subwoofer , it becomes Sub .W(R). 5 T urn the Rotary encoder to adjust the H.P .F . cutoff frequency , then press the ENTER button.
17 -EN EN FR ES DE SE IT Hint for adjusting the subwoofer • If the subwoof er is installed on the rear deck, setting a gentle L.P .F . slope (for e xample 6 dB/ oct.) makes the sound localization more to the rear . This can also affect the acoustic localization of the front.
18 -EN MX settings MX (Media Xpander) makes v ocals or instruments sound distinct regardless of the music source. The radio , CD , and MP3, will be able to reproduce the m usic clear ly e ven in cars with a lot of road noise.
19 -EN EN FR ES DE SE IT 3 T urn the Rotary encoder to select the source (media) you w ant to set, then press the ENTER button. 4 T urn the Rotary encoder to select the desired mode, then press the ENTER b utton. For further information about setting mode, see step 3 of 1 (page 18).
20 -EN * If DOLBY PL II MUSIC is selected, the center width can be adjusted with following operations. This function off ers the optimum vocal position by adjusting the center channel position between the center speaker and the L/R speaker .
21 -EN FR ES DE SE IT Adjustment procedure for Dolby Surround Make the adjustments described below in order to reproduce Dolby Digital and DTS sound with greater accuracy .
22 -EN Using Dolby Surr ound OFF: When no speaker is connected SMALL: When a speaker that cannot play low frequencies (80 Hz or less) is connected LARGE: When a speaker that can play low frequencies (80 Hz or less) is connected *1: It is not possible to set the front speakers to “ OFF ” .
23 -EN FR ES DE SE IT 4 T urn the Rotary encoder to select “ Auto ” , then press the ENTER button. T est tone output is repeated f or each of the different speaker channels. They will be repeated in the order shown below . If no operation is perf or med f or 2 seconds, the channel s witches to the ne xt channel.
24 -EN Using Dolby Surr ound Adjusting the acoustic image In most installations, the center speak er must be placed directly between the front passenger and driver . Using this function, the center channel inf or mation is distributed to the left and right speakers .
25 -EN FR ES DE SE IT Achieving powerful high volume sound With Dolby Digital, the dynamic r ange is compressed so that powerful sound can be achie v ed at regular volume le vels . This compression can be canceled to achieve an energetic sound with e ven greater pow er , like the sound in a movie theater .
26 -EN Convenient Functions Linear PCM setting The output when pla ying discs recorded in linear PCM can be set to 2 or 3 channels. 1 Press the SETUP button. The setup mode is set. 2 T urn the Rotary encoder to select the “ PCM MODE ” , then press the ENTER button.
27 -EN EN FR ES DE SE IT Display settings The displa y ’ s contrast and LCD (negativ e/ positiv e) can be adjusted. 1 Press the SETUP button. The setup mode is set. 2 T urn the Rotary encoder to select the “ DISPLA Y SETUP ” mode, then press the ENTER button.
28 -EN Convenient Functions Storing settings in the memory This function can store up to 6 adjustments/ settings. The f ollowing adjustments/settings are stored in a preset memory .
29 -EN EN FR ES DE SE IT Switching the display mode 1 Press the DISP button to select the desired display mode . IN P H TC P – 2 U L R Ls Rs F LE C P S Example of input channel (When monaural surround signal (s) is not inputted) The display changes according to the input signals.
30 -EN Installation and Connections Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use. W arning DO NOT DISASSEMBLE OR AL TER. Doing so may result in an accident, fire or electric shock.
31 -EN FR ES DE SE IT ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP MET AL EDGE. Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges.
32 -EN Installation and Connections IMPORT ANT Please record the serial number of your unit in the space provided below and keep it as a per manent record.
33 -EN FR ES DE SE IT Installation Mounting the control unit (Sold Separately) CAUTION: Do not install the control unit near the air-bag of the front passenger ’ s seat. • Confirm the installation location will be safe. • Deter mine the mounting position on the dashboard.
34 -EN Installation and Connections 3 Mount the spacer and brack et to the control unit. Next, securely mount the f actory brackets remov ed from the factory radio, to the control unit assembly .
35 -EN FR ES DE SE IT Mounting the base unit ● V elcro Fastener Mounting Attach to the vehicle (such as under the dashboard). Flanged self-tapping screw (M4 x 14) V elcro fastener ● Using the Mounting Screws (Supplied) The Base Unit can be mounted under the seat using the mounting screws .
36 -EN Installation and Connections Basic Connections Diagram Display (Sold Separately) Cord colors and cord/terminal specifications Connect to: • Front 1 speaker output jacks (RCA outputs) Outputs signals for driving the front 1 speakers. • Front 2 speaker output jacks (RCA outputs) Outputs signals for driving the front 2 speakers.
37 -EN FR ES DE SE IT Examples of system expansion Battery Blue/White Blue/White White/green Not used in this system Not used in this system To External Amplifier Remote ON Cable Connect to a metal part of chassis body with a screw.
38 -EN Installation and Connections NO TE Please observe the follo wing when using Fiber Optic Cable. • Do not coil the F iber Optic Cable smaller than a 30mm radius.
39 -EN FR ES DE SE IT • PXA-H701 + Head Unit + V ideo Deck etc. + External Amplifier • F or connecting a head unit with which Ai-NET connections are not possible. NO TE When using the PXA-H701 with a non-Ai-NET head unit, +12V is r equired on this line * to turn on the equalizer .
40 -EN Installation and Connections • PXA-H701 + IV A-D300 Head Unit + CD Changer + Navigation System + External Amplifier NO TE Also r efer to the operating instructions of the KCE-900E. F or details, contact your stor e of purc hase or an Alpine Information Center .
41 -EN EN FR ES DE SE IT Information T erminology Dolby Digital Dolby Digital is a digital audio compression technology de veloped b y Dolby Laboratories that allows large quantities of audio data to be efficiently recorded on discs. It is compatible with audio signals from mono (1 channel) all the wa y up to 5.
42 -EN In case of difficulty If you encounter a prob lem, please revie w the items in the f ollowing checklist. This guide will help you isolate the prob lem if the unit is at f ault. Otherwise , make sure the rest of y our system is proper ly connected or consult your authoriz ed Alpine dealer.
43 -EN EN FR ES DE SE IT Specifications Graphic EQ number of bands: Front (left and right) 31 bands Rear (left and right) 31 bands Center 31 bands Subwoofer 10 bands Graphic EQ boost cut range: ± 9 dB Parametric EQ number of bands: Front/rear/center 5 bands Subwoofer 2 bands Parametric EQ frequency: Front, Rear and Center Band 1: 20/22/25/28/31.
.
Fidèles à leur engagement de ne fournir que des produits de qualité, ALPINE ELECTRONIQUE DE L'AMERIQUE INC. et ALPINE ELECTRONIQUE DU CANADA INC. (Alpine) sont heureuses de vous offrir cette garantie. Nous vous suggérons de le lire attentivement et en entier.
ALPINE ELECTRONICS OF AMERICA, INC. AND ALPINE OF CANADA INC. ("Alpine"), are dedicated to quality craftsmanship and are pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any questions, please contact your Dealer or Alpine at one of the telephone numbers listed below.
An important point after buying a device Alpine PXA-H701 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Alpine PXA-H701 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Alpine PXA-H701 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Alpine PXA-H701 you will learn all the available features of the product, as well as information on its operation. The information that you get Alpine PXA-H701 will certainly help you make a decision on the purchase.
If you already are a holder of Alpine PXA-H701, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Alpine PXA-H701.
However, one of the most important roles played by the user manual is to help in solving problems with Alpine PXA-H701. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Alpine PXA-H701 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
