Instruction/ maintenance manual of the product L0523252 GE
Go to page of 12
Installation Instructions Built-In Dishwasher l If you have questions, call 800-GECARES or visit our website at: www.GEAppliances.com I BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT- Observe all governing codes and ordinances.
Installation Preparation PARTS SUPPLIED: [] Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package).
Installation Preparation PREPARE DISHWASHER ENCLOSURE 34" to 35" Underside of Countertop to Floor Max. Square and Plumb Figure A Floor MUST be Even with Plumbing and Electric Senlice Room Floor. Must EnterShaded Area • The rough cabinet opening must be at least 24" deep and 17-5/8" to 18" wide.
Installation Preparation PREPARE ELECTRICAL WIRING WARNING FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. Electrical Requirements • This appliance must be supplied with 120V, 60 Hz.
Installation Instructions PREPARE HOT WATER LINE • The line may enter from either side, rear or floor within the shaded area shown in Figure E • The line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" dia.
Installation Instructions I STEP 21ADJUST LEVELING LEGS • Move the dishwasher close to the installation location and lay it on its back. / Adjust to Installation Height Figure H • Measure installation height and dishwasher height. Extend leveling legs out from the dishwasher base, 1/4" less than installation height.
Installation Instructions I STEP 61 POSITION WATER LINE AND HOUSE WIRING • Position water supply line and house wiring on the floor of the opening to avoid interference with base of dishwasher and components under dishwasher.
Installation Instructions I STEP 91 POSITION DISHWASHER UNDER COUNTERTOP • Check to be surethatwires are secure under the dishwasher and not pinched or in contact with door springs or other dishwasher components. TIP: Check tub insulation blanket, if equipped.
Installation Instructions I STEP 111SECURE DISHWASHER TO CABINET The dishwasher must be secured to the countertop. • Position the dishwasher so that the tub flange aligns with the front face of the cabinet frame.
Installation Instructions I STEP 131 CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES. The drain hose molded end will fit 5/8", 3/4" or 1" diameter connections on the air gap, waste tee or disposer. Cuton the marked line as required for your installation.
Installation Instructions I STEP 141 CONNECT POWER SUPPLY Skip this step if equipped with power cord, Verify that power is turned off at the source. • Remove junction box cover "A". • Locate the three dishwasher wires, (white, black and green) with stripped ends.
Installation Instructions I STEP 161 DISHWASHER WET TEST [] Turn on power supply (or plug power cord into outlet, if equipped). [] Turn dial to Normal "Wash" position. [] Close door. [] Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, checkto be sure that water and power are turned on.
An important point after buying a device GE L0523252 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE L0523252 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE L0523252 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE L0523252 you will learn all the available features of the product, as well as information on its operation. The information that you get GE L0523252 will certainly help you make a decision on the purchase.
If you already are a holder of GE L0523252, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE L0523252.
However, one of the most important roles played by the user manual is to help in solving problems with GE L0523252. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE L0523252 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center