Instruction/ maintenance manual of the product PTDS650GMWT GE
Go to page of 9
W ARNING RISK OF FIRE • To r educe the risk of severe injury or death, follow all installation instructions. • Clothes dryer installation must be performed by a qualied installer . • Install the clothes dryer according to these instructions and in accordance with local codes.
Installation Instructions 2 Minimum Clearance Other Than Alcove or Closet Installation Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and 1 in. rear . Consideration must be given to provide adequate clearance for installation and service.
Installation Instructions 3 3 RECONNECTING GAS Note: The connector and ttings are designed for use only on the original installation and are not to be r eused for another appliance or at another location. Keep are end of adaptor free of gr ease, oil and thread sealant .
Installation Instructions 4 5 ELECTRICAL CONNECTION INFORMA TION ELECTRICAL REQUIREMENTS This appliance must be supplied with 120V , 60Hz, and connected to a properly gr ounded branch circuit , protected by a 15- or 20- amp cir cuit breaker or time- delay fuse.
Installation Instructions 5 7 EXHAUST C ONNECTION THIS DRYER COMES RE ADY FOR REAR EXHAUSTING. IF SP ACE IS LIMITED , USE THE INSTRUCTIONS IN SECTION 9 T O EXHAUST DIRECTL Y FROM THE SIDES OR BO T T OM OF THE CABINE T . RECOMMENDED CONFIGUR A TION TO MINIMIZE EXHAUST BLOCKAGE.
Installation Instructions 6 CONNECTING THE DRYER T O HOUSE VENT RIGID MET AL TRANSITION DUCT • For best drying performance, a rigid metal transition duct is recommended.
Installation Instructions 7 12 DRYER E XHA UST T O RIGHT , LEFT OR BO T T OM CABINE T W ARNING - BEFORE PERFORMING THIS EXHAUST INST ALL A TION, BE SURE T O DISCONNECT THE DRYER FROM ITS ELECTRICAL SUPPL Y . PROTECT Y OUR HANDS AND ARMS FROM SHARP EDGES WHEN WORKING INSIDE THE CABINE T .
Installation Instructions 8 PL A TE (KIT WE1M454) 13 CHANGING DIRECTION OF DOOR OPENING ADDING ELBOW FOR EXHAUST THROUGH BOT T OM OF CABINE T • Insert the elbow through the rear opening and connect it to the dryer internal duct . • Apply duct tape on the joint between the dryer internal duct and elbow , as shown on page 7.
Installation Instructions 9 WATER SUPPLY REQUIREMENTS Hot and cold water faucets MUST be installed within 42 in. (107 cm) of your washer ’s water inlet . The faucets MUST be 3/4 in. (1.9 cm) garden hose-type so inlet hoses can be connected. Water pressure MUST be between 10 and 120 pounds per square inch.
An important point after buying a device GE PTDS650GMWT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE PTDS650GMWT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE PTDS650GMWT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE PTDS650GMWT you will learn all the available features of the product, as well as information on its operation. The information that you get GE PTDS650GMWT will certainly help you make a decision on the purchase.
If you already are a holder of GE PTDS650GMWT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE PTDS650GMWT.
However, one of the most important roles played by the user manual is to help in solving problems with GE PTDS650GMWT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE PTDS650GMWT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
