Instruction/ maintenance manual of the product CD Changer Honda
Go to page of 10
© 2001 American Honda Motor Co., Inc - All Rights Reserved. AII 23268 (0110) 1 of 10 INST ALLA TION INSTRUCTIONS Accessory Application Publications No.
2 of 10 AII 23268 (0110) © 2001 American Honda Motor Co., Inc - All Rights Reserved. T OOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver Flat-tip screwdriver Stubby Phillips screwdriver 10 mm Combin.
© 2001 American Honda Motor Co., Inc - All Rights Reserved. AII 23268 (0110) 3 of 10 5. Remov e the self-tapping screws that f asten the radio , and pull the unit out toward y ou. Unplug the vehicle harness connector and the antenna lead from the rear of the radio .
4 of 10 AII 23268 (0110) © 2001 American Honda Motor Co., Inc - All Rights Reserved. 9. Remov e the f our e xpansion clips that f asten the floor carpet, and fold the carpet down and out of the wa y .
© 2001 American Honda Motor Co., Inc - All Rights Reserved. AII 23268 (0110) 5 of 10 14. Continue routing the BUS cable toward the rear of the vehicle. Measure 35 mm below the door opening, and secure the BUS cable to the body with f our cushion tapes.
6 of 10 AII 23268 (0110) © 2001 American Honda Motor Co., Inc - All Rights Reserved. 22. Remov e the three clips, and f old down the top por tion of the middle carpet. If the v ehicle y ou are working on is equipped with rear speakers, remove the speakers and rear speaker holders.
© 2001 American Honda Motor Co., Inc - All Rights Reserved. AII 23268 (0110) 7 of 10 Installing the CD Changer 26. Carefully unpack the CD changer . Remove the three shipping clips, and discard the shipping cov er . Sav e the shipping clips f or your customer in the e v ent the unit needs to be serviced.
8 of 10 AII 23268 (0110) © 2001 American Honda Motor Co., Inc - All Rights Reserved. 32. Place the CD changer trim on the CD changer , and install the f our self-tapping screws. 35. Remove the vehicle harness clip from the hole in the inner panel. 36.
© 2001 American Honda Motor Co., Inc - All Rights Reserved. AII 23268 (0110) 9 of 10 REAR BRACKET STUDS EPT SEALER EPT SEALER 6 x 16 mm W ASHER-BOL T FRONT BASE BRACKET REAR BASE BRACKET 6 x 16 mm W ASHER-BOL T EPT SEALER (Cut in half.) FRONT BRACKET STUDS FLANGE NUTS 38.
10 of 10 AII 23268 (0110) © 2001 American Honda Motor Co., Inc - All Rights Reserved. BUS CABLE Cut across. BASE BRACKET LONG WIRE TIE BUS CABLE CONNECTOR CD CHANGER BASE BRACKET CLIPS LEFT TRUNK SIDE BO ARD A B C BACK OF LEFT TRUNK SIDE BO ARD D CD CHANGER 135 mm 45.
An important point after buying a device Honda CD Changer (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Honda CD Changer yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Honda CD Changer - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Honda CD Changer you will learn all the available features of the product, as well as information on its operation. The information that you get Honda CD Changer will certainly help you make a decision on the purchase.
If you already are a holder of Honda CD Changer, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Honda CD Changer.
However, one of the most important roles played by the user manual is to help in solving problems with Honda CD Changer. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Honda CD Changer along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
