Instruction/ maintenance manual of the product BWM12 Hotpoint
Go to page of 24
Congratulations on the pur chase of your new built-in appliance. IMPORT ANT INFORMA TION Please read this Instruction Manual thoroughly before installing and using your appliance for the first time .
W ARNING: This appliance must be earthed. F uses Y our appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse , only those rated at 13A and AST A approv ed to BS1362 should be used. T o change the fuse in a moulded plug, lif t holder to v ertical position and lif t fuse out.
Electricity Supply ...................................... 2 Recycling & Disposal Information .............. 3 Installation Instructions ............ 3 i. Remove T ransit Bolts ....................... 4 ii. Choose a Location... ... 4 iii. Connect to the W ater Supply .
i. Remov e T ransit Screws... BEFORE A T TEMPTING T O USE THE MA CHINE, Y OU MUST FOLL OW THE PR OCEDURE DESCRIBED BEL OW. The inside of the appliance is supported, for transportation, by four screws on the back panel. Before using the appliance these MUST be remov ed.
iii. Connect to the W ater Supply ... ● W ater taps and standpipe should be situated a way from the rear of appliance but in easy access for turning on and off . ● F or your machine to operate c orrectly it requires water pressures in the r ange of 6-150 psi (100 - 1000KPa).
iv . Connect to a Dr ainage S ystem... ● Connect up the drain hose, af ter fitting the hooked end support supplied in the machine. ● Ensure the drainage hose is not obstructed, trapped or k inked .
v . F itting the Door P anel... ● The wooden panel that covers the fac e of the machine must not be less than 18mm in thickness and can be hinged on either side. F or practical reasons, it is advisable to maintain the same opening direction as the appliance door itself (hinges applied to the left hand side).
F itting the Door P anel and Plinth... Mounting parts onto the face of the appliance: - Mount the hinge supports onto the face of the machine, positioni ng the hole indicated by the arrow , in Fig.1, towards the inside of the face and using the type C screws .
Remember you may be charged for a service call if a problem with your appliance is caused b y incorrect installation or misuse. Inserting the machine into the cabinet:- - Push the machine into the opening , aligning it with the cabinet s (Fig .8). - Regulate the adjustable feet to r aise the machine to the appro priate height.
10 vii. L evelling ... Adjust the feet until all f our feet are in firm con tact with th e floor ensuring the appliance stands level in every direction.
11 The C ontrols The Contr ols W ARNINGS ● Do not allow children to play with the appliance or tamper with the controls. A . B . C . D. E . F . G . H .
Getting to K no w Y our Applianc e F unc tions - W ashing Machine Note: W e recommend on completion of your programme that you switch off the appliance by pressing the ‘ON/OFF’ . As a safety measure, switch off both the mains electricity and water supply to the appliance.
Getting to K no w Y our Applianc e F unc tions - W asher Dr yer Note: W e recommend on completion of your programme that you switch off the appliance by pressing the ‘ON/OFF’ . As a safety measure, switch off both the mains electricity and water supply to the appliance.
IMPORT ANT INFORMA TION: Always obser v e the laundry items wash car e label. Choosing a P rogr amme W e recommend the P ersil range of detergent pr oducts 14 Sort the laundr y according to the wash care labels and the degree of soiling. Close all zips and remove items from pockets.
IMPORT ANT INFORMA TION: Always obser v e the laundry items wash car e label. Choosing a P rogr amme W e recommend the P ersil range of detergent pr oducts 15 Sort the laundr y according to the wash care labels and the degree of soiling. Close all zips and remove items from pockets.
The Dispenser Dr aw er The dispenser dra wer is opened by rota ting outwards. Adding Detergent ● (1) Pre-wash tra y (powder) and (2) Main wash detergent tr ay (pow der or liquid) T o obtain the desi.
Using your applianc e 17 IMPORT ANT: - Do not open the door to stop the appliance . - Do not try to open the door while the Door Locked Indicator ligh t is lit. Setting a W ash Programme / Star ting the applianc e Load the laundry into the appliance and close the door .
How to dry ( W asher Dryer only). A Combined W ashing and drying pro gr amme See table below and follow instructions provided f or MAX load to have an aut omatic washing and drying c ycle . - Select the wash programme. - Select the programme wash temperature .
19 W ashing Before washing laundry :- ● Pre-trea t stains. ● Close zips, fasten belts, tie strings etc... and press studs to pr event tangling . ● Remove all items from pockets . ● Limit size of absorbent loads to give good w ashing/rinsing resu lts.
Cleaning the Exterior ... W ARNING ● Disconnect from the electricity supply before cleaning. ● Do not clean any par t of your appliance with abrasive cleaners , scouring agents, acids, chlorine based bleach or metal polish as they may cause damage.
My appliance does not work Check: ● water and pow er supplies and the fuse. ● if the door is closed properly . ● have y ou selected a delayed start? It will not load water Check: ● it is plugged in and switched on. ● if the door is closed properly .
22 A f t er Sales S er vic e “No compan y is better positioned to offer an after sales servic e on a Hotpoint appliance than us - the manufacturer” As part of our commitment to you , all Hotpoint appliances ha ve the added benefit of a fully inclusiv e par ts and labour guar antee for the first 12 mon ths.
23 Rec y cling & Disposal Inf ormation “Satisfaction guaranteed or y our money back” W e give y ou a unique ‘ satisfaction guaranteed’ promise - valid f or 90 da ys - after you ha ve purchased your Hotpoint applianc e. If there is a technical probl em simply call Hotpoint Repair ser vice or visit our w eb-site at www .
Repair Ser vic e and Information Desk UK: 08709 066 066 (Open 8 to 8 Mon - F ri, 8 to 6 Sat , 10 to 4 Sun & Bank Holidays) www .theservic ec en tr e .
An important point after buying a device Hotpoint BWM12 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hotpoint BWM12 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hotpoint BWM12 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hotpoint BWM12 you will learn all the available features of the product, as well as information on its operation. The information that you get Hotpoint BWM12 will certainly help you make a decision on the purchase.
If you already are a holder of Hotpoint BWM12, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hotpoint BWM12.
However, one of the most important roles played by the user manual is to help in solving problems with Hotpoint BWM12. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hotpoint BWM12 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
