Instruction/ maintenance manual of the product TI984 Hubbell Electric Heater Company
Go to page of 16
Pub.: 42004-071F GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA 610-777-1374 n 800-492-1212 n Fax: 610-775-6540 V ISIT WWW . GAI - TRONICS . COM FOR PRODUCT LITERATURE AND MANUALS GAI-TRONICS® CORPORATION A HUBBELL COMPANY Model TI984 Telephone Interface T ABLE OF C ONTENTS General Information .
42004-071F GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA 610-777-1374 n 800-492-1212 n Fax: 610-775-6540 V ISIT WWW . GAI - TRONICS .
P AGE 2 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 WARNING This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
P AGE 3 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 Recommendations: • Remove the Printed Circuit Board Assemblies (PCBAs) until installation of the conduit is complete.
P AGE 4 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 Figure 2 . Termination Area Telephone Line Connections The TI984 should be connected to the Central Office (CO) RJ11C jack from the telephone company or to a PBX with the 14-foot RJ11 interconnect cable.
P AGE 5 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 If using a dc source, either a battery and/or a UL-approved power supply/battery charger should be used. The power supply must be capable of providing at least 1.
P AGE 6 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 Terminals 7 and 8 are used for the remote A CCESS switch; terminals 9 and 10 are used for the remote R ESET switch; terminals 11 and 12 are used for the remote D AY / N IGHT switch.
P AGE 7 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 Programming Procedure Read the following instructions to determine which parameters are to be set, and which parameters remain at the factory setting (default setting).
P AGE 8 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 Programming Example: Night Mode Dial Sequence Description #*92 Put.
P AGE 9 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 If someone calls and discovers that the designated party line is busy, they can choose the voice access method to notify the person they are trying to reach to return their call.
P AGE 10 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 Terminating Calls Calls may be terminated in one of three ways: .
P AGE 11 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 Programming Table Function RESET UNIT TO FACTORY CODES (DEFAULT) .
P AGE 12 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 Programming Table *Function SELECT INCOMING CALL - SELECTIVE ACCE.
P AGE 13 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 Adjustments The inside front cover of the TI984 contains 3 potentiometers to adjust audio levels. Use a small standard screwdriver to adjust the page line level.
P AGE 14 of 14 M ODEL TI984 T ELEPHONE I NTERFACE 42004-071F f:standard ioms - current release42004 instr. manuals42004-071f.doc 05/03 Specifications FCC Registration Number .............................................................................
(Rev. 1/97) Wa rr anty Equipment . GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any GAI -Tronics equipment supplied hereunder shall be free of defects in material .
An important point after buying a device Hubbell Electric Heater Company TI984 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hubbell Electric Heater Company TI984 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hubbell Electric Heater Company TI984 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hubbell Electric Heater Company TI984 you will learn all the available features of the product, as well as information on its operation. The information that you get Hubbell Electric Heater Company TI984 will certainly help you make a decision on the purchase.
If you already are a holder of Hubbell Electric Heater Company TI984, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hubbell Electric Heater Company TI984.
However, one of the most important roles played by the user manual is to help in solving problems with Hubbell Electric Heater Company TI984. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hubbell Electric Heater Company TI984 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
