Instruction/ maintenance manual of the product Bath Ventilator Fan Hunter
Go to page of 16
2500 Frisco Avenue, Memphis, T ennessee 38114 Printed in China 41788-01 6/1/2005.
Installation Guide 82500 Infiniti™ Bath V entilator F an 41788-01 6/1/2005.
2 DISCONNECT ELECTRIC POWER SUPPL Y AND LOCK OUT SERVICE P ANEL BEFORE SERVICING UNIT W ARNING TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY , OBSERVE THE FOLLOWING: 1. For general ventilating use only. Do not use for ventilat- ing hazardous or explosive materials.
3 x4 3/8" Cable Connector * * * NO TE: Strain relief cable connector must be installed. Not Inc luded. A B C Extra Screws x2 H E D L 77864-02 F G H I J K 03242-07-133 96261-01-000 95047-02-000 74508-03-133 95776-01-000 75184-01-133 96258-01/02/03-008 75171-01/02/03-000 x2 Included.
A1 D Back out the pre-loaded screw tips until flush with the side of the housing. Remove the motor/blower from the housing. Remove the wiring cover screw . 4 Remove packing material. A2 A3 A6 F Loosen screw securing motor . A4 A 5 Remove the pre-loaded screw tip co vers.
A7 E A8 D A9 B C A 1 0 D 5/8 1/2 5/8 1/2 A 1 1 OPTION Remove the wiring cover . Pop out the first wiring access slug. Use second if needed. Insert the strain relief into the housing and secure with the washer . Position the correct depth mark at the bottom edge of the joist–based on the thickness of your sheet rock.
0 A 1 6 D A 1 2 A 1 3 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground A 1 4 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light T ogether *Option D E A 1 5 F Pull the wires through the strain relief.
A2 2 C1 Go to step on page 12 to attach grille . 0 0 0 0 D A 1 7 G 0 0 0 0 G D A 1 8 A2 0 O N O F F A 2 1 Connect wiring from the motor to the wiring cover plate. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing.
B3 7.25 ” 7.75 ” B1 D B2 Loosen screw securing motor . Remove the existing fan and check to make sure the opening is large enough to accommodate the new motor housing (7.25” x 7.75”) . Remove the motor/blower from the housing. Existing Construction Installation Existing F an 8 Remove packing material.
B4 B 5 B8 D B9 B C Back out the pre-loaded screw tips until flush with the side of the housing. 9 B 6 E B7 E Remo ve the wiring cover . Remove the wiring cover screw . Remove the pre-loaded screw tip co vers. 41788-01 6/1/2005 Insert the strain relief into the housing and secure with the washer .
D B 1 0 Fit housing into the opening and secure by tightening the pre-loaded screws into the joist. Note: Install the box flush with the sheetrock (ceiling). B 1 1 2 1 B 1 2 D B 1 3 D B 1 4 10 Pull the wires through the strain relief and tighten the strain relief screws.
D E F B 1 6 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground B 1 5 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light T ogether *Option D B 1 7 0 0 0 0 G D B 1 8 Install the wiring co ver plate.
B 2 0 O N O F F B 2 1 B 2 2 C1 Go to step to attach grille . 12 J C 1 T est the motor . If the motor does not run, check the plug connection. T urn on the power source. Attaching the Grille C 2 K L I 41788-01 6/1/2005 Remove the thumbscrews. Remove glass dome.
Connect wiring harness. I C 3 C 4 I Slide light mount over posts. Attach thumbscrews. WARNING: T o reduce the risk of electrical shock, all 3 thumbscrews MUST be properly installed. I J C 5 Install 2 Max 60 Watt A15 bulbs (Not Inc luded). C 6 Screw glass dome into position.
14 41788-01 6/1/2005 T rouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker.
W arranty Hunter Fan Company Bath Exhaust Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warr anty to the original user or consumer purchaser of this Hunter bath exhaust fan: If .
An important point after buying a device Hunter Bath Ventilator Fan (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter Bath Ventilator Fan yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter Bath Ventilator Fan - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter Bath Ventilator Fan you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter Bath Ventilator Fan will certainly help you make a decision on the purchase.
If you already are a holder of Hunter Bath Ventilator Fan, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter Bath Ventilator Fan.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter Bath Ventilator Fan. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter Bath Ventilator Fan along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
