Instruction/ maintenance manual of the product ZT 7102 Intel
Go to page of 152
Intel ® NetS tructure™ ZT 7102 Chassis Management Module Technical Product Specification August 20 04 Order N umber: 27 3770-017.
2 T echnical Product Spe cification Intel ® NetS tructure™ ZT 7102 Cha ssis Mana gement Mod ule INFORMA TION I N THIS DOCUMENT IS P ROVIDED IN CO NNECTION WITH INTEL ® PRODUCTS. NO LICENSE, EXPRESS O R IMPLIED, BY ESTO PPEL O R OTHERWI SE, TO ANY IN TEL LECTUAL PROPERTY RIGH TS I S GRANT ED BY THI S DOCUMENT .
T echnical Product Spe cificati on 3 Intel ® Ne tStructu re™ ZT 7102 Chass is Manage ment Module Con ten ts Contents 1.0 I ntrodu ction .............. ............. ................... .................... ................... ................... ..
4 T echnical Product Spe cification Intel ® NetS tructure™ ZT 7102 Cha ssis Mana gement Mod ule Content s 2.16 Telco Alar m Signa l................... ............. ................... ................... .................... ............. .. .....
T echnical Product Spe cificati on 5 Intel ® Ne tStructu re™ ZT 7102 Chass is Manage ment Module Con ten ts 6.7.3 CMM Failover ... .................... ............. ................... ................... .................... .......... 50 6.8 BIST Test Descr iptions .
6 T echnical Product Spe cification Intel ® NetS tructure™ ZT 7102 Cha ssis Mana gement Mod ule Content s 11.1.1 “health events” Quer y Event Syn tax ............ ................... .................... ................... . 67 11.1.2 SEL Even t Syntax .
T echnical Product Spe cificati on 7 Intel ® Ne tStructu re™ ZT 7102 Chass is Manage ment Module Con ten ts 15.3 Setting a Slot to A ctive Mode ................... ............. ................... .................... ................... .... 87 15.
8 T echnical Product Spe cification Intel ® NetS tructure™ ZT 7102 Cha ssis Mana gement Mod ule Content s 20.2.1 GetAuth Capability() .... ................... ............. ................... .................... .................. 1 04 20.2.2 ChassisM anagementA pi() .
T echnical Product Spe cificati on 9 Intel ® Ne tStructu re™ ZT 7102 Chass is Manage ment Module Con ten ts 25.12.2 Data Restore User Sc ript s. ... ...... ....... ...... ...... ....... ...... ....... ...... ....... ............. ...... .. 134 25.12.
10 T echnical Product Spe cification Intel ® NetS tructure™ ZT 7102 Cha ssis Mana gement Mod ule Content s 9 BIST Flo w Chart .......... .................... ............. ................... ................... .................... .......... ....
T echnical Product Spe cificati on 11 Intel ® Ne tStructu re™ ZT 7102 Chass is Manage ment Module Con ten ts 46 Threshold Response Forma ts ......................... ................... .................... ................... ............... 1 10 47 String Re sponse Form ats .
12 T echnical Product Spe cification Intel ® NetS tructure™ ZT 7102 Cha ssis Mana gement Mod ule Content s Revision History Date Revision Description August 2004 0 17 Changes related to V4.1 1h firmware Added new BIST events for RTC and FRU checking.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Introduction T echnical Product Spe cificati on 13 1.0 In trodu ction 1.1 Overview The Intel ® NetStructure TM ZT 7102 is a 3U, sin gle-slot Chassi s Managem ent Module (CMM) intended for use with PIC MG* 2.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Introduction 14 T echnical Product Spe cification Figure 1. Functional Block Diagram.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Introduction T echnical Product Spe cificati on 15 1.3 T erms Used in This Document T abl e 1.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Introduction 16 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Hardware Spe cification s T echnical Product Spe cificati on 17 2.0 Hardw are S pecificati ons 2.1 Overview The chassis manag ement module (CMM) is intended to op erate as a chassis management bu ilding block in a CompactPCI chassis.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Hardwa re Speci fications 18 T echnical Product Spe cification 2.2 System Architecture 2.3 B ackplane Connections 2.3.1 Slot Connections The slots are connected t o the CMM via an IPMB defined in the PI CMG* 2.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Hardware Spe cification s T echnical Product Spe cificati on 19 2.3.2 Chassis Sen sor Connections Chassis sensors are con n ected to the CMM via one two-wire serial bus. 2.3.3 Chassis FRU Device Connections Chassis sensors ar e connected to the CMM via o n e two-wire serial bus.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Hardwa re Speci fications 20 T echnical Product Spe cification 2.6 Face Plate Figure 3. Face Plate.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Hardware Spe cification s T echnical Product Spe cificati on 21 2.6.1 Facepla te Fea tur es The following featur es are found on the faceplate of the ZT 71 02: T abl e 2.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Hardwa re Speci fications 22 T echnical Product Spe cification 2.7 Mechanical 2.7.1 Board Dimensions and W e ight In a compatible enclosure, the ZT 7102 occupies a single 3 U CMM slot. Mechanical dimen sions are shown in Figur e 4 and outlined in Ta b l e 3 .
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Hardware Spe cification s T echnical Product Spe cificati on 23 J7, T able 12 T elco Alarm Connector (uDB-15, 15-pin) J8, SODIMM Socket (144-pin) J9 Connector r eserved f or test. Figure 5.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Hardwa re Speci fications 24 T echnical Product Spe cification 2.8.1 J1 Backplane Connector J1 is a 1 10-contact, 2 mm x 2 mm female CompactPCI form-factor con nector (AMP 35 2152-1).
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Hardware Spe cification s T echnical Product Spe cificati on 25 2.8.3 J 3 Backpl ane Connector J3 is a 55 -contact 2 mm x 2 mm female CompactPC I form-factor connecto r (AMP 3521 15-1). See Ta b l e 7 for pin definitions and Figure 6 for relative pin placement.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Hardwa re Speci fications 26 T echnical Product Spe cification 2.8.4 Backplane Pin Descriptions T able 8. Pin T ype Definitions Pin T ype Definition OD Open Drain I Input I/O Input/Output O Output T able 9.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Hardware Spe cification s T echnical Product Spe cificati on 27 2.8. 5 J A1 E thernet Port JA1 i s an R J-45 E thern et por t pro vi ding 10 Mbit (10B ASE- T) and 100 Mb it (1 00BA SE -TX) protocols .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Hardwa re Speci fications 28 T echnical Product Spe cification 2.8.6 J6 Serial Port J6 is an RJ-45 connector providing a front-panel RS -2 32 serial port interface. Serial port signals are also directed out connector J1 to the backplane.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Hardware Spe cification s T echnical Product Spe cificati on 29 2.9 Electrical and Environme nt al The ZT 7102 requires +5 VDC ±5% @ 1.8 A ty pical. CMM power comes fro m the backplane's IPMI_PWR rail; other voltages are derived as needed.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Hardwa re Speci fications 30 T echnical Product Spe cification 2.9.2 Power Ramp Circuitry The ZT 7102 features a power controller with power ramp circuitry to allow the boar d’ s v oltages to be ramped in a con trolled fashion.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Hardware Spe cification s T echnical Product Spe cificati on 31 2.9.6 DC Operating Ch aracterist ics 2.10 Onbo ard Switches The ZT 7102 contains a push-button switch on the faceplate and on e bank of DIP s witches on the component sid e of the bo ard.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Hardwa re Speci fications 32 T echnical Product Spe cification 2.10.1 Swit ch De sc ript ions The following topics pro v ide a detailed description of each switch. 2.10.1.1 S1 (Alarm Cutoff a nd Board Reset) S1 is a push button at the faceplate of the ZT 7102.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Hardware Spe cification s T echnical Product Spe cificati on 33 2.12 Memory The ZT 7102 includes 128 Mbytes of SDRAM on a Small Outline Dual Inline Memo r y Module (SODIMM). The S ODIMM used is 16 Mbits x 72 PC13 3 unbuffered SDRAM with ECC on a 144- pin m odule .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Hardwa re Speci fications 34 T echnical Product Spe cification 2.16 T elco Alarm Signal 2.16.1 Alarm Re lays The ZT 710 2’ s alarm r elay circuits ar e cap able of carrying 60 VDC or 1 A, wit h a maximum ra ting of 30 V AC.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Hardware Spe cification s T echnical Product Spe cificati on 35 Enable RF C 868 T ime Protocol on CMM ( client): 1. Create file "/etc/ rdate.cfg". 2. Edit file "/etc/rdate.cfg" with a valid h ost na me o r IP addres s of an enab led RFC 86 8 Time Protocol server .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Hardwa re Speci fications 36 T echnical Product Spe cification Caution: The ZT 7102 contai ns a lith ium bat tery . Do not disassemb le or rechar ge the battery . Do not disp ose of the battery in fire.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Sof tware S pe cific ation s T echnical Product Spe cificati on 37 3.0 Sof twar e S pec ifications 3.1 Operating System The CMM runs a cus tomized version of embed ded BlueCat * Li nux* 4.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Sof tware S pecifica tions 38 T echnical Product Spe cification In a platform containing redundant CMMs , upon ini tial power up, both CMMs will have identical IP addresses on all of their Ethern et interfaces.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module CMM Redund ancy , Synchronizati on and F ailover T echnical Product Spe cificati on 39 4.0 CMM Redundancy , Sy nchron ization and Failover 4.1 Overview The CMM supp orts red undant op eration w ith automa tic failover i n chass is using redundant CMM slots.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e CMM Redundanc y , Synchron iza tion and Failo ver 40 T echnical Product Spe cification Wa r n i n g : The /.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module CMM Redund ancy , Synchronizati on and F ailover T echnical Product Spe cificati on 41 4.4 CMM Failover Once information is synchronized between the redundant C MMs, the acti ve CMM will constantly monitor its own health as well as the health of the standby CMM.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e CMM Redundanc y , Synchron iza tion and Failo ver 42 T echnical Product Spe cification Note: The frequency o f the pi ng to the f irst tr ap address can vary fr om one second to appr oximately 20 seconds.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module CMM Inst allation and Re moval T echnical Product Spe cificati on 43 5.0 CMM Ins t allatio n and Remo val This chapter describes the steps necess ary to install and set up the Z T 7102 Chassis Management Module (CMM).
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e CMM Inst allation and Re moval 44 T echnical Product Spe cification 3. Prepare the new/replacement CMM by opening its ejector handle ( refer to Figu re 8 ). 4. C arefully align the edges of th e board with the card guides in the CMM slo t.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module CMM Inst allation and Re moval T echnical Product Spe cificati on 45 Note: Removing t he CMM before s afely sh utting it d own is highly discou raged. Corruption of t he flas h could occur if th e CMM is yanked su ddenly during a flash operation.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e CMM Inst allation and Re moval 46 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Built-In Self T est T echnical Product Spe cificati on 47 6.0 Built-In Self T est The CMM provides for a Built-In Self T est (BIST). The test will be run automatically after power-up or front-panel reset.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Built-In Self T est 48 T echnical Product Spe cification The BIST is broken d own into s tages consi sting of groups of tests ru n at seri ous times throug hout the boot pr oces s. Ta b l e 2 0 shows the diff erent B IST st ages and the tests ass ociated with each s tage: 6.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Built-In Self T est T echnical Product Spe cificati on 49 6.5 Late-BIST Late-BIST involves dis abling the watchdog timer t o indicate a s uccessful boot of RedBoot.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Built-In Self T est 50 T echnical Product Spe cification At OS start-up, the CMM will read th e contents of BIST results in the r eserved event log area an d store the errors as entries in the CMM SEL.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Built-In Self T est T echnical Product Spe cificati on 51 6.8 BIST T est Descriptions 6.8.1 Flash Ch ecksum T est This test is targeted to verify the RedBoot image and FPGA image are not corrupted.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Built-In Self T est 52 T echnical Product Spe cification 6.8.4 FPGA V ersion Che ck This test is targeted to verify the cor rect FPGA image programmed into both FPGA chip s. This test will display the FPGA version on both FPGAs.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module CMM Connectio n and Se tup T echnical Product Spe cificati on 53 7.0 CMM Connecti on and Setu p 7.1 CLI Overview The Command Line Interface (CLI) connects to and com municates with the intelligent management d evices of t he ch assi s , boar ds , and t h e CMM itself.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e CMM Co nnection and Setup 54 T echnical Product Spe cification 7.2.3 FTP Into the CMM Using an FTP client, FTP to th e IP addres s of th e CMM y ou wis h to transfer files to or from. 7.3 Initial Setup - Lo gging in fo r the First Time The default usern ame for the cmm is ro ot .
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module CMM Connectio n and Se tup T echnical Product Spe cificati on 55 7.3.1.1 Setting IP Inf ormation (I P Address, Netmask, and Ga teway) Eth0 1. Open the /etc/ifcfg -et h0 fi le using th e vi editor 2.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e CMM Co nnection and Setup 56 T echnical Product Spe cification 7.3.2 Setting a Hostname The hostname of the C MM is a logical name that is used to identify a par ticular CMM. This name is shown at login time and advertised to any DNS servers on a networ k.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Command Line Interface (CLI) Synt ax and Argument s T echnical Product Spe cificati on 57 8.0 Command Line Interface (CLI) Synt ax and Argume nt s The command line in terface on the CMM s upports two types of commands: c mmgets and cmmsets.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Command Li ne Interfa ce (CLI) Synt ax and Argument s 58 T echnical Product Spe cification 8.4 T arg et Parameter: -t The T arget parameter is the s ensor or variable that the cmm get or cmmset acts on.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Command Line Interface (CLI) Synt ax and Argument s T echnical Product Spe cificati on 59 thresholdsall All thresholds of a sensor . This includes lower non-recoverable, lower critical, lower non-critical, upper non-critical, upper c ritical, and upper non-recoverable.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Command Li ne Interfa ce (CLI) Synt ax and Argument s 60 T echnical Product Spe cification T able 26.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Command Line Interface (CLI) Synt ax and Argument s T echnical Product Spe cificati on 61 8.6 V alue Parameter: -v The V alu e p arameter specifies the new value for a Dataitem. This parameter is r eq uired for all cmmset commands and i s onl y used for cmmset com mands.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Command Li ne Interfa ce (CLI) Synt ax and Argument s 62 T echnical Product Spe cification 8.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Rese tting the Pa sswor d T echnical Product Spe cificati on 63 9.0 Resetting the Password It may become necessary to reset the CMM passwor d to its default of cmmrootpass . The CMM has an onboard dip switch labele d SW1-1 to perform this act ion.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Resetting the Password 64 T echnical Product Spe cification 9. O pen the ejector latch on the standby CMM and wait for the blue hot swap LED to illuminate, indicating the CMM is safe to remo ve from th e system.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Sensor T ypes T echnical Product Spe cificati on 65 10.0 Sensor T ypes The CMM provid es access to and can log events fro m dif ferent IPMI sens or types.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Sensor T ypes 66 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Health Even t String s T echnical Product Spe cificati on 67 1 1.0 Health Event S trings This section describes the health event str in gs th at are associated with CMM events and includes the syntax and severity of thes e strings.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Health Even t String s 68 T echnical Product Spe cification 1 1.1.3 SNMP T rap Event S y ntax The following is the syn tax of each SN MP t.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Health Even t String s T echnical Product Spe cificati on 69 1 1.3 Healthevent s Queries Healthevents queries, whether done from th e CL I or through SN MP , output the s ame event s trings and syntax for active events.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Health Even t String s 70 T echnical Product Spe cification Executing a healthevents qu ery through SNMP on a target with no active events return s diff erent values than the CLI do es . When a h ealth events query is executed in SNMP on: • A location target ( i.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Health Even t String s T echnical Product Spe cificati on 71 1 1.4.1 All Locations Note: For Thresh old-b ased se nsor e vents , stri ngs for SE L entries are the same ex cep t they begin with the word “Crossed” (i.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Health Even t String s 72 T echnical Product Spe cification 1 1.4.3 CMM Location T able 31. BIST Eve nt S trings (BIS T) (Sheet 1 of 2) Event String Event Code Event Severity “Boo t is Su cces sfu l.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Health Even t String s T echnical Product Spe cificati on 73 1 1.4.4 Chassis Location Note: Chassis power sup p ly detected and removed events are only gen erated wit h IPMI power supplies.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Health Even t String s 74 T echnical Product Spe cification T able 3 6. S lot Event Strings (Slot N E vent) Event String Event Code Event .
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Health Even t String s T echnical Product Spe cificati on 75 Note: In the CMM Redundancy and Failo ver event strings, the phrases “bad switch” and “switch failure” refer to the switch that is associated with that CMM having deasserted its HEAL THY# signal.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Health Even t String s 76 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Slot Power Control T echnical Product Spe cificati on 77 12.0 Slot Power Control The chassi s management module control s power to the node and fabric s lots of a chassis using the BD_SEL# and HEAL THY# hardware si gnals.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Slot Power Control 78 T echnical Product Spe cification 12.2.1.3 Fabric and P C I-Less Slot s For node slots co nt aining no PCI bus (PCI-less slots) as well as fabric slots, the CMM will always assert BD_SEL#.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Slot Power Control T echnical Product Spe cificati on 79 Board HEALTHY# signal is asserted Board has been powered up by the CMM Board is in active mode. For further info rmation on active and offline mode see Section 15.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Slot Power Control 80 T echnical Product Spe cification The maximum pow er- up attempts variable is used t o configure the number of times the CMM will attempt to p ower on a board during the power s equencing l oop.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Slot Power Control T echnical Product Spe cificati on 81 Note: T o set the maxpowerupattempts b ack to the defau lt value of -1, you need to have a s pace between the first quote an d the number 1 (i.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Slot Power Control 82 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Power Supplies T echnical Product Spe cificati on 83 13.0 Power Supplies 13.1 Power Supply Detection Unlike blades, there is no ha rdware support for th e detection of power supply presence.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Power Supplies 84 T echnical Product Spe cification 13.5 Inhi biti ng Po wer Supplies Power supplies can be inhi bited through the CMM.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Drone Mode SBC Support T echnical Product Spe cificati on 85 14.0 Drone Mode SBC Support An SBC is said to be “dro ne mode capable” if it can be configured to ignore the PCI_RST# s ignal coming from the PCI bus when inserted in a periphe r al slot in a CompactPCI chassis.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Drone Mode SBC Support 86 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Active vs. Offlin e Slots T echnical Product Spe cificati on 87 15.0 Active vs. Offline Slot s A slot operating normally is in what is defined as an active mode. The CMM has the capability to place a slot in an o ffline mo de.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Active vs. Off line Slot s 88 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Obt aining FRU Info rmation T echnical Product Spe cificati on 89 16.0 Obt aining FRU Information The CMM has t he ability to obtai n FRU inform atio n from IPMI 1.0 and hi gh er comp lian t devi ces.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Obt aining FRU In formation 90 T echnical Product Spe cification 16.3 Chassis FRU V alidity Check Chassis FRU v alidity is read on a periodic basis (e very 24 hrs ).
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Fan Contro l and Monito r ing T echnical Product Spe cificati on 91 17.0 Fan Control and Monitoring The CMM controls the fan speeds an d the fan tray LEDs. In a healthy s tate (no events) the LED changes to a g reen color .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Fan Control a nd Monitoring 92 T echnical Product Spe cification Note: Once the CMM automatically drives the fan speed s to 10 0 percent becaus e of one of the above health events, it is still possible to set the fa n sp eeds to 80 or 0 through th e supported interfaces (CLI, etc).
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module CMM Scripting T echnical Product Spe cificati on 93 18.0 CMM Scripting 18.1 CLI Scripting In addition to calling the C LI directly , commands can easily be called through scripts u sing “bas h” shell scripting.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e CMM Scripting 94 T echnical Product Spe cification Note: If applicable, remember to set a scrip t f or when a sensor retur ns to no rmal (No rmalAction). A script will not automati cally stop running when a sensor returns to a normal sett ing ( no alar ms or events).
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module CMM Scripting T echnical Product Spe cificati on 95 18.4 Setting Event Script s Setting event scripts ca n be done us ing any o f the standard C MM interfaces (CLI , SNMP , RPC).
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e CMM Scripting 96 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module SNMP T echnical Product Spe cificati on 97 19.0 SNMP The CMM supp orts the S imple Net work Man agement Pr otocol ( SNMP). The C MM can suppor t SNMP queries and send SNMP traps in v1 or v3 .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e SNMP 98 T echnical Product Spe cification 19.1 CMM MIB The CMM comes wi th a text fi le (ZT 71 02. mib) tha t descri bes the CMM o bjects to be managed , as well as all of the ma nage d objects in the platform .
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module SNMP T echnical Product Spe cificati on 99 Note: Changing IP ad dresses when using SNMP v3 w ill requ ire a restart of the snmpd process . This is due to SNMP v3 u sin g the IP add ress to gen erate the encr yption keys .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e SNMP 100 T echnical Product Spe cification 19.4 SNMP T rap Util ity The SNMP trap utility is u tilized by the CMM management s oftware to send SNMP trap mess ages to a remote ap plication regarding an y abnormal system events.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module SNMP T echnical Product Spe cificati on 101 T o check the status of SNMP traps, issue th e command: cmmget -l cmm -d SNMPenable 19.5.3 Alert s Using SNMPv3 The CMM utilizes the SNMPtrap utilit y to sen d the SNMP v3 ‘trap ’ mess age .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e SNMP 102 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module RPC T echnical Product Spe cificati on 103 20.0 RPC In addition to the command-line interface, the CMM may b e administered by custom remote applications thro ugh an RPC.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e RPC 104 T echnical Product Spe cification 20.2.1 GetAuthCap ability() The following is the callin g syntax for GetAuthCapability(): int Ge.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module RPC T echnical Product Spe cificati on 105 void ** ppvbuffer , unsign ed int * uReturnT ype ); Parameters pszCMM Host [in] IP A ddress or DNS hostname of CMM. nAuthCo de [in] Authentication code returned by GetAuth Capabil ity().
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e RPC 106 T echnical Product Spe cification T able 4 5. E rror and Return Codes for the RP C Interface ( Sheet 1 of 4 ) Code #: Error Code S.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module RPC T echnical Product Spe cificati on 107 34 E_IMB_COMPCODE_ERROR An IPMI request returned with a non successful completion code. User should try the command again. 35 E_IM B_INV ALID_ P ACKET Invalid IPMI respon se.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e RPC 108 T echnical Product Spe cification 64 E_SF S_NO_MEMORY Internal CMM Er ror 65 E_SF S_UNSUPPORTED_DE VICE Internal CMM Er ror 66 E_S.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module RPC T echnical Product Spe cificati on 109 Note: Error codes 100 and 101 will never be returned by the CMM when using RPC. If you receive these error codes, they are most likely bein g returned by the RPC client.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e RPC 110 T echnical Product Spe cification 20.2.4 C hassisMa nagement A pi () String Response Format The following table docu ments the format of ChassisManagementApi() queries that return data of type DA T A_TYPE_STRING .
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module RPC T echnical Product Spe cificati on 111 healthevents List of human-readable health events. Lines are separated by line feeds with a null-terminator at the end. "(null)” or "" if there are no health events Refer to Section 1 1.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e RPC 112 T echnical Product Spe cification redundancy Human-readable redundancy information containing t he current CMM redundancy status. Lines are separated by line feeds with a null-terminator at the end.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module RPC T echnical Product Spe cificati on 113 20.2.5 ChassisManagem entApi( ) Integer Response Format The following table do cuments the for mat of ChassisManag ementApi() queries that retur n data of t y p e D A TA _ T Y P E _ I N T.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e RPC 114 T echnical Product Spe cification 20.2.6 FRU S tring Response Format Querying an individual FRU field returns a null ter m inated string with a single line feed.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module RPC T echnical Product Spe cificati on 115 20.3 RPC Sample Co de Sample code for interfacing with the CMM through RPC is av ailable in the file cli_client.c. The sample code compiles into a command -line executable for us e with Linu x o r a .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e RPC 116 T echnical Product Spe cification T able 5 0. R PC Usage Examples (Sheet 1 o f 3) Example ChassisMa nagementApi() [ in] parameters ChassisManagementApi() [ out] parameters Get th e chassis temperature.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module RPC T echnical Product Spe cificati on 117 Get the CMM’s overall health. psz CMM Ho st : localhost uCmdCode : CMD _GE T pszLocation : C.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e RPC 118 T echnical Product Spe cification Enable the SNMP Trap s. psz CM MHo st : localhost uCmdCode : CMD_SET pszLocation : chassis pszDa.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Command L ogging T echnical Product Spe cificati on 119 21.0 Command Logging All CMMSE T commands from all of the CMM interf aces (CLI, RPC, and SNMP) are logged by the CMM under /var/log .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Command Lo gging 120 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module T elco Alarm Sensors T echnical Product Spe cificati on 121 22.0 T elco Alarm Sensors The faceplate of the C MM contains a µDB15 T elco alarm connector . See Section 2.6, “Face Plate” on page 20 and Section 2.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e T elco Alarm Sensors 122 T echnical Product Spe cification 22.3.1 Sensor Na mes using SNMP The telco alarm senso r names that will be show n via SNMP will be those that are defined at CMM startup.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Application Hosting T echnical Product Spe cificati on 123 23.0 Application Hosting The ZT 7102 al lows applications to b e hosted locally . This is useful as a method for ad ding small custom management u tiliti es to the CMM.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Application Hostin g 124 T echnical Product Spe cification 23.3.1. 2 RAM-Disk S torage Locations Caution: F iles in this location are stored in RAM , and will be lost during CMM r eboots.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Busless Back plan e Sup port T echnical Product Spe cificati on 125 24.0 Busle ss Ba ckpl ane Support The ZT 7102 s upports bus less PICMG* 2.16 ba ckplanes. Busl ess backplanes are P ICMG 2.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Busless Bac kplane Suppo rt 126 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Up dating Sof tware T echnical Product Spe cificati on 127 25.0 Up d ati ng Sof tware When new CMM updates are av ail able, they are p ack aged in a zip file and posted to the I ntel web site located at: http:// www .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Updati ng So ftware 128 T echnical Product Spe cification 25.3 Critical Sof tware Up date Files and Directori es The following table is a list o f files and di rectories important to the software upd ate process.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Up dating Sof tware T echnical Product Spe cificati on 129 The update package can be placed locally on the CMM in the /usr/local/cmm/temp director y , or it can reside on a s erver on th e network.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Updati ng So ftware 130 T echnical Product Spe cification T o determine if the update is a new , old or same versi on, the update p ackage will co nt ain a version_his tory fil e w hich contain s a lis t of all so f tware builds that have occurred, listed in sequential order .
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Up dating Sof tware T echnical Product Spe cificati on 131 25.6 Update Mode T o perform the update, the C MM will enter an update mode to p revent interfer ence from ot her processes that may write to th e flash and to unmo unt the JFFS2 drives that may need to be repartitio ned.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Updati ng So ftware 132 T echnical Product Spe cification 25.8 Synchronization Following a f irmware update to t he standb y CMM in a re dundant C MM, some leve l of synchroni zation w ill occur .
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Up dating Sof tware T echnical Product Spe cificati on 133 25.8.3 Upda ting to the Same Synchronization V ersion Following an update on t.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Updati ng So ftware 134 T echnical Product Spe cification user a nd passw ord - Optional argument that is the username and password for the FTP server . Note: The -v ar gument can be u p to 64 characters long.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Up dating Sof tware T echnical Product Spe cificati on 135 Note: In prior versions of th is d ocument, the following examples show ed how to u se the user scripts to replace a script in the /etc/scripts directory .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Updati ng So ftware 136 T echnical Product Spe cification newversion=$4 cp /home/stagingarea/myScript.$newversion /home/s cripts/myScript exit $? 25.13 Up date Process 1. C lient initiates an update request via CLI comm an d 2.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Up dating Sof tware T echnical Product Spe cificati on 137 12. U pdate Com ponents (listed i n UpdateMetadata f ile) — If a componen t .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Updati ng So ftware 138 T echnical Product Spe cification 25.17 RedBoot Up date Process The firmware can also be update d through Red boot. This updat e is done at a pre-O S level, meaning that the update is executed bef ore the OS loads.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Example C LI Comm ands T echnical Product Spe cificati on 139 Appendi x D Example CLI Co mmands The followi ng tabl e shows exam ples of most CLI operations.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Example C LI Comm ands 140 T echnical Product Spe cification Get a blade’ s FRU information cmmget –l blade [ 1-19] –d fru A list of FRU information. Find out what sensors are on blade 3.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Data sheet Reference T echnical Product Spe cificati on 141 Appendi x E Dat asheet Reference This appendix provides lin ks to datas heets , st andards, and specifications for the techn ology designed i nto the CMM.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Dat asheet Reference 142 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module W a rra nty Information T echnical Product Spe cificati on 143 Appendi x F W arranty Informa tion F.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e W a rranty Inform ation 144 T echnical Product Spe cification DRA on-line form : http://s upport.i ntel. com/supp ort/moth erboards/draform. htm Intel Business Link (IBL): http://www .intel.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module W a rra nty Information T echnical Product Spe cificati on 145 PRODUCT , WHETHER ARISING OUT OF CONTRA CT , NEGLIGENCE, TOR T , OR UNDER .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e W a rranty Inform ation 146 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Customer Support T echnical Product Spe cificati on 147 Appendi x G Custome r Support This appendix off ers technical and s ales assistance information for th is product, an d information o n returning an Intel NetStructure product for service.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Customer Supp ort 148 T echnical Product Spe cification.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Agency Approvals T echnical Product Spe cificati on 149 Appendi x H Agency Appro vals H.1 CE Certific a tio n The ZT 7102 meets the intent of Directive 89/336/EEC for Electromagnetic Compatib ility and Low-V oltage Directive 73 /23/EEC fo r Product Safety .
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Agency Approv als 150 T echnical Product Spe cification EN 61000 4-6 Frequency Magnetic Fi elds EN 61000 4-1 1 V oltage Dips, V ariations , and Sho rt Inter ruptions H.4 R egulatory Inf ormation H.
Inte l ® NetS tructure TM ZT 710 2 Chassis Manage ment Module Agency Approvals T echnical Product Spe cificati on 151 Wa r n i n g : To A void Electric Overload: T o avoid electrical hazards (heat sh ock and/or fire h azard), do no t make connections to terminals outside the r ange sp ecifi ed for that terminal.
Intel ® NetS tructure TM ZT 7102 Chassis Manage ment Modul e Agency Approv als 152 T echnical Product Spe cification.
An important point after buying a device Intel ZT 7102 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Intel ZT 7102 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Intel ZT 7102 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Intel ZT 7102 you will learn all the available features of the product, as well as information on its operation. The information that you get Intel ZT 7102 will certainly help you make a decision on the purchase.
If you already are a holder of Intel ZT 7102, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Intel ZT 7102.
However, one of the most important roles played by the user manual is to help in solving problems with Intel ZT 7102. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Intel ZT 7102 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
