Instruction/ maintenance manual of the product J-SHOWER TOWERTM Jacuzzi
Go to page of 28
WHIRLPOOL BA TH R INST ALLA TION AND OPERA TING MANUAL J-SHOWER T OWER ™ ENCLOSURE-Siena ™ , Merano ™.
.
1 Important The bathtub must be installed per installation instructions D884000 for the Merano™ or E160000 for the Siena™. Follow the instructions to ensure that proper framing has been provided to support the J-Shower Tower. Finishing materials must be waterproof and sealed so that spray and condensation do not cause moisture damage.
2 BAILS SEE P AGE 7 W ALLBAR SEE P AGE 9 F EXTRUSION SEE P AGE 20 L EXTRUSION SEE P AGE 20 TOP RING SEE P AGE 17 W ALL BRACKET SEE P AGES 17 &18 TOWER SEE P AGE 12 HANDLE SEE P AGE 21 HAND HELD SH.
3 EXPLODED VIEW OF J-SHOWER TOWER END CAP SEE P AGE 20 BOTTOM RAIL SEE P AGE 15 & 16 SET SCREW SEE P AGE 16 PINS SEE P AGE 1 1 F AC EPLA T E SEE P AGE 21 MIXER/DIVERTER (INCLUDING HOSE CONNECTIONS.
4 Shower T ower Hardware Identification Chart The diagrams for these fasteners are shown actual size for fast identification. HARDW ARE SCREW COVER COVER QTY .-6 H10 SET SCREW #8-32 x 1 1/2" SCREW QTY .-1 H17 LOWER TRACK END CAP CAP QTY . -1 H16 EXTERNAL T O OTH LOCK-WA SHER #8 ST A INLESS STEEL W A SHER QTY .
5 Shower T ower Hardware Identification Chart The diagrams for these fasteners are shown actual size for fast identification. W A T ER INLET HARDW ARE NUT QTY .-1 W2 LOCKNUT 1/2"-14NPT FIBRE W ASHER 1.24 DIA W A SHER QTY .-1 W1 W ALL BAR HARDW ARE FLA T HEAD SCREW #10-24 x 2 1/2" ST A INLESS STEEL SCREW QTY .
6 Shower T ower Hardware Identification Chart PLUMBING HARDW ARE The diagrams for these fasteners are shown actual size for fast identification. FIBER WA SHER .75 O.D. W A SHER QTY .-2 SCREW QTY .-6 PHILL IPS HEAD SCREW M4X12 ST AINLESS STEEL P3 W ASHER QTY .
7 T OWER ASSEMBL Y 1. Assemble the four (4) bails to the tower wall. Do not overtighten the nuts on the threaded shaft end. Overtightening may break the stud. ILLUSTRA TION 1 BAIL SET SCREW (8) BOL T (8) H1 SHELF NUT (8) H2 H3 W ASHER (8) H1 BOL T QTY .
8 2. Attach the water inlet and fill spout to the tower wall. (See Illustration 2 and 2a.) ILLUSTRA TION 2a FILL SPOUT NUT QTY .-1 W2 LOCKNUT 1/2"-14NPT FIBER W ASHER 1.
9 3. Attach the wallbar assembly to the tower wall. (See Illustration 3.) ILLUSTRA TION 3 FLA T HEAD SCREW #10-24 x 2 1/2" ST A INLESS STEEL EXTERNAL T OOTH W ASHER 1/8" BEAD OF CAULK W ALLB.
ILLUSTRA TION 5 A TT ACHING DIVER TER V AL VE TO SHOWER W ALL SCREW QTY .-3 PHILL IPS HEAD SCREW M4X12 ST AINLESS STEEL EXTERNAL T OOTH LOCK W ASHER M4 P3 W ASHER QTY.
11 6. Attach the shower line to the water inlet and the fill spout line to the fill spout. (See Illustration 6.) 7. Attach the three (3) pins to the bottom of the tower. (See Illustrations 7 and 8.) 8. After these steps are completed, set the tower aside.
12 ILLUSTRATION 9 (LEFT HAND SHOWN) 1. Locate the drilling template. Place it over the bathtub. The inner orange circle must be centered over the circular opening of the bathtub. (See Illustration 9.) Be sure the orange circle is spaced an equal distance around the bath cavity.
13 ILLUSTRATION 10 3. Attach Hot and Cold water supply lines of the mixer/diverter to the stub-out supply lines. (See Illustration 10.) 4. Locate the on/off handle and temporarily place it on the mixer valve. (See Illustration 26.) With the mixer/ diverter valve in the OFF position, turn on the water supply.
14 PLACING TOWER ILLUST RATI ON 11 5. Dry fit tower pins into holes to check hole location. Apply sealant around the three tower wall holes on the bath and around the perimeter where the tower will set. (See Illustration 11.) 6. Place the tower pins in the holes and push the tower down firmly.
7. Locate the bottom rail and the fixed panel. Lay a bead of sealant on the bottom of the fixed panel. Secure the bottom rail to the fixed panel. (See Illustration 12.) Drill a 3/32" diameter hole into the bottom rail at about 15 ° . Drill only through the first aluminum thickness.
16 FIXED PANEL ASSEMBLE TO BATH 8. Screw 1-1/2" Allen set screw 3/4" deep into the bottom of the fixed panel. Lay a 1/4" bead of sealant under the bottom rail and inside the vertical frame. Place the assembly against the vertical edge of the tower and onto the bath surface.
17 9. Locate the top ring. Remove the plastic retainer extrusion and set it aside. Place the top ring on the fixed panel and tower wall. The top ring groove on the underside of the top ring must mate with the top of the fixed panel. The flat portion of the ring should be parallel with the back wall.
18 11. Drill a 3/32" diameter hole into the top ring at about 15 ° . (See Illustration 20.) Engage the top of the fixed panel with the top ring groove. Secure the top of the fixed panel to the top ring. (See Illustration 21.) 12. Plumb and square the tower.
19 FIXED GLASS FRAME ATTACHMENT 13. Apply sealant in frame and extrusion. Align and place extrusion above end cap onto the fixed glass. ILL U STRA T I ON 23 SEALANT FIXED GLASS END EXTRUSION.
20 14. Install on the sides of the tower the aluminum extrusions provided. They may be sealed in place or secured with screws. Seal the end cap and place into the end of the lower track.
15. Assemble the face plate as shown in Illustration 25. Assemble the handle as shown in Illustration 26 (See handle instructions in handle kit). ILL U STRA T I ON 25 A TT ACHING F ACE PLA TE HANDLE I.
2I. Attach the shower hose. (See Illustration 27.) Use the washer supplied with the shower hose. 22. For hot and cold operation of the handle, see Illustration 28.
.
.
.
Printed in the U.S.A. PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type.
An important point after buying a device Jacuzzi J-SHOWER TOWERTM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jacuzzi J-SHOWER TOWERTM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jacuzzi J-SHOWER TOWERTM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jacuzzi J-SHOWER TOWERTM you will learn all the available features of the product, as well as information on its operation. The information that you get Jacuzzi J-SHOWER TOWERTM will certainly help you make a decision on the purchase.
If you already are a holder of Jacuzzi J-SHOWER TOWERTM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jacuzzi J-SHOWER TOWERTM.
However, one of the most important roles played by the user manual is to help in solving problems with Jacuzzi J-SHOWER TOWERTM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jacuzzi J-SHOWER TOWERTM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
