Instruction/ maintenance manual of the product E70 Jura
Go to page of 19
IMPRESSA E70/75 Instructions for use 2/02 Art. Nr. 62564.
Jura Impressa E70/75 English ................................................................................................................ 6 – 19 Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Tip Jura Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.
Fig. 1 Fig. 4 Fig. 7 Fig. 2 Fig. 5 Fig. 8 Fig. 3 Fig. 6 Fig. 9.
7 8 9 11 12 13 14 15 16 17 18 6 5 4 3 2 1 10 8 8b 8a Operating elements Jura Impressa E70/75 1 Water quantity switch 2 Powder coffee selection switch 3 Coffee key for 2 cups 4 Rinsing-, cleaning-, des.
5 Contents Jura Impressa E70/75 1. Description .................................................. page 6 2. Safety instructions ........................................ page 6 2.1 Warnings .............................................. page 6 2.2 Safety precautions .
6 Important information for the user Thank you for choosing this Jura product. Please study these instructions carefully before using your new machine for the first time and keep them in safe place for easy reference in future.
7 3. Preparation of the machine 3.1 Checking the mains voltage The machine is set to the correct voltage before leaving our factory. Ensure that your mains voltage corresponds to the details quoted on the rating plate attached to the bottom of the machine.
8 The symbols on the display mean: HARDNESS LEVEL — Water hardness function switched off HARDNESS German water hardness 1 – 7° LEVEL 1 French water hardness 1.79 – 12.53° HARDNESS German water hardness 8 – 15° LEVEL 2 French water hardness 14.
9 6. Adjusting the water quantity The water quantity can be infinitely adjusted with rotary knob (1). The small key means little water for espresso, the large cup means a lot of water for coffee.
10 Never use water-soluble instant coffee or quick coffee. We recommend that you only use powder from freshly ground coffee beans or pre-ground, vacuum-packed coffee. Never put more than 2 portions of coffee in. The filler funnel is not a storage container.
11 When you have reached the required quantity of hot water, turn the steam/hot water rotary knob (15) back to the position . SELECT PRODUCT At the start of a water draw-off, there can be splashes. The pivoting nozzle gets hot. Please avoid direct contact with the skin.
12 12.4 Fill beans FILL BEANS Fill beans as described in Chapter 3.4. The display FILL BEANS only goes off after coffee has been drawn off. We recommend cleaning the bean container from time to time with a dry cloth before you refill beans. Switch the machine off for this purpose.
13 12.8 Insert filter Pull up the cartridge holder. Pressing gently, put the filter cartridge into the water tank (Fig. 7). Close the cartridge holder until it engages audibly. Fill the water tank with cold fresh tap water and put it back into the machine.
14 12.10 General cleaning instructions Never use abrasive articles or corrosive chemicals to clean your machine. Wipe down the casing on the inside and out using a soft, damp cloth. Clean the pivoting nozzle after each use. After heating milk, draw off a little hot water in order to clean the inside of the pivoting nozzle.
15 ADD TABLET (Fig. 9) / PRESS RINSE UNIT CLEANING / PLEASE WAIT An acoustic signal can be heard. EMPTY TRAY Wait for about 10 seconds before you put the drip tray back in again. PRESS RINSE UNIT CLEANING / PLEASE WAIT An acoustic signal can be heard.
16 FILL WATER / OPEN TAP / PRESS RINSE Turn the selector switch for coffee or hot water / steam (13) to position and press the rinsing key . UNIT DECALCING / PLEASE WAIT An acoustic signal is heard.
17 17. Messages Cause Action SYSTEM EMPTY System empty Fill system (see point 4.1) FILL WATER The tank is empty Fill with water Floater defective Rinse out or descale water tank FILL BEANS The bean container is empty Fill up with beans Although beans have been poured in, Draw off a cup of coffee.
18 18. Problems Problem Cause Action Grinder is very noisy – foreign body in grinder – Drawing off coffee with pre-ground powder – is still possible – Have machine examined by Jura service cen.
19 20. Technical data Voltage: 230V AC Power consumption: 1350 W Fuse: 10 A Safety check: Energy consumption standby: approx. 3 Wh Energy consumption ready to make coffee: approx.17 Wh Pump pressure: max. 15 bar Water tank: 1.9 litres Capacity, bean container: 200 gr.
An important point after buying a device Jura E70 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jura E70 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jura E70 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jura E70 you will learn all the available features of the product, as well as information on its operation. The information that you get Jura E70 will certainly help you make a decision on the purchase.
If you already are a holder of Jura E70, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jura E70.
However, one of the most important roles played by the user manual is to help in solving problems with Jura E70. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jura E70 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
