Instruction/ maintenance manual of the product Millenium ADC Analog/Digital Converter Lyngdorf Audio
Go to page of 24
Owner´s manual Millenium ADC Analog/Digital Converter.
2.
3 T able of Contents Unpacking the Millennium ADC 4 Operating V oltage 4 Serial Number Registration 4 Introduction 5 Accessories 6 Front Panel 7 Rear Panel 8 Remote Control 9 Placement 10 Millennium L.
4 Unpacking the Millennium ADC Carefully remove the unit and accessory kit from the carton, visually check for shipping damage. Contact both the shipper and your L yngdorf Audio dealer immediately if the unit bears any sign of damage from mishandling.
5 Introduction Congratulations on your investment in the L yngdorf Audio Millennium ADC (Analog to Digital Converter). The L yngdorf Audio Millennium ADC is a high-performance 2-channel Analog to Digital Converter with 4 line inputs.
6 Accessories Y ou should fi nd the following accessories included: 1 2 3 4 5 6 7 digital info analog A/B random repeat AMP channel ENTER volume RCS CD TUNER menu 8 0 9 Mains cord Millennium Link cab.
7 Front Panel 1 2 3 6 4 5 Figure 1: Millennium ADC front panel. The buttons/controls on the front panel of the TDAI 2200 can all be operated either with direct presses or by operating the corresponding keys on the supplied remote control. All the keys on the front panel [except the Mains switch (1)] are duplicated on the remote control as well.
8 Rear Panel Figure 2: Millennium ADC rear panel. 1. Binding post for phono ground. 2. Optional phono stage module. 3. Millennium ADC serial number label. 4. RS-232 AUX and INPUT RJ45 connectors. The RS-232 communication connectors are for connection to a computer for fi rmware upgrade.
9 Remote Control The remote control is used to access the menu system and replicate the buttons directly accessible on the front panel. The four buttons used for selecting which device to control are described below . T o control the Millen- nium ADC the AMP key should be pressed.
10 Placement The Millennium ADC should be placed well away from any source of magnetic fi elds like wall mains adapters. Also avoid placing on top of a power amplifi er – instead place them ‘side by side’. Figure 3. Recommended placing of the Millennium ADC.
11 Menu T ree Common Menus Main Menu ADC Dig . Samplerate Comm . Address Comm . Speed Display Timeout Remote Control Factory Reset Input Related Menus Input Related Menus Main Menu ADC High Pass Filter De - emphasis Select Cartridge Setup Cartr . : 1 Polarity Phono Cartridge: 1 50 kHz Zero DSP Cart .
12 Menu Operation In the following the general menu operation is described with Display T imeout menu (used as an exam- ple only). The menus available depend on the selected input. All settings outside the common menus apply to the selected input only .
13 Common Menus Digital Sample Rate A vailable sample rates are 48, 96 and 192 kHz. Choice of sample rate depends on the compatibility with the actual amplifi er . If your amplifi er accepts all sample rates, we recommend you to test the different settings to fi nd your personal preference.
14 Phono Input Menus High Pass Filter The high pass fi lter can be chosen to fi lter away rumble and/or acoustic feedback. A vailable settings are 10, 15 or 20 Hz. This is referred to as the F2 point in fi g. 4. De-emphasis Records made before 1955 were recorded with different emphasis curves, requiring different de-empha- sis during playback.
15 Setup Cartr .: 1 Load Preset If you use one of the pre-loaded cartridges you can load this directly which then automatically sets up the ADC to this cartridge (gain, capacitance, impedance and DSP cartridge fi lter). If you have a different cartridge, you need to make these settings manually .
16 Input sensitivity versus cartridge output specifi cation The output voltage of cartridges are generally specifi ed at a stylus velocity of 5 cm/sec. High performance turntable/tone arm/cartridge combinations can track up to 50-75 cm/sec resulting in an output of 10 to 15 times the output voltage specifi ed for the cartridge.
17 Cartr . Balance The Cartridge Balance adjustment enables you to compensate for differences between left and right channel. The balance is adjusted by decreasing the left or right channel between 0 - 3dB. Cartr . Capacit. The cartridge capacitance can be set to 100 or 430pF .
18 Analog Input 1- 4 Menus Input Gain The Input Gain enables you to match levels from different sources as well as obtaining full scale output on your amplifi er . The Input Gain can be adjusted up to +18dB in 0.1 dB steps. Please refer to the output level specifi cations of the source and then use the table in fi g.
19 T echnical Specifi cations Analog inputs Parameter V alue Note Balanced input connectors 3 pin XLR female, gold plated Case=Gnd, Pin1=Gnd, Pin2=Hot(+), Pin3=Cold(-) Balanced input CMRR -40dB 20 Hz-20 KHz. Unbalanced input connectors RCA (phono) jack, gold-plated.
20 Digital outputs Parameter V alue Note Balanced output connector 3 pin XLR male, gold-plated Case=Gnd, Pin1=Gnd, Pin2=Hot(+), Pin3=Cold(-) Balanced output impedance 110 ohms T ransformer isolated output. Balanced output voltage 1.7Vpp With 110 Ohm load.
.
22.
23.
24 www .lyngdorf.com.
An important point after buying a device Lyngdorf Audio Millenium ADC Analog/Digital Converter (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lyngdorf Audio Millenium ADC Analog/Digital Converter yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lyngdorf Audio Millenium ADC Analog/Digital Converter - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lyngdorf Audio Millenium ADC Analog/Digital Converter you will learn all the available features of the product, as well as information on its operation. The information that you get Lyngdorf Audio Millenium ADC Analog/Digital Converter will certainly help you make a decision on the purchase.
If you already are a holder of Lyngdorf Audio Millenium ADC Analog/Digital Converter, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lyngdorf Audio Millenium ADC Analog/Digital Converter.
However, one of the most important roles played by the user manual is to help in solving problems with Lyngdorf Audio Millenium ADC Analog/Digital Converter. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lyngdorf Audio Millenium ADC Analog/Digital Converter along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
