Instruction/ maintenance manual of the product 5620DWB Makita
Go to page of 20
SPE( Mo Man 4 Note WAR& SAVE lped with Electric Brake IL5620DWA MODEL 5620DWB !h Capacity Battery Charger With High Capacity Battery Charger INSTRUCTION MANUAL CATIONS 620D Cutting depth No load speed Overall Net 900 450 (RPMI length weight 364 mm 3.
GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit.
Pa mc to: M; to< *Ch ott sei *Us wt Sen Tot ma owt in I to !TIC tform. Holding the work by hand or against your body is unstable and to loss of control. use tool if switch does not turn it on or off. A tool that cannot be ed with the switch is dangerous and must be repaired.
Specific Safety Rules 1. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. Keep your body positioned to either side of the saw blade, but not in line with the saw blade.
11 iauses and Operator Prevention of Kickback: rickback is a sudden reaction to a pinched, bound or misaligned saw blade, ausing an uncontrolled saw to lift up and out of the workpiece toward the Iperator.
Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICK BACK.
15 16 17 ace the wider portion of the saw base on that part of the workpiece which solidly supported, not on the section that will fall off when the cut is made. E examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, id Fig. 6 the WRONG way.
SYMBOLS The followings show the symbols used for tool. V ................................. volts A ................................. amperes Hz ................................. herts kg ................................. kilograms h ..................
I @1 2 3 4 5 6 7 8 *9 10 11 12. Length of Cord (Feet) 25 50 AWG Size of Cord 18 18 IPORTANT SAFETY INSTRUCTION’S FOR CHARGER & BATTERY CARTRIDGE 100 150 18 16 9.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents.
Ins *A *TI it *TI tC 91 A PI di tc .D ei Ch .YI Y( tt D *PI tt in *In ai tr rc bi in .V rE *V ai cl 01 01 CP *TI N *LA fc dc it ,, illing or removing battery cartridge lays switch off the tool before insertion emoval of the battery cartridge.
*If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools.
He W co CI AI ar AI LC m Ai bi C .I ., B L a ti 0 Bevel scale plate wrench storage n not in use, the eniently stored. Screw hex wrench can be TION: iys be sure that the tool is switched off and the battery cartridge is removed before adjustment is attempted.
Adjusting for accuracy of 90" cut (vertical cut) This adjustment has been made at the factory. But if it is off, adust the adjusting screw with a screwdriver while squaring the blade with the base using a triangular rule, try- square, etc. Base I Fig.
01 Hc thi mi an Nc thi ad sa ad . co CL @P tc S @Ii ti GI Th ex thi thc thi al: PO pation the tool firmly. Set the base plate on vorkpiece to be cut without the blade ng any contact.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes reg- ularly. Replace when they wear down to the limit mark.
R To 1. 2. A 0 Tt m Tt .I f .I f 01 F Part No. Diameter Hole diameter (mm) (mm) cycling the Battery No, teeth The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd I cycle the battery: ?move the battery from the tool.
Juns-10-'98 US 165 mm (6-1/2") CORDLESS CIRCULAR SAW Model 5620D Note: The switch and other part configurations may differ from country to country.
MCI MAKVA LIMrlED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from worfknshrp and materials for period of ONE YEAR from the date of original purchase.
MODEL 56200 "",M ,,!& DESCRIPTION MACHINE 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 1 11 1 12 1 13 1 14 1 15 1 16 1 17 I 10 1 10 2 20 1 21 1 22 3 23 6 24 1 25 2 26 1 27 1 26 1 29 1 30 1 31 .
An important point after buying a device Makita 5620DWB (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 5620DWB yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 5620DWB - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 5620DWB you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 5620DWB will certainly help you make a decision on the purchase.
If you already are a holder of Makita 5620DWB, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 5620DWB.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 5620DWB. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 5620DWB along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
