Instruction/ maintenance manual of the product HRH01 Makita
Go to page of 22
Capacity: mm (") HR262D/ BHR262 (HRH01C/ HRH01) *1 HR262TD/ BHR262T (HRH02C/ HRH02) *1 Yes Yes Yes (by trigger) 13 (1/2) 32 (1-1/4) 26 (1) 4.5 (9.9) Models No. Description C ONCEPT AND MAIN APPLICATIONS S pecification S tandard equipment O ptional accessories Note: The standard equipment for the tool shown above may vary by country.
P 2/2 2 V ariation list BHR262Z2C BHR262RD Model No. Type Quantity Battery adapter Battery converter Plastic carrying case Battery cover Yes Battery BHR262DP1 No No BHR262Z No 1 No No No No BAP36N BCV.
[2] LUBRICATION [1] NECESSARY REPAIRING TOOLS R epair Description Code No. Use for Retaining ring S pliers ST-2N 1R003 Removing Ring spring 19 from Tool holder complete/ Tool holder guide complete Ret.
Gear section: 17g Crank section: 5g boss for fixing Compression spring 14 [Inside view of Inner housing] [2] LUBRICATION (cont.) Apply Makita grease RB No.00 to the following portions indicated by black triangle to protect parts and product from unusual abrasion.
[3] DISASSEMBLY/ASSEMBLY [3] -1. Bit holder section for BHR262, HR262D Holder section for Drill chuck of BHR262T, HR262TD DISASSEMBLING for BHR262, HR262D DISASSEMBLING for BHR262T, HR262TD Ring 21 Ring 21 Guide washer Conical compression spring 21-29 Cap 35 Steel ball 7.
a Note: Face the chamfered end of the hole upward. Aligning the hole of Change ring with that of Change cover, assemble Change ring to Change cover. a' [Section a - a'] (1) Assemble Change ring to Change cover. ( Fig. 6 ) (2) Assemble Torsion spring 31 to Tool holder, then mount Steel balls 6 to Tool holder.
[3] DISASSEMBLY/ ASSEMBLY [3] -2. Drill chuck assembly for BHR262T, HR262TD DISASSEMBLING Fig. 10 Fig. 11 Fig. 14 Fig. 13 Fig. 12 Steel ball 5.0 Leaf spring Flat washer 24 Drill chuck assembly can be disassembled as drawn in Figs.
Change cover Change ring ASSEMBLING Chuck holder short arm of Torsion spring 31 long arm of Torsion spring 31 hole for Torsion spring 31 (1) Holding Chuck holder's flat portions in vise, assemble Drill chuck to Chuck holder by turning it clockwise using Hex wrench 10.
[3] DISASSEMBL Y/ASSEMBL Y [3]-3. Change lev er While pushing Lock button into Change lever, turn Change lever a little over Drill mode position to lock it in place. While pushing Lock button into Change lever, fit Change lever completely to Gear housing complete.
[3] DISASSEMBL Y/ASSEMBL Y [3]-4. Motor section, Switch Remove two Pins 6 and two 4x18 Tapping screws, then separate Handle (R) from Handle (L). Switch can now be replaced. (Also see Figs. D-1 and D-2 .) Remove two Pins 6 and Handle section from Housing (L) to disassemble Motor section.
[3] DISASSEMBL Y/ASSEMBL Y [3]-4. Motor section, Switch (cont.) Remove Brush holder on the right side by unscrewing two 4x18 Tapping screws. Motor section and Gear section can now be removed as an assembly. Brush holder (on right side) 4x18 Tapping screw (2 pcs.
When inserting Armature into Inner housing complete, do not fail to pass Armature through Yoke unit in advance. Note : Yoke unit is not directional when assembled with Armature. Without enough care, Ball bearing 6001DDW on the drive-end of Armature may often be incompletely seated in the bearing room of Inner housing complete.
[3] DISASSEMBL Y/ASSEMBL Y [3]-5. T ool holder section for BHR262, HR262D/ T ool holder guide section for BHR262T, HR262DT DISASSEMBLING Inner housing complete Flat washer 28 Piston cylinder Swash bearing section Take the disassembling step in reverse.
[3] DISASSEMBL Y/ASSEMBL Y [3]-6. Needle bearing complete and Oil seal 25 DISASSEMBLING Fig. 34 Fig. 37 ASSEMBLING 1) Assemble Oil seal 25 to Gear housing complete.
[3] DISASSEMBL Y/ASSEMBL Y [3]-7. Impact bolt in T ool holder complete for BHR262, HR262D)/ T ool holder guide complete for BHR262T, HR262TD DISASSEMBLING (1) When Striker is left in Tool holder (guide) complete, push Striker out of Tool holder (guide) complete by inserting 1R281 from the top end then by striking 1R281 with plastic hammer.
Note: 2) ASSEMBLING Fig. 42 Cushion ring 13 Ring 10 O ring case with O ring 9 fit inside Impact bolt 1) Assemble Impact bolt section to Tool holder (guide) complete as drawn in Fig. 42 . Tool holder (guide) complete Sleeve 9 Bit (chuck) installation side Inner housing complete side long short Fig.
[3] DISASSEMBL Y/ASSEMBL Y [3]-8. Swash bearing 10, Gear section DISASSEMBLING Fig. 44 Note : This step can be done without removing Motor section. 1) Remove Gear housing complete as instructed in [3]-5 . 2) Remove Inner support complete by loosening two M4x25 Hex socket head bolts using 1R170.
[3] DISASSEMBL Y/ASSEMBL Y [3]-8. Swash bearing 10, Gear section (cont.) ASSEMBLING Fig. 51 Fig. 52 Guide plate Note: Be sure to apply Makita grease RB No.
[4] Maintenance program It is recommended to replace the following parts at the same time when replacing Carbon brushes. ( Fig. 55 ) Note : Be sure to put Makita grease RB No. 00 and Molybdenum disulfide lubricant to the specific portions. Refer to Figs.
Color index of lead wires' sheath Black Terminal LED Brush holder Switch M1 White Red Fig. D-1 Terminal LED Line filters Switch C ircuit diagram P 2 0 /2 2 W ith Equipment of Radio Interference S.
W iring diagram Fig. D-2 T o Brush holder complete Connector Connector ribs Diode Switch Lead wire holders FET (Field effect transistor) Lead wires must be tight in the area shown in gray . Fix lead wires in the Lead wire holders indicated by dotted circle .
Lead wire (yellow) Terminal Line filters Tube Connector Lead wire (black) Yoke Connector FET Fig. D-3 Lead wire holder Lead wire holder Fix Lead wires (red, black) of Brush holder complete in these Lead wire holders. rib Light circuit W iring diagram P 2 2 /2 2 Line filter is not used for some countries.
An important point after buying a device Makita HRH01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita HRH01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita HRH01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita HRH01 you will learn all the available features of the product, as well as information on its operation. The information that you get Makita HRH01 will certainly help you make a decision on the purchase.
If you already are a holder of Makita HRH01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita HRH01.
However, one of the most important roles played by the user manual is to help in solving problems with Makita HRH01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita HRH01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
