Instruction/ maintenance manual of the product Q4.80 Maxxsonics
Go to page of 13
System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup.
Index 1 W ARRANTY 4-5 Q4.80 / Q4.150 4 -Channel Amplifiers 6-7 Q1.1500D Mono Amplifier 2 General Instructions 3 Features 8 Settings for Best Performance 1 W ARRANTY 1 T rouble Shooting 9 T echnical Data 10 Chec k out our videos of new pr oducts, e v ents and tec hnical tutorials a t www .
General Instructions 2 General: Run the wiring so that RCA cables are at least 18“ away from power and speaker cables. Keep RCA cables away from electrical devices in the vehicle that can cause electrical noise, such as electric fuel pumps, emission control modules and other on-board electronic modules.
Features Q4.80 / Q4.150 / Q1.1500D Q4.80 Q4.150 Q1.1500D 3 - CLIP INDICA TOR: - GREEN = Pre-Clip - AMBER = Soft Clip - RED = Hard Clip - LEVEL: V ariable sensitivity from 0.
4-Channel Amplifiers Q4.80 / Q4.150 4 4 Channel Full Range Stereo: INPUT MODE: 4CH since 2 sets of RCA ’s are connected. Interconnect cable checklist: - Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables.
4-Channel Amplifiers Q4.80 / Q4.150 5 4 Channel Full Range Stereo With Mono Amp For Subwoofers: -RCA ’s from OUTPUT on 4CH amp to INPUTS on MONO amp. Interconnect cable checklist: - Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables.
Mono Amplifiers Q1.1500D 6 Interconnect cable checklist: Connect the inputs to a suitable source, e.g. a head unit with good quality RCA cables. Control checklist: Refer to the section “Settings for Best Performance” Use at least #12 gauge speaker wiring.
Linking Mono Amplifiers Q1.1500D 7 DESIGNA TED MONO OUTPUT FROM HEAD UNIT POWER INPUT POWER INPUT BATT+12V R EM GND BATT+12V R EM GND SPEAKER OUTPUT SPEAKER OUTPUT - - + + - - + + FUSE FUSE MONO SUBWO.
Settings for Best Performance 8 Q1.1500D General: At this point you are ready to get more specific on the settings for your amplifier . Phase: Time alignment, typically recommended at 0 degrees unless using multiple amps and subs in both the front and rear of the vehicle.
Tr ouble Shooting 9 The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the Diagnostic system built into all MB Quart amplifiers The diagnostic system will shut down the amplifier, until reset by turning the head unit of f, and back on.
10 70Amps x 2.
1 1 OEM Integration Accessories MX-1 Premium High T o Low Level Converter Low Level Outputs * High Level Inputs: Accepts all types of High level Inputs including floating ground and high voltages up to 30 volts. * Audio Signal Sense / Hardwire T urn-On: Audio sense detects music signals from the OEM wires and activates the MX-1.
P ART#S510 Chec k out our videos of new pr oducts, e v ents and tec hnical tutorials a t www .y outube.com/maxxsonicsusainc Q4.80 / Q4.150 / Q1.1500D.
An important point after buying a device Maxxsonics Q4.80 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Maxxsonics Q4.80 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Maxxsonics Q4.80 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Maxxsonics Q4.80 you will learn all the available features of the product, as well as information on its operation. The information that you get Maxxsonics Q4.80 will certainly help you make a decision on the purchase.
If you already are a holder of Maxxsonics Q4.80, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Maxxsonics Q4.80.
However, one of the most important roles played by the user manual is to help in solving problems with Maxxsonics Q4.80. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Maxxsonics Q4.80 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
