Instruction/ maintenance manual of the product ESW 408X-14 Miele
Go to page of 44
Operating and Installation Instructions Built-in Warming Drawer ESW 408x-14 ESW 47xx ESW 48xx To prevent accidents and machine damages, read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS .................................3 Guide to the warming drawer ........................................7 ESW 408x-14 ......................................................7 ESW 47xx / ESW 48xx ............................
WARNING- When using your appliance follow basic precautions, including the following: Read all instructions before installation or use to prevent injury and appliance damage. This appliance conforms to all uniform safety codes and regulations. Keep these operating instructions in a safe place and pass them on to any future user.
Technical safety ~ Before installing the appliance, check for externally visible damage. Do not operate a damaged appliance. ~ Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply.
Safety ~ Protect your hands with oven mitts or potholders when using the appliance. Use only dry, heat resistant potholders. Moist or damp potholders used on hot surfaces can result in steam burns. ~ Be aware of loose fitting or hanging clothing while using the warming drawer.
~ The use of accessories not recommended by Miele may cause injury. ~ Make certain that the power cords of small appliances do not come in contact with the appliance. The insulation of the cable could become damaged. Danger of electric shock! ~ Do not lean, sit or overload the warming drawer.
ESW 408x-14 a Control panel b Non-slip mat Guide to the warming drawer 7.
ESW 47xx / ESW 48xx a Control panel b Non-slip mat c Vent d Rack Guide to the warming drawer 8.
Control panel On/Off Turns the warming drawer On and Off Menu Allows you to select the operating mode Operating modes: / Cups/glasses H Tableware 2 Food - warm and hold Temp. Allows you to select the desired temperature. The display shows: ]^^^^ See "Temperature settings" for more information.
When first connecting the appliance to the power supply and after a power failure, the fan will run and a display test will be carried out for approx. 10 seconds. The appliance cannot be used during this time. Clean the appliance ^ Remove any protective wrapping.
Operating modes Tap the " Menu " touch control until the desired operating mode lights: – / Cups/Glasses – H Tableware – 2 Food - warm and hold The last operating mode selected appears in the control panel when the drawer is turned on.
Temperature settings Each operating mode has an assigned temperature range. The suggested temperatures are set by default, they are marked in bold in the table below.
Duration The warming drawer is set for continuous operation by default. By selecting the " Timer " touch control a warming time can be set. With each tap of the " Timer " touch control the duration will increase in one hour increments, beginning with 1 hour and ending with 4 hours.
Sabbath Mode For religious observance, the appliance can be set for the duration of the Sabbath. In Sabbath mode the timer is deactivated and the sensors have to be touched longer than ususal. If Sabbath mode is activated, the appliance will turn off after approx.
The drawer load will depend on the type and size of your dishes. The maximum load is 55 lbs (25 kg). Do not overload the drawer. To increase the load space use the supplied rack. Two racks will fit in the drawer at one time. Additional racks are available from Miele.
Tips The warming drawer is intended for keeping food warm directly after preparation. It is not intended to re-warm cold meals. – To ensure that the minimum temperature of 150°F (65°C) required to keep food warm is met, select 2 . – Preheat the warming drawer for approx.
Settings Food Type of container Lid on container Temperature for 2 setting Position in drawer Floor Rack* Bacon Plate no ^ ^ ] ^ ^ xx Beef** Rare / Medium / Well Pan yes ] ^ ^ ^ ^ xx Bread hard rolls .
Tips – Distribute tableware throughout the entire drawer. Stacked plated will heat up more slowly than individual pieces. If stacking is unavoidable please them in the front of the drawer. Use the rack (depending on model). – Do not place platters right up against the vents.
The warming drawer can also be used to proof yeast dough or to warm or crisp bread. Proofing dough ^ Open the drawer. ^ Turn the appliance on " On/Off ". ^ Touch " Menu " to select the " / Cups/Glasses" setting. ^ Touch " Temp .
Allow the appliance to cool before cleaning. Do not use a steam cleaner to clean this appliance. Pressurized steam could penetrate electrical components and cause a short circuit. Do not use commercial cleaning agents. Only use agents recommended for domestic use.
, Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. What if the drawer does not heat? Possible fault Solution There is no power to the warming drawer.
In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance.
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and machine damage read these instructions before installation or use.
~ Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond in order to avoid risk of damage to the appliance. If in doubt, consult a qualified technician.
Miele appliances can be installed flush or proud. Discuss your installation requirements with your architect, designer and installer. Combination possibilities Installation with an oven a Cut-out for .
Installation with a speed oven * Machine with glass front ** Machine with stainless steel front ESW 408x-14 26 (560 mm -568 mm) (455.5 mm) (22*/23**mm) (593 mm - 595 mm) (541 mm) (595 mm) (548 mm) (14.
Installation with a steam oven * Machine with glass front ** Machine with stainless steel front ESW 408x-14 27 (560 mm -568 mm) (455.5 mm) (22*/23**mm) (593 mm - 595 mm) (444 mm) (595 mm) (548 mm) (14.
Installation with a coffee machine * Machine with glass front ** Machine with stainless steel front ESW 408x-14 28 (560 mm - 568 mm) (455.5 mm) (20 mm) (593 mm - 595 mm) (460 mm) (595 mm) (548 mm) (14.
Combination possibilities Installation with an oven a Cut-out for venting the oven * Machine with glass front ** Machine with stainless steel front ESW 408x-14 BRWS 29 (734 mm - 736 mm) (30 mm) a (596.
Installation with a speed oven * Machine with glass front ** Machine with stainless steel front ESW 408x-14 BRWS 30 (560 mm -568 mm) (455.5 mm) (22*/23**mm) (593 mm - 595 mm) (541 mm) (595 mm) (548 mm.
Installation with a steam oven * Machine with glass front ** Machine with stainless steel front ESW 408x-14 BRWS 31 (560 mm -568 mm) (455.5 mm) (22*/23**mm) (593 mm - 595 mm) (444 mm) (595 mm) (548 mm.
Installation with a coffee machine * Machine with glass front ** Machine with stainless steel front ESW 408x-14 BRWS 32 (560 mm - 568 mm) (455.5 mm) (20 mm) (593 mm - 595 mm) (460 mm) (595 mm) (548 mm.
Solo installation Side view a A base is required for solo installations ESW 47xx 33.
Installation with an oven Side view with oven ESW 47xx 34.
Solo installation Side view a A base is required for solo installations ESW 48xx 35.
Installation with an oven Side view with oven ESW 48xx 36.
Miele appliances can be installed flush or proud. Discuss your installation requirements with your architect, designer and installer. Check that the base of the warming drawer is clean and level. Only then will it function properly. When inserting the appliance, wear work gloves to avoid injuries.
Aligning the appliance front After installation it may be necessary to align the appliance front and/or the gap between the appliances/furniture front above. ^ Remove the screws a from the left and right sides of the drawer front. ^ Carefully lift the control panel out of the drawer.
^ Loosen the 2 screws b on the inside of the drawer front. ^ Align the front. ^ Tighten the screws on the inside of the drawer front. ^ Replace the control panel, use caution with the power cord. ^ Replace the screws on the left and right sides of the drawer front.
Integrated installations Custom made front panels can be installed with models ESW 4702 FB and ESW 4802 FB. The custom panel must be at least 3 / 8 " (19 mm) thick and made of heat resistant material 140 °F (60 °C). The front panel, including handle, must not exceed 11 lb (5 kg) in weight.
^ Remove the cable tie from the panel. ^ Screw the removed panel to the custom panel (see illustration). ^ Hook the panel into the bottom. Make sure the seal is seated correctly. ^ Replace and slightly tighten the screws on the inside of the drawer front.
, CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards.
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of an old appliance Old appliances contain materials that can be recycled.
Alteration rights reserved / 4611 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
An important point after buying a device Miele ESW 408X-14 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele ESW 408X-14 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele ESW 408X-14 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele ESW 408X-14 you will learn all the available features of the product, as well as information on its operation. The information that you get Miele ESW 408X-14 will certainly help you make a decision on the purchase.
If you already are a holder of Miele ESW 408X-14, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele ESW 408X-14.
However, one of the most important roles played by the user manual is to help in solving problems with Miele ESW 408X-14. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele ESW 408X-14 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
