Instruction/ maintenance manual of the product WS6-50NF Moog Videolarm
Go to page of 12
P R O D U C T I N S T R U C T I O N S INST ALLA TION PREP ARA TION INST ALLA TION PREP ARA TION 1. Choose an appropriate corner location. The WS6 can be mounted at any height in a corner . 2. Complete all wire and conduit runs prior to installation of the housing.
- 2 - CAMERA BRACKET SE TUP 8. T o adjust the camera bracket, loosen the two thumb screws (Figure 6). When the desired focus and location are achieved tighten the thumb screws on the brackets in place using needle nose pliers. Use Loctite™ or equivalent to secure the screws, especially in installations where vibration is a concern.
- 3 - Figure 7 CAMERA FOCUSING (Figur e 7) 1. The camera is factory equipped with a 3.6mm xed lens. A 2.5mm lens is also provided. T o remove the 3.
- 4 - WINDOW GU ARD™ P AINT SHIELD REPLACEMENT Y our W arrior 6 comes with a replaceable Window Guard™ paint shield to protect the front plate window from vandalism. If vandalism occurs (spray paint, scratches, etc.) you need only replace the shield, not the entire window .
2 50 f t 3 4 5 8 13 W 3 00 f t 4 5 6 10 16 W 4 00 f t 5 6 8 13 21 W 5 00 f t 6 8 10 16 26 W 6 00 f t .
- 6 - IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS UNPACKING SERVICE 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 Do not block any of the ventilation openings.
6 5 4 3 2 1 WS6 - Exploded Diagram and Replacement P ar ts List P ar t Number Description 1 RPWS6010 W ARRIOR 6 F ACE PLA TE F ASTENER KIT 2 RPWS6020 W ARRIOR 6 FRONT PLA TE ASSEMBL Y 3 WS6PS W ARRIOR.
P ower Supply P ower A P ower B Camera Assembly Primar y P ower Video Signal Video Shield Monitor - 8 - (Ground Return) Figure A Ground Loop TROUBLESHOO TING If you experience problems with the camera picture please check these simple troubleshooting procedures for possible solutions before calling technical support.
A C Vo l t m e t e r Camera Monitor Bridge Tap NV-213 A NV-213 A - 9 - NV T TROUBLESHOO TING If you a re experi encing p roblems , attempt to simpl ify your setup. T est each cable segment separate ly . For exa mple, te st the camera and monitor together with out the other equi pment.
- 10 - Depending on the voltage being used, refer to one of the formulas below to select the correct power supply for cameras connected in parallel (positive to positive, negative to negative): T otal.
- 1 1 - LIMITED W ARR ANT Y FOR VIDEOLARM INC. PRODUC TS VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship, as follows: PRODUCTCA TEGORY P ARTS LABOR All Enclosur.
- 12 - Pr oduct Registration / W arranty Thank you for choosing Videolarm. W e value your patronage and ar e solely committed to providing you with only the highest quality products available with unmatched customer service levels that ar e second- to-none in the security industry .
An important point after buying a device Moog Videolarm WS6-50NF (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Moog Videolarm WS6-50NF yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Moog Videolarm WS6-50NF - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Moog Videolarm WS6-50NF you will learn all the available features of the product, as well as information on its operation. The information that you get Moog Videolarm WS6-50NF will certainly help you make a decision on the purchase.
If you already are a holder of Moog Videolarm WS6-50NF, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Moog Videolarm WS6-50NF.
However, one of the most important roles played by the user manual is to help in solving problems with Moog Videolarm WS6-50NF. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Moog Videolarm WS6-50NF along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
