Instruction/ maintenance manual of the product LCD3090WQXi NEC
Go to page of 34
MultiSync LCD3090WQXi User ’ s Manual.
Index W arning, Caution ............................................................................................................... ......... English-1 Declaration ...................................................................................
English English-1 W ARNING CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . TO FULL Y DISENGAGE THE POWER TO THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET .DO NOT REMOVE COVER (OR BACK).
English-2 Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.
English English-3 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONIT OR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks.
English-4 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONIT OR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level.
English English-5 Contents Y our new NEC monitor box* should contain the following: • MultiSync LCD3090WQXi monitor with tilt/swivel/pivot/height adjust stand • Power Cord • Video Signal Cable (.
English-6 Figure C.1 Figure C.2 Quick Start T o attach the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” before installation. In order to display the maximum resolution, a video card that can output a resolution of 2560 x 1600 is needed.
English English-7 Figure E.1 V acation Switch Power Button Figure C.3 Figure D.1 Figure D.2 Figure C.4 7. Hold all cables firmly and place the cable cover onto the stand ( Figure D.1 ). T o remove the cable cover , lift the cover off as shown in Figure D.
English-8 T ilt Grasp top and bottom sides of the monitor screen with your hands and adjust the tilt as desired ( Figure TS.1 ). Figure TS.1 Swivel Grasp both sides of the monitor screen with your hands and adjust the swivel as desired ( Figure TS.2 ).
English English-9 Mount Flexible arm 1. Using the 4 screws from the stand removal and attach the arm to the monitor ( Figure F .1 ). Caution: • When mounting, use ONL Y the screws (4 pcs) that were removed from the stand to avoid damage to the monitor or stand.
English-10 Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: T o access OSD menu, press the MENU button. T o change signal input, press the SELECT button. NOTE: OSD must be closed in order to change signal input.
English English-11 Brightness/Contrast Controls BRIGHTNESS Adjusts the overall image and background screen brightness. NOTE: The upper portion (higher settings) of the brightness level is adjusted using the backlight output. If a very low brightness level (low setting) is used the contrast level may be reduced.
English-12 FINE (Analog input only) Improve focus, clarity and image stability by increasing or decreasing this setting. If the “Auto Adjust function” and the “H.Size” function do not give you a satisfactory picture setting, a fine tuning can be performed using the “Fine” function.
English English-13 HDCP CONTENT (Digital Input Only) Selects the type of input to be used with HDCP CONTENT . OFF: When a PC or other computer equipment is connected, select “OFF”. ON: When a DVD player or other type of high definition device is connected, select “ON”.
English-14 OSD LOCK OUT This control completely locks out access to all OSD control functions. When attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD controls are locked out.
English English-15 Specifications Monitor Specifications MultiSync LCD3090WQXi Monitor Notes LCD Module Diagonal: 75.6 cm/29.8 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 75.
English-16 Features DVI-I: The integrated interface ratified by the Digital Display Working Group (DDWG) that allows both digital and analog connectors of f of one port. The “I” stands for integration for both digital and analog, The digital portion is DVI-based.
English English-17 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Check the V acation Switch should be in the ON position.
English-18 T ag1 Brightness Adjusts the overall image and screen background brightness. Press “Left” or “Right” to adjust. When AUTO LUMINANCE is OFF or 2, the brightness level is adjusted/measured using percentage (%). When AUTO LUMINANCE is 1 or 3, brightness level is adjusted/measured using cd/m 2 .
English English-19 T ag2 R-H.position Adjusts the position of the red component of the image. Press “Left” or “Right” to adjust. (Analog input only) G-H.position Adjusts the position of the green component of the image. Press “Left” or “Right” to adjust.
English-20 H. Size Adjusts the horizontal size of the screen. (Analog input only) If the “AUTO Adjust function” do not give you a satisfactory picture setting, a further tuning can be performed using the “H.Size (V .Size)” function (dot clock).
English English-21 T ag6 Color Control Color Control Systems: Seven preset color settings. For preset settings 1, 2, 3 and 5, the following levels can be adjusted: TEMPERA TURE: Adjust the white temperature by increasing or decreasing this setting.
English-22 Response Improve Turns the R ESPONSE IMPROVE function on or off. Response Improve may reduce blurring that occurs in some moving images. When Response Improve is on, response time is improved. Side Border Color Adjusts the side black bars color between black and white.
English English-23 Hot Key When this function is activated; the brightness and contrast of the monitor can be adjusted without entering the OSD menu by using the front buttons. The “Left” or “Right” buttons adjust the brightness level. The “Down” or “Up” buttons adjust the contrast level.
English-24 T agA T ile Matrix The T ile Matrix feature allows one image to be displayed over multiple screens. This feature can be used with up to 25 monitors (5 vertical and 5 horizontal). Using T ile Matrix requires the PC output signal be sent through a distribution amplifier to each individual monitor .
English English-25 Figure S.4 Figure S.5 Figure S.3 Sensor Port USB Sensor Sensor port is located at the back of the monitor . Self Calibration Simply connect the external USB sensor , and the brightness, white tint and gamma levels are calibrated without the need of a computer .
English-26 Figure S.7 Figure S.8 Figure S.6 Figure S.9 7. The procedure will ask for the USB sensor to be placed on the center of the display panel ( Figure S.7 ). T ilt the display panel approximately 5˚ backward and place the USB sensor in the center of the display panel ( Figure S.
English English-27 Figure C.5 Figure C.6 Figure C.4 Sensor Port USB Sensor Sensor port is located at the back of the monitor . White Point Matching/Copy Calibration Calibration settings can be copied from one display to one or more additional displays.
English-28 Figure C.8 Figure C.9 Figure C.7 Figure C.1 1 6. Using “LEFT” or “RIGHT” of Display B, select COPY in the MODE selection ( Figure C.7 ). Select ON of OFF in the SELF selection. If ON selected, SELF Calibration execute with COPY Calibration.
English English-29 Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly .
English-30 TCO’03 Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world.
English English-31 TCO’06 Congratulations! The product you have just purchased carries the TCO’06 Media Displays label. This means that your display is designed and manufactured according to some of the strictest performance and environmental criteria in the world.
English-32 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment.
An important point after buying a device NEC LCD3090WQXi (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NEC LCD3090WQXi yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NEC LCD3090WQXi - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NEC LCD3090WQXi you will learn all the available features of the product, as well as information on its operation. The information that you get NEC LCD3090WQXi will certainly help you make a decision on the purchase.
If you already are a holder of NEC LCD3090WQXi, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NEC LCD3090WQXi.
However, one of the most important roles played by the user manual is to help in solving problems with NEC LCD3090WQXi. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NEC LCD3090WQXi along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
