Instruction/ maintenance manual of the product CM9760-KBD-E80 Pelco
Go to page of 12
System 9760 ® KBD/KBR Firmware Upgrade C1543M-A (7/04) ® INST ALLA TION MANUAL CM9760-KBD-E80.
.
C1543M-A (7/04) 1 INTRODUCTION The System 9760 ® keyboard upgrade kit, CM9760-KBD-E80, provides the following items to upgrade CM9760-KBD/CM9760-KBR firmware to version 8.
2 C1543M-A (7/04) 1 2 3 4 5 6 7 8 CABLE NO DIP SWITCH 7 Options Relay Com3 Com 2 Com1 Volu me Rese t (MAY HAVE RETAINING NUT) SCREW (9) UPGRADING CM9760-KBD FIRMW ARE CAUTION: Only qualified personnel observing electrostatic discharge (ESD) precautions should perform the procedure below .
C1543M-A (7/04) 3 CIRCUIT BOARD U4 U12 U5 U2 NOTCHED END OF EPROM ALIGNMENT NOTCH U3 U3 EPROM CHIP 6. Remove the existing U3 EPROM chip (refer to Figure 2) from its socket using the provided extraction tool. Remove the chip slowly to avoid damaging the socket.
4 C1543M-A (7/04) KEYBOARD SELECT ICON MOVE CURSOR/ CYCLE SELECTIONS LEFT ICON FORWARD STEP/ SCROLL UP ICON MOVE CURSOR/ CYCLE SELECTIONS RIGHT ICON BACKWARD STEP/ SCROLL DOWN ICON SAVE ICON EXIT ICON 11. Calibrate the joystick as follows: a. In Setup mode, select the Joystick Adjust icon.
C1543M-A (7/04) 5 UPGRADING CM9760-KBR FIRMW ARE CAUTION: Only qualified personnel observing electrostatic discharge (ESD) precautions should perform the procedure below . Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic components.
6 C1543M-A (7/04) CIRCUI T BOARD U3 U4 U12 U5 U2 U3 EPROM CHIP NOTCHED END OF EPROM ALIGNMENT NOTCH 5. Locate DIP switch 7 on the rear of the KBR (refer to Figure 4), and set the DIP switch to the correct position: • For compatibility with CM9760-CC1 and CM9760-MGR versions 7.
C1543M-A (7/04) 7 12. Calibrate the joystick as follows: a. In Setup mode, select the Joystick Adjust icon. The Joystick Setup menu appears (refer to Figure 7).
.
REVISION HISTORY Manual # Date Comments C1543M 4/03 Original version C1543M-A 7/04 Added factory-default reset and joystick calibration information Pelco, the Pelco logo, and System 9760 are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved.
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.
An important point after buying a device Pelco CM9760-KBD-E80 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco CM9760-KBD-E80 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco CM9760-KBD-E80 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco CM9760-KBD-E80 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco CM9760-KBD-E80 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco CM9760-KBD-E80, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco CM9760-KBD-E80.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco CM9760-KBD-E80. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco CM9760-KBD-E80 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center